Based on the instantaneous pressurization and depressurization produced by high pressure single pole cylinder pump and valve, the effects of the continuous processing on the peroxidase (POD) activity in wax gourd ju...Based on the instantaneous pressurization and depressurization produced by high pressure single pole cylinder pump and valve, the effects of the continuous processing on the peroxidase (POD) activity in wax gourd juices were investigated. Results showed that the processing factors such as pressure, temperature, pH and processing time are important to the POD activity. POD in crude juices could be inactivated apparently above 50 MPa(pH 4.6, 35℃, 4 min), and activated at 20 MPa ( P < 0.01). Its remarkable inactivation could also be observed at 45 and 55℃ (20 MPa, pH 4.6, 4 min), and the evident activation appears at the material temperature 35℃ ( P < 0.01). The pH 3.0 could destroy POD almost completely (20 MPa, 35℃, 4 min), while pH 6.0 could not influence apparently the POD activity in crude juices( P > 0.05). In addition, the rules of POD activity along with the treatment time are variational under different processing pressures. The higher the treating pressure is, the shorter the processing time is needed to inactivate POD.展开更多
Based on the instantaneous high-pressure(IHP)produced by high-pressure single pole-cylinder pump, the effects of combining this pressure with medium temperature on the retention of total vitamin C(Vc)in wax gourd juic...Based on the instantaneous high-pressure(IHP)produced by high-pressure single pole-cylinder pump, the effects of combining this pressure with medium temperature on the retention of total vitamin C(Vc)in wax gourd juices were investigated under 20 - 80 MPa, 35 - 58℃, pH 3. 0 - 6. 0 and processing time 0-8 min. Results showed that the loss of Vc increased with elevated processing temperatures(50 MPa, 4 min). When the temperature of raw juices was 35℃, the retention of total Vc was higher under 40 - 60 MPa than that under the pressure < 40 MPa or > 60 MPa, and it was up to 94%(4 min). The retention of total Vc decreases slowly within 6 min, but rapidly after 6 min. The pH can also influence the retention of total Vc, and this retention can come to a highest point at pH 6.0.展开更多
The production of environment friendly green fuels is based on energy from renewable sources. Among the renewable sources, wind power is a very growing power technology. An example which has been discussed very widely...The production of environment friendly green fuels is based on energy from renewable sources. Among the renewable sources, wind power is a very growing power technology. An example which has been discussed very widely is hydrogen which is an ideal fuel for a fuel cell. Hydrogen is the energy of the future. It will be used as energy carrier as well as reactant to produce green fuels, like methane which is easier to handle. Direct coupling of a High Temperature Steam Electrolyser (HTSE) with a wind turbine can be used to generate hydrogen. Indeed performing the electrolysis process at high temperatures offers the advantage of achieving higher efficiencies compared to the conventional water electrolysis. The hydrogen produced can be then reacted with the CO2 content of biogas to form methane as green fuel. Thus, the concept presented in this paper illustrates the potential of the HTSE technology coupled with a wind turbine, this system being combined with biogas in a methanation unit. Developing scenarios and flow sheets and using mass and energy balance, the technical performance of the concept is investigated. A plant capacity of 10 MWel is considered. An annual production of 1104 metric tons per year (Mt/a) hydrogen and thus of 5888 Mt/a methane is reached. The overall plant efficiency is calculated to be 38%. The combination of wind power and biogas offers thus many advantages which can facilitate the penetration of the wind resource and the progression to the hydrogen economy.展开更多
