The Influence of Carbon Nanotubes and Nano-Silica Fume on Enhancing the Damping and Mechanical Properties of Cement-Based Materials

This paper conducted experimental studies on the damping and mechanical properties of carbon nanotube-nanosilica-cement composite materials with different carbon nanotube contents. The damping and mechanical properties enhancement mechanisms were analyzed and compared through the porosity structure test, XRD analysis, and scanning electron microscope observation. The results show that the introduction of nanosilica significantly improves the dispersion of carbon nanotubes in the cement matrix. At the same time, the addition of nanosilica not only effectively reduces the critical pore size and average pore size of the cement composite material, but also exhibits good synergistic effects with carbon nanotubes, which can significantly optimize the pore structure. Finally, a rationalization suggestion for the co-doping of nanosilica and carbon nanotubes was given to achieve a significant increase in the flexural strength, compressive strength and loss factor of cement-based materials.

Optimization on microstructure,mechanical properties and damping capacities of duplex structured Mg–8Li–4Zn–1Mn alloys

Optimizing the mechanical properties and damping capacity of the duplex-structured Mg–Li–Zn–Mn alloy by tailoring the microstructure via hot extrusion was investigated.The results show that the Mg–8Li–4Zn–1Mn alloy is mainly composed ofα-Mg,β-Li,Mg–Li–Zn and Mn phases.The microstructure of the test alloy is refined owing to dynamic recrystallization(DRX)during hot extrusion.After hot extrusion,the crushed precipitates are uniformly distributed in the test alloy.The yield strength(YS),ultimate tensile strength(UTS),and elongation(EL)of as-extruded alloy reach 156 MPa,208 MPa,and 32.3%,respectively,which are much better than that of as-cast alloy.Furthermore,the as-extruded and as-cast alloys both exhibit superior damping capacities,with the damping capacity(Q^(-1))of 0.030 and 0.033 at the strain amplitude of 2×10^(-3),respectively.The mechanical properties of the test alloy can be significantly improved by hot extrusion,whereas the damping capacities have no noticeable change,which indicates that the duplex-structured Mg–Li alloys with appropriate mechanical properties and damping properties can be obtained by alloying and hot extrusion.

Effects of Y on mechanical properties and damping capacity of ZK60 magnesium alloys

The microstructure,mechanical properties and damping capacity of ZK60-xY(x=0,1.5%,2.5%,4.0%,mass fraction) magnesium alloys were investigated by using the optical microscope(OM),X-ray diffractometer(XRD),universal tensile testing machine and dynamic mechanical analyzer(DMA).The mechanisms for damping capacity of referred alloys were discussed by Granato-Lücke theory.The results show that Y additions remarkably reduce grain size(the average grain size is 21.6,13.0,8.6 and 4.0μm,respectively),and the tensile properties are enhanced with grain refining(the yield tensile strength increases to 292 MPa from 210 MPa and ultimate tensile strength increases to 330 MPa from 315 MPa).For the ZK60-xY(x=0,1.5%,4.0%)alloys,the damping capacity decreases with the increase of Y content.However,for the ZK60-xY(x=2.5%)alloy,the damping capacity improves abnormally,which is possibly related to the formation of Mg3Y2Zn3(W)FCC phase in this alloy.

Effects of Cu and Mn on mechanical properties and damping capacity of Mg-Cu-Mn alloy

The effects of Cu and Mn additions on mechanical properties and damping capacity of Mg-Cu-Mn alloy were investigated. The tensile properties and damping capacity at room temperature of as-cast Mg-Cu-Mn alloy were tested.The microstructurc was studied using optical microscope,X-ray diffraction and scanning electron microscope.The Hall-Perch relation and Granato-Lücke model were used to explain the influences of Cu and Mn additions on the tensile properties and damping capacity of Mg-Cu-Mn alloy.The results show that Cu and Mn additions remarkably reduce the grain size of Mg-Cu-Mn alloy,but have little influence on phase composition and solute atoms concentration,the tensile properties increase obviously and the internal friction of Mg-Cu-Mn alloy decreases with grain refining.

The transformation of LPSO type in Mg-4Y-2Er-2Zn-0.6Zr and its response to the mechanical properties and damping capacities

The transformation of LPSO type in Mg-4Y-2Er-2Zn-0.6Zr during heat treatment and its influence on damping and mechanical properties are reported in this work.Prior to heat treatment,the alloy consisted of a-Mg matrix and lamellar 14H LPSO phases.After 510℃heat treatment,lamellae shortened,and their content decreased.Upon 8h heat treatment,block 18R LPSO phases formed at the grain boundaries while 14H LPSO lamellae disappeared.Presence of block 18R LPSO phases improved mechanical and damping properties of the alloy.The corresponding mechanisms of the influence of LPSO type and morphology on mechanical and damping capacities are discussed.

