Room temperature low threshold lasing of green GaNbased vertical cavity surface emitting laser(VCSEL)was demonstrated under continuous wave(CW)operation.By using self-formed InGaN quantum dots(QDs)as the active region...Room temperature low threshold lasing of green GaNbased vertical cavity surface emitting laser(VCSEL)was demonstrated under continuous wave(CW)operation.By using self-formed InGaN quantum dots(QDs)as the active region,the VCSEL emitting at 524.0 nm has a threshold current density of 51.97 A cm^(-2),the lowest ever reported.The QD epitaxial wafer featured with a high IQE of 69.94%and theδ-function-like density of states plays an important role in achieving low threshold current.Besides,a short cavity of the device(~4.0λ)is vital to enhance the spontaneous emission coupling factor to 0.094,increase the gain coefficient factor,and decrease the optical loss.To improve heat dissipation,AlN layer was used as the current confinement layer and electroplated copper plate was used to replace metal bonding.The results provide important guidance to achieving high performance GaN-based VCSELs.展开更多
The aerospace and military sectors have widely used AA7075, a type of 7075 aluminum alloy, due to its exceptional mechanical performance. Selective laser melting (SLM) is a highly effective method for producing intric...The aerospace and military sectors have widely used AA7075, a type of 7075 aluminum alloy, due to its exceptional mechanical performance. Selective laser melting (SLM) is a highly effective method for producing intricate metallic components, particularly in the case of aluminum alloys like Al-Si-Mg. Nevertheless, the production of high-strength AA7075 by SLM is challenging because of its susceptibility to heat cracking and elemental vaporization. In this study, AA7075 powders were mechanically mixed with SiC and TiC particles. Subsequently, this new type of AA7075 powder was effectively utilized in green laser printing to create solid components with fine-grain strengthening microstructures consisting of equiaxial grains. These as-printed parts exhibit a tensile strength of up to 350 MPa and a ductility exceeding 2.1%. Hardness also increases with the increasing content of mixed powder, highlighting the essential role of SiC and TiC in SLM for improved hardness and tensile strength performance. .展开更多
The inhomogeneous broadening parameter and the internal loss of green LDs are determined by experiments and theoretical fitting. It is found that the inhomogeneous broadening plays an important role on the threshold c...The inhomogeneous broadening parameter and the internal loss of green LDs are determined by experiments and theoretical fitting. It is found that the inhomogeneous broadening plays an important role on the threshold current density of green LDs. The green LD with large inhomogeneous broadening even cannot lase. Therefore, reducing inhomogeneous broadening is a key issue to improve the performance of green LDs.展开更多
We successfully obtain a high-average-power high-stability Q-switched green laser based on diode-side-pumped composite ceramic Nd：YAG in a straight piano-concave cavity. The temperature distribution in composite cera...We successfully obtain a high-average-power high-stability Q-switched green laser based on diode-side-pumped composite ceramic Nd：YAG in a straight piano-concave cavity. The temperature distribution in composite ceramic Nd：YAG crystal is numerically analyzed and compared with that of conventional Nd：YAG crystal. By using a composite ceramic Nd：YAG rod and a type-II high gray track resistance KTP （HGTR-KTP） crystal, a green laser with an average output power of 165 W is obtained at a repetition rate of 25 kHz, with a diode-to-green optical conversion of 14.68%, and a pulse width of 162 ns. To the best of our knowledge, both the output power and optical-to-optical efficiency are the highest values for green laser systems with intracavity frequency doubling of this novel composite ceramic Nd：YAG laser to date. The power fluctuation at around 160 W is lower than 0.3% in 2.5 hours.展开更多
We first experimentally demonstrate a laser-diode end-pumped self-Q-switched and mode-locked Nd,Cr：YAG green laser with a KTP crystal as the intra-cavity frequency doubler. The device produces an average output power...We first experimentally demonstrate a laser-diode end-pumped self-Q-switched and mode-locked Nd,Cr：YAG green laser with a KTP crystal as the intra-cavity frequency doubler. The device produces an average output power of 680 mW at 532 nm. The corresponding pulse width of the Q-switched envelope of the green laser is 170 ＋ 20 ns. The mode-locked pulses have a repetition rate of approximately 183 MHz and the average pulse duration is estimated to be around sub-nanosecond. It is found that the intra-cavity frequency doubling greatly improves the modulation depth and stability of the mode-locked pulses within the Q-switched envelope.展开更多
