Mixed matrix membranes(MMMs)could combine the advantages of both polymeric membranes and porousfillers,making them an effective alternative to conventional polymer membranes.However,interfacial incompatibility issues,s...Mixed matrix membranes(MMMs)could combine the advantages of both polymeric membranes and porousfillers,making them an effective alternative to conventional polymer membranes.However,interfacial incompatibility issues,such as the presence of interfacial voids,hardening of polymer chains,and blockage of micropores by polymers between common MMMsfillers and the polymer matrix,currently limit the gas sep-aration performance of MMMs.Ternary phase MMMs(consisting of afiller,an additive,and a matrix)made by adding a third compound,usually functionalized additives,can overcome the structural problems of binary phase MMMs and positively impact membrane separation performance.This review introduces the structure and fabrication processes for ternary MMMs,categorizes various nanofillers and the third component,and summarizes and analyzes in detail the CO_(2) separation performance of newly developed ternary MMMs based on both rubbery and glassy polymers.Based on this separation data,the challenges of ternary MMMs are also discussed.Finally,future directions for ternary MMMs are proposed.展开更多
Acid loss and plasticization of phosphoric acid(PA)-doped high-temperature polymer electrolyte membranes(HT-PEMs)are critical limitations to their practical application in fuel cells.To overcome these barriers,poly(te...Acid loss and plasticization of phosphoric acid(PA)-doped high-temperature polymer electrolyte membranes(HT-PEMs)are critical limitations to their practical application in fuel cells.To overcome these barriers,poly(terphenyl piperidinium)s constructed from the m-and p-isomers of terphenyl were synthesized to regulate the microstructure of the membrane.Highly rigid p-terphenyl units prompt the formation of moderate PA aggregates,where the ion-pair interaction between piperidinium and biphosphate is reinforced,leading to a reduction in the plasticizing effect.As a result,there are trade-offs between the proton conductivity,mechanical strength,and PA retention of the membranes with varied m/p-isomer ratios.The designed PA-doped PTP-20m membrane exhibits superior ionic conductivity,good mechanical strength,and excellent PA retention over a wide range of temperature(80–160°C)as well as satisfactory resistance to harsh accelerated aging tests.As a result,the membrane presents a desirable combination of performance(1.462 W cm^(-2) under the H_(2)/O_(2)condition,which is 1.5 times higher than that of PBI-based membrane)and durability(300 h at 160°C and 0.2 A cm^(-2))in the fuel cell.The results of this study provide new insights that will guide molecular design from the perspective of microstructure to improve the performance and robustness of HT-PEMs.展开更多
In industry, ethylene(C_(2)H_(4))/propylene(C_(3)H_(6)) separations are usually performed by a cryogenic process,which is energy intensive. Membrane separation technology is an alternative separation process that save...In industry, ethylene(C_(2)H_(4))/propylene(C_(3)H_(6)) separations are usually performed by a cryogenic process,which is energy intensive. Membrane separation technology is an alternative separation process that saves energy and is efficient. In this study, blend membranes were prepared by doping polyethylene glycol(PEG600) into a poly(ether-block-amide)(Pebax^(■) 2533) matrix and were used to separate the C_(2)H_(4)/C_(3)H_(6) mixture. The PEG 600 and Pebax^(■) 2533 polymers have good compatibility because they share hydrogen bonds. The addition of PEG600 is conducive to the hydrophilicity and the free volume of blend membranes, and it is also conducive to the solubility of C_(2)H_(4) and C_(3)H_(6) in the membranes, which improves the ability of the membranes to separate this gas pair. The Pebax^(■) 2533/PEG600 blend membrane with 15%(mass) PEG600 showed the highest separation performance in our investigated membranes, with a C_(3)H_(6)/C_(2)H_(4) selectivity of 8.9 and a C_(3)H_(6) permeability of 196 barrer(1 barrer = 1.33×10^(14)m^(3)(STP)·m·m^(-2)·s^(-1)·kPa^(-1)) at 238 K and 0.2 MPa, which is higher than that of the Pebax^(■) 2533/NaY-6%(mass) membrane(α_(C_(3)H_(6)/C_(2)H_(4)) =6.5, P_(C_(3)H_(6))=211 barrer) reported in our previous work. It is confirmed that incorporating PEG600 into the Pebax^(■) 2533 matrix to fabricate blend membranes is an efficient strategy for separating light olefins.展开更多
During the last decade, metal-organic frameworks(MOFs) have been applied in various fields due to their unique chemical and functional advantages. One of the widespread research hotspots is MOF-based membranes for sep...During the last decade, metal-organic frameworks(MOFs) have been applied in various fields due to their unique chemical and functional advantages. One of the widespread research hotspots is MOF-based membranes for separations, specifically continuous defect-free MOF membranes, which are usually grown on porous substrates. The substrate not only serves as the MOF layer support but also has a great influence on the membrane fabrication process and the final separation performance of the resultant membrane. In this review, we mainly introduce the progress focused on the substrates for MOF membranes fabrication. The substrate modifications and seeding methods aimed at synthesizing highquality MOF membranes are also summarized systematically.展开更多
The synthesis of a continuous IMF zeolite membrane was fabricated on tubular substrates by seeded growth for the first time. The straight channels of IMF zeolite with diameters of 0.53–0.59 nm are distinguishable for...The synthesis of a continuous IMF zeolite membrane was fabricated on tubular substrates by seeded growth for the first time. The straight channels of IMF zeolite with diameters of 0.53–0.59 nm are distinguishable for p-xylene from o-xylene molecules. Pure IMF-phase high-silica IM-5 zeolite seeds with uniform and fine crystal size were fabricated by a new sonication-assisted aging process. The seeds were coated on the support by dipcoating and induced the formation of continuous membrane. Separation performance in p-/o-xylene mixture was investigated at various temperature and pressure. The typical IM-5zeolite membrane had p-/o-xylene separation factor of 3.7. Our results suggest that IM-5 zeolite is a potentially good membrane material for the separation of xylene mixtures.展开更多