The transformation of the energy supply needs further development of energy storage technologies in order to integrate the fluctuating renewable energy. The conversion of renewable wind power into green methane offers...The transformation of the energy supply needs further development of energy storage technologies in order to integrate the fluctuating renewable energy. The conversion of renewable wind power into green methane offers a technical approach with the necessary storage and transport capacities. Thus, the concept of Power-to-Gas which is illustrated here by the coupling of wind energy with a High Temperature Steam Electrolyser (HTSE) and a methanation unit enabling the production of green fuel like hydrogen and methane is presented is this paper. In fact, hydrogen can be used as energy carrier as well for the production of green fuels, like methane which is simpler to store and to transport and which can be thus used as storage medium for the stabilization of the electrical power supply as well as fuel for transport and heat sector. Its production using high temperature electrolysis is able to reduce the carbon dioxide emissions if performed with renewable resources. This is the case if the electricity needed for the HTSE comes from a wind turbine and the CO2 needed for the methanation step comes from biogas. For such a plant, the location and the boundary conditions have a great importance. Thus, this study considers the coupling of a HTSE with a wind turbine and a methanation reactor, and focuses about the site selection, depending of the geographical and economic considerations. The study is limited first to the European area. Schleswig-Holstein is found as a very good location for this plant. It is one of the regions with the largest wind reserves in Germany. This region has also available a lot of biogas and meets all the other necessary requirements.展开更多
Oxidation characteristics of Alloy 617 and Haynes 230 at 900 oC in simulated helium environment,hot steam environment containing H2 as well as in air and pure helium conditions were investigated.Compared to air condit...Oxidation characteristics of Alloy 617 and Haynes 230 at 900 oC in simulated helium environment,hot steam environment containing H2 as well as in air and pure helium conditions were investigated.Compared to air condition,the oxidation rate of Alloy 617 was not significantly affected in helium and hot steam environments,while Haynes 230 showed lower oxidation rate in helium environment.On the other hand,the oxide morphology and structure of Alloy 617 were strongly affected by the environments,but those of Haynes 230 were less dependent on the environments.For Haynes 230,a Cr2O3 inner layer and a protective MnCr2O4 outer layer were formed in all environments,which contributed to the better oxidation resistance.As the mechanical properties,such as creep and tensile properties,were significantly affected by the oxidation behaviors,surface treatment methods to enhance oxidation resistance of these alloys should be developed.展开更多
This work proposes a novel tubular structure of high-temperature proton exchange membrane fuel cell(PEMFC)integrated with a built-in packed-bed methanol steam reformer to provide hydrogen for power output.A two-dimens...This work proposes a novel tubular structure of high-temperature proton exchange membrane fuel cell(PEMFC)integrated with a built-in packed-bed methanol steam reformer to provide hydrogen for power output.A two-dimensional axisymmetric non-isothermal model was developed in COMSOL Multiphysics 5.4 to simulate the performance of a tubular high temperature proton membrane fuel cell and a packed bed methanol reformer.The model considers the coupling multi-physical processes,including methanol reforming reaction,water gas shift reaction,methanol cracking reaction as well as the heat,mass and momentum transport processes.The sub-model of the tubular packed-bed methanol reformer is validated between 433 K and 493 K with the experimental data reported in the literature.The sub-model of the high temperature proton exchange fuel cell is validated between 393 K and 433 K with the published literature.Our results show that power output and temperature distribution of the integrated unit depend on methanol flow rates and working voltages.It was suggested that stable power generation performance of 0.14 W/cm_(2)and temperature drop in methanol steam reformer of≤10 K could be achieved by controlling the methanol space-time ratio of≥250 kg·s/mol with working voltage at 0.6 V,even in the absence of an external heat source.展开更多
