Evaporation Erosion During the Relay Contact Breaking Process Based on a Simplified Arc Model

Evaporation erosion of the contacts is one of the fundamental failure mechanisms for relays. In this paper, the evaporation erosion characteristics are investigated for the copper contact pair breaking a resistive direct current （dc） 30 V/10 A circuit in the air. Molten pool simulation of the contacts is coupled with the gas dynamics to calculate the evaporation rate. A simplified arc model is constructed to obtain the contact voltage and current variations with time for the prediction of the current density and the heat flux distributions flowing from the arc into the contacts. The evaporation rate and mass variations with time during the breaking process are presented. Experiments are carried out to verify the simulation results.

An evaporation duct prediction model coupled with the MM5

Evaporation duct is an abnormal refractive phenomenon in the marine atmosphere boundary layer. It has been generally accepted that the evaporation duct prominently affects the performance of the electronic equipment over the sea because of its wide distribution and frequent occurrence. It has become a research focus of the navies all over the world. At present, the diagnostic models of the evaporation duct are all based on the Monin-Obukhov similarity theory, with only differences in the flux and character scale calculations in the surface layer. These models are applicable to the stationary and uniform open sea areas without considering the alongshore effect. This paper introduces the nonlinear factor a and the gust wind item wg into the Babin model, and thus extends the evaporation duct diagnostic model to the offshore area under extremely low wind speed. In addition, an evaporation duct prediction model is designed and coupled with the fifth generation mesoscale model （MMS）. The tower observational data and radar data at the Pingtan island of Fujian Province on May 25-26, 2002 were used to validate the forecast results. The outputs of the prediction model agree with the observations from 0 to 48 h. The relative error of the predicted evaporation duct height is 19.3% and the prediction results are consistent with the radar detection.

A Micro-layer Model for the Lubrication Effect Near Collisions of Immersed Particles

A micro-layer model is proposed to account for the lubrication effect of liquid layer near collisions of immersed particles at moderate particle Reynolds number.This new model is to allow determination of the pressure profile within the micro-layer including the fluid inertia and viscosity.Then a correction based on the micro-layer model is applied to unsteady 3-D direct simulation of a particle approaching another one.The simulation is based on a modified immersed boundary method with direct force scheme.The quantitative agreement between numerical and experimental results validates the model presented in the study.The simulation results show that the fluid is squeezed prior to contact.When a particle approaches a flat wall or another particle,the lubrication force,obtained by integrating the pressure profile over the particle surface,is increased and prevents the particle from approaching.The model predicts that the velocity of approaching particle starts to decrease when separation distance of particles is less than 0.1dp,where dp is the particle diameter.

Comparison and analysis of bare soil evaporation models combined with ASTER data in Heihe River Basin

Based on ASTER （Advanced Spaceborne Thermal Emission and Reflection Radiometer） remote sensing data, bare soil evaporation was estimated with the Penman-Monteith model, the Priestley-Taylor model, and the aerodynamics model. Evaporation estimated by each of the three models was compared with actual evaporation, and error sources of the three models were analyzed. The mean absolute relative error was 9% for the Penman-Monteith model, 14% for the Priestley-Taylor model, and 32% for the aerodynamics model; the Penman-Monteith model was the best of these three models for estimating bare soil evaporation. The error source of the Penman-Monteith model is the neglect of the advection estimation. The error source of the Priestley-Taylor model is the simplification of the component of aerodynamics as 0.72 times the net radiation. The error source of the aerodynamics model is the difference of vapor pressure and neglect of the radiometric component. The spatial distribution of bare soil evaporation is evident, and its main factors are soil water content and elevation.

Numerical simulation of metal evaporation based on the kinetic model equation and the direct simulation Monte Carlo method

Metal evaporation on the basis of the kinetic model equations(BGK and S-model) and the direct simulation Monte Carlo(DSMC) method was investigated computationally under the circumstances of collimators existing or not. Numerical data of distributions of number density, bulk velocity and temperature were reported over a wide range of evaporation rate.It was shown that these results reached a good agreement for the case of small evaporation rate, while the deviations became increasingly obvious with the increase of evaporation rate, especially when the collimators existed. Moreover, the deposition thickness over substrate obtained from the kinetic model equations were inaccurate even though the evaporation rate was small. All of the comparisons showed the reliability of the kinetic model equations, which require less computational cost at small evaporation rate and simple structure.

THEORY DEPOSITION MODEL AND INFLUENCING FACTORS DURING PROCESS OF PREPARING MICRO-LAYER LAMINATE BY EBPVD

This paper briefly introduces the characteristics of electron beam physical vapor depo-sition (EBPVD) technique and the whole process of preparing micro--layer compositelaminate. And several major influencing factors are presented and discussed. It wasfound that residual gas pressure should be low enough to guarantee the unobstructedtransporfation of vapor steam and electron beam; the evaporation method and evapo-ration speed are up to the different vapor pressure deficit of compositions of raw mate-rials; and the substrate temperature could have great influence on the microstructureof the micro--layer laminates.

Amodified numerical model for moisture-salt transport in unsaturated sandy soil under evaporation

Soil salinization,caused by salt migration and accumulation underneath the soil surface,will corrode structures.To analyze the moisture-salt migration and salt precipitation in soil under evaporation conditions,a mathematical model consisting of a series of theoretical equations is briefly presented.The filling effect of precipitated salts on tortuosity factor and evaporation rate are taken into account in relevant equations.Besides,a transition equation to link the solute transport equation before and after salt precipitation is proposed.Meanwhile,a new relative humidity equation deduced from Pitzer ions model is used to modify the vapor transport flux equation.The results show that the calculated values are in good agreement with the published experimental data,especially for the simulation of volume water content and evaporation rate of Toyoura sand,which confirm the reliability and applicability of the proposed model.

