Corrosion resistance and antibacterial properties of Ti−3Cu alloy prepared by selective laser melting

The corrosion resistance and antibacterial properties of Ti−3Cu alloy prepared by selective laser melting were evaluated using electrochemical experiments and a variety of antibacterial characterization.It is found that the charge transfer resistance of Ti−3Cu alloy was 4.89×10^(5)Ω∙cm^(2),which was doubled the data obtained by CP-Ti alloy.The antibacterial rates of Ti−3Cu alloy against S.mutans and P.gingivalis were 45.0%and 54.5%.And the antibacterial rates increased with the prolongation of cultivation time,reaching up to 62.8%and 68.6%,respectively.The in-situ nano Ti_(2)Cu precipitates were homogeneously distributed in the matrix of the Ti−3Cu alloy,which was the key reason of increasing the corrosion resistance.Additionally,the microscale electric fields between theα-Ti matrix and the Ti_(2)Cu was responsible for the enhancement of the antibacterial properties.

Microstructural evolution and mechanical properties of laser melting deposited Ti-6.5Al-3.5Mo-1.5Zr-0.3Si titanium alloy

A rectangular plate of Ti-6.5A1-3.5Mo-I.5Zr-0.3Si titanium alloy was fabricated by laser melting deposition （LMD） technology. Macrostructure and microstructure were characterized by optical microscope （OM） and scanning electron microscope （SEM）. Room temperature tensile properties were evaluated. Results indicate that the macro-morphology is dominated by large columnar grains traversing multiple deposited layers. Two kinds of bands, named the wide bands and the narrow bands, are observed. The wide band consists of crab-like a lath and Widmanstatten a colony. The narrow band consists of a lath and transformed ft. The formation mechanism of the two bands was explored. The influence of heat effect caused by subsequent deposition layers on microstructural evolution during deposition process was discussed. The room temperature tensile test demonstrates that the strength of laser deposited Ti-6.5A1-3.5Mo-I.5Zr-0.3Si is comparable to that of wrought bars.

Effects of solute supersaturation and re-precipitation on microstructure and mechanical properties of selective laser melted Al−Mn−Mg−Sc−Zr alloys

A new Al−4.87Mn−1.42Mg−0.63Sc−0.20Zr(wt.%)alloy was fabricated by selective laser melting(SLM)and its microstructure and mechanical properties before and after aging were investigated.The results show that at a laser power input of 300 W,increasing laser scanning speeds from 700 to 1500 mm/s improves the mechanical properties.In the meantime,the lattice distortion values increase from 0.15%to 0.31%,showing an increasing solute supersaturation.At a laser scanning speed of 1500 mm/s,the yield strength,ultimate tensile strength and elongation of the as-SLM alloys are 356 MPa,412 MPa and 17.7%,respectively.After aging at 350°C for 8 h,these values increase to 527 MPa,554 MPa and 10.4%,respectively.The contributions to the yield strength increments from the secondary Al6(Fe,Mn)needle-like phase and re-precipitated L12 structured Al6(Sc,Zr,Ti)nano-particles during aging are 74 and 79 MPa,respectively.As the aging temperature increases to 450°C,the dominant precipitation strengthening is attributed to the secondary Al6(Sc,Zr,Ti)nano-particles.

Role of processing parameters on relative density,microstructure and mechanical properties of selective laser melted titanium alloy

The relationships between the selective laser melting(SLM)processing parameters including laser power,scanning speed and hatch space,the relative density,the microstructure,and resulting mechanical properties of Ti-6Al-2Zr-1Mo-1V alloy were investigated in this work.The result shows that laser power acts a dominant role in determining the relative density in comparison with scanning speed and hatch space.The optimal SLM process window for fabricating relative density>99%samples is located in the energy density range of 34.72 J·mm^(-3)to 52.08 J·mm^(-3),where the laser power range is between 125 W and 175 W.An upward trend is found in the micro-hardness as the energy density is increased.The optimum SLM processing parameters of Ti-6Al-2Zr-1Mo-1V alloy are:laser power of 150 W,scanning speed of 1,600 mm·s^(-1),hatch space of 0.08 mm,and layer thickness of 0.03 mm.The highest ultimate tensile strength,yield strength,and ductility under the optimum processing parameter are achieved,which are 1,205 MPa,1,099 MPa,and 8%,respectively.The results of this study can be used to guide SLM production Ti-6Al-2Zr-1Mo-1V alloy parts.