The possible ways and progress of infrared or red laser pumped green and blue laser emissions from a single solid state material doped by rare earth ions are outlined. The green and blue lasers realized from infrared ...The possible ways and progress of infrared or red laser pumped green and blue laser emissions from a single solid state material doped by rare earth ions are outlined. The green and blue lasers realized from infrared laser pumped rare earth doped nonlinear laser crystals by means of self frequency conversion and from infrared laser pumped rare earth doped bulk, fiber and microsphere materials by means of frequency upconversion are introduced in detail. Other kinds of devices and methods are also compared. The typical nonlinear laser crystals such as YAl 3(BO 3) 4, GdAl 3(BO 3) 4, YCa 4O(BO 3) 3 , GdCa 4O(BO 3) 3, and the typical upconversion fluoride fibers are compared and analyzed. The major problems remaining to be solved and the developing trends in the area are also discussed.展开更多
A laser diode (LD) pumped Q switched high efficient intracavity frequency doubled Nd ∶YAG laser is reported here. The authors have designed an optical coupler and pointed out that the key to increasing harmonic conve...A laser diode (LD) pumped Q switched high efficient intracavity frequency doubled Nd ∶YAG laser is reported here. The authors have designed an optical coupler and pointed out that the key to increasing harmonic conversion efficiency is to decrease the loss of fundamental wave. In the experiments, a fundamental mode output laser was acquired. When the pumping power was 12 W, 2.6 W average output power at 1 064 nm with AO Q switch was obtained. 2.1 W average output power at 532 nm was obtained with intracavity frequency doubling, and the highest second harmonic conversion efficiency was 82 0 0.展开更多
Non-stoichiometric copper selenide(Cu_(2-x)Se,x=0.18~0.25)nanomaterials have attracted extensive attentions due to their excellent thermoelectric,optoelectronic and photocatalytic performances.However,efficient produc...Non-stoichiometric copper selenide(Cu_(2-x)Se,x=0.18~0.25)nanomaterials have attracted extensive attentions due to their excellent thermoelectric,optoelectronic and photocatalytic performances.However,efficient production of Cu_(2-x)Se nanoparticles(NPs)through a green and convenient way is still hindered by the inevitable non-environmentally friendly operations in common chemical synthesis.Herein,we initially reveal the coexistence of seleninic acid content and elemental selenium(Se)NPs in pulsed laser-generated Se colloidal solution.Consequently,we put forward firstly a closedcycle reaction mode for totally green production of Cu_(1.8)Se NPs to exclude traditional requirements of high temperature and toxic precursors by using Se colloidal solution.In such closed-cycle reaction,seleninic acid works as the initiator to oxidize copper sheet to release cuprous ions which can catalyze the disproportion of Se NPs to form Se O_(3)^(2-)and Se^(2-)ions and further produce Cu_(2-x)Se NPs,and the by-product SeO_(3)^(2-)ions promote subsequent formation of cuprous from the excessive Cu sheet.In experiments,the adequate copper(Cu)sheet was simply dipped into such Se colloidal solution at 70℃,and then the stream of Cu_(1.8)SeNPs could be produced until the exhaustion of selenium source.The conversion rate of Se element reaches to more than 75%when the size of Se NPs in weakly acidic colloidal solution is limited between 1 nm and 50 nm.The laser irradiation duration shows negative correlation with the size of Se NPs and unobvious impact to the p H of the solution which both are essential to the high yield of Cu_(1.8)SeNPs.Before Cu sheet is exhausted,Se colloidal solution can be successively added without influences to the product quality and the Se conversion rate.Such green methodology positively showcases a brand-new and potential strategy for mass production of Cu_(2-x)Se nanomaterials.展开更多
High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of r...High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of renewable Fraxinus mandshurica was conducted by waterjet-assisted CO_(2)laser(WACL)technology.A quadratic mathematical model for describing the relationship between surface roughness changes and cutting parameters was established.The effects of cutting speed,flow pressure and laser power on the kerf surface roughness of Fraxinus mandshurica when cutting transversally were discussed by response surface method.The experimental results showed that kerf surface roughness decreased under a lower laser power,higher cutting speed and higher flow pressure.When the cutting speed was 30 mm/s,flow pressure was 1.58 MPa and laser power was 45 W,the actual surface roughness of the optimized Fraxinus mandshurica was 2.41μm,and it was in accord with the theoretically predicted surface roughness value of 2.54μm,so the model fitted the actual situation well.Through the analysis of 3D profile morphology and micromorphology,it was concluded that the optimized kerf surface of Fraxinus mandshurica was smoother,the cell wall was not destroyed and the tracheid was clear.It provides the theoretical basis for wood micromachining.展开更多
基金This work was supported by the National Natural Science Foundation of China(Nos.U21A20493,62104204,and 62234011)the National Key Research and Development Program of China(No.2017YFE0131500)the President’s Foundation of Xiamen University(No.20720220108).