Tungsten (W) incorporated mobil-type eleven (MEL) zeolite membrane (referred to as W-MEL membrane) with high separation performance was firstly explored for the separation of oil/water mixtures under the influence of ...Tungsten (W) incorporated mobil-type eleven (MEL) zeolite membrane (referred to as W-MEL membrane) with high separation performance was firstly explored for the separation of oil/water mixtures under the influence of gravity.W-MEL membranes were grown on stainless steel (SS) meshes through in-situ hydrothermal growth method facilitated with (3-aminopropyl)triethoxysilane (APTES) modification of stainless steel meshes,which promote the heterogeneous nucleation and crystal growth of W-MEL zeolites onto the mesh surface.W-MEL membranes were grown on different mesh size supports to investigate the effect of mesh size on the separation performance of the membrane.The assynthesized W-MEL membrane supported on 500 mesh (25μm)(W-MEL-500) exhibit the hydrophilic nature with a water contact angle of 11.8°and delivers the best hexane/water mixture separation with a water flux and separation efficiency of 46247 L·m^(-2)·h^(-1)and 99.5%,respectively.The wettability of W-MEL membranes was manipulated from hydrophilic to hydrophobic nature by chemically modifying with the fluorine-free compounds (hexadecyltrimethoxysilane (HDTMS) and dodecyltrimethoxysilane(DDTMS)) to achieve efficient oil-permselective separation of heavy oils from water.Among the hydrophobically modified W-MEL membranes,W-MEL-500-HDTMS having a water contact angle of146.4°delivers the best separation performance for dichloromethane/water mixtures with a constant oil flux and separation efficiency of 61490 L·m^(-2)·h^(-1)and 99.2%,respectively along with the stability tested up to 20 cycles.Both W-MEL-500-HDTMS and W-MEL-500-DDTMS membranes also exhibit similar separation performances for the separation of heavy oil from sea water along with a 20-fold lower corrosion rate in comparison with the bare stainless-steel mesh,indicating their excellent stability in seawater.Compared to the reported zeolite membranes for oil/water separation,the as-synthesized and hydrophobically modified W-MEL membranes shows competitive separation performances in terms of flux and separation efficiency,demonstrating the good potentiality for oil/water separation.展开更多
The aim of this study was to design a new emulsion liquid membrane(ELM)system for the separation of succinic acid from aqueous solutions.The concentration of succinic acid varied from 20 to 60 mmol·L^(-1).The pre...The aim of this study was to design a new emulsion liquid membrane(ELM)system for the separation of succinic acid from aqueous solutions.The concentration of succinic acid varied from 20 to 60 mmol·L^(-1).The prepared ELM system includes tributylamine(TBA)as a carrier,commercial kerosene as a solvent,Span 80 as a surfactant,and Na2CO3as a stripping agent.In order to control the membrane swelling,different values of cyclohexanone were added to the membrane phase.The effect of various empirical variables on the extraction of the succinic acid such as acid concentration in the feed solution,initial feed concentration,carrier concentration,the stirring speed of the extraction,Na2CO3,surfactant,and cyclohexanone concentrations,and treat ratio in the ELM system.The best result was obtained when TBA was used as the carrier.The final acid extraction efficiency was independent of pH variations of the aqueous feed solution.The extraction of succinic acid solution with a concentration of 40 mmol·L^(-1)was improved by increasing the treat ratio 1:7-1:3,stripping phase concentration 0.5-1.5 mol·L^(-1),stirring speed 300-500 r·min^(-1)and cyclohexanone concentration in the membrane phase 1.2-1.6 mol·L^(-1).No considerable effect on the extraction rate was observed for the carrier concentration in the membrane phase.But,the surfactant concentration in the feed phase showed a dual effect on the extraction efficiency.展开更多
Nowadays, oil contamination has become a major reason for water pollution, and presents a global environmental challenge. Although many efforts have been devoted to the fabrication of oil/water separation materials, t...Nowadays, oil contamination has become a major reason for water pollution, and presents a global environmental challenge. Although many efforts have been devoted to the fabrication of oil/water separation materials, their practical applications are still hindered by their weak durability, poor chemical tolerance,environmental resistance, and potential negative impact on health and the environment. To overcome these drawbacks, this work offers a facile method to fabricate the eco-friendly and durable oil/water separation membrane fabrics by alkaline hydrolysis and silicon polyurethane coating. The X-ray photoelectron spectroscopy, scanning electron microscopy, and atomic force microscopy results demonstrate that silicon polyurethane membrane could be coated onto the surface of hydrolyzed polyester fabric and form a micro-/nano-scaled hierarchical structure. Based on this, the modified fabric could have a stable superhydrophobic property with a water contact angle higher than 150°, even after repeated washing and mechanical abrasion 800 times, as well as chemical corrosion. Moreover, the modified fabrics show excellent oil/water separation efficiency of up to 99% for various types of oil–water mixture. Therefore, this durable, eco-friendly and cost-efficient superhydrophobic fabric has great potential in large-scale oil/water separation.展开更多
Membrane separation technology with the ability to regulate gas/liquid transport and separation is critical for environmental fields, such as sewerage treatment, multiphase separation, and desalination. Although numer...Membrane separation technology with the ability to regulate gas/liquid transport and separation is critical for environmental fields, such as sewerage treatment, multiphase separation, and desalination. Although numerous membranes can dynamically control liquid-phase fluids transport via external stimuli, the transport and separation of gas-phase fluids remains a challenge. Here, we show a temperature-regulation liquid gating membrane that allows in-situ dynamically controllable gas/liquid transfer and multiphase separation by integrating a thermo-wettability responsive porous membrane with functional gating liquid. Experiments and theoretical analysis have demonstrated the temperature-regulation mechanism of this liquid gating system, which is based on thermo-responsive changes of porous membrane surface polarity, leading to changes in affinity between the porous membrane and the gating liquid. In addition, the sandwich configuration with dense Au-coated surfaces and heterogeneous internal components by a bistable interface design enables the liquid gating system to enhance response sensitivity and maintain working stability. This temperature-regulation gas/liquid transfer strategy expands the application range of liquid gating membranes,which are promising in environmental governance, water treatment and multiphase separation.展开更多
