Study on the low mechanical anisotropy of extruded Mg-Zn-Mn-Ce-Ca alloy tube in the compression process

In this study,the extruded Mg-Zn-Mn-Ce-Ca alloy tube with a low compression anisotropy along the ED,45ED and TD was prepared.The effect of the second phases,initial texture and deformation behavior on this low mechanical anisotropy was investigated.The results revealed that the alloy tube contains the high content(Mg1-xZnx)11Ce phase and the low content of Mg12Ce phase.These second phases are respectively incoherent and coherent with the Mg matrix,and their influence can be ignored.Additionally,the alloy tube exhibited a weak basal fiber texture,where the c-axis was aligned along the 0°∼30°tilt from TD to ED.Such a texture made the initial deformation(at 1.0%∼1.6%strain)of the three samples controlled by comparable basalslip.As deformation progressed(1.6∼9.0%strain),larger amounts of ETWs nucleated and gradually approached saturation in the three samples,re-orienting the c-axis to a 0°∼±30°deviation with respect to the loading directions.Meanwhile,the prismatic and pyramidal<c+a>slips replaced the dominant deformation progressively until fracture.Eventually,the similar deformation mechanisms determined by the weak initial texture in the three samples contribute to the comparable strain hardening rates,resulting in the low compressive anisotropy of the alloy tube.

Meso-mechanical anisotropy and fracture evolution of reef limestones from the Maldives Islands and the South China Sea

Reef limestone is a biogenic sedimentary rock widely distributed in coral reef areas, acting as an important foundation for coast construction. Due to its special biogenic origin, reef limestone is different from conventional rocks both in terms of rock structure and mechanical properties. In this study, mesoscale uniaxial compression experiments with five different loading directions were conducted on two kinds of reef limestones from the Maldives Islands and the South China Sea, respectively. The real-time high-resolution videos and images of failure processes were recorded simultaneously to investigate the fracture evolution and fracture surface roughness of reef limestones. It demonstrated that the reef limestones belonged to extremely soft to soft rocks, and their uniaxial compressive strength (UCS) values fluctuated with high discreteness. The mesoscale mechanical properties of reef limestones were highly anisotropic and mainly controlled by pore structure. The occurrence of dissolution pores in reef limestone tended to intensify mechanical anisotropy. With the integration of the fracture initiation and propagation features of reef limestones, it is supposed that the intrinsic mechanism of anisotropy was probably attributed to the differences in coral growth direction and dissolution. Furthermore, the quantified fracture surface roughness was revealed to have a good consistency with density and UCS for the reef limestones from the South China Sea. The findings are helpful for providing theoretical and experimental references for engineering construction in coral reef areas.

Mechanical Anisotropy of Selective Laser Melted Ti-6Al-4V Using a Reduced-order Crystal Plasticity Finite Element Model

In this study,a reduced-order crystal plasticity finite element(CPFE)model was developed to study the effects of the microstructural morphology and crystallographic texture on the mechanical anisotropy of selective laser melted(SLMed)Ti-6Al-4V.First,both hierarchical and equiaxed microstructures in columnar prior grains were modeled to examine the influence of the microstructural morphology on mechanical anisotropy.Second,the effects of crystallographic anisotropy and textural variability on mechanical anisotropy were investigated at the granular and representative volume element(RVE)scales,respectively.The results show that hierarchical and equiaxed CPFE models with the same crystallographic texture exhibit the same mechanical anisotropy.At the granular scale,the significance of crystallographic anisotropy varies with different crystal orientations.This indicates that the present SLMed Ti-6Al-4V sample with weak mechanical anisotropy resulted from the synthetic effect of crystallographic anisotropies at the granular scale.Therefore,combinations of various crystallographic textures were applied to the reduced-order CPFE model to design SLMed Ti-6Al-4V with different mechanical anisotropies.Thus,the crystallographic texture is considered the main controlling variable for the mechanical anisotropy of SLMed Ti-6Al-4V in this study.

