Optimization of micro milling electrical discharge machining of Inconel 718 by Grey-Taguchi method

The optimization of micro milling electrical discharge machining（EDM） process parameters of Inconel 718 alloy to achieve multiple performance characteristics such as low electrode wear,high material removal rate and low working gap was investigated by the Grey-Taguchi method.The influences of peak current,pulse on-time,pulse off-time and spark gap on electrode wear（EW）,material removal rate（MRR） and working gap（WG） in the micro milling electrical discharge machining of Inconel 718 were analyzed.The experimental results show that the electrode wear decreases from 5.6×10-9 to 5.2×10-9 mm3/min,the material removal rate increases from 0.47×10-8 to 1.68×10-8 mm3/min,and the working gap decreases from 1.27 to 1.19 μm under optimal micro milling electrical discharge machining process parameters.Hence,it is clearly shown that multiple performance characteristics can be improved by using the Grey-Taguchi method.

Comparative study on discharge conditions in micro-hole electrical discharge machining of tungsten carbide (WC-Co) material

WC-Co is used widely in die and mold industries due to its unique combination of hardness, strength and wear-resistance. For machining difficult-to-cut materials, such as tungsten carbide, micro-electrical discharge machining(EDM) is one of the most effective methods for making holes because the hardness is not a dominant parameter in EDM. This paper describes the characteristics of the discharge conditions for micro-hole EDM of tungsten carbide with a WC grain size of 0.5 μm and Co content of 12%. The EDM process was conducted by varying the condenser and resistance values. A R-C discharge EDM device using arc erosion for micro-hole machining was suggested. Furthermore, the characteristics of the developed micro-EDM were analyzed in terms of the electro-optical observation using an oscilloscope and field emission scanning electron microscope.

Micro Electrical Discharge Machining Deposition in Air for Fabrication of Micro Spiral Structures

Micro electrical discharge machining（EDM） deposition process is a new micro machining method for fabrication of metal micro structures. In this process, the high level of tool electrode wear is used to achieve the metal material deposition. Up to now, the studies of micro EDM deposition process focused mainly on the researches of deposition process, namely the effects of discharge parameters in deposition process on the deposition rate or deposition quality. The research of the formation of micro structures with different discharge energy density still lacks. With proper conditions and only by the z-axis feeding in vertical direction, a novel shape of micro spiral structure can be deposited, with 0.11 mm in wire diameter, 0.20 mm in outside diameter, and 3.78 mm in height. Then some new deposition strategies including angular deposition and against the gravity deposition were also successful. In order to find the forming mechanism of the spiral structures, the numerical simulation of the transient temperature distribution on the discharge point was conducted by using the finite-element method（FEM）. The results show that there are two major factors lead to the forming of the spiral structures. One is the different material removal form of tool electrode according with the discharge energy density, the other is the influenced degree of the movement of the removed material particles in the discharge gap. The more the energy density in single discharge is, the smaller the mass of the removed material particles is, and the easier the movements of which will be changed to form an order tendency. The fine texture characteristics of the deposited micro spiral structures were analyzed by the energy spectrum analysis and the metallographic analysis. It shows that the components of the deposited material are almost the same as those of the tool electrode. Moreover the deposited material has the brass metallic luster in the longitudinal profile and has compact bonding with the base material. This research is useful to understand the micro-process of micro EDM deposition better and helpful to increase the controllability of the new EDM method for fabrication of micro structures.