Perovskite-type mixed protonic-electronic conducting membranes have attracted attention because of their ability to separate and purify hydrogen from a mixture of gases generated by industrial-scale steam reforming ba...Perovskite-type mixed protonic-electronic conducting membranes have attracted attention because of their ability to separate and purify hydrogen from a mixture of gases generated by industrial-scale steam reforming based on an ion diffusion mechanism.Exploring cost-effective membrane materials that can achieve both high H_(2) permeability and strong CO_(2)-tolerant chemical stability has been a major challenge for industrial applications.Herein,we constructed a triple phase(ceramic-metal-ceramic)membrane composed of a perovskite ceramic phase BaZr_(0.1)Ce_(0.7)Y_(0.1)Yb_(0.1)O_(3-δ)(BZCYYb),Ni metal phase and a fluorite ceramic phase CeO_(2).Under H_(2) atmosphere,Ni metal in-situ exsolved from the oxide grains,and decorated the grain surface and boundary,thus the electronic conductivity and hydrogen separation performance can be promoted.The BZCYYbNi-CeO_(2)hybrid membrane achieved an exceptional hydrogen separation performance of 0.53 mL min^(-1)cm^(-2) at 800℃ under a 10 vol% H_(2) atmosphere,surpassing all other perovskite membranes reported to date.Furthermore,the CeO_(2) phase incorporated into the BZCYYb-Ni effectively improved the CO_(2)-tolerant chemical stability.The BZCYYbNi-CeO_(2) membrane exhibited outstanding long-term stability for at least 80 h at 700℃ under 10 vol%CO_(2)-10 vol%H_(2).The success of hybrid membrane construction creates a new direction for simultaneously improving their hydrogen separation performance and CO_(2) resistance stability.展开更多
Layered assembled membranes of 2D leaf-like zeolitic imidazolate frameworks(ZIF-L)nanosheets have received great attention in the field of water treatment due to the porous structure and excellent antibacterial abilit...Layered assembled membranes of 2D leaf-like zeolitic imidazolate frameworks(ZIF-L)nanosheets have received great attention in the field of water treatment due to the porous structure and excellent antibacterial ability,but the dense accumulation on the membrane surface and the low permeate flux greatly hinder their application.Herein,we synthesized m HNTs(modified halloysite nanotubes)/ZIF-L nanocomposites on modified m HNTs by in situ growth method.Interestingly,due to the different size of m HNTs and ZIF-L,m HNTs were packed in ZIF-L nanosheets.The hollow m HNTs provided additional transport channels for water molecules,and the accumulation of the ZIF-L nanosheets was decreased after assembling m HNTs/ZIF-L nanocomposites into membrane by filtration.The prepared m HNTs/ZIF-L membrane presented high permeate flux(59.6 L·m^(-2)·h^(-1)),which is 2-4 times of the ZIF-L membranes(14.8 L·m^(-2)·h^(-1)).Moreover,m HNTs/ZIF-L membranes are intrinsically antimicrobial,which exhibit extremely high bacterial resistance.We provide a controllable strategy to improve 2D ZIF-L assembles,and develops novel membranes using 2D package structure as building units.展开更多
With the rapid development of portable technology,lithium batteries have emerged as potential candidates for high-performance energy storage systems owing to their high energy density and cycling stability.Among the k...With the rapid development of portable technology,lithium batteries have emerged as potential candidates for high-performance energy storage systems owing to their high energy density and cycling stability.Among the key components of a lithium battery system,the separator plays a critical role as it directly influences the battery performance benchmark(cycling performance and safety).However,traditional polyolefin separators(polypropylene/polyethylene)are unable to meet the demands of highperformance and safer battery systems due to their poor electrolyte compatibility,thermal runaways,and ultimate growth of dendrites.In contrast,membranes fabricated using polybenzimidazole(PBI)exhibit excellent electrolyte wettability and outstanding thermal dimensional stability,thus holding great potential as separators for high-performance and high-safety batteries.In this paper,we present a comprehensive review of the general requirements for separators,synthesis technology for separators,and research trends focusing PBI membranes in lithium batteries to alleviate the current commercial challenges faced by conventional polyolefin separators.In addition,we discuss the future development direction for PBI battery separators by considering various factors such as production cost,ecological footprint,preparation technology,and battery component compatibility.By exploring these perspectives,we aim to promote the continued application and exploration of PBI-based materials to advance lithium battery technology.展开更多
Cu catalysts can convert CO_(2) through an electrochemical reduction reaction into a variety of useful carbon-based products.However,this capability provides an obstacle to increasing the selectivity for a single prod...Cu catalysts can convert CO_(2) through an electrochemical reduction reaction into a variety of useful carbon-based products.However,this capability provides an obstacle to increasing the selectivity for a single product.Herein,we report a simple fabrication method for a Cu-Pd alloy catalyst for use in a membrane electrode assembly(MEA)-based CO_(2) electrolyzer for the electrochemical CO_(2) reduction reaction(ECRR)with high selectivity for CO production.When the composition of the Cu-Pd alloy catalyst was fabricated at 6:4,the selectivity for CO increased and the production of multi-carbon compounds and hydrogen is suppressed.Introducing a Cu-Pd alloy catalyst with 6:4 ratio as the cathode of the MEAbased CO_(2) electrolyzer showed a CO faradaic efficiency of 92.8%at 2.4 V_(cell).We assumed that these results contributed from the crystal planes on the surface of the Cu-Pd alloy.The phases of the Cu-Pd alloy catalyst were partially separated through annealing to fabricate a catalyst with high selectivity for CO at low voltage and C_(2)H_4 at high voltage.The results of CO-stripping testing confirmed that when Cu partially separates from the lattice of the Cu-Pd alloy,the desorption of~*CO is suppressed,suggesting that C-C coupling reaction is favored.展开更多
Hydrogen is an alternative energy source that has the potential to replace fossil fuels.One of the hydrogen applications is as a material for Polymer Electrolyte Membrane Fuel Cells(PEMFC)in fuel cell vehicles.High-pu...Hydrogen is an alternative energy source that has the potential to replace fossil fuels.One of the hydrogen applications is as a material for Polymer Electrolyte Membrane Fuel Cells(PEMFC)in fuel cell vehicles.High-purity hydrogen can be obtained using a hydrogen separation membrane to prevent unwanted contaminants from potentially harming the PEMFC components.In this study,we fabricated a plasma membrane reactor and investigated the permeation performance of a hydrogen separation membrane in a plasma membrane reactor utilizing atmospheric pressure plasma.The result showed the hydrogen permeation rate increasing with time as reactor temperature is increased through joule heating.By decreasing the gap length of the reactor from 2 to 1 mm,the hydrogen permeation rate increases by up to 40%.The hydrogen permeation rate increases by 30%when pressure is applied to the plasma membrane reactor by up to 100 kPa.展开更多