Microstructure evolution and mechanical anisotropy of M50 steel ball bearing rings during multi-stage hot forging

This study aimed to explore the evolution of flow lines and microstructures of M50-steel bearing ring and the anisotropy of its tensile mechanical properties after Multi-Stage Hot Forging(MSHF) and subsequent spheroidizing annealing(MSHFA). To this end, the present study mainly employed stereo microscopy, Optical Metallurgical Microscopy(OMM), Scanning Electron Microscopy(SEM), and Electron Backscatter Diffraction(EBSD) to characterize and analyze the workpiece at each processing stage of MSHF while performing microhardness measurement and uniaxial tensile experiment to test and analyze the mechanical properties of the workpiece. Macro-structure observation showed that the simulation results of flow lines at each stage were consistent with the experimental results. Microscopic observation showed that, after MSHF, deformation gradually became less significant along the outward radial direction of the bearing ring. After MSHFA,the microstructures of the bearing ring became uniform, whereas primary carbides did not dissolve.The mechanical properties were better in the axial direction(AD) than in the radial(RD) and circumferential directions(CD) after MSHF due to the smaller grain width. After MSHFA, the mechanical properties in the ADs and CDs were better than those in the RDs, which was due to the large cross-sectional area of carbides along the flow-line direction.

Effects of icosahedral phase on mechanical anisotropy of as-extruded Mg-14Li (in wt%) based alloys

Through investigating and comparing microstructure and crystallographic texture of as-extruded Mg-14Li and Mg-14Li-6Zn-1Y(in wt%)alloys,the differences in their mechanical anisotropy were investigated.It revealed that the formation of I-phase(Mg3Zn6Y,icosahedral structure)can effectively refine grain size.Moreover,compared with Mg-14Li alloy,the texture type of Mg-14Li-6Zn-1Y alloy changed slightly,but its texture intensity decreased remarkably.As a result,the stronger texture contributed to the"normal"mechanical anisotropy of Mg-14Li alloy with higher tensile strength and a lower elongation ratio along transverse direction(TD)than those along extrusion direction(ED).However,for Mg-14Li-6Zn-1Y alloy,the zonal distribution of I-phase particles along ED caused"abnormal"mechanical anisotropy,i.e.higher tensile strength and better plasticity along ED.

Effect of Icosahedral Phase on Crystallographic Texture and Mechanical Anisotropy of Mg–4%Li Based Alloys

Through investigating and comparing the microstructure and mechanical properties of the as-extruded Mg alloys Mg-4%Li and Mg-4%Li-6%Zn-l.2%Y （in wt%）, it demonstrates that although the formation of I-phase （Mg3Zn6Y, icosahedral structure） could weaken the crystallographic texture and improve the me- chanical strength, the mechanical anisotropy in terms of strength remains in Mg-4%Li-6%Zn-1.2%Y alloy. Failure analysis indicates that for the Mg-4%Li alloy, the fracture surfaces of the tensile samples tested along transverse direction （TD） contain a large number of plastic dimples, whereas the fracture surface exhibits quasi-cleavage characteristic when tensile samples were tested along extrusion direction （ED）. For the Mg-4%Li-6%Zn-I.2%Y alloy, typical ductile fracture surfaces can be observed in both ＂TD＂ and ＂ED＂ samples. Moreover, due to the zonal distribution of broken l-phase particles, the fracture surface of ＂TD＂ samples is characterized by the typical ＂woody fracture＂.