Damping and Mechanical Properties of Cocured Composite Laminates with Embedded Perforate Viscoelastic Layer

The composite laminates with embedded acrylonitrile butadiene rubber （NBR） layer were fabricated by cocuring process. The embedded layers were perforated with a series of small holes to allow resin to flow through the damping layer and completely couple the structure to improve bending stiffness and interlaminar shearing strength of these cocured composite laminates. The damping, bending stiffness and shearing strength of these composite laminates with different perforation diameters were investigated. The experimental results show that increasing the perforation diameter leads to significant decreases in damping and significant increase in bending stiffness up to an area ratio of 7.065%. The area ratio here is defined as the ratio of perforation area to the total damping area. Beyond the area ratio of 7.065%, increasing the diameter to an area ratio of 50.24% results in only a slight variation in damping and bending stiffness. Moreover, increasing the perforation diameter does not always increase the shearing strength of the embedded viscoelastic layer. The shearing strength of embedded viscoelastic layer increases only when the area ratio is greater than 19.625%; instead, it will decrease.

Optimization of mechanical and damping properties of Mg-0.6Zr alloy by different extrusion processing

In this study,the optimization of mechanical and damping capacities of Mg-0.6 wt.%Zr alloys by controlling the recrystallized(DRXed)grain size under varying extrusion processing parameters including extrusion temperature T and strain rate was investigated.The relationship between the DRXed grain size and damping properties of the studied alloy was also discussed.The DRXed grain size of the as-extruded Mg-Zr alloys decreased as the extrusion temperature T decreased and the strain rateεincreased.As the DRXed grain size decreased,the strength and elongation of the as-extruded alloys exhibited improved performance through the grain refinement mechanism,while the damping properties deteriorated.The extrusion temperature of the Mg-Zr alloy had relatively greater effects on the mechanical and damping properties than the strain rate.The results of the present work indicate that alloys with appropriate mechanical and damping properties may be obtained from controlling the DRXed grain size by careful tailoring of the extrusion process parameters.

Design and preparation of Zn-based materials possessing both high damping and good mechanical properties

A new idea of design and manufacture of metal based materials possessing both high damping and good mechanical properties was proposed. The key of the idea is the combination of fining restriction damping structures, using all mechanisms and taking advantages of different materials. Based upon this idea a foam ZA27 was prepared by the technology of prefabricated salt mass centrifugal seeping foundry, its tensile strength and compressive strength are 83～119?MPa and 100～189?MPa, respectively. The damping properties of the foam ZA27 increase remarkably after the carpenter pastern or rosin (the damping increased materials) was immerged into it, which approaches to the level of viscous elastic polymer materials ( Q -1 ≥20×10 -3 ). [

Damping behavior and mechanical properties of Mg-Cu-Mn alloy processed by equal channel angular pressing

Equal channel angular pressing(ECAP) was conducted at 250℃for 4 passes to the as-extruded Mg-3%Cu-1%Mn alloy with high strength and high damping capacity.After ECAP processing,the grain of as-extruded alloy is significantly refined to about 4μm,both yield strength and tensile strength of the as-extruded Mg-Cu-Mn alloy are decreased,but the ductility is improved.After the ECAP processing,the damping capacity of Mg-Cu-Mn alloy is decreased at room temperature,while is substantially increased at elevated temperatures,After annealing at 300℃for 1 h,both yield strength and tensile strength of the ECAPed alloy are further decreased,but the ductility is significantly improved.The damping capacity of the as-annealed alloy is increased at room temperature, while is decreased at elevated temperatures.The mechanisms for damping capacity of the alloy at ambient and elevated temperatures were discussed.

Effect of eutectic phase on damping and mechanical properties of as-cast Mg-Ni hypoeutectic alloys

Dynamic mechanical analysis (DMA) was applied to systematically investigate the low frequency damping properties of as-cast hypoeutectic Mg-Ni alloys. The results show that the as-cast hypoeutectic Mg-Ni alloys exhibit high damping capacities. The strain amplitude dependent damping curve has its own special characteristic, in which the damping is strongly related to the strain amplitude. The effect of the eutectic phase on damping and the mechanical properties of as-cast hypoeutectic Mg-Ni alloys were also discussed in detail.