Recent advances on mixed matrix membrane for CO_2 separation are reviewed in this paper. To improve CO_2 separation performance of polymer membranes, mixed matrix membranes(MMMs) are developed. The concept of MMM is i...Recent advances on mixed matrix membrane for CO_2 separation are reviewed in this paper. To improve CO_2 separation performance of polymer membranes, mixed matrix membranes(MMMs) are developed. The concept of MMM is illustrated distinctly. Suitable polymer and inorganic or organic fillers for MMMs are summarized.Possible interface morphologies between polymer and filler, and the effect of interface morphologies on gas transport properties of MMMs are summarized. The methods to improve compatibility between polymer and filler are introduced. There are eight methods including silane coupling, Grignard treatment, incorporation of additive, grafting, in situ polymerization, polydopamine coating, particle fusion approach and polymer functionalization. To achieve higher productivity for industrial application, mixed matrix composite membranes are developed. The recent development on hollow fiber and flat mixed matrix composite membrane is reviewed in detail. Last, the future trend of MMM is forecasted.展开更多
In this paper, poly(amide-6-b-ethylene oxide) (Pebax1657)/SAPO-34 mixed matrix membranes (MMMs) were prepared by solvent-evaporation method with acetic acid as a novel solvent. CO2, N2, CH4 and H2 permeation pro...In this paper, poly(amide-6-b-ethylene oxide) (Pebax1657)/SAPO-34 mixed matrix membranes (MMMs) were prepared by solvent-evaporation method with acetic acid as a novel solvent. CO2, N2, CH4 and H2 permeation properties were investigated, and the physical properties of Pebax/SAPO-34 MMMs were characterized by XRD and SEM. At low SAPO-34 content, it was homogeneously distributed in the Pebax ma- trix, and then precipitated and agglomerated at high SAPO-34 content. The crystallinity of Pebax phase in Pebax/SAPO-34 MMMs decreased initially and then rebounded as a result of phase separation. With the increase of transmembrane pressure difference, CO2 permeability was en- hanced due to the effect of pressure-induced plasticization. Owing to the happening of stratification, the CO2 permeability of Pebax/SAPO-34 MMMs (50 wt% SAPO-34) increased to 338 Barrer from 111 Barrer of pristine Pebax, while the selectivities of CO2/CH4 and CO2/N2 were almost unchanged. Compared with the pristine Pebax, the gas separation performances of Pebax/SAPO-34 MMMs were remarkably enhanced.展开更多
The development of multilayer composite membranes for CO_2 separation has gained increasing attention due to the desire for energy efficient technologies. Multilayer composite membranes have many advantages, including...The development of multilayer composite membranes for CO_2 separation has gained increasing attention due to the desire for energy efficient technologies. Multilayer composite membranes have many advantages, including the possibility to optimize membrane materials independently by layers according to their different functions and to reduce the overall transport resistance by using ultrathin selective layers, and less limitations on the material mechanical properties and processability. A comprehensive review is required to capture details of the progresses that have already been achieved in developing multilayer composite membranes with improved CO_2 separation performance in the past 15-20 years.In this review, various composite membrane preparation methods were compared, advances in composite membranes for CO_2/CH_4 separation,CO_2/N_2 and CO_2/H_2 separation were summarized with detailed data, and challenges facing for the CO_2 separation using composite membranes,such as aging, plasticization and long-term stability, were discussed. Finally the perspectives and future research directions for composite membranes were presented.展开更多
Membrane technology has found wide applications in the petrochemical industry, mainly in the purification and recovery of the hydrogen resources. Accurate prediction of the membrane separation performance plays an imp...Membrane technology has found wide applications in the petrochemical industry, mainly in the purification and recovery of the hydrogen resources. Accurate prediction of the membrane separation performance plays an important role in carrying out advanced process control (APC). For the first time, a soft-sensor model for the membrane separation process has been established based on the radial basis function (RBF) neural networks. The main performance parameters, i.e, permeate hydrogen concentration, permeate gas flux, and residue hydrogen concentration, are estimated quantitatively by measuring the operating temperature, feed-side pressure, permeate-side pressure, residue-side pressure, feed-gas flux, and feed-hydrogen concentration excluding flow structure, membrane parameters, and other compositions. The predicted results can gain the desired effects. The effectiveness of this novel approach lays a foundation for integrating control technology and optimizing the operation of the gas membrane separation process.展开更多
In this investigation, polymeric nanocomposite membranes(PNMs) were prepared via incorporating zinc oxide(ZnO) into poly(ether-block-amide)(PEBAX-1074) polymer matrix with different loadings. The neat membrane a...In this investigation, polymeric nanocomposite membranes(PNMs) were prepared via incorporating zinc oxide(ZnO) into poly(ether-block-amide)(PEBAX-1074) polymer matrix with different loadings. The neat membrane and nanocomposite membranes were prepared via solution casting and solution blending methods, respectively. The fabricated membranes were characterized by field emission scanning electron microscopy(FESEM) to survey cross-sectional morphologies and thermal gravimetric analysis(TGA)to study thermal stability. Fourier transform infrared(FT-IR) and X-ray diffraction(XRD) analyses were also employed to identify variations of the chemical bonds and crystal structure of the membranes, respectively. Permeation of pure gases, CO, CHand Nthrough the prepared neat and nanocomposite membranes was studied at pressures of 3–18 bar and temperature of 25 °C. The obtained results showed that the fabricated nanocomposite membranes exhibit better separation performance compared to the neat PEBAX membrane in terms of both permeability and selectivity. As an example, at temperature of 25 °C and pressure of 3 bar, COpermeability, ideal CO/CHand CO/Nselectivity values for the neat PEBAX membrane are 110.67 Barrer, 11.09 and 50.08, respectively, while those values are 152.27 Barrer,13.52 and 62.15 for PEBAX/ZnO nanocomposite membrane containing 8 wt% ZnO.展开更多
Microporous membranes of low-high density polyethylene and their blends were prepared bythermally-induced phase separation of polymer/long-aliphatic chain alcohol (diluent) mixtures.The microstructures of this particu...Microporous membranes of low-high density polyethylene and their blends were prepared bythermally-induced phase separation of polymer/long-aliphatic chain alcohol (diluent) mixtures.The microstructures of this particular membrane, which depends on the diluent properties,polymer concentration and cooling rate, were observed by scanning electron microscopy.'Beehive-type,'leafy-like, and lacy porous structure morphologies can be formed,depending onthe blend composition and phase separation conditions, which were discussed by the polymer anddiluent crystallization processes.展开更多
基金support from Sichuan Science and Technology Program(2021YFH0116)National Natural Science Foundation of China(No.52170112)DongFang Boiler Co.,Ltd.(3522015).