为明确山东临沂和河南周口地区中高温大曲细菌群落结构及菌群基因功能的差异,本研究采用MiSeq高通量测序技术对2个地区中高温大曲的细菌群落结构进行了解析,并基于直系同源蛋白数据库(clusters of orthologous groups of proteins,COG)...为明确山东临沂和河南周口地区中高温大曲细菌群落结构及菌群基因功能的差异,本研究采用MiSeq高通量测序技术对2个地区中高温大曲的细菌群落结构进行了解析,并基于直系同源蛋白数据库(clusters of orthologous groups of proteins,COG)分析了其细菌类群潜在的功能。α多样性发现,两者在丰富度和多样性上差异均不显著(P>0.05)。相较于周口地区大曲,在门水平上,临沂地区大曲中放线菌门(Actinobacteria)和拟杆菌门(Bacteroidetes)平均相对丰度均显著偏低(P<0.05),在属水平上,不动杆菌属(Acinetobacter)平均相对丰度显著偏高(P<0.05),地杆菌属(Geobacter)和泛菌属(Pantoea)平均相对丰度均显著偏低(P<0.05)。LEfSe(linear discriminant analysis effect size)分析发现,Geobacter为周口地区大曲中的生物标志物,而临沂地区大曲中的生物标志物未在属水平体现;β多样性发现,两者在整体上存在明显差异;PICRUSt(phylogenetic investigation of communities by reconstruction of unobserved states)分析发现,临沂地区中高温大曲在转录、氨基酸和核苷转运与代谢功能上显著高于周口地区大曲(P<0.05)。由此可见,2个地区中高温大曲的细菌群落结构及菌群基因功能表达均存在明显差异。展开更多
文摘Based on the instantaneous pressurization and depressurization produced by high pressure single pole cylinder pump and valve, the effects of the continuous processing on the peroxidase (POD) activity in wax gourd juices were investigated. Results showed that the processing factors such as pressure, temperature, pH and processing time are important to the POD activity. POD in crude juices could be inactivated apparently above 50 MPa(pH 4.6, 35℃, 4 min), and activated at 20 MPa ( P < 0.01). Its remarkable inactivation could also be observed at 45 and 55℃ (20 MPa, pH 4.6, 4 min), and the evident activation appears at the material temperature 35℃ ( P < 0.01). The pH 3.0 could destroy POD almost completely (20 MPa, 35℃, 4 min), while pH 6.0 could not influence apparently the POD activity in crude juices( P > 0.05). In addition, the rules of POD activity along with the treatment time are variational under different processing pressures. The higher the treating pressure is, the shorter the processing time is needed to inactivate POD.
文摘Based on the instantaneous high-pressure(IHP)produced by high-pressure single pole-cylinder pump, the effects of combining this pressure with medium temperature on the retention of total vitamin C(Vc)in wax gourd juices were investigated under 20 - 80 MPa, 35 - 58℃, pH 3. 0 - 6. 0 and processing time 0-8 min. Results showed that the loss of Vc increased with elevated processing temperatures(50 MPa, 4 min). When the temperature of raw juices was 35℃, the retention of total Vc was higher under 40 - 60 MPa than that under the pressure < 40 MPa or > 60 MPa, and it was up to 94%(4 min). The retention of total Vc decreases slowly within 6 min, but rapidly after 6 min. The pH can also influence the retention of total Vc, and this retention can come to a highest point at pH 6.0.
文摘The production of environment friendly green fuels is based on energy from renewable sources. Among the renewable sources, wind power is a very growing power technology. An example which has been discussed very widely is hydrogen which is an ideal fuel for a fuel cell. Hydrogen is the energy of the future. It will be used as energy carrier as well as reactant to produce green fuels, like methane which is easier to handle. Direct coupling of a High Temperature Steam Electrolyser (HTSE) with a wind turbine can be used to generate hydrogen. Indeed performing the electrolysis process at high temperatures offers the advantage of achieving higher efficiencies compared to the conventional water electrolysis. The hydrogen produced can be then reacted with the CO2 content of biogas to form methane as green fuel. Thus, the concept presented in this paper illustrates the potential of the HTSE technology coupled with a wind turbine, this system being combined with biogas in a methanation unit. Developing scenarios and flow sheets and using mass and energy balance, the technical performance of the concept is investigated. A plant capacity of 10 MWel is considered. An annual production of 1104 metric tons per year (Mt/a) hydrogen and thus of 5888 Mt/a methane is reached. The overall plant efficiency is calculated to be 38%. The combination of wind power and biogas offers thus many advantages which can facilitate the penetration of the wind resource and the progression to the hydrogen economy.
