Melting heat transfer in the boundary layer flow of a couple stress fluid over a stretching surface is investigated. The developed differential equations are solved for homotopic solutions. It is observed that the vel...Melting heat transfer in the boundary layer flow of a couple stress fluid over a stretching surface is investigated. The developed differential equations are solved for homotopic solutions. It is observed that the velocity and the boundary layer thickness are decreasing functions of the couple stress fluid parameter. However, the temperature and surface heat transfer increase when the values of the couple stress fluid parameter increase. The velocity and temperature fields increase with an increase in the melting process of the stretching sheet.展开更多
The effects of vacuum induction melting(VIM) and vacuum arc remelting(VAR) processes on the microstructure and stress rupture properties of Ni-based GTD-111 superalloy were investigated. Samples of GTD-111 master allo...The effects of vacuum induction melting(VIM) and vacuum arc remelting(VAR) processes on the microstructure and stress rupture properties of Ni-based GTD-111 superalloy were investigated. Samples of GTD-111 master alloy were melted in VIM and VAR furnaces and then poured into a preheated ceramic mold for VIM melt or into a water-cooled copper mold for VAR melt. The as-cast samples were examined radiographically to ensure that no casting defects were present in the final castings; the samples were then heat-treated using a standard heat-treatment cycle. The microstructure of the samples was investigated using optical microscopy and scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy for microanalysis. On the basis of standard ASTM-E139, stress rupture tests were carried out at 1000°C under a stress of 300 MPa. The results showed that a γ matrix, fine γ′ precipitates, a γ–γ′ eutectic structure, carbide particles, and some harmful phases such as σ and η phases were present in the as-cast samples. The γ′ precipitates with cubic morphology appeared in the matrix after the standard heat-treatment process. The extent of segregation and the amount of γ–γ′ eutectic structure formed in the VAR-prepared sample were less than in the VIM-prepared sample. The results of stress rupture tests showed that the rupture time for the VAR sample was 43% longer than that for the VIM sample.展开更多
The mismatch of elasticity modulus has limited the application of titanium alloys in medical implants,and porous structures have been proved effective to deal with this problem. However,the manufacturing of porous str...The mismatch of elasticity modulus has limited the application of titanium alloys in medical implants,and porous structures have been proved effective to deal with this problem. However,the manufacturing of porous structures has been restricted from conventional technologies. In this study,selective laser melting( SLM) technology was employed to produce a set of Ti-6Al-4V porous samples based on cubic lattices with varying size of strut width from 200 μm to 600 μm. Then the compression tests were conducted to analyze the influence of the strut width on the elasticity modulus and the ultimate strength. The result shows both of them increases linearly with the growth of strut width or with the decrease of porosity,and the elasticity modulus of porous parts is largely reduced and actually meets the requirement of clinical application. Additionally,a finite element model was established to verify the un-uniform stress distribution of porous parts. It reveals that fractures always initially occur at the vertical struts along the force direction which suffer from the main deformation.展开更多
Selective Laser Melting (SLM) shows a big potential among metal additive manufacturing (AM) technologies. However, the large thermal gradients and the local melting and solidification processes of SLM result in the pr...Selective Laser Melting (SLM) shows a big potential among metal additive manufacturing (AM) technologies. However, the large thermal gradients and the local melting and solidification processes of SLM result in the presence of a significant amount of residual stresses in the as built parts. These internal stresses will not only affect mechanical properties, but also increase the risk of Stress Corrosion Cracking (SCC). A twister used in an air extraction pump of a condenser to create a swirl in the water, was chosen as a candidate component to be produced by SLM in 316 L stainless steel. Since the main expected damage mechanism of this component in service is corrosion, corrosion tests were carried out on an as-built twister as well as on heat treated components. It was shown that a low temperature heat treatment at 450℃ had only a limited effect on the residual stress reduction and concomitant corrosion properties, while the internal stresses were significantly reduced when a high temperature heat treatment at 950℃ was applied. Furthermore, a specific stress corrosion sensitivity test proved to be a useful tool to evaluate the internal stress distribution in a specific component.展开更多
The behavior of flow stress of Al sheets used for pressure can prepared by different melt-treatment during plastic deformation at elevated temperature was studied by isothermal compression test using Gleeble1500 dynam...The behavior of flow stress of Al sheets used for pressure can prepared by different melt-treatment during plastic deformation at elevated temperature was studied by isothermal compression test using Gleeble1500 dynamic hot-simulation testing machine. The results show that the AI sheets possess the remarkable characteristic of steady state flow stress when they are deformed in the temperature range of 350-500℃ at strain rates within the range of 0.01-10.0s^-1. A hyperbolic sine relationship is found to correlate well the flow stress with the strain rate, and an Arrhenius relationship with the temperature, which implies that the process of plastic deformation at elevated temperature for this material is thermally activated. Compared with the AI pieces prepared by no or conventional melt-treatment, hot deformation activation energy of AI sheets prepared by high-efficient melt-treatment is the smallest （ Q= 168.0kJ/mol）, which reveals that the hot working formability of this material is very better, and has directly to do with the effective improvement of its metallurgical quality.展开更多