文摘Mixed matrix membranes(MMMs)could combine the advantages of both polymeric membranes and porousfillers,making them an effective alternative to conventional polymer membranes.However,interfacial incompatibility issues,such as the presence of interfacial voids,hardening of polymer chains,and blockage of micropores by polymers between common MMMsfillers and the polymer matrix,currently limit the gas sep-aration performance of MMMs.Ternary phase MMMs(consisting of afiller,an additive,and a matrix)made by adding a third compound,usually functionalized additives,can overcome the structural problems of binary phase MMMs and positively impact membrane separation performance.This review introduces the structure and fabrication processes for ternary MMMs,categorizes various nanofillers and the third component,and summarizes and analyzes in detail the CO_(2) separation performance of newly developed ternary MMMs based on both rubbery and glassy polymers.Based on this separation data,the challenges of ternary MMMs are also discussed.Finally,future directions for ternary MMMs are proposed.
基金supported by The National Key Research and Development Program of China(2021YFB4001204)National Natural Science Foundation of China(22379143)。
文摘Acid loss and plasticization of phosphoric acid(PA)-doped high-temperature polymer electrolyte membranes(HT-PEMs)are critical limitations to their practical application in fuel cells.To overcome these barriers,poly(terphenyl piperidinium)s constructed from the m-and p-isomers of terphenyl were synthesized to regulate the microstructure of the membrane.Highly rigid p-terphenyl units prompt the formation of moderate PA aggregates,where the ion-pair interaction between piperidinium and biphosphate is reinforced,leading to a reduction in the plasticizing effect.As a result,there are trade-offs between the proton conductivity,mechanical strength,and PA retention of the membranes with varied m/p-isomer ratios.The designed PA-doped PTP-20m membrane exhibits superior ionic conductivity,good mechanical strength,and excellent PA retention over a wide range of temperature(80–160°C)as well as satisfactory resistance to harsh accelerated aging tests.As a result,the membrane presents a desirable combination of performance(1.462 W cm^(-2) under the H_(2)/O_(2)condition,which is 1.5 times higher than that of PBI-based membrane)and durability(300 h at 160°C and 0.2 A cm^(-2))in the fuel cell.The results of this study provide new insights that will guide molecular design from the perspective of microstructure to improve the performance and robustness of HT-PEMs.
基金the financial support of the National Key Research and Development Program of China (2020YFB0606405)the Basic Research Program of Shanxi Province (20210302123197)+2 种基金the Key Project of the National Natural Science Foundation of China (21336006)the Scientific Research Foundation for Returned Scholars of Ministry of Education (2017047)the Foundation of State Key Laboratory of Highefficiency Utilization of Coal and Green Chemical Engineering (2017-K15)。
文摘In industry, ethylene(C_(2)H_(4))/propylene(C_(3)H_(6)) separations are usually performed by a cryogenic process,which is energy intensive. Membrane separation technology is an alternative separation process that saves energy and is efficient. In this study, blend membranes were prepared by doping polyethylene glycol(PEG600) into a poly(ether-block-amide)(Pebax^(■) 2533) matrix and were used to separate the C_(2)H_(4)/C_(3)H_(6) mixture. The PEG 600 and Pebax^(■) 2533 polymers have good compatibility because they share hydrogen bonds. The addition of PEG600 is conducive to the hydrophilicity and the free volume of blend membranes, and it is also conducive to the solubility of C_(2)H_(4) and C_(3)H_(6) in the membranes, which improves the ability of the membranes to separate this gas pair. The Pebax^(■) 2533/PEG600 blend membrane with 15%(mass) PEG600 showed the highest separation performance in our investigated membranes, with a C_(3)H_(6)/C_(2)H_(4) selectivity of 8.9 and a C_(3)H_(6) permeability of 196 barrer(1 barrer = 1.33×10^(14)m^(3)(STP)·m·m^(-2)·s^(-1)·kPa^(-1)) at 238 K and 0.2 MPa, which is higher than that of the Pebax^(■) 2533/NaY-6%(mass) membrane(α_(C_(3)H_(6)/C_(2)H_(4)) =6.5, P_(C_(3)H_(6))=211 barrer) reported in our previous work. It is confirmed that incorporating PEG600 into the Pebax^(■) 2533 matrix to fabricate blend membranes is an efficient strategy for separating light olefins.
基金the funding from the National Natural Science Foundation of China (22078107, 22022805)the National Key Research and Development Program (2021YFB3802500)。
文摘During the last decade, metal-organic frameworks(MOFs) have been applied in various fields due to their unique chemical and functional advantages. One of the widespread research hotspots is MOF-based membranes for separations, specifically continuous defect-free MOF membranes, which are usually grown on porous substrates. The substrate not only serves as the MOF layer support but also has a great influence on the membrane fabrication process and the final separation performance of the resultant membrane. In this review, we mainly introduce the progress focused on the substrates for MOF membranes fabrication. The substrate modifications and seeding methods aimed at synthesizing highquality MOF membranes are also summarized systematically.
基金the financial supports that are from the National Natural Science Foundation of China (21921006, U22A20414 and 21938007)the Natural Science Foundation of Jiangsu Province (BK20220002)the open project of the State Key Laboratory of China (KL21-04 and D2021FK055)。
文摘The synthesis of a continuous IMF zeolite membrane was fabricated on tubular substrates by seeded growth for the first time. The straight channels of IMF zeolite with diameters of 0.53–0.59 nm are distinguishable for p-xylene from o-xylene molecules. Pure IMF-phase high-silica IM-5 zeolite seeds with uniform and fine crystal size were fabricated by a new sonication-assisted aging process. The seeds were coated on the support by dipcoating and induced the formation of continuous membrane. Separation performance in p-/o-xylene mixture was investigated at various temperature and pressure. The typical IM-5zeolite membrane had p-/o-xylene separation factor of 3.7. Our results suggest that IM-5 zeolite is a potentially good membrane material for the separation of xylene mixtures.