文摘Room temperature low threshold lasing of green GaNbased vertical cavity surface emitting laser(VCSEL)was demonstrated under continuous wave(CW)operation.By using self-formed InGaN quantum dots(QDs)as the active region,the VCSEL emitting at 524.0 nm has a threshold current density of 51.97 A cm^(-2),the lowest ever reported.The QD epitaxial wafer featured with a high IQE of 69.94%and theδ-function-like density of states plays an important role in achieving low threshold current.Besides,a short cavity of the device(~4.0λ)is vital to enhance the spontaneous emission coupling factor to 0.094,increase the gain coefficient factor,and decrease the optical loss.To improve heat dissipation,AlN layer was used as the current confinement layer and electroplated copper plate was used to replace metal bonding.The results provide important guidance to achieving high performance GaN-based VCSELs.
文摘The aerospace and military sectors have widely used AA7075, a type of 7075 aluminum alloy, due to its exceptional mechanical performance. Selective laser melting (SLM) is a highly effective method for producing intricate metallic components, particularly in the case of aluminum alloys like Al-Si-Mg. Nevertheless, the production of high-strength AA7075 by SLM is challenging because of its susceptibility to heat cracking and elemental vaporization. In this study, AA7075 powders were mechanically mixed with SiC and TiC particles. Subsequently, this new type of AA7075 powder was effectively utilized in green laser printing to create solid components with fine-grain strengthening microstructures consisting of equiaxial grains. These as-printed parts exhibit a tensile strength of up to 350 MPa and a ductility exceeding 2.1%. Hardness also increases with the increasing content of mixed powder, highlighting the essential role of SiC and TiC in SLM for improved hardness and tensile strength performance. .
基金supported by the National Key Research and Development Program of China(Grant Nos.2017YFB0405000,2016YFB0401803)the National Natural Science Foundation of China(Grant Nos.61834008,61574160,and 61704184)support of the Chinese Academy of Science Visiting Professorship for Senior International Scientists (Grant No.2013T2J0048)
文摘The inhomogeneous broadening parameter and the internal loss of green LDs are determined by experiments and theoretical fitting. It is found that the inhomogeneous broadening plays an important role on the threshold current density of green LDs. The green LD with large inhomogeneous broadening even cannot lase. Therefore, reducing inhomogeneous broadening is a key issue to improve the performance of green LDs.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 61107086, 61172010, and 61101058)the Science and Technology Committee of Tianjin, China (Grant No. 11JCYBJC01100)the National High Technology Research and Development Program of China (Grant No. 2011AA010205)
文摘We successfully obtain a high-average-power high-stability Q-switched green laser based on diode-side-pumped composite ceramic Nd：YAG in a straight piano-concave cavity. The temperature distribution in composite ceramic Nd：YAG crystal is numerically analyzed and compared with that of conventional Nd：YAG crystal. By using a composite ceramic Nd：YAG rod and a type-II high gray track resistance KTP （HGTR-KTP） crystal, a green laser with an average output power of 165 W is obtained at a repetition rate of 25 kHz, with a diode-to-green optical conversion of 14.68%, and a pulse width of 162 ns. To the best of our knowledge, both the output power and optical-to-optical efficiency are the highest values for green laser systems with intracavity frequency doubling of this novel composite ceramic Nd：YAG laser to date. The power fluctuation at around 160 W is lower than 0.3% in 2.5 hours.
基金Project supported by the National Natural Science Foundation of China （Grant Nos 60278024 and 60438020）.
文摘We first experimentally demonstrate a laser-diode end-pumped self-Q-switched and mode-locked Nd,Cr：YAG green laser with a KTP crystal as the intra-cavity frequency doubler. The device produces an average output power of 680 mW at 532 nm. The corresponding pulse width of the Q-switched envelope of the green laser is 170 ＋ 20 ns. The mode-locked pulses have a repetition rate of approximately 183 MHz and the average pulse duration is estimated to be around sub-nanosecond. It is found that the intra-cavity frequency doubling greatly improves the modulation depth and stability of the mode-locked pulses within the Q-switched envelope.
文摘The possible ways and progress of infrared or red laser pumped green and blue laser emissions from a single solid state material doped by rare earth ions are outlined. The green and blue lasers realized from infrared laser pumped rare earth doped nonlinear laser crystals by means of self frequency conversion and from infrared laser pumped rare earth doped bulk, fiber and microsphere materials by means of frequency upconversion are introduced in detail. Other kinds of devices and methods are also compared. The typical nonlinear laser crystals such as YAl 3(BO 3) 4, GdAl 3(BO 3) 4, YCa 4O(BO 3) 3 , GdCa 4O(BO 3) 3, and the typical upconversion fluoride fibers are compared and analyzed. The major problems remaining to be solved and the developing trends in the area are also discussed.