Experimental Research on Effects of Process Parameters on Servo Scanning 3D Micro Electrical Discharge Machining

Servo scanning 3D micro electrical discharge machining (3D SSMEDM) is a novel and effective method in fabricating complex 3D micro structures with high aspect ratio on conducting materials. In 3D SSMEDM process, the axial wear of tool electrode can be compensated automatically by servo-keeping discharge gap, instead of the traditional methods that depend on experiential models or intermittent compensation. However, the effects of process parameters on 3D SSMEDM have not been reported up until now. In this study, the emphasis is laid on the effects of pulse duration, peak current, machining polarity, track style, track overlap, and scanning velocity on the 3D SSMEDM performances of machining efficiency, processing status, and surface accuracy. A series of experiments were carried out by machining a micro-rectangle cavity (900 μm×600 μm) on doped silicon. The experimental results were obtained as follows. Peak current plays a main role in machining efficiency and surface accuracy. Pulse duration affects obviously the stability of discharge state. The material removal rate of cathode processing is about 3/5 of that of anode processing. Compared with direction-parallel path, contour-parallel path is better in counteracting the lateral wear of tool electrode end. Scanning velocity should be selected moderately to avoid electric arc and short. Track overlap should be slightly less than the radius of tool electrode. In addition, a typical 3D micro structure of eye shape was machined based on the optimized process parameters. These results are beneficial to improve machining stability, accuracy, and efficiency in 3D SSMEDM.

Micro electrical discharge machining of small hole in TC4 alloy

Aiming at machining deeply small holes in TC4 alloy,a series of experiments were carried out on a self-developed multi-axis micro electrical discharge machining(micro-EDM)machine tool.To improve machining efficiency and decrease relative wear of electrode in machining deeply small hole in TC4 alloy,many factors in micro-EDM,such as polarity,electrical parameters and supplying ways of working fluid were studied.Experimental results show that positive polarity machining is far superior to negative polarity machining;it is more optimal when open-circuit voltage,pulse width and pulse interval are 130 V,5μs and 15μs respectively on the self developed multi-axis micro-EDM machine tool;when flushing method is applied in micro-EDM,the machining efficiency is higher and relative wear of electrode is smaller.

Scale Effects and a Method for Similarity Evaluation in Micro Electrical Discharge Machining

Electrical discharge machining（EDM） is a promising non-traditional micro machining technology that offers a vast array of applications in the manufacturing industry. However, scale effects occur when machining at the micro-scale, which can make it difficult to predict and optimize the machining performances of micro EDM. A new concept of ＂scale effects＂ in micro EDM is proposed, the scale effects can reveal the difference in machining performances between micro EDM and conventional macro EDM. Similarity theory is presented to evaluate the scale effects in micro EDM. Single factor experiments are conducted and the experimental results are analyzed by discussing the similarity difference and similarity precision. The results show that the output results of scale effects in micro EDM do not change linearly with discharge parameters. The values of similarity precision of machining time significantly increase when scaling-down the capacitance or open-circuit voltage. It is indicated that the lower the scale of the discharge parameter, the greater the deviation of non-geometrical similarity degree over geometrical similarity degree, which means that the micro EDM system with lower discharge energy experiences more scale effects. The largest similarity difference is 5.34 while the largest similarity precision can be as high as 114.03. It is suggested that the similarity precision is more effective in reflecting the scale effects and their fluctuation than similarity difference. Consequently, similarity theory is suitable for evaluating the scale effects in micro EDM. This proposed research offers engineering values for optimizing the machining parameters and improving the machining performances of micro EDM.

Material properties and machining performance of hybrid Ti_2AlN bulk material for micro electrical discharge machining

Mn+1AXn(MAX) phases are a family of nanolaminated compounds that possess unique combination of typical ceramic properties and typical metallic properties.As a member of MAX phase,Ti2 AlN bulk materials are attractive for some high-temperature applications.The synthesis,characteristics and machining performance of hybrid Ti2 AlN bulk materials were focused on in this work.The bulk samples mainly consisting of Ti2 AlN MAX phase with density close to theoretic one were synthesized by a spark plasma sintering method.Scanning electron microscopy results indicate homogenous distribution of Ti2 AlN grains in the samples.Micro-hardness values are almost constant under different loads (6-6.5 GPa).A machining test was carried out to compare the effect of material properties on micro-electrical discharge machining (micro-EDM) performance for Ti2 AlN bulk samples and Ti6242 alloy.The machining performance of the Ti2 AlN sample is better than that of the Ti6242 alloy.The inherent mechanism was discussed by considering their electrical and thermal conductivity.