Effect of Stacking Sequences on the Mechanical and Damping Properties of Flax Glass Fiber Hybrid

The aim of this study is to show the interest of the mechanical and dynamical properties of glass-flax hybrid composites.Therefore,various staking sequences of glass-flax hybrid composites were manufactured and tested in free vibrations.The damping coefficients were identified by fitting the experimental responses of free-free bending vibrations.The obtained results show that the staking sequences and the position of flax fiber layers in the hybrid composites changed the properties,so a classification of different stacking sequences was established.In fact,the hybrid laminate made of two glass external layers placed on both sides of four flax layers is very interesting in term of its mechanical and damping properties.Indeed,it showed better specific bending modulus and loss factor than glass composites with proportions of 31 and 39%,respectively.A study of a structure of this composite has been made to validate the obtained results.

Mechanism of improving strength and damping properties of powder-extruded Al/Zn composite after diffusion annealing

In order to develop high strength,high damping and low density Al matrix composites,the Al/Zn composite bar samples with Zn mass fraction of 10%-40%were prepared by powder extrusion.The tensile strength and damping properties of the samples are improved by controlling both the Zn/Al diffusion degree and the precipitation of the interfacial phases.The results show that the tensile strength of the samples with Zn mass fraction of 10%-30%increases with the increases of both the Zn content and annealing temperature.When the Zn mass fraction increases to 40%,the tensile strength of the sample remains basically unchanged or decreases slightly,and the plasticity decreases gradually.Alloying of Al matrix and the formation of Zn/Al interface layer are mainly responsible for improving the strength of the annealed samples.The damping properties increase with the increases of both the Zn content and annealing temperature.The Zn/Al eutectoid lamella eliminates the detrimental effects on damping properties due to both alloying of the Al matrix and reduction of pure Zn in the Al matrix.The Al-30%Zn sample annealed at 350°C for 0.5 h has good comprehensive properties,including the tensile strength of 330 MPa,the elongation to failure of 10%and the room-temperature damping properties(tanθ)of 0.025.

Mechanical properties of monodirectional Gutou mortise-tenon joints of the traditional timber buildings in the Yangtze River region

The mechanical properties of the monodirectional Gutou mortise-tenon joints of the ancient Chinese traditional timber buildings in the Yangtze River region were studied using the experimental method. Three monodirectional Gutou mortise-tenon joints were designed according to the actual configurations. The failure modes,the hysteretic curves,the skeleton curves, the rotation rigidities, and the energy dissipation capacity of this type of mortise-tenon joints under the low cyclic reversed loading were obtained. The results show that the hysteretic curves of the monodirectional Gutou mortise-tenon joints appear to be Z shape and have obvious pinch effects. During the process of the test,these mortisetenon joints pass orderly through the elastic stage,the yield stage and the failure stage. The energy dissipation capacity of these mortise-tenon joints generally decreases with the increase in the rotation angle. The equivalent viscous damping coefficients of the monodirectional Gutou mortise-tenon joints are between 0. 161 and 0. 193. The results can provide the theoretical base for the computing analysis and repair design of Chinese traditional timber buildings in the Yangtze River region.

Damping capacity of BaTiO_3/Al composites fabricated by hot extrusion

To develop new type of high damping metal matrix composites, large grain size barium titanate （BaTiO3） ceramic was sintered and added into Al powder to fabricate BaTiO3/Al composites through the powder metallurgy method and hot extrusion. The damping properties of BaTiO3 ceramic, Al matrix and BaTiO3/Al composites were examined by dynamic mechanical analysis in the temperature range from 273 K to 573 K. The results show that although BaTiO3 exhibits high damping （tan δ=0.12） below 400 K, the damping capacity of 10%BaTiO3/Al （mass fraction） composites below 400 K is not increased as compared to the Al matrix. On the other hand, the damping capacity above 450 K is greatly enhanced due to the motion of dislocations at the interfaces between ceramic particles and Al matrix. The failure of exerting the intrinsic damping of BaTiO3 particles in the composites is attributed to the poor interface bonding between the particles and the matrix. The tensile strength of the composite is 42% higher than that of the Al matrix, which indicates the possibility of obtaining high strength and high damping composites via interface improvement and the addition of high volume fraction of large grain BaTiO3 particles.

Damping capacity of high strength-damping aluminum alloys prepared by rapid solidification and powder metallurgy process

Two kinds of high strength-damping aluminum alloys （LZ7） were fabricated by rapid solidification and powder metallurgy （RS-PM） process. One material was extruded to profile aluminum directly and the other was extruded to bar and then rolled to sheet. The damping capacity over a temperature range of 25-300 ℃was studied with damping mechanical thermal analyzer （DMTA） and the microstructures were investigated by optical microscopy （OM）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The experimental results show that the damping capacity increases with the test temperature elevating. Internal friction value of rolled sheet aluminum is up to 11.5×10^-2 and that of profile aluminum is as high as 6.0×10^-2 and 7.5×10^-2 at 300 ℃, respectively. Microstructure analysis shows the shape of precipitation phase of rolled alloy is more regular and the distribution is more homogeneous than that of profile alloy. Meanwhile, the interface between particulate and matrix of rolled sheet alloy is looser than that of profile alloy. Maybe the differences at interface can explain why damping capacity of rolled sheet alloy is higher than that of profile alloys at high temperature （above 120 ℃）.

