A set of compressed natural gas (CNG) multi-point direct injection system of spark-ignited engines and the corresponding measurement and data acquisition systems were developed in this paper. Based on different inject...A set of compressed natural gas (CNG) multi-point direct injection system of spark-ignited engines and the corresponding measurement and data acquisition systems were developed in this paper. Based on different injection modes, the mixture formation and combustion of CNG low-pressure direct injection (LPDI) engines were studied under varying factors such as air/ fuel ratio, injection timing. Meanwhile, three-dimensional simulations were adopted to explain the mixture formation mechanisms of CNG low-pressure compound direct injection (LPCDI) mode. On the basis of test results and simulation of the mixture homogeneous degree, the conception of injection window was proposed, and the LPCDI mode was proved to be more beneficial to the mixture concentration stratification formation in cylinder under lean-burning conditions, which resulted in effective combustion and stability.展开更多
A rotor dynamic model is built up for investigating the effects of tightening torque on dynamic characteristics of low pressure rotors connected by a spline coupling.The experimental rotor system is established using ...A rotor dynamic model is built up for investigating the effects of tightening torque on dynamic characteristics of low pressure rotors connected by a spline coupling.The experimental rotor system is established using a fluted disk and a speed sensor which is applied in an actual aero engine for speed measurement.Through simulating calculation and experiments,the effects of tightening torque on the dynamic characteristics of the rotor system connected by a spline coupling including critical speeds,vibration modes and unbalance responses are analyzed.The results show that when increasing the tightening torque,the first two critical speeds and the amplitudes of unbalance response gradually increase in varying degrees while the vibration modes are essentially unchanged.In addition,changing axial and circumferential positions of the mass unbalance can lead to various amplitudes of unbalance response and even the rates of change.展开更多
Objective The goal of this study was to develop a decellularized tendon scaffold(DTS)and repopulate it with adipose-derived stem cells(ADSCs)assisted by low air pressure(LP).Methods The porcine superficial flexor tend...Objective The goal of this study was to develop a decellularized tendon scaffold(DTS)and repopulate it with adipose-derived stem cells(ADSCs)assisted by low air pressure(LP).Methods The porcine superficial flexor tendons were processed into the DTSs using a combination of physical,chemical,and enzymatic treatments.The effectiveness of decellularization was verified by histological analysis and DNA quantification.The properties of the DTSs were evaluated by quantitative analysis of biochemical characterization,porosimetry,in vitro biocompatibility assessment,and biomechanical testing.Subsequently,the ADSCs-DTS complexes were constructed via cell injection assisted by LP or under atmospheric pressure.The differences in cell distribution,biomechanical properties,and the total DNA content were compared by histological analysis,biomechanical testing,and DNA quantification,respectively.Results Histological analysis confirmed that no cells or condensed nuclear materials were retained within the DTSs with widened interfibrillar space.The decellularization treatment resulted in a significant decrease in the content of DNA and glycosaminoglycans,and a significant increase in the porosity.The DTSs were cytocompatible in vitro and did not show reduced collagen content and inferior biomechanical properties compared with the fresh-frozen tendons.The assistance of LP promoted the broader distribution of cells into the adjacent interfibrillar space and cell proliferation in DTSs.The biomechanical properties of the scaffolds were not significantly affected by the recellularization treatments.Conclusion A novel LP-assisted approach for the construction of cells-DTS complex was established,which could be a methodological foundation for further bioreactor and in vitro studies.展开更多
NiCoCrAlYTa coatings have been deposited onto an aircraft gas turbine engine blade using a LPPS unit equipped with a computerized robot. Optimal processing conditions, including spray parameters, the trajectory of the...NiCoCrAlYTa coatings have been deposited onto an aircraft gas turbine engine blade using a LPPS unit equipped with a computerized robot. Optimal processing conditions, including spray parameters, the trajectory of the robot, and the synchronized movements between the torch and the blade, have been developed for superior coating properties. Transferred arc treatment, providing a preheating and a cleaning of the substrate surface, enhances the adherence of the coatings to the substrate. The resulting LPPS coatings show dense and uniform characteristics with ideal hardness, and good corrosion resistance to cycle oxidation.展开更多
针对甲醇发动机难以形成浓度合适的混合气而造成冷起动困难的问题,以一台应用自主开发的进气道低压空气辅助喷射系统(air assisted port injection,AAPI)的单缸甲醇发动机为研究对象开展试验研究,探究不采用辅助措施通过AAPI喷射实现甲...针对甲醇发动机难以形成浓度合适的混合气而造成冷起动困难的问题,以一台应用自主开发的进气道低压空气辅助喷射系统(air assisted port injection,AAPI)的单缸甲醇发动机为研究对象开展试验研究,探究不采用辅助措施通过AAPI喷射实现甲醇高雾化对甲醇发动机冷起动的影响及规律。试验表明AAPI明显加快了甲醇发动机冷起动前可燃混合气的形成速率。AAPI甲醇发动机着火前过量空气系数λ的平均变化率值和峰值变化率分别是普通喷射方式的3.2倍和2.26倍。点火时刻对AAPI甲醇发动机冷起动影响较大,为使AAPI甲醇发动机的冷起动性能最优,需配合合适的点火时刻,试验条件下最佳点火时刻为活塞压缩上止点前20°。AAPI甲醇发动机的冷起动性能受环境温度影响较大,随着环境温度的降低,甲醇发动机冷起动时间增长;不采用辅助措施,AAPI甲醇发动机在5℃时能实现可靠冷起动。展开更多
基金Supported by National High Technology Research and Development Program ("863" Program) of China (No.2008AA11A114)
文摘A set of compressed natural gas (CNG) multi-point direct injection system of spark-ignited engines and the corresponding measurement and data acquisition systems were developed in this paper. Based on different injection modes, the mixture formation and combustion of CNG low-pressure direct injection (LPDI) engines were studied under varying factors such as air/ fuel ratio, injection timing. Meanwhile, three-dimensional simulations were adopted to explain the mixture formation mechanisms of CNG low-pressure compound direct injection (LPCDI) mode. On the basis of test results and simulation of the mixture homogeneous degree, the conception of injection window was proposed, and the LPCDI mode was proved to be more beneficial to the mixture concentration stratification formation in cylinder under lean-burning conditions, which resulted in effective combustion and stability.