Thermal self-compressing bonding(TSCB) is a new solid-state bonding method pioneered by the authors. With electron beam as the non-melted heat source, previous experimental study performed on titanium alloys has prove...Thermal self-compressing bonding(TSCB) is a new solid-state bonding method pioneered by the authors. With electron beam as the non-melted heat source, previous experimental study performed on titanium alloys has proved the feasibility of TSCB. However, the thermal stress–strain process during bonding, which is of very important significance in revealing the mechanism of TSCB, was not analysed. In this paper, finite element analysis method is adopted to numerically study the thermal elasto-plastic stress–strain cycle of thermal self-compressing bonding. It is found that due to the localized heating, a non-uniform temperature distribution is formed during bonding, with the highest temperature existed on the bond interface. The expansion of high temperature materials adjacent to the bond interface are restrained by surrounding cool materials and rigid restraints, and thus an internal elasto-plastic stress–strain field is developed by itself which makes the bond interface subjected to thermal compressive action. This thermal self-compressing action combined with the high temperature on the bond interface promotes the atom diffusion across the bond interface to produce solid-state joints. Due to the relatively large plastic deformation, rigid restraint TSCB obtains sound joints in relatively short time compared to diffusion bonding.展开更多
Hf lowers the incipient melting temperature of superalloy. As carbon content in Hf-bearing alloy decreases, the incipient melting temperature drops furthey. PD ingots have stronger tendency to incipient melting than H...Hf lowers the incipient melting temperature of superalloy. As carbon content in Hf-bearing alloy decreases, the incipient melting temperature drops furthey. PD ingots have stronger tendency to incipient melting than HRS ones. Even though in PD ingot, the sensitivities at both ends of the ingot are quite different. The melting of Ni_5Hf phase may be considered as one of the main factors affecting incipient melting. The more Ni_5Hf the alloy contains, the more serious the incipient melting becomes. The results of differential thermal analysis (DTA) have proved that the peak of 1135-1160℃ corresponds to the melting range or Ni_5Hf. By means of a pretreatment at 1150℃, 8h, Ni_5Hf phase can be eliminated in two ways: the reaction Ni_5Hf+γ(C)→MC_(2)+γ and solid solution, and therefore the final solid solution treatment can be carried out at 1260℃. This brings about a high homogenized structure and further increases the stress rupture properties of the alloy at 1040℃, 140 MPa.展开更多
A thermal fatigue behaviour of Co-based alloy coating obtained by laser surface meltcasting on the high temperature alloy GH33 was studied.The results show that after each time of thermal cycling,the final residual st...A thermal fatigue behaviour of Co-based alloy coating obtained by laser surface meltcasting on the high temperature alloy GH33 was studied.The results show that after each time of thermal cycling,the final residual stress was formed in the melt-casting layer which is attributed to the thermal stress and structural stress.Through the first 50 times of thermal cycling,the morphology of coating still inherits the laser casting one,but the dendrites get bigger;After the second 50 times of thermal cycling,corrosion pits emerge from coating,and mostly in the places where coating and substrate meet.The fatigue damage type of coating belongs to stress corrosion.展开更多
Although Electron Beam Melting (EBM) is an innovative technology, the fatigue properties of materials manufactured by EBM may be lower than those of casted and wrought materials due to defects and surface roughness. I...Although Electron Beam Melting (EBM) is an innovative technology, the fatigue properties of materials manufactured by EBM may be lower than those of casted and wrought materials due to defects and surface roughness. In order to enhance the fatigue life of components or structures manufactured by EBM, a mechanical surface treatment technology, e.g., peening, would be effective because peening introduces high compressive residual stress at the surface which can extend the fatigue life considerably. In the present study, specimens were manufactured by EBM using titanium alloy Ti-6Al-4V powder. Two types of specimens were prepared: as-built and as-machined specimens. Specimens of each type were treated by cavitation peening or shot peening. The fatigue lives of the specimens were evaluated by a plate bending fatigue tester. The residual stress and surface roughness were also evaluated. The results obtained showed that the fatigue strength of as-built specimens can be improved by 21% by cavitation peening or shot peening, and the fatigue life under particular applied stresses can also be extended by 178% by cavitation peening.展开更多
基金supported by the Deanship of Scientific Research(DSR),King Abdulaziz University,Jeddah,Saudi Arabia
文摘Melting heat transfer in the boundary layer flow of a couple stress fluid over a stretching surface is investigated. The developed differential equations are solved for homotopic solutions. It is observed that the velocity and the boundary layer thickness are decreasing functions of the couple stress fluid parameter. However, the temperature and surface heat transfer increase when the values of the couple stress fluid parameter increase. The velocity and temperature fields increase with an increase in the melting process of the stretching sheet.