基金Financial support from the Science Fund for Creative Research Groups of the National Science Foundation of China (22021005)the National Natural Science Foundation of China (21776032)the Innovation Team of Dalian University of Technology (DUT2017TB01)。
文摘Tungsten (W) incorporated mobil-type eleven (MEL) zeolite membrane (referred to as W-MEL membrane) with high separation performance was firstly explored for the separation of oil/water mixtures under the influence of gravity.W-MEL membranes were grown on stainless steel (SS) meshes through in-situ hydrothermal growth method facilitated with (3-aminopropyl)triethoxysilane (APTES) modification of stainless steel meshes,which promote the heterogeneous nucleation and crystal growth of W-MEL zeolites onto the mesh surface.W-MEL membranes were grown on different mesh size supports to investigate the effect of mesh size on the separation performance of the membrane.The assynthesized W-MEL membrane supported on 500 mesh (25μm)(W-MEL-500) exhibit the hydrophilic nature with a water contact angle of 11.8°and delivers the best hexane/water mixture separation with a water flux and separation efficiency of 46247 L·m^(-2)·h^(-1)and 99.5%,respectively.The wettability of W-MEL membranes was manipulated from hydrophilic to hydrophobic nature by chemically modifying with the fluorine-free compounds (hexadecyltrimethoxysilane (HDTMS) and dodecyltrimethoxysilane(DDTMS)) to achieve efficient oil-permselective separation of heavy oils from water.Among the hydrophobically modified W-MEL membranes,W-MEL-500-HDTMS having a water contact angle of146.4°delivers the best separation performance for dichloromethane/water mixtures with a constant oil flux and separation efficiency of 61490 L·m^(-2)·h^(-1)and 99.2%,respectively along with the stability tested up to 20 cycles.Both W-MEL-500-HDTMS and W-MEL-500-DDTMS membranes also exhibit similar separation performances for the separation of heavy oil from sea water along with a 20-fold lower corrosion rate in comparison with the bare stainless-steel mesh,indicating their excellent stability in seawater.Compared to the reported zeolite membranes for oil/water separation,the as-synthesized and hydrophobically modified W-MEL membranes shows competitive separation performances in terms of flux and separation efficiency,demonstrating the good potentiality for oil/water separation.
文摘The aim of this study was to design a new emulsion liquid membrane(ELM)system for the separation of succinic acid from aqueous solutions.The concentration of succinic acid varied from 20 to 60 mmol·L^(-1).The prepared ELM system includes tributylamine(TBA)as a carrier,commercial kerosene as a solvent,Span 80 as a surfactant,and Na2CO3as a stripping agent.In order to control the membrane swelling,different values of cyclohexanone were added to the membrane phase.The effect of various empirical variables on the extraction of the succinic acid such as acid concentration in the feed solution,initial feed concentration,carrier concentration,the stirring speed of the extraction,Na2CO3,surfactant,and cyclohexanone concentrations,and treat ratio in the ELM system.The best result was obtained when TBA was used as the carrier.The final acid extraction efficiency was independent of pH variations of the aqueous feed solution.The extraction of succinic acid solution with a concentration of 40 mmol·L^(-1)was improved by increasing the treat ratio 1:7-1:3,stripping phase concentration 0.5-1.5 mol·L^(-1),stirring speed 300-500 r·min^(-1)and cyclohexanone concentration in the membrane phase 1.2-1.6 mol·L^(-1).No considerable effect on the extraction rate was observed for the carrier concentration in the membrane phase.But,the surfactant concentration in the feed phase showed a dual effect on the extraction efficiency.
基金the financial support provided by the National Natural Science Foundation of China (21808044)。
文摘Nowadays, oil contamination has become a major reason for water pollution, and presents a global environmental challenge. Although many efforts have been devoted to the fabrication of oil/water separation materials, their practical applications are still hindered by their weak durability, poor chemical tolerance,environmental resistance, and potential negative impact on health and the environment. To overcome these drawbacks, this work offers a facile method to fabricate the eco-friendly and durable oil/water separation membrane fabrics by alkaline hydrolysis and silicon polyurethane coating. The X-ray photoelectron spectroscopy, scanning electron microscopy, and atomic force microscopy results demonstrate that silicon polyurethane membrane could be coated onto the surface of hydrolyzed polyester fabric and form a micro-/nano-scaled hierarchical structure. Based on this, the modified fabric could have a stable superhydrophobic property with a water contact angle higher than 150°, even after repeated washing and mechanical abrasion 800 times, as well as chemical corrosion. Moreover, the modified fabrics show excellent oil/water separation efficiency of up to 99% for various types of oil–water mixture. Therefore, this durable, eco-friendly and cost-efficient superhydrophobic fabric has great potential in large-scale oil/water separation.
基金supported by the National Natural Science Foundation of China (52025132, 21621091, 22021001, 22121001, 22275207 and T2241022)the National Science Foundation of Fujian Province of China (2022J02059)+3 种基金the State Key Laboratory of Bio-Fibers and Eco-Textiles (Qingdao University) (KFKT202221)the 111 Project (B17027, B16029)the Science and Technology Projects of Innovation Laboratory for Sciences and Technologies of Energy Materials of Fujian Province (RD2022070601)the Tencent Foundation (The XPLORER PRIZE)。
文摘Membrane separation technology with the ability to regulate gas/liquid transport and separation is critical for environmental fields, such as sewerage treatment, multiphase separation, and desalination. Although numerous membranes can dynamically control liquid-phase fluids transport via external stimuli, the transport and separation of gas-phase fluids remains a challenge. Here, we show a temperature-regulation liquid gating membrane that allows in-situ dynamically controllable gas/liquid transfer and multiphase separation by integrating a thermo-wettability responsive porous membrane with functional gating liquid. Experiments and theoretical analysis have demonstrated the temperature-regulation mechanism of this liquid gating system, which is based on thermo-responsive changes of porous membrane surface polarity, leading to changes in affinity between the porous membrane and the gating liquid. In addition, the sandwich configuration with dense Au-coated surfaces and heterogeneous internal components by a bistable interface design enables the liquid gating system to enhance response sensitivity and maintain working stability. This temperature-regulation gas/liquid transfer strategy expands the application range of liquid gating membranes,which are promising in environmental governance, water treatment and multiphase separation.