Enhanced mechanical properties and formability of 316L stainless steel materials 3D-printed using selective laser melting

This study is conducted to develop an innovative and attractive selective laser melting(SLM)method to produce 316 L stainless steel materials with excellent mechanical performance and complex part shape.In this work,the subregional manufacturing strategy,which separates the special parts from the components using an optimized process,was proposed.The results showed that produced 316 L materials exhibited superior strength of^755 MPa and good ductility.In the as-built parts,austenite with preferred orientation of the(220)plane,δ-ferrite,and a small amount of CrO phases were present.In addition,the crystal size was fine,which contributed to the enhancement of the parts’mechanical properties.The structural anisotropy mechanism of the materials was also investigated for a group of half-sized samples with variable inclination directions.This technique was used to fabricate a set of impellers with helical bevels and high-precision planetary gears,demonstrating its strong potential for use in practical applications.

Anisotropy in mechanical properties and corrosion resistance of 316L stainless steel fabricated by selective laser melting

The corrosion behavior and mechanical properties of 316 L stainless steel(SS) fabricated via selective laser melting(SLM) were clarified by potentiodynamic polarization measurements, immersion tests, and tensile experiments. The microstructural anisotropy of SLMed 316 L SS was also investigated by electron back-scattered diffraction and transmission electron microscopy. The grain sizes of the SLMed 316 L SS in the XOZ plane were smaller than those of the SLMed 316 L SS in the XOY plane, and a greater number of low-angle boundaries were present in the XOY plane, resulting in lower elongation for the XOY plane than for the XOZ plane. The SLMed 316 L was expected to exhibit higher strength but lower ductility than the wrought 316 L, which was attributed to the high density of dislocations. The pitting potentials of the SLMed 316 L samples were universally higher than those of the wrought sample in chloride solutions because of the annihilation of MnS or(Ca,Al)-oxides during the rapid solidification. However, the molten pool boundaries preferentially dissolved in aggressive solutions and the damage of the SLMed 316 L in FeCl3 solution was more serious after long-term service, indicating poor durability.

Effect of Nb additions on microstructure and properties of γ-TiAl based alloys fabricated by selective laser melting

The γ-TiAl based Ti.Al.Mn.Nb alloys with different Nb additions were fabricated by selective laser melting (SLM) on the TC4 substrate. The effects of Nb content on microstructure and properties of the alloys were investigated. The results reveal that the alloys consist of γ-TiAl phase with tetragonal lattice structure and α2-Ti3Al phase with hcp lattice structure, and show a sequential structure change from near full dendrite to near lamellar structure with the increase of Nb addition. Owing to the higher Nb content in γ-TiAl phase and the formation of near lamellar structure, the alloy with 7.0 at.% Nb addition has the best combination of properties among the studied alloys, namely, not only a high hardness of HV 2000, a high strength of 1390 MPa and a plastic deformation of about 24.5%, but also good tribological properties and high-temperature oxidation resistance.

Effects of annealing on microstructure and mechanical properties of γ-TiAl alloy fabricated via laser melting deposition

The microstructure evolution and mechanical properties of the as-deposited γ-TiAl-based alloy specimen fabricated via laser melting deposition and as-annealed specimens at different temperatures were investigated.The results show that the microstructure of as-deposited specimen is composed of fineα2(Ti3Al)+γlamellae.With the increase of annealing temperature,the bulk γ m(TiAl)phase gradually changes from single γ phase toγphase+acicularα2 phase,finally small γ phase+lamellar α2+γ phase.Compared with the mechanical properties of as-depositedγ-TiAl alloy(tensile strength 469 MPa,elongation 1.1%),after annealing at 1260℃ for 30 min followed by furnace cooling(FC),the room-temperature tensile strength of the specimen is 543.4 MPa and the elongation is 3.7%,which are obviously improved.