Mechanical anisotropy and electronic properties of X2N2(XH2):first-principles calculations

The mechanical anisotropy,structural properties,electronic band structures and thermal properties of C2N2(CH2),Si2N2(SiH2)and Ge2N2(GeH2)are detailed and investigated in this work.The novel silicon nitride phase Si2N2(SiH2)and germanium nitride phase Ge2N2(GeH2)in the Cmc21 structure are proposed in this work.The novel proposed Si2N2(SiH2)and Ge2N2(GeH2)are both mechanically and dynamically stable.The electronic band calculation of the HSE06 hybrid functional shows that C2N2(CH2),Si2N2(SiH2)and Ge2N2(GeH2)are all wide band gap semiconductor materials,and C2N2(CH2)and Si2N2(SiH2)are direct band gap semiconductor materials,while Ge2N2(GeH2)is a quasi-direct band gap semiconductor material,the band gap of C2N2(CH2),Si2N2(SiH2)and Ge2N2(GeH2)are 5.634 eV,3.013 eV,and2.377 eV,respectively.The three-dimensional and plane distributions of Young’s modulus,shear modulus and Poisson’s ratio of C2N2(CH2),Si2N2(SiH2)and Ge2N2(GeH2)show that these materials have different degrees of mechanical anisotropy.The order of Young’s modulus of Si2N2(SiH2)and Ge2N2(GeH2)in different directions is different from that of C2N2(CH2).When the tensile axis is in a particular direction,the order of the Young’s modulus of Si2N2(SiH2):E[110]<E[120]<E[111]<E[101]<E[010]=E[100]<E[011]<E[001],and the order of the Young’s modulus of Ge2N2(GeH2):E[110]<E[111]<E[101]<E[120]<E[100]<E[010]<E[011]<E[001].

Relationship among Mechanical Properties Anisotropy,Microstructure and Texture in AA 6111 Alloy Sheets

We comparatively studied the mechanical properties anisotropy, microstructure and texture of the commercial and the new developed AA6111 alloys through tensile test, optical microscopy, and XRD analysis. The results show that the anisotropy of mechanical properties for the developed AA6111 alloy is lower than that of the commercial alloy. The developed alloy possesses higher r value, lower Ar value and more uniform microstructure, compared with the commercial AA6111 alloy, indicating that the deep drawability of the developed alloy has been improved significantly. The recrystallization textures of the two alloy sheets are also different. The recrystallization texture of the commercial alloy sheet mainly includes Cube and { 114}〈311〉 orientations, while the recrystallization texture of developed alloy sheet consists of Cube, Goss and R orientations. The relationships among the deep drawabilities, microstructure and texture were discussed thereafter.

Simultaneous enhancement of mechanical properties and corrosion resistance of as-cast Mg-5Zn via microstructural modification by friction stir processing

Magnesium alloys are ideal lightweight materials;however,their applications are extremely limited due to their low strength,poor ductility,and weak corrosion resistance.In the present study,a friction stir processing(FSP)treatment was employed to optimize the mechanical properties and corrosion resistance of an as-cast Mg-5Zn alloy.The average grain size of the Mg-5Zn alloy was refined from 133.8μm to1.3μm as a result of FSP.Along different directions,FSP exhibited the enhancement effects on different mechanical properties.Furthermore,according to the potentiodynamic polarization results,the corrosion current density at the free-corrosion potential of the FSPed sample,was 4.1×10^(-6)A/cm^(2)in 3.5 wt.%Na Cl aqueous solution,which was significantly lower than that of the as-cast sample.Electrochemical impedance spectroscopy revealed that the polarization impedance,Rp,of the FSPed sample was 1534Ω/cm^(2)in 3.5 wt.%NaCl aqueous solution,which was 71.4%greater than that of the as-cast sample.The corrosion morphology of the FSPed sample in 3.5 wt.%NaCl aqueous solution exhibited largely uniform corrosion,rather than severe localized corrosion characteristics,which further reduced the corrosion depth on the basis of reducing the corrosion current density.The results presented herein indicate that FSP is a viable technique for simultaneously improving the mechanical properties and corrosion resistance of the as-cast Mg-5Zn alloy.