基金financially supported by the National Key R&D Program of China(2021YFA1502400)the"Transformational Technologies for Clean Energy and Demonstration"+3 种基金the Strategic Priority Research Program of the Chinese Academy of Sciences(XDA2100000)the National Natural Science Foundation of China(52172005,21905295,22179141)the DNL Cooperation Fund,CAS(DNL202008)the Photon Science Center for Carbon Neutrality and the Major Scientific and Technological Innovation Project of Shandong Province(2020CXGC010402)。
文摘Perovskite-type mixed protonic-electronic conducting membranes have attracted attention because of their ability to separate and purify hydrogen from a mixture of gases generated by industrial-scale steam reforming based on an ion diffusion mechanism.Exploring cost-effective membrane materials that can achieve both high H_(2) permeability and strong CO_(2)-tolerant chemical stability has been a major challenge for industrial applications.Herein,we constructed a triple phase(ceramic-metal-ceramic)membrane composed of a perovskite ceramic phase BaZr_(0.1)Ce_(0.7)Y_(0.1)Yb_(0.1)O_(3-δ)(BZCYYb),Ni metal phase and a fluorite ceramic phase CeO_(2).Under H_(2) atmosphere,Ni metal in-situ exsolved from the oxide grains,and decorated the grain surface and boundary,thus the electronic conductivity and hydrogen separation performance can be promoted.The BZCYYbNi-CeO_(2)hybrid membrane achieved an exceptional hydrogen separation performance of 0.53 mL min^(-1)cm^(-2) at 800℃ under a 10 vol% H_(2) atmosphere,surpassing all other perovskite membranes reported to date.Furthermore,the CeO_(2) phase incorporated into the BZCYYb-Ni effectively improved the CO_(2)-tolerant chemical stability.The BZCYYbNi-CeO_(2) membrane exhibited outstanding long-term stability for at least 80 h at 700℃ under 10 vol%CO_(2)-10 vol%H_(2).The success of hybrid membrane construction creates a new direction for simultaneously improving their hydrogen separation performance and CO_(2) resistance stability.
基金supported by the Excellent Youth Foundation of Henan Scientific Committee,China(222300420018)Key Scientific Research Projects in Universities of Henan Province,China(21zx006)。
文摘Layered assembled membranes of 2D leaf-like zeolitic imidazolate frameworks(ZIF-L)nanosheets have received great attention in the field of water treatment due to the porous structure and excellent antibacterial ability,but the dense accumulation on the membrane surface and the low permeate flux greatly hinder their application.Herein,we synthesized m HNTs(modified halloysite nanotubes)/ZIF-L nanocomposites on modified m HNTs by in situ growth method.Interestingly,due to the different size of m HNTs and ZIF-L,m HNTs were packed in ZIF-L nanosheets.The hollow m HNTs provided additional transport channels for water molecules,and the accumulation of the ZIF-L nanosheets was decreased after assembling m HNTs/ZIF-L nanocomposites into membrane by filtration.The prepared m HNTs/ZIF-L membrane presented high permeate flux(59.6 L·m^(-2)·h^(-1)),which is 2-4 times of the ZIF-L membranes(14.8 L·m^(-2)·h^(-1)).Moreover,m HNTs/ZIF-L membranes are intrinsically antimicrobial,which exhibit extremely high bacterial resistance.We provide a controllable strategy to improve 2D ZIF-L assembles,and develops novel membranes using 2D package structure as building units.
基金supported by the Natural Science Foundation of China(22105129)the Guangdong Basic and Applied Basic Research Foundation(2022A1515011048)the Science and Technology Innovation Commission of Shenzhen(JCYJ20200109105618137)。
文摘With the rapid development of portable technology,lithium batteries have emerged as potential candidates for high-performance energy storage systems owing to their high energy density and cycling stability.Among the key components of a lithium battery system,the separator plays a critical role as it directly influences the battery performance benchmark(cycling performance and safety).However,traditional polyolefin separators(polypropylene/polyethylene)are unable to meet the demands of highperformance and safer battery systems due to their poor electrolyte compatibility,thermal runaways,and ultimate growth of dendrites.In contrast,membranes fabricated using polybenzimidazole(PBI)exhibit excellent electrolyte wettability and outstanding thermal dimensional stability,thus holding great potential as separators for high-performance and high-safety batteries.In this paper,we present a comprehensive review of the general requirements for separators,synthesis technology for separators,and research trends focusing PBI membranes in lithium batteries to alleviate the current commercial challenges faced by conventional polyolefin separators.In addition,we discuss the future development direction for PBI battery separators by considering various factors such as production cost,ecological footprint,preparation technology,and battery component compatibility.By exploring these perspectives,we aim to promote the continued application and exploration of PBI-based materials to advance lithium battery technology.
基金supported by the National Research Foundation of Korea(NRF)grant funded by the Korean government MSIT(2021R1A2C2093358,2021R1A4A3027878,2022M3I3A1081901)financial support from the Lotte Chemical Company。
文摘Cu catalysts can convert CO_(2) through an electrochemical reduction reaction into a variety of useful carbon-based products.However,this capability provides an obstacle to increasing the selectivity for a single product.Herein,we report a simple fabrication method for a Cu-Pd alloy catalyst for use in a membrane electrode assembly(MEA)-based CO_(2) electrolyzer for the electrochemical CO_(2) reduction reaction(ECRR)with high selectivity for CO production.When the composition of the Cu-Pd alloy catalyst was fabricated at 6:4,the selectivity for CO increased and the production of multi-carbon compounds and hydrogen is suppressed.Introducing a Cu-Pd alloy catalyst with 6:4 ratio as the cathode of the MEAbased CO_(2) electrolyzer showed a CO faradaic efficiency of 92.8%at 2.4 V_(cell).We assumed that these results contributed from the crystal planes on the surface of the Cu-Pd alloy.The phases of the Cu-Pd alloy catalyst were partially separated through annealing to fabricate a catalyst with high selectivity for CO at low voltage and C_(2)H_4 at high voltage.The results of CO-stripping testing confirmed that when Cu partially separates from the lattice of the Cu-Pd alloy,the desorption of~*CO is suppressed,suggesting that C-C coupling reaction is favored.