Corrosion and wear properties of micro-arc oxidation treated Ti6Al4V alloy prepared by selective electron beam melting

In order to analyze the effect of voltage during micro-arc oxidation(MAO)on corrosion and wear properties of Ti6Al4V(TC4),the MAO technology was employed to treat TC4 samples fabricated by selective electron beam melting(SEBM)at the voltages of 400,420 and 450 V.The results show that the metastable anatase phase gradually transforms to rutile phase with oxidation time and temperature increasing.The surface morphology of coating contains numerous micropores with uniform size distribution.Cracks and pores over 10μm are found on MAO-TC4 sample with applied voltage of 450 V.The thickness of MAO coating is positively correlated with the voltage.The corrosion resistance and wear resistance are related to phase composition,micropore size distribution on the surface and film thickness.When the voltage is 420 V,the coating shows the smallest corrosion current density(0.960×10^-7 A/cm^2)and the largest resistance(7.17×10^5Ω·cm^2).Under the same load condition,the coating exhibits larger friction coefficient and wear loss than the TC4 substrate.With the increase of voltage,the wear mechanism of the coating changes from abrasive wear to adhesive wear,and the adhesive wear is intensified at applied voltage of 450 V,with a maximum friction coefficient of 0.821.

Influence of process parameters and aging treatment on the microstructure and mechanical properties of Al Si8Mg3 alloy fabricated by selective laser melting

Many studies have investigated the selective laser melting(SLM)of AlSi10Mg and AlSi7Mg alloys,but there are still lack of researches focused on Al-Si-Mg alloys specifically tailored for SLM.In this work,a novel high Mg-content AlSi8Mg3 alloy was specifically designed for SLM.The results showed that this new alloy exhibited excellent SLM processability with a lowest porosity of 0.07%.Massive lattice distortion led to a high Vickers hardness in samples fabricated at a high laser power due to the precipitation of Mg_(2)Si nanoparticles from theα-Al matrix induced by high-intensity intrinsic heat treatment during SLM.The maximum microhardness and compressive yield strength of the alloy reached HV(211±4)and(526±12)MPa,respectively.After aging treatment at 150℃,the maximum microhardness and compressive yield strength of the samples were further improved to HV(221±4)and(577±5)MPa,respectively.These values are higher than those of most known aluminum alloys fabricated by SLM.This paper provides a new idea for optimizing the mechanical properties of Al-Si-Mg alloys fabricated using SLM.

Mechanical properties of TiAl fabricated by electron beam melting-A review

As a typical intermetallic material,TiAl is inevitably difficult to process by conventional methods.Additive manufacturing(AM)has recently become a new option for making net-shape TiAl components.Among all AM methods,electron beam melting(EBM)shows the potential to make TiAl components with good mechanical properties and is used for low pressure turbine blades.The mechanical properties,including tensile and compression properties,fracture toughness,fatigue and creep properties of EBM TiAl are reviewed and compared to the conventionally fabricated alloys.Results show that the tensile strength of EBM alloys is higher than cast alloys,and other properties are comparable to the cast/forged alloys.The sensitivity of mechanical properties and microstructure to EBM processing parameters is presented.Issues including layered microstructure,anisotropy in mechanical properties,and fatigue failure from defects are also reviewed.Finally,some opportunities and challenges of EBM TiAl are identified.

Effect of Zr content on crack formation and mechanical properties of IN738LC processed by selective laser melting

Two batches of commercial IN738LC alloy powders with different Zr contents were printed under the same parameters.The influences of Zr content(0.024 wt.% and 0.12 wt.%,respectively) in powders on crack density,distribution,formation mechanism and mechanical properties of selective laser melting(SLM)-treated parts were systematically studied.It was found that the crack density(area ratio) increases from 0.15% to 0.87% in the XOY plane and from 0.21% to 1.81% in the XOZ plane along with the Zr content increase from 0.024 wt.% to 0.12 wt.% in the original powders.Solidification cracks are formed along the epitaxially grown <001>-oriented columnar grain boundaries in molten pool center.The ultimate tensile strength of Sample 1(0.024 wt.% Zr) is 1113 MPa,and there are dimples in tensile fracture.With an increase in the Zr content to 0.12 wt.%(Sample 2),the ultimate tensile strength of Sample 2 decreases to 610 MPa,and there are numerous original cracks and exposed columnar grain boundaries in tensile fracture.The optimization of printing parameters of Sample 2 considerably increases the ultimate tensile strength by 55.2% to 947 MPa,and the plasticity is greatly improved.