Development of micro wire electrical discharge machining platform and its application

A machining platform of micro wire electrical discharge machining (MWEDM) was developed. The key technology of MWEDM mainly includes granite basement, micro energy pulse generator, detection and servo control system, constant tension winding system and V-block guide wire mechanism. Utilizing micro wire electrode with 30μm in diameter, the MWEDM can machine the micro slot with the minimum size of 38μm wide, and the surface roughness is smaller than 0.1μm, the machining precision is less than 0.5μm, the white layer is no more than 2μm with main cut. All kinds of complex micro parts, such as micro gear, micro bearing bracket and micro shaped holes, can also be machined by using this platform.

Fabrication of Micro Structures by Ultrashort Voltage Pulse Electrical Discharge Machining

The machining of small holes and array holes has been a difficult problem in machining field. Tiny hole is widely used in mechanical field, for instance, fuel injection nozzles, spinneret holes for synthetic fibers and wire drawing dies. This paper investigated the application of EDM (electrical discharge machining) to the fabrication of micro structures. There are obvious limitations in the process of micro-electrical discharge machining, such as electrode wear, unstable discharge condition and low machining efficiency. The effects of EDM parameters were investigated, such as voltage, pulse frequency, and frequency of ultrasonic vibration applied to electrode. Micro holes were machined with Pt electrode made by focused-ion-beam chemical vapor deposition (FIB-CVD) and Cu electrode made by wire-electrode cutting. The comparison experiments between EDM and ECM (electrochemical machining) indicated that the processing of ECM has serious stray current corrosion and poor machining precision. Moreover, the workpiece vibration was firstly proposed to be utilized in the micro-electrical discharge machining. It can be concluded that maximum machine could be obtained under the amplitude ratio of 76%, which was an appropriate parameter.

Surface Modification Process by Electrical Discharge Machining with Ti Powder Green Compact Electrode

This paper describes a new method of surface modification by Electrical Discharge Machining (EDM). By using ordinary EDM machine tool and kerosene fluid, a hard ceramic layer can be created on the workpiece surface with Ti or other compressed powder electrode in a certain condition. This new revolutionary method is called Electrical Discharge Coating (EDC). The process of EDC begins with electrode wear during EDM,then a kind of hard carbide is created through the thermal and chemical reaction between the worn electrode material and the carbon particle decomposed from kerosene fluid under high temperature. The carbide is piled up on a workpiece quickly and becomes a hard layer of ceramic about 20 μm in several minutes. This paper studies the principle and process of EDC systemically by using Ti powder green compact electrode. In order to obtain a layer of compact ceramic film, it is very important to select proper electric pulse parameters, such as pulse width, pulse interval, peak current. Meantime, the electrode materials and its forming mode will effect the machining surface quality greatly. This paper presents a series of experiment results to study the EDC process by adopt different technology parameters. Experiments and analyses show that a compact TiC ceramic layer can be created on the surface of metal workpiece. The hardness of ceramic layer is more 3 times higher than the base body, and the hardness changes gradiently from surface to base body. The method will have a great future because many materials can be easily added to the electrode and then be coated on the workpiece surface. Gearing the parameters ceramic can be created with different thickness. The switch between deposition and removal process is carried out easily by changing the polarity, thus the gear to the thickness and shape of the composite ceramic layer is carried out easily. This kind of composite ceramic layer will be used to deal with the surface of the cutting tools or molds possibly, in order to lengthen their life. It also can be found wide application in the fields of surface repairing and strengthening of the ship or aircraft.