Design optimization of cast Cu-Al-Be-B alloys for high damping capacity

This paper investigated high-damping Cu-Al-Be-B cast alloys using metallographic analysis, X-ray diffraction (XRD) and electrical resistance measurements for transformation temperatures. The results showed that beryllium can stabilize β phase, resulting in a thermo-elastic martensite microstructure leading to high-damping capacity in cast Cu-Al-Be-B alloys. Trace additions of boron to Cu-Al-Be alloys can significantly refine the grains, providing high strength and ductility to the alloys. A factorial design of experiment method was used to optimize the composition and properties of cast Cu-Al-Be-B alloys. The optimal microstructure for thermo-elastic martensite can be obtained by adjusting the amounts of aluminum and beryllium to eutectoid or pseudo-eutectoid compositions. An optimized cast Cu-Al-Be-B alloy was developed to provide excellent mechanical properties, tensile strength σ_b=767MPa, elongation δ=7.62%, and damping capacity S. D. C=18.70%.

INFLUENCE OF Al-5Ti-1B MASTER ALLOY ON MICROSTRUCTURE AND DAMPING CAPACITY OF ZA27 ALLOY

１ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｄａｍｐｉｎｇｃａｐａｃｉｔｙｏｆａｍａｔｅｒｉａｌｉｓａｍｅａｓｕｒｅｏｆｔｈｅｅｎｅｒｇｙｔｈａｔｉｓｄｉｓｓｉｐａｔｅｄｉｎｔｈｅｍａｔｅｒｉａｌｄｕｒｉｎｇｍｅｃｈａｎｉｃａｌｖｉｂｒａｔｉｏｎｕｎｄｅｒｃｙｃ...

Influence of RE Content on Damping Capacity of Alloy ZA27

The modification mechanism and damping capacity(Q-1) of conventional ascast ZA27 alloy modified by Al10%RE were investigated. Cantilever beam technique was used to measure the damping capacity. The experimental results show that the addition of RE to the ZA27 alloy can refine microstructure and improve the damping capacity, the best modification effect and the highest damping capacity can be obtained at 03%RE content. It is believed that the damping mechanism of ZA27 alloy is associated with the viscous sliding or slipping of grain boundaries and interfaces, and the more the grain boundaries and interfaces, the higher the damping capacity of ZA27 alloy can be obtained.

Effects of Ce on damping capacity of AZ91D magnesium alloy

The microstructures and damping capacity of AZ91D cast alloys containing various Ce contents were investigated. Damping capacity (Q-1) of the alloys was measured by cantilever beam technique, and the relationship between damping capacity and strain amplitude was investigated. The results show that Al4Ce phase is formed in AZ91D alloy after adding a certain quantity of Ce contents, then as-cast microstructures of the alloys are refined. Meanwhile the damping capacity of the alloys is also improved. When the mass fraction of Ce is 0.7%, the most obvious refinement effect and the maximum damping capacity can be obtained. When the damping capacity (Q-1) is )2.728)×10-3, 61% increment can be obtained compared with unmodified AZ91D alloy. The damping capacity of the alloys is relative to strain amplitude, and the damping behavior can be explained by the theory of Granato and Lücke.

Solidification microstructure evolution and its correlations with mechanical properties and damping capacities of Mg-Al-based alloy fabricated using wire and arc additive manufacturing

Magnesium(Mg)alloys,as the lightest metal structural material with good damping capacities,have im-portant application prospects in realizing structural lightweight and vibration reduction.However,their engineering application is greatly limited by poor plastic formability.Wire and arc additive manufactur-ing(WAAM)provides a potential approach for fabricating large-scale Mg alloy components with high manufacturing flexibility.In this study,the evolution of the solidification microstructure of a WAAM-processed Mg-Al-based alloy was quantitatively analyzed based on the analytical models;then,the cor-relations between the solidification microstructure and mechanical properties/damping capacities were investigated.The results revealed that the WAAM-processed Mg-Al-based alloy with an equiaxed-grain-dominated microstructure displayed a simultaneous enhancement in mechanical properties and damping capacities compared to those of the cast Mg-Al-based alloy.The good combination of mechanical prop-erties and damping capacities are mainly attributed to the weakened basal texture with a relatively high Schmid factor for basalslip,the twinning-induced plasticity(TWIP)effect associated with the profuse{10-12}tensile twinning,and the relatively high dislocation density caused by the thermal stress during the WAAM process.