Microstructure,mechanical properties and corrosion performance of selective laser melting Ti/GNPs composite with a porous structure

In this study,nano-graphene reinforced titanium matrix composites(GNPs/Ti)with a honeycomb porous structure were fabricated by selective laser melting(SLM).The effects of graphene on the microstructure,mechanical properties and corrosion performance of the SLM GNPs/Ti were systematically investigated.Results of microstructure characterization show that:1)the density of the SLM GNPs/Ti was improved as compared to that of the SLM Ti;2)abundant TiC particles were formed in the SLM GNPs/Ti.The hardness and compressive strength of the composite increased by 90%(from HV 236 to HV 503)and 14%(from 277 MPa to 316 MPa),respectively,attributed to the uniformly distributed TiC and fine GNPs in the Ti matrix.Electrochemical tests reveal that the corrosion current density of the SLM GNPs/Ti is only 0.328μA/cm^(2),that is about 25%less than that of the SLM Ti.The results indicate that the incorporation of nano-graphene is a potential method to strengthen the Ti by SLM.

Influence of hot isostatic pressing on microstructure,properties and deformability of selective laser melting TC4 alloy

The influence of different hot isostatic pressing regimes on microstructure,phase constitution,microhardness,tensile properties and deformability of TC4 alloy fabricated by selective laser melting(SLM)technology was studied.The results show that the microstructure of SLM TC4 alloy is composed of acicular martensiteα’phase,and the sample exhibits high microhardness and strength,but low plasticity.After hot isostatic pressing,acicular martensiteα’phase transforms intoα+βphase,and with the increase of hot isostatic pressing temperature and duration,αphase with coarse lath is gradually refined,and the proportion ofαphase is gradually reduced.Because of the change of phase constitution in SLM TC4 alloy after hot isostatic pressing,the grain refinement strengthening is weakened,the density of dislocation is reduced,so that both microhardness and tensile strength are decreased by around 20%,the elongation is increased by more than about 70%,even over 100%,compared with as-deposited TC4 alloy.When the hot isostatic pressing regime is 940°C/3 h/150 MPa,the tensile strength and the elongation achieve optimal match,which are about890 MPa and around 14.0%in both directions.The fracture mechanism of alloy after 940 oC/3 h/150 MPa HIP is dultile fracture.Hot isostatic pressing causes concave deformation of SLM TC4 alloy thin-walled frames,and the deformation degree increases with the increase of temperature.

Influence of multiple laser shock peening treatments on the microstructure and mechanical properties of Ti-6Al-4V alloy fabricated by electron beam melting

Laser shock peening(LSP)is an attractive post-processing method to tailor surface microstructure and enhance mechanical performances of additive manufactured(AM)components.The effects of multiple LSP treatments on the microstructure and mechanical properties of Ti-6Al-4V part produced by electron beam melting(EBM),as a mature AM process,were studied in this work.Microstructure,surface topography,residual stress,and tensile performance of EBM-manufactured Ti-6Al-4V specimens were systematically analyzed subjected to different LSP treatments.The distribution of porosities in EBM sample was assessed via X-ray computed tomography.The results showed that EBM samples with two LSP treatments possessed a lower porosity value of 0.05%compared to the value of 0.08%for the untreated samples.The strength of EBM samples with two LSP treatments was remarkably raised by 12%as compared with the as-built samples.The grains ofαphase were refined in near-surface layer,and a dramatic increase in the depth and magnitude of compressive residual stress(CRS)was achieved in EBM sample with multiple LSP treatments.The grain refinement ofαphase and CRS with larger depth were responsible for the strength enhancement of EBM samples with two LSP treatments.

A review on microstructures and properties of high entropy alloys manufactured by selective laser melting

High entropy alloys(HEAs)with multi-component solid solution microstructures have the potential for large-scale industrial applications due to their excellent mechanical and functional properties.However,the mechanical properties of HEAs limit the selection of processing technologies.Additive manufacturing technology possesses strong processing adaptability,making itthe best candidate method to overcome this issue.This comprehensive review examines the current state of selective laser melting(SLM)of HEAs.Introducing SLM to HEAs processing is motivated by its high quality for dimensional accuracy,geometric complexity,surface roughness,and microstructure.This review focuses on analyzing the current developments and challenges in SLM of HEAs,including defects,microstructures,and properties,as well as strengthing prediction models of fabricated HEAs.This review also offers directions for future studies to address existing challenges and promote technological advancement.