文摘A laser diode (LD) pumped Q switched high efficient intracavity frequency doubled Nd ∶YAG laser is reported here. The authors have designed an optical coupler and pointed out that the key to increasing harmonic conversion efficiency is to decrease the loss of fundamental wave. In the experiments, a fundamental mode output laser was acquired. When the pumping power was 12 W, 2.6 W average output power at 1 064 nm with AO Q switch was obtained. 2.1 W average output power at 532 nm was obtained with intracavity frequency doubling, and the highest second harmonic conversion efficiency was 82 0 0.
基金the Fund from Hefei National Laboratory for Physical Sciences at the Microscale(Grant No.KF2020110)the Natural Science Foundation of Anhui Province,China(Grant No.1908085ME146)+3 种基金the Key Research and Development Plan of Anhui Province,China(Grant No.201904a05020049)the Director Fund of Institute of Solid State Physics,Chinese Academy of Sciences(Grant No.2019DFY01)the National Natural Science Foundation of China(Grant Nos.52071313 and 51971211)the Hefei Institutes of Physical Science,Chinese Academy of Sciences Director’s Fund(Grant Nos.YZJJZX202018 and YZJJ202102)。
文摘Non-stoichiometric copper selenide(Cu_(2-x)Se,x=0.18~0.25)nanomaterials have attracted extensive attentions due to their excellent thermoelectric,optoelectronic and photocatalytic performances.However,efficient production of Cu_(2-x)Se nanoparticles(NPs)through a green and convenient way is still hindered by the inevitable non-environmentally friendly operations in common chemical synthesis.Herein,we initially reveal the coexistence of seleninic acid content and elemental selenium(Se)NPs in pulsed laser-generated Se colloidal solution.Consequently,we put forward firstly a closedcycle reaction mode for totally green production of Cu_(1.8)Se NPs to exclude traditional requirements of high temperature and toxic precursors by using Se colloidal solution.In such closed-cycle reaction,seleninic acid works as the initiator to oxidize copper sheet to release cuprous ions which can catalyze the disproportion of Se NPs to form Se O_(3)^(2-)and Se^(2-)ions and further produce Cu_(2-x)Se NPs,and the by-product SeO_(3)^(2-)ions promote subsequent formation of cuprous from the excessive Cu sheet.In experiments,the adequate copper(Cu)sheet was simply dipped into such Se colloidal solution at 70℃,and then the stream of Cu_(1.8)SeNPs could be produced until the exhaustion of selenium source.The conversion rate of Se element reaches to more than 75%when the size of Se NPs in weakly acidic colloidal solution is limited between 1 nm and 50 nm.The laser irradiation duration shows negative correlation with the size of Se NPs and unobvious impact to the p H of the solution which both are essential to the high yield of Cu_(1.8)SeNPs.Before Cu sheet is exhausted,Se colloidal solution can be successively added without influences to the product quality and the Se conversion rate.Such green methodology positively showcases a brand-new and potential strategy for mass production of Cu_(2-x)Se nanomaterials.
基金supported by the Joint Scientific and Technological Innovation Project of Hainan Province(2021CXLH0001)the Teaching Reform in Higher Education of Heilongjiang Province(SJGY20210135)+4 种基金the Key Subject of Education Planning in Heilongjiang Province(GJB1423352)the Guiding Innovation Fund Project of Northeast Petroleum University(2022YDL-06 and 2021YDL-13)Daqing City Guiding Science and Technology Project(zd-2021-41)the Scientific Research Start-Up Fund Project of Northeast Petroleum University(2021KQ09 and 2019KQ67)the National Key R&D Program of China(2017YFD0601004).
文摘High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of renewable Fraxinus mandshurica was conducted by waterjet-assisted CO_(2)laser(WACL)technology.A quadratic mathematical model for describing the relationship between surface roughness changes and cutting parameters was established.The effects of cutting speed,flow pressure and laser power on the kerf surface roughness of Fraxinus mandshurica when cutting transversally were discussed by response surface method.The experimental results showed that kerf surface roughness decreased under a lower laser power,higher cutting speed and higher flow pressure.When the cutting speed was 30 mm/s,flow pressure was 1.58 MPa and laser power was 45 W,the actual surface roughness of the optimized Fraxinus mandshurica was 2.41μm,and it was in accord with the theoretically predicted surface roughness value of 2.54μm,so the model fitted the actual situation well.Through the analysis of 3D profile morphology and micromorphology,it was concluded that the optimized kerf surface of Fraxinus mandshurica was smoother,the cell wall was not destroyed and the tracheid was clear.It provides the theoretical basis for wood micromachining.