Anisotropy of wrought magnesium alloys: A focused overview

In this paper, the relationship between anisotropic mechanical properties and the corresponding microstructure evolution of wrought magnesium alloys is critically reviewed. Experimental observations of the strong anisotropy(including the strength differential effect) induced by texture and twinning are discussed under different loading conditions(i.e., monotonic, cyclic and multiaxial loading). An accurate constitutive model is essential to describe the mechanical responses and to predict the forming performance considering engineering applications. Therefore, macroscale constitutive modeling of the anisotropy of magnesium alloys with directional distortional hardening are comprehensively reviewed with different approaches. To clarify the origin of the anisotropic behavior, physics-based mesoscale modeling of the anisotropy is also compared in detail.

A simplified approach to directly consider intact rock anisotropy in Hoek——Brown failure criterion

Many rock types have naturally occurring inherent anisotropic planes, such as bedding planes, foliation,or flow structures. Such characteristic induces directional features and anisotropy in rocks＇ strength anddeformational properties. The HoekeBrown （HeB） failure criterion is an empirical strength criterionwidely applied to rock mechanics and engineering. A direct modification to HeB failure criterion toaccount for rock anisotropy is considered as the base of the research. Such modification introduced a newdefinition of the anisotropy as direct parameter named the anisotropic parameter （Kb）. However, thecomputation of this parameter takes much experimental work and cannot be calculated in a simple way.The aim of this paper is to study the trend of the relation between the degree of anisotropy （Rc） and theminimum value of anisotropic parameter （Kmin）, and to predict the Kmin directly from the uniaxialcompression tests instead of triaxial tests, and also to decrease the amount of experimental work. 2014 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences. Production and hosting byElsevier B.V. All rights reserved.

Influence of anisotropy on the electrical conductivity and diffusion coefficient of dry K-feldspar： Implications of the mechanism of conduction

The electrical conductivities of single-crystal K-feldspar along three different crystallographic directions are investigated by the Solartron-1260 Impedance/Gain-phase analyzer at 873 K–1223 K and 1.0 GPa–3.0 GPa in a frequency range of 10-1 Hz–106 Hz. The measured electrical conductivity along the ⊥ [001] axis direction decreases with increasing pressure, and the activation energy and activation volume of charge carriers are determined to be 1.04 ± 0.06 e V and 2.51 ± 0.19 cm~3/mole, respectively. The electrical conductivity of K-feldspar is highly anisotropic, and its value along the⊥ [001] axis is approximately three times higher than that along the ⊥ [100] axis. At 2.0 GPa, the diffusion coefficient of ionic potassium is obtained from the electrical conductivity data using the Nernst–Einstein equation. The measured electrical conductivity and calculated diffusion coefficient of potassium suggest that the main conduction mechanism is of ionic conduction, therefore the dominant charge carrier is transferred between normal lattice potassium positions and adjacent interstitial sites along the thermally activated electric field.

On the texture evolution of Mg-Zn-Ca alloy with different hot rolling paths

In the present study,the texture evolution and mechanical anisotropy in a typical Mg–Zn–Ca alloy through hot cross rolling(CR)and unidirectional rolling(UR)were systematically studied.The results show that the rolling path greatly affects the annealed texture.The UR develops a texture with basal poles mainly distributing along the transverse direction(TD).By contrast,an ellipse-like(0002)texture with basal pole inclining largely away from the normal direction(ND)is developed after hot cross rolling and annealing.Therefore,the CR is an effective method to tailor the texture of the experimental alloy.Unfortunately,this ellipse-like texture could not reserve during the subsequent unidirectional hot rolling and annealing.Both UR and CR plates exhibit a strong planar mechanical anisotropy compared with the traditional unidirectional rolled plate.