文摘A rotor dynamic model is built up for investigating the effects of tightening torque on dynamic characteristics of low pressure rotors connected by a spline coupling.The experimental rotor system is established using a fluted disk and a speed sensor which is applied in an actual aero engine for speed measurement.Through simulating calculation and experiments,the effects of tightening torque on the dynamic characteristics of the rotor system connected by a spline coupling including critical speeds,vibration modes and unbalance responses are analyzed.The results show that when increasing the tightening torque,the first two critical speeds and the amplitudes of unbalance response gradually increase in varying degrees while the vibration modes are essentially unchanged.In addition,changing axial and circumferential positions of the mass unbalance can lead to various amplitudes of unbalance response and even the rates of change.
基金the National Natural Science Foundation of China(No.81672166).
文摘Objective The goal of this study was to develop a decellularized tendon scaffold(DTS)and repopulate it with adipose-derived stem cells(ADSCs)assisted by low air pressure(LP).Methods The porcine superficial flexor tendons were processed into the DTSs using a combination of physical,chemical,and enzymatic treatments.The effectiveness of decellularization was verified by histological analysis and DNA quantification.The properties of the DTSs were evaluated by quantitative analysis of biochemical characterization,porosimetry,in vitro biocompatibility assessment,and biomechanical testing.Subsequently,the ADSCs-DTS complexes were constructed via cell injection assisted by LP or under atmospheric pressure.The differences in cell distribution,biomechanical properties,and the total DNA content were compared by histological analysis,biomechanical testing,and DNA quantification,respectively.Results Histological analysis confirmed that no cells or condensed nuclear materials were retained within the DTSs with widened interfibrillar space.The decellularization treatment resulted in a significant decrease in the content of DNA and glycosaminoglycans,and a significant increase in the porosity.The DTSs were cytocompatible in vitro and did not show reduced collagen content and inferior biomechanical properties compared with the fresh-frozen tendons.The assistance of LP promoted the broader distribution of cells into the adjacent interfibrillar space and cell proliferation in DTSs.The biomechanical properties of the scaffolds were not significantly affected by the recellularization treatments.Conclusion A novel LP-assisted approach for the construction of cells-DTS complex was established,which could be a methodological foundation for further bioreactor and in vitro studies.
文摘NiCoCrAlYTa coatings have been deposited onto an aircraft gas turbine engine blade using a LPPS unit equipped with a computerized robot. Optimal processing conditions, including spray parameters, the trajectory of the robot, and the synchronized movements between the torch and the blade, have been developed for superior coating properties. Transferred arc treatment, providing a preheating and a cleaning of the substrate surface, enhances the adherence of the coatings to the substrate. The resulting LPPS coatings show dense and uniform characteristics with ideal hardness, and good corrosion resistance to cycle oxidation.
文摘针对甲醇发动机难以形成浓度合适的混合气而造成冷起动困难的问题,以一台应用自主开发的进气道低压空气辅助喷射系统(air assisted port injection,AAPI)的单缸甲醇发动机为研究对象开展试验研究,探究不采用辅助措施通过AAPI喷射实现甲醇高雾化对甲醇发动机冷起动的影响及规律。试验表明AAPI明显加快了甲醇发动机冷起动前可燃混合气的形成速率。AAPI甲醇发动机着火前过量空气系数λ的平均变化率值和峰值变化率分别是普通喷射方式的3.2倍和2.26倍。点火时刻对AAPI甲醇发动机冷起动影响较大,为使AAPI甲醇发动机的冷起动性能最优,需配合合适的点火时刻,试验条件下最佳点火时刻为活塞压缩上止点前20°。AAPI甲醇发动机的冷起动性能受环境温度影响较大,随着环境温度的降低,甲醇发动机冷起动时间增长;不采用辅助措施,AAPI甲醇发动机在5℃时能实现可靠冷起动。