Parameter optimization model in electrical discharge machining process

Electrical discharge machining (EDM) process, at present is still an experience process, wherein selected parameters are often far from the optimum, and at the same time selecting optimization parameters is costly and time consuming. In this paper, artificial neural network (ANN) and genetic algorithm (GA) are used together to establish the parameter optimization model. An ANN model which adapts Levenberg-Marquardt algorithm has been set up to represent the relationship between material removal rate (MRR) and input parameters, and GA is used to optimize parameters, so that optimization results are obtained. The model is shown to be effective, and MRR is improved using optimized machining parameters.

Machining performance on hybrid process of abrasive jet machining and electrical discharge machining

To develop a hybrid process of abrasive jet machining (AJM) and electrical discharge machining (EDM),the effects of the hybrid process parameters on machining performance were comprehensively investigated to confirm the benefits of this hybrid process.The appropriate abrasives delivered by high speed gas media were incorporated with an EDM in gas system to construct the hybrid process of AJM and EDM,and then the high speed abrasives could impinge on the machined surface to remove the recast layer caused by EDM process to increase the efficiency of material removal and reduce the surface roughness.In this study,the benefits of the hybrid process were determined as the machining performance of hybrid process was compared with that of the EDM in gas system.The main process parameters were varied to explore their effects on material removal rate,surface roughness and surface integrities.The experimental results show that the hybrid process of AJM and EDM can enhance the machining efficiency and improve the surface quality.Consequently,the developed hybrid process can fit the requirements of modern manufacturing applications.

Electrical discharge machining of 6061 aluminium alloy

The wire electrical discharge machining（EDM） of 6061 aluminium alloy in terms of material removal rate,kerf/slit width,surface finish and wear of electrode wire for different pulse on time and wire tension was studied.Eight experiments were carried out in a wire EDM machine by varying pulse on time and wire tension.It is found that the material removal rate increases with the increase of pulse on time though the wire tension does not affect the material removal rate.It seems that the higher wire tension facilitates steady machining process,which generates low wear in wire electrode and better surface finish.The surface roughness does not change notably with the variation of pulse on time.The appearance of the machined surfaces is very similar under all the machining conditions.The machined surface contains solidified molten material,splash of materials and blisters.The increase of the pulse on time increases the wear of wire electrode due to the increase of heat input.The wear of wire electrode generates tapered slot which has higher kerf width at top side than that at bottom side.The higher electrode wear introduces higher taper.

Surface performance of workpieces processed by electrical discharge machining in gas

The surface performance of workpieces processed by electrical discharge machining in gas(dry EDM)was studied in this paper.Firstly,the composition,micro hardness and recast layer of electrical discharge machined(EDMed)surface of 45 carbon steels in air were investigated through different test analysis methods.The results show that the workpiece surface EDMed in air contains a certain quantity of oxide,and oxidation occurs on the workpiece surface.Compared with the surface of workpieces processed in kerosene,fewer cracks exist on the dry EDMed workpiece surface,and the surface recast layer is thinner than that obtained by conventional EDM.The micro hardness of workpieces machined by dry EDM method is lower than that machined in kerosene,and higher than that of the matrix.In addition,experiments were conducted on the surface wear resistance of workpieces processed in air and kerosene using copper electrode and titanium alloy electrode.The results indicate that the surface wear resistance of workpieces processed in air can be improved,and it is related with tool material and dielectric.

Integrated CAD/CAPP/CAM system for electric discharge machining

An integrated CAD/CAPP/CAM system modeling for Electric Discharge Machining (EDM) is constructed on the basis of an integrated engineering database. EDM feature objects are developed using the object oriented database provided by AutoCAD R14, and EDM feature modeling is realized in AutoCAD environments.