文摘Hydrogen is an alternative energy source that has the potential to replace fossil fuels.One of the hydrogen applications is as a material for Polymer Electrolyte Membrane Fuel Cells(PEMFC)in fuel cell vehicles.High-purity hydrogen can be obtained using a hydrogen separation membrane to prevent unwanted contaminants from potentially harming the PEMFC components.In this study,we fabricated a plasma membrane reactor and investigated the permeation performance of a hydrogen separation membrane in a plasma membrane reactor utilizing atmospheric pressure plasma.The result showed the hydrogen permeation rate increasing with time as reactor temperature is increased through joule heating.By decreasing the gap length of the reactor from 2 to 1 mm,the hydrogen permeation rate increases by up to 40%.The hydrogen permeation rate increases by 30%when pressure is applied to the plasma membrane reactor by up to 100 kPa.
基金Supported by the National Natural Science Foundation of China(21436009)the Program of Introducing Talents of Discipline to Universities(B06006)
文摘Recent advances on mixed matrix membrane for CO_2 separation are reviewed in this paper. To improve CO_2 separation performance of polymer membranes, mixed matrix membranes(MMMs) are developed. The concept of MMM is illustrated distinctly. Suitable polymer and inorganic or organic fillers for MMMs are summarized.Possible interface morphologies between polymer and filler, and the effect of interface morphologies on gas transport properties of MMMs are summarized. The methods to improve compatibility between polymer and filler are introduced. There are eight methods including silane coupling, Grignard treatment, incorporation of additive, grafting, in situ polymerization, polydopamine coating, particle fusion approach and polymer functionalization. To achieve higher productivity for industrial application, mixed matrix composite membranes are developed. The recent development on hollow fiber and flat mixed matrix composite membrane is reviewed in detail. Last, the future trend of MMM is forecasted.
基金supported by the National Science and Technology Planning Project(No.2011BAC08B00)the National High Technology Research and Development Program of China(863 Program)(No.2012AA03A611)
文摘In this paper, poly(amide-6-b-ethylene oxide) (Pebax1657)/SAPO-34 mixed matrix membranes (MMMs) were prepared by solvent-evaporation method with acetic acid as a novel solvent. CO2, N2, CH4 and H2 permeation properties were investigated, and the physical properties of Pebax/SAPO-34 MMMs were characterized by XRD and SEM. At low SAPO-34 content, it was homogeneously distributed in the Pebax ma- trix, and then precipitated and agglomerated at high SAPO-34 content. The crystallinity of Pebax phase in Pebax/SAPO-34 MMMs decreased initially and then rebounded as a result of phase separation. With the increase of transmembrane pressure difference, CO2 permeability was en- hanced due to the effect of pressure-induced plasticization. Owing to the happening of stratification, the CO2 permeability of Pebax/SAPO-34 MMMs (50 wt% SAPO-34) increased to 338 Barrer from 111 Barrer of pristine Pebax, while the selectivities of CO2/CH4 and CO2/N2 were almost unchanged. Compared with the pristine Pebax, the gas separation performances of Pebax/SAPO-34 MMMs were remarkably enhanced.
基金supported by the Research Council of Norway through the CLIMIT program(MCIL-CO_2 project,215732)the European Union Seventh Framework Programme(FP7/2007-2013)in HiPerCap project under grant agreement n°608555
文摘The development of multilayer composite membranes for CO_2 separation has gained increasing attention due to the desire for energy efficient technologies. Multilayer composite membranes have many advantages, including the possibility to optimize membrane materials independently by layers according to their different functions and to reduce the overall transport resistance by using ultrathin selective layers, and less limitations on the material mechanical properties and processability. A comprehensive review is required to capture details of the progresses that have already been achieved in developing multilayer composite membranes with improved CO_2 separation performance in the past 15-20 years.In this review, various composite membrane preparation methods were compared, advances in composite membranes for CO_2/CH_4 separation,CO_2/N_2 and CO_2/H_2 separation were summarized with detailed data, and challenges facing for the CO_2 separation using composite membranes,such as aging, plasticization and long-term stability, were discussed. Finally the perspectives and future research directions for composite membranes were presented.
文摘Membrane technology has found wide applications in the petrochemical industry, mainly in the purification and recovery of the hydrogen resources. Accurate prediction of the membrane separation performance plays an important role in carrying out advanced process control (APC). For the first time, a soft-sensor model for the membrane separation process has been established based on the radial basis function (RBF) neural networks. The main performance parameters, i.e, permeate hydrogen concentration, permeate gas flux, and residue hydrogen concentration, are estimated quantitatively by measuring the operating temperature, feed-side pressure, permeate-side pressure, residue-side pressure, feed-gas flux, and feed-hydrogen concentration excluding flow structure, membrane parameters, and other compositions. The predicted results can gain the desired effects. The effectiveness of this novel approach lays a foundation for integrating control technology and optimizing the operation of the gas membrane separation process.
文摘In this investigation, polymeric nanocomposite membranes(PNMs) were prepared via incorporating zinc oxide(ZnO) into poly(ether-block-amide)(PEBAX-1074) polymer matrix with different loadings. The neat membrane and nanocomposite membranes were prepared via solution casting and solution blending methods, respectively. The fabricated membranes were characterized by field emission scanning electron microscopy(FESEM) to survey cross-sectional morphologies and thermal gravimetric analysis(TGA)to study thermal stability. Fourier transform infrared(FT-IR) and X-ray diffraction(XRD) analyses were also employed to identify variations of the chemical bonds and crystal structure of the membranes, respectively. Permeation of pure gases, CO, CHand Nthrough the prepared neat and nanocomposite membranes was studied at pressures of 3–18 bar and temperature of 25 °C. The obtained results showed that the fabricated nanocomposite membranes exhibit better separation performance compared to the neat PEBAX membrane in terms of both permeability and selectivity. As an example, at temperature of 25 °C and pressure of 3 bar, COpermeability, ideal CO/CHand CO/Nselectivity values for the neat PEBAX membrane are 110.67 Barrer, 11.09 and 50.08, respectively, while those values are 152.27 Barrer,13.52 and 62.15 for PEBAX/ZnO nanocomposite membrane containing 8 wt% ZnO.
文摘Microporous membranes of low-high density polyethylene and their blends were prepared bythermally-induced phase separation of polymer/long-aliphatic chain alcohol (diluent) mixtures.The microstructures of this particular membrane, which depends on the diluent properties,polymer concentration and cooling rate, were observed by scanning electron microscopy.'Beehive-type,'leafy-like, and lacy porous structure morphologies can be formed,depending onthe blend composition and phase separation conditions, which were discussed by the polymer anddiluent crystallization processes.