文摘The effects of vacuum induction melting(VIM) and vacuum arc remelting(VAR) processes on the microstructure and stress rupture properties of Ni-based GTD-111 superalloy were investigated. Samples of GTD-111 master alloy were melted in VIM and VAR furnaces and then poured into a preheated ceramic mold for VIM melt or into a water-cooled copper mold for VAR melt. The as-cast samples were examined radiographically to ensure that no casting defects were present in the final castings; the samples were then heat-treated using a standard heat-treatment cycle. The microstructure of the samples was investigated using optical microscopy and scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy for microanalysis. On the basis of standard ASTM-E139, stress rupture tests were carried out at 1000°C under a stress of 300 MPa. The results showed that a γ matrix, fine γ′ precipitates, a γ–γ′ eutectic structure, carbide particles, and some harmful phases such as σ and η phases were present in the as-cast samples. The γ′ precipitates with cubic morphology appeared in the matrix after the standard heat-treatment process. The extent of segregation and the amount of γ–γ′ eutectic structure formed in the VAR-prepared sample were less than in the VIM-prepared sample. The results of stress rupture tests showed that the rupture time for the VAR sample was 43% longer than that for the VIM sample.
基金Sponsored by the National High Technology Research and Development Program of China(Grant No.2015AA042501)
文摘The mismatch of elasticity modulus has limited the application of titanium alloys in medical implants,and porous structures have been proved effective to deal with this problem. However,the manufacturing of porous structures has been restricted from conventional technologies. In this study,selective laser melting( SLM) technology was employed to produce a set of Ti-6Al-4V porous samples based on cubic lattices with varying size of strut width from 200 μm to 600 μm. Then the compression tests were conducted to analyze the influence of the strut width on the elasticity modulus and the ultimate strength. The result shows both of them increases linearly with the growth of strut width or with the decrease of porosity,and the elasticity modulus of porous parts is largely reduced and actually meets the requirement of clinical application. Additionally,a finite element model was established to verify the un-uniform stress distribution of porous parts. It reveals that fractures always initially occur at the vertical struts along the force direction which suffer from the main deformation.
文摘Selective Laser Melting (SLM) shows a big potential among metal additive manufacturing (AM) technologies. However, the large thermal gradients and the local melting and solidification processes of SLM result in the presence of a significant amount of residual stresses in the as built parts. These internal stresses will not only affect mechanical properties, but also increase the risk of Stress Corrosion Cracking (SCC). A twister used in an air extraction pump of a condenser to create a swirl in the water, was chosen as a candidate component to be produced by SLM in 316 L stainless steel. Since the main expected damage mechanism of this component in service is corrosion, corrosion tests were carried out on an as-built twister as well as on heat treated components. It was shown that a low temperature heat treatment at 450℃ had only a limited effect on the residual stress reduction and concomitant corrosion properties, while the internal stresses were significantly reduced when a high temperature heat treatment at 950℃ was applied. Furthermore, a specific stress corrosion sensitivity test proved to be a useful tool to evaluate the internal stress distribution in a specific component.
基金supported by the Fujian Provincial Natural Science Foundation(No.E0210011)the Educational Commission of Fujian province(No.K20014).
