Design of 32 kbit one-time programmable memory for microcontroller units

A 32 kbit OTP(one-time programmable)memory for MCUs(micro-controller units)used in remote controllers was designed.This OTP memory is used for program and data storage.It is required to apply 5.5V to BL(bit-line)and 11V to WL(word-line)for a OTP cell of 0.35μm ETOX(EEPROM tunnel oxide)type by MagnaChip.We use 5V transistors on column data paths to reduce the area of column data paths since they require small areas.In addition,we secure device reliability by using HV(high-voltage)transistors in the WL driver.Furthermore,we change from a static logic to a dynamic logic used for the WL driver in the core circuit.Also,we optimize the WD(write data)switch circuit.Thus,we can implement them with a small-area design.In addition,we implement the address predecoder with a small-area logic circuit.The area of the designed 32 kbit OTP with 5V and HV devices is 674.725μm×258.75μm(=0.1745mm2)and is 56.3% smaller than that using 3.3V devices.

Application of Total Least Square Algorithm in Static Decoupling of NGMIMU

The linear coupling of Non-gyro Micro Inertial Measurement Unit (NGMIMU) is akind of system error that affects the accuracy of measurement seriously. In this article, theauthor puts forward a new linear decoupling algorithm which simultaneously considers the error ofstandard input signal and output of accelerators when the coupling parameters are calculated. TheTotal Least Square (TLS) solutions of coupling parameters own the minimum characteristic to theinput and output values. Then these parameters are used to reconstruct the outputs of acceleratorsso as to realize the decoupling. The emulation result show that the ratio of decoupling error isless than 8 percent and verify the feasibility of this algorithm.

Technical Research for Detector of Grain Moisture Content Based on Error Compensation

According to the existing method including testing the frequency and establishing the relationship between moisture content and frequency, a corresponding instrument was designed. In order to further improve the accuracy and rapidity of the system, a new approach to describe the relationship between the measurement error and the temperature was proposed. The error band could be obtained and divided into several parts（based on the range of temperature） to indicate the error value that should compensate the grain moisture content for the changes in temperature. By calculating the error band at the maximum and the minimum operating temperatures, as well as by determining the error compensation value from the error band based on the measurement moisture content, the final effective result was derived.

Decentralized and overall condition monitoring system for large-scale mobile and complex equipment

It is an urgent project to realize online and overall condition monitoring and timely fault diagnosis for large-scale mobile and complex equipment. Moreover, most of the existing large-scale complex equipment has quite insufficient accessibility of examination, although it still has quite a long service life. The decentralized and overall condition monitoring, as a new concept, is proposed from the point of view of the whole system. A set of complex equipment is divided into several parts in terms of concrete equipment. Every part is processed via one detecting unit, and the main detecting unit is connected with other units. The management work and communications with the remote monitoring center have been taken on by it. Consequently, the difficulty of realizing a condition monitoring system and the complexity of processing information is reduced greatly. Furthermore, excellent maintainability of the condition monitoring system is obtained because of the modularization design. Through an application example, the design and realization of the decentralized and overall condition monitoring system is introduced specifically. Some advanced technologies, such as, micro control unit （MCU）, advanced RISC machines （ARM）, and control area network （CAN）, have been adopted in the system. The system＇s applicability for the existing large-scale mobile and complex equipment is tested.

Microminiature Inertial Measurement System and Its Applications

The microminiature inertial measurement system, a new style of inertial measurement system, has many advantages compared with traditional systems, such as small size, low mass, low cost, low power consumption, high bearing capacity, and long life. Undoubtedly, it will have wide applications in military and commercial fields. However, current micro inertial sensors do not have sufficient accuracy, so, its applications are limited to some extent. This paper describes a microminiature inertial measurement system and its design, operating theory and error control techniques. In addition, its performance and applications are evaluated.