Quantitative study on the tension-compression yield asymmetry of a Mg-3Al-1Zn alloy with bimodal texture components

This study demonstrates the yield asymmetry in Mg-3Al-1Zn alloy containing both ND-texture(c-axis//ND(Normal direction))and TD-texture(c-axis//TD(Transverse direction))in a quantitative view.The results showed that the yield asymmetry is strongly dependent on the distribution of bimodal texture components,on the basis of the successful establishment of the quantified relationship between pre-deformation parameters and texture components distribution.It’s meaningful for providing key reference to texture design.Mechanical behavior of bimodal textured Mg alloy under tension and compression was tested.CYS/TYS(compressive yield stress/tensile yield stress)equal to 1 is obtained,implying that the yield asymmetry is eliminated when two textures distribute at specific fractions.The corresponding mechanism for the texture-dependence of tension-compression yield asymmetry is revealed by the analysis of slip/twinning activities and a compound use of the activation stress difference of slip/twinning(ΔStress)and geometrical compatibility factor(m′)between neighboring grains.Balanced activity of{10■2}twinning and a quite similar boundary obstacle effect against slip/twinning transfer under tension and compression accounts for such good symmetry performance.

Mechanical and Corrosion Behavior of a Biomedical Mg–6Zn–0.5Zr Alloy Containing a Large Number of Twins

The strong texture of Mg alloys can lead to strong tension–compression yield asymmetry and corrosion anisotropy,and this will consequently affect the effectiveness of hard tissue implants.A biomedical Mg–6Zn–0.5Zr alloy containing a large number of{1012}primary twins and{1012}–{1012}secondary twins is successfully prepared by cross compression.The dual twin structure not only removes the tension–compression yield asymmetry completely,but effectively reduces the corrosion anisotropy without compromise of corrosion resistance.The difference between the largest corrosion rate and smallest one is~1.2 times compared to~1.6 times of the original materials.It is found that the reduced corrosion anisotropy is related to re-distribution of crystallographic orientations by twins.

Analysis of anisotropy mechanism in the mechanical property of titanium alloy tube formed through hot flow forming

Anisotropy of mechanical property is an important feature influencing the service performance of titanium(Ti)alloy tube component.In this work,it is found that the hot flow formed Ti alloy tube exhibits higher yield strength along circumferential direction(CD),and larger elongation along rolling direction(RD),presenting significant anisotropy.Subsequently,the quantitative characteristics and underlying mechanism of the property anisotropy were revealed by analyzing the slip,damage and fracture behavior under the combined effects of the spun{0002}basal texture and fibrous microstructure for different loading directions.The results showed that the prismatic slip in primaryαgrain is the dominant deformation mechanism for both loading directions at the yielding stage.The prismatic slip is harder under CD loading,which makes CD loading present higher yield strength than RD loading.Additionally,the yield anisotropy can be quantified through the inverse ratio of the averaged Schmid Factor of the activated prismatic slip under different loading directions.As for the plasticity anisotropy,the harder and slower slip development under CD loading causes that the CD loading presents larger external force and normal stress on slip plane,thus leading to more significant cleavage fracture than RD loading.Moreover,the micro-crack path under RD loading is more tortuous than CD loading because the fibrous microstructure is elongated along RD,which may suppress the macro fracture under RD loading.These results suggest that weakening the texture and fibrous morphology of microstructure is critical to reduce the differences in slip,damage and fracture behavior along different directions,alleviate the property anisotropy and optimize the service performance of Ti alloy tube formed by hot flow forming.

Functionally Graded Stainless Steel Fabricated by Direct Laser Deposition: Anisotropy of Mechanical Properties and Hardness

Direct laser metal deposition is a kind of advanced rapid manufacturing technology, which can produce near net shape parts by depositing metal powders layer by layer. This study demonstrates fabrication, the anisotropy of mechanical properties and hardness of a graded steel. The characteristics of constituent phases, microstructure, mechanical anisotropy, and microhardness were investigated using electron backscatter diffraction, optical microscopy, tensile test machine, and microhardness tester. It was found that the graded steel is dense and free of cracks. The crystal structures of the as-built samples evolved in three grades from fcc structures to fcc ＋ bcc structures and then to bcc ＋ fcc structures. Samples in x and z directions showed obvious mechanical anisotropy. The samples machined in x direction showed higher strength and lower elongation than those machined in z direction due to the presence of lack-of-fusion pores and the higher metallurgical bonding between layers in the x direction. The microhardness of the as-built samples increased along the cross section from the substrate （159.7 HV） to the top surface （545.4 HV）.