文摘The behavior of flow stress of Al sheets used for pressure can prepared by different melt-treatment during plastic deformation at elevated temperature was studied by isothermal compression test using Gleeble1500 dynamic hot-simulation testing machine. The results show that the AI sheets possess the remarkable characteristic of steady state flow stress when they are deformed in the temperature range of 350-500℃ at strain rates within the range of 0.01-10.0s^-1. A hyperbolic sine relationship is found to correlate well the flow stress with the strain rate, and an Arrhenius relationship with the temperature, which implies that the process of plastic deformation at elevated temperature for this material is thermally activated. Compared with the AI pieces prepared by no or conventional melt-treatment, hot deformation activation energy of AI sheets prepared by high-efficient melt-treatment is the smallest （ Q= 168.0kJ/mol）, which reveals that the hot working formability of this material is very better, and has directly to do with the effective improvement of its metallurgical quality.
基金Supported by National Natural Science Foundation of China(Grant No.51705491)
文摘Thermal self-compressing bonding(TSCB) is a new solid-state bonding method pioneered by the authors. With electron beam as the non-melted heat source, previous experimental study performed on titanium alloys has proved the feasibility of TSCB. However, the thermal stress–strain process during bonding, which is of very important significance in revealing the mechanism of TSCB, was not analysed. In this paper, finite element analysis method is adopted to numerically study the thermal elasto-plastic stress–strain cycle of thermal self-compressing bonding. It is found that due to the localized heating, a non-uniform temperature distribution is formed during bonding, with the highest temperature existed on the bond interface. The expansion of high temperature materials adjacent to the bond interface are restrained by surrounding cool materials and rigid restraints, and thus an internal elasto-plastic stress–strain field is developed by itself which makes the bond interface subjected to thermal compressive action. This thermal self-compressing action combined with the high temperature on the bond interface promotes the atom diffusion across the bond interface to produce solid-state joints. Due to the relatively large plastic deformation, rigid restraint TSCB obtains sound joints in relatively short time compared to diffusion bonding.
文摘Hf lowers the incipient melting temperature of superalloy. As carbon content in Hf-bearing alloy decreases, the incipient melting temperature drops furthey. PD ingots have stronger tendency to incipient melting than HRS ones. Even though in PD ingot, the sensitivities at both ends of the ingot are quite different. The melting of Ni_5Hf phase may be considered as one of the main factors affecting incipient melting. The more Ni_5Hf the alloy contains, the more serious the incipient melting becomes. The results of differential thermal analysis (DTA) have proved that the peak of 1135-1160℃ corresponds to the melting range or Ni_5Hf. By means of a pretreatment at 1150℃, 8h, Ni_5Hf phase can be eliminated in two ways: the reaction Ni_5Hf+γ(C)→MC_(2)+γ and solid solution, and therefore the final solid solution treatment can be carried out at 1260℃. This brings about a high homogenized structure and further increases the stress rupture properties of the alloy at 1040℃, 140 MPa.
基金Project Sponsored by Committee on Science and Technology of Guizhou Province(943068)
文摘A thermal fatigue behaviour of Co-based alloy coating obtained by laser surface meltcasting on the high temperature alloy GH33 was studied.The results show that after each time of thermal cycling,the final residual stress was formed in the melt-casting layer which is attributed to the thermal stress and structural stress.Through the first 50 times of thermal cycling,the morphology of coating still inherits the laser casting one,but the dendrites get bigger;After the second 50 times of thermal cycling,corrosion pits emerge from coating,and mostly in the places where coating and substrate meet.The fatigue damage type of coating belongs to stress corrosion.
文摘Although Electron Beam Melting (EBM) is an innovative technology, the fatigue properties of materials manufactured by EBM may be lower than those of casted and wrought materials due to defects and surface roughness. In order to enhance the fatigue life of components or structures manufactured by EBM, a mechanical surface treatment technology, e.g., peening, would be effective because peening introduces high compressive residual stress at the surface which can extend the fatigue life considerably. In the present study, specimens were manufactured by EBM using titanium alloy Ti-6Al-4V powder. Two types of specimens were prepared: as-built and as-machined specimens. Specimens of each type were treated by cavitation peening or shot peening. The fatigue lives of the specimens were evaluated by a plate bending fatigue tester. The residual stress and surface roughness were also evaluated. The results obtained showed that the fatigue strength of as-built specimens can be improved by 21% by cavitation peening or shot peening, and the fatigue life under particular applied stresses can also be extended by 178% by cavitation peening.