CFD-Based Numerical Simulation of Water Film Flash Evaporation with a New Flash Evaporation Model

In this study, a new mass model involving superheat, initial temperature, liquid height, evaporator diameter, and flashing time is established to describe the flash evaporation process of water film. Of 469 sets of flash experimental data from three previous researches, 305 sets were applied to optimize parameters, and the other 164 sets were used to verify the practicability of the model. The results showed that the mean relative error between the literature data and the model values was less than 16.3%, and the model statistics proved that the model was well-posed. Then, the kinetic model was obtained using the time derivative of the new mass model. Computational fluid dynamics simulation of water film flash evaporation was studied based on a user-defined function program of the new evaporation kinetic model. The new kinetic model shows more consistency with the experimental phenomena in terms of evaporated mass and temperature compared with the evaporation–condensation model in Fluent software and Gopalakrishna's model. This new kinetic model can be extended to describe the flash process of water solution under other conditions.

Improvements of evaporation drag model

A special visible experiment facility has been designed and built, and an observable experiment is per- formed by pouring one or several high-temperature particles into a water pool in the facility. The experiment result has verified Yang’s evaporation drag model, which holds that the non-symmetric profile of the local evaporation rate and the local density of vapor would bring about a resultant force on the hot particle so as to resist its motion. How- ever, in Yang’s evaporation drag model, radiation heat transfer is taken as the only way to transfer heat from hot par- ticle to the vapor-liquid interface, and all of the radiation energy is deposited on the vapor-liquid interface and con- tributed to the vaporization rate and mass balance of the vapor film. In improved model heat conduction and heat convection are taken into account. This paper presents calculations of the improved model, putting emphasis on the effect of hot particle’s temperature on the radiation absorption behavior of water.

Model for Periodic Analysis of the Quantity of Water Evaporated during Thermo-processing of Clay Designated for Production of Oven Refractory

A model has been derived for periodic analysis of the quantity of water evaporated during thermo-processing of clay designated for production of oven refractory. The model;γ = exp〔〔lnt/2.9206〕1.3〕 shows that the quantity of evaporated water during the drying process is dependent on the drying time, with the evaporating surface being constant. It was found that the validity of the model is rooted on the expression lnγ = (lnt/Logβ)N where both sides of the equation are correspondingly almost equal. The maximum deviation of the model-predicted quantity of evaporated water from the corresponding experimental value is less than 19% which is quite within the acceptable deviation range of experimental results. Water evaporation rate as obtained from experiment and derived model were evaluated to be 0.0536 and 0.0337g mins -1 respectively.

Evaluating the soil evaporation loss rate in a gravel-sand mulching environment based on stable isotopes data

In order to cope with drought and water shortages,the working people in the arid areas of Northwest China have developed a drought-resistant planting method,namely,gravel-sand mulching,after long-term agricultural practices.To understand the effects of gravel-sand mulching on soil water evaporation,we selected Baifeng peach(Amygdalus persica L.)orchards in Northwest China as the experimental field in 2021.Based on continuously collected soil water stable isotopes data,we evaluated the soil evaporation loss rate in a gravel-sand mulching environment using the line-conditioned excess(lc-excess)coupled Rayleigh fractionation model and Craig-Gordon model.The results show that the average soil water content in the plots with gravel-sand mulching is 1.86%higher than that without gravel-sand mulching.The monthly variation of the soil water content is smaller in the plots with gravel-sand mulching than that without gravel-sand mulching.Moreover,the average lc-excess value in the plots without gravel-sand mulching is smaller.In addition,the soil evaporation loss rate in the plots with gravel-sand mulching is lower than that in the plots without gravel-sand mulching.The lc-excess value was negative for both the plots with and without gravel-sand mulching,and it has good correlation with relative humidity,average temperature,input water content,and soil water content.The effect of gravel-sand mulching on soil evaporation is most prominent in August.Compared with the evaporation data of similar environments in the literature,the lc-excess coupled Rayleigh fractionation model is better.Stable isotopes evidence shows that gravel-sand mulching can effectively reduce soil water evaporation,which provides a theoretical basis for agricultural water management and optimization of water-saving methods in arid areas.

A Mathematical Model of an Evaporative Cooling Pad Using Sintered Nigerian Clay

Overtime, reduction in the amount of heat generated in engineering systems in operations have been of great concern and have continuously been under study. It is in line with the above that this research work developed a mathematical model of an evaporative cooling pad using sintered Nigerian clay. A physical model of the evaporative cooling phenomenon was developed followed by the derivation of the governing equations describing the energy and mass transfer for the clay model from the laws of conservation of continuum mechanics. A set of reasonable and appropriate as-sumptions were imposed upon the physical model. Constitutive relationships were also developed for further analysis of the developed equations. The finite element model of numerical methods was used to analyse the energy transfer governing equations which resulted in the determination of the temperature of the exposed boundary surface at any given time, t2 after the commencement of the evaporative cooling processes. In this paper, it was found out that surface temperature differences could be as much as 6?C in the first cycle of evaporative cooling with the potential of further reduction. Further, an equation for the prediction of the effectiveness of an evaporative cooling system using clay modeled cooling pads was developed. The findings in this research work can