Modelling effect of magnetic field on material removal in dry electrical discharge machining

One of the reasons for increased material removal rate in magnetic field assisted dry electrical discharge machining （EDM） is confinement of plasma due to Lorentz forces. This paper presents a mathematical model to evaluate the effect of external magnetic field on crater depth and diameter in single- and multiple-discharge EDM process. The model incorporates three main effects of the magnetic field, which include plasma confinement, mean free path reduction and pulsating magnetic field effects. Upon the application of an external magnetic field, Lorentz forces that are developed across the plasma column confine the plasma column. Also, the magnetic field reduces the mean free path of electrons due to an increase in the plasma pressure and cycloidal path taken by the electrons between the electrodes. As the mean free path of electrons reduces, more ionization occurs in plasma column and eventually an increase in the current density at the inter-electrode gap occurs. The model results for crater depth and its diameter in single discharge dry EDM process show an error of 9%-10% over the respective experimental values.

A Study on Modelling Surface Finish in Electrical Discharge Machining Tablet Shape Punches Using Response Surface Methodology

This paper introduces a study on modelling surface finish in EDM （Electrical Discharge Machining） of tablet shape punches when using copper as electrode material. In this study, 27 experiments were performed based on BBD （Box-Behnken Design） and the work-piece material was 9CrSi steel. The input process parameters were the current, the pulse on time, the pulse off time and the voltage. The effects of the input parameters on the surface finish were evaluated by analysing variance. Besides, from the results of the experiments, a regression equation for determining the surface roughness is introduced. Also, the optimum input parameter values were found in order to get the minimum surface roughness.

Review on non-conventional machining of shape memory alloys

Shape memory alloys （SMAs） are the developing advanced materials due to their versatile specific properties such as pseudoelasticity, shape memory effect （SME）, biocompatibility, high specific strength, high corrosion resistance, high wear resistance and high anti-fatigue property. Therefore, the SMAs are used in many applications such as aerospace, medical and automobile. However, the conventional machining of SMAs causes serious tool wear, time consuming and less dimensional deformity due to severe strain hardening and pseudoelasticity. These materials can be machined using non-conventional methods such as laser machining, water jet machining （WJM） and electrochemical machining （ECM）, but these processes are limited to complexity and mechanical properties of the component. Electrical discharge machining （EDM） and wire EDM （WEDM） show high capability to machine SMAs of complex shapes with precise dimensions. The aim of this work is to present the consolidated references on the machining of SMAs using EDM and WEDM and subsequently identify the research gaps. In support to these research gaps, this work has also evolved the future research directions.

电火花加工金刚石-镍复合电极制备参数优化研究

研究了化学复合镀镀液的制备参数对复合电极制备的影响,阐述了金刚石微粉预处理步骤。分析了金刚石微粉的等效粒径对复合电极镀层的影响,得出最佳镀层金刚石等效粒径为10μm。进行了镀液温度变化下的复合电极制备速度关系试验,得出最佳制备温度为74~76℃。对制备的电极进行加工试验,结果表明:参数优化复合电极的电极角损耗比普通紫铜电极降低了74.74%;参数优化复合电极的电极角损耗比参数未优化复合电极降低了57.29%。

Trajectory optimisation in electrical discharge machining of three-dimensional curved and twisted channels

Numerical control electrical discharge machining(NC EDM) is one of the most widely used machining technologies for manufacturing a closed blisk flow path, particularly for three-dimensional(3D) curved and twisted flow channels. In this process, tool electrode design and machining trajectory planning are the key factors affecting machining accessibility and efficiency. Herein, to reduce the difficulty in designing the electrode and its motion path in the closed curved and twisted channels, a heuristic search hybrid optimisation strategy based on channel grids is adopted to realise the initial electrode trajectory design search and optimised size reduction. By transferring the trajectory optimisation constraints from the complex free-form surface to numbered grids, the search is found to be more orderly and accurate. The two trajectory indicators, namely argument angle and minimum distance, are analysed separately for the optimised results of the adaptive learning particle swarm optimisation algorithm, demonstrating that they can meet the actual processing requirements.Experimental results of NC EDM indicate that the motion path generated by this design method can meet the machining requirements of 3D curved and twisted flow channels.