Effect of arc re-melting on microstructure,mechanical and tribological properties of commercial 390A alloy

To investigate the effect of the arc re-melting on the microstructure,mechanical and tribological properties of the 390 A alloy,its ingot produced by the conventional induction melting method was subjected to the arc re-melting process.The microstructure of the 390 A alloy was examined by OM and SEM.Mechanical properties of the 390 A alloy were determined by the Brinell method and tensile tests.Tribological properties were investigated with a ball-on-disc type tester.It was observed that the microstructure of both conventional induction melted and arc re-melted 390 A alloys consisted ofα(Al),eutectic Al-12 Si,primary silicon particles,θ-CuAl_(2),β-Al_(5) FeSi,δ-Al_(4) FeSi_(2),andα-Al_(15)(FeMnCu)3 Si_(2) phases.Re-melting with the arc process caused grain refinement in these phases.In addition,after this process,theα(Al)phase and primary silicon particles were dispersed more uniformly,and sharp edges of primary silicon particles became round.The arc re-melting process resulted in an increase in the hardness of the 390 A alloy produced by the conventional method from 102 HB to 118 HB and the tensile strength from 130 to 240 MPa.It also caused an increase in the wear resistance of the 390 A alloy and a decrease in the friction coefficient.

Size-dependent melting properties of Sn nanoparticles by chemical reduction synthesis

Tin nanoparticles with different size distribution were synthesized using chemical reduction method by applying NaBH4 as reduction agent.The Sn nanoparticles smaller than 100 nm were less agglomerated and no obviously oxidized.The melting properties of these synthesized nanoparticles were studied by differential scanning calorimetry.The melting temperatures of Sn nanoparticles in diameter of 81,40,36 and 34 nm were 226.1,221.8,221.1 and 219.5？欲espectively.The size-dependent melting temperature and size-dependent latent heat of fusion have been observed.The size-dependent melting properties of tin nanoparticles in this study were also comparatively analyzed by employing different size-dependent theoretical melting models and the differences between these models were discussed.The results show that the experimental data are in accordance with the LSM model and SPI model,and the LSM model gives the better understanding for the melting property of the Sn nanoparticles.

Microstructure and properties of AlSi7Mg alloy fabricated by selective laser melting

The AlSi7Mg alloy was fabricated by selective laser melting(SLM),and its microstructure and properties at different building directions after heat treatment were analyzed.Results show that the microstructure of SLM AlSi7Mg samples containes three zones:fine grain zone,coarse grain zone,and heat affected zone.The fine-grain regions locate inside the molten pool,and the grains are equiaxed.The coarse-grain regions locate in the overlap of molten pools.After T6 treatment,the microstructure at the molten pool boundary is still the network eutectic Si,but the network structure becomes discrete,and is composed of intermittent,chain-like eutectic Si particles.The yield strength at three directions(xy,45°,z direction)of the AlSi7Mg alloy samples fabricated by SLM is improved after T6 heat treatment.The fracture mechanism of the samples is a mixed ductile and brittle fracture before heat treatment and ductile fracture after heat treatment.

Microstructures,Thermal and Mechanical Properties of Pure Tungsten—A Comparison Between Selective Laser Melting and Hot Rolling

A comparative study on the influence of different manufacturing methods(selective laser melting and hot rolling)on the microstructure,mechanical and thermal behaviours of tungsten(W)was presented for the first time.The results indicated that the selective laser melting(SLM)W exhibited a finer grain sizes,a lower strength ductility,hardness and thermal conductivity compared to hot-rolled W.The main reason for this result was that the laser underwent rapid heating and cooling when it was used to melt W powder with high energy density,resulting in large internal stress in the sample after manufacturing.Subsequently,the internal stress was released,leading to the generation of microcracks at the grain boundaries,thereby affecting the performance of SLM W samples.In addition,the higher fraction of high-angle grain boundaries(HAGBs)of SLM W was found to be the key factor for intrinsic brittleness.Because the HAGBs are the preferred crack paths,which could promote crack propagation and decrease fracture energy.