Insight into the formation mechanism and interaction of matrix/TiB whisker textures and their synergistic effect on property anisotropy in titanium matrix composites

Considerable studies on processed pure titanium and titanium alloys have proved the possibility of prop-erty anisotropy induced by crystallographic textures,but limited information is available for the intrinsic coupling of matrix and reinforcement textures and their synergistic effect on property anisotropy in tita-nium matrix composite(TMCs).In the present work,an advanced EBSD/EDS coupling method was used to investigate the formation mechanism of primaryαand secondaryαtextures in the matrix alloy.It is revealed for the first time that the reinforcement TiB_(w)displays a{100}<010>texture after hot rolling and has little effect on the matrix texture component but weakens texture intensity.Significant anisotropies in the tensile strength and ductility can be all noted at room and high-temperatures,which is the syn-ergistic effect of the matrix texture and the aligned TiB_(w).The mean Schmid factor of each slip system was calculated to evaluate the influence of matrix texture on the minimum active stress of slip deforma-tion in the different tensile directions.The analysis shows that the strong T-type matrix texture results in higher strength but lower ductility when loaded in the transverse direction.Moreover,a generalized shear-lag model was modified to quantitatively evaluate the strengthening contribution of aligned TiB_(w),which decreases with increasing off-axis angle and test temperature.A new parameter,defined as the critical aspect ratio of the off-axis whisker,was proposed to rationalize why the TiB_(w) failure mechanism converts from TiB_(w) fracture to TiB_(w)/matrix interfacial debonding with increasing off-axis angle and test temperature.

High Temperature Stress Rupture Anisotropy of a Ni-Based Single Crystal Superalloy

High temperature stress rupture anisotropies of a second generation Ni-base single crystal（SC） superalloy specimens with [001], [011] and [111] orientations under 900 ℃/445 MPa and 1100 ℃/100 MPa have been investigated in the present study, with attentions to the evolution of γ/γ′ microstructure observed by scanning electron microscopy and the dislocation configuration characterized by transmission electron microscopy in each oriented specimen. At 1100 ℃/100 MPa as well as 900 ℃/445 MPa, the single crystal superalloy exhibits obvious stress rupture anisotropic behavior. The [001] oriented specimen has the longest rupture lifetime at 900 ℃/445 MPa, and the [111] oriented sample shows the best rupture strength at 1100 ℃/100 MPa. While the [011] oriented specimen presents the worst rupture lifetime at each testing condition, its stress rupture property at 1100 ℃/100 MPa is clearly improved, compared with900 ℃/445 MPa. The evident stress rupture anisotropy at 900 ℃/445 MPa is mainly attributed to the distinctive movement way of dislocations in each oriented sample. Whereas, at 1100 ℃/100 MPa, together with the individual dislocation configuration, the evolution of γ/γ′ microstructure in each orientation also plays a key role in the apparent stress rupture anisotropy.

Effect of crushing methods on morphology and magnetic properties of anisotropic NdFeB powders

Crushing is a critical factor for the anisotropic Nd Fe B powders with high magnetic properties. However, the traditional crushing methods of disk-milling（DM） or impact crushing（IC）, are difficult to obtain high-performance powders. Herein, a new method of preparing anisotropic powders with high performance was reported, which was through crushing the hot-deformed magnets perpendicular to c-axis direction（shear crushing, SC）. The microstructure and alignment of the magnets were examined by scanning electron microscopy（SEM） and X-ray diffraction（XRD）, respectively. The results indicated that the cracks mainly extended along the Nd-rich grain boundary phase and/or the binding interface of ribbons. It not only could protect the magnetic phase from being damaged, but also could keep the grains integrated. Therefore, shear crushing was an effective method for the preparation of highperformance anisotropic powders and then to fabricate the bonded magnets with Br=9.0 kGs, Hci=10.48 kOe and（BH）max=17.7 MGOe.