文摘The transformation of the energy supply needs further development of energy storage technologies in order to integrate the fluctuating renewable energy. The conversion of renewable wind power into green methane offers a technical approach with the necessary storage and transport capacities. Thus, the concept of Power-to-Gas which is illustrated here by the coupling of wind energy with a High Temperature Steam Electrolyser (HTSE) and a methanation unit enabling the production of green fuel like hydrogen and methane is presented is this paper. In fact, hydrogen can be used as energy carrier as well for the production of green fuels, like methane which is simpler to store and to transport and which can be thus used as storage medium for the stabilization of the electrical power supply as well as fuel for transport and heat sector. Its production using high temperature electrolysis is able to reduce the carbon dioxide emissions if performed with renewable resources. This is the case if the electricity needed for the HTSE comes from a wind turbine and the CO2 needed for the methanation step comes from biogas. For such a plant, the location and the boundary conditions have a great importance. Thus, this study considers the coupling of a HTSE with a wind turbine and a methanation reactor, and focuses about the site selection, depending of the geographical and economic considerations. The study is limited first to the European area. Schleswig-Holstein is found as a very good location for this plant. It is one of the regions with the largest wind reserves in Germany. This region has also available a lot of biogas and meets all the other necessary requirements.
基金supported by the MEST/NRF (Nuclear R&D Program,2005-2004718 and 2009 0083392) of Korea
文摘Oxidation characteristics of Alloy 617 and Haynes 230 at 900 oC in simulated helium environment,hot steam environment containing H2 as well as in air and pure helium conditions were investigated.Compared to air condition,the oxidation rate of Alloy 617 was not significantly affected in helium and hot steam environments,while Haynes 230 showed lower oxidation rate in helium environment.On the other hand,the oxide morphology and structure of Alloy 617 were strongly affected by the environments,but those of Haynes 230 were less dependent on the environments.For Haynes 230,a Cr2O3 inner layer and a protective MnCr2O4 outer layer were formed in all environments,which contributed to the better oxidation resistance.As the mechanical properties,such as creep and tensile properties,were significantly affected by the oxidation behaviors,surface treatment methods to enhance oxidation resistance of these alloys should be developed.
文摘This work proposes a novel tubular structure of high-temperature proton exchange membrane fuel cell(PEMFC)integrated with a built-in packed-bed methanol steam reformer to provide hydrogen for power output.A two-dimensional axisymmetric non-isothermal model was developed in COMSOL Multiphysics 5.4 to simulate the performance of a tubular high temperature proton membrane fuel cell and a packed bed methanol reformer.The model considers the coupling multi-physical processes,including methanol reforming reaction,water gas shift reaction,methanol cracking reaction as well as the heat,mass and momentum transport processes.The sub-model of the tubular packed-bed methanol reformer is validated between 433 K and 493 K with the experimental data reported in the literature.The sub-model of the high temperature proton exchange fuel cell is validated between 393 K and 433 K with the published literature.Our results show that power output and temperature distribution of the integrated unit depend on methanol flow rates and working voltages.It was suggested that stable power generation performance of 0.14 W/cm_(2)and temperature drop in methanol steam reformer of≤10 K could be achieved by controlling the methanol space-time ratio of≥250 kg·s/mol with working voltage at 0.6 V,even in the absence of an external heat source.
文摘为明确山东临沂和河南周口地区中高温大曲细菌群落结构及菌群基因功能的差异,本研究采用MiSeq高通量测序技术对2个地区中高温大曲的细菌群落结构进行了解析,并基于直系同源蛋白数据库(clusters of orthologous groups of proteins,COG)分析了其细菌类群潜在的功能。α多样性发现,两者在丰富度和多样性上差异均不显著(P>0.05)。相较于周口地区大曲,在门水平上,临沂地区大曲中放线菌门(Actinobacteria)和拟杆菌门(Bacteroidetes)平均相对丰度均显著偏低(P<0.05),在属水平上,不动杆菌属(Acinetobacter)平均相对丰度显著偏高(P<0.05),地杆菌属(Geobacter)和泛菌属(Pantoea)平均相对丰度均显著偏低(P<0.05)。LEfSe(linear discriminant analysis effect size)分析发现,Geobacter为周口地区大曲中的生物标志物,而临沂地区大曲中的生物标志物未在属水平体现;β多样性发现,两者在整体上存在明显差异;PICRUSt(phylogenetic investigation of communities by reconstruction of unobserved states)分析发现,临沂地区中高温大曲在转录、氨基酸和核苷转运与代谢功能上显著高于周口地区大曲(P<0.05)。由此可见,2个地区中高温大曲的细菌群落结构及菌群基因功能表达均存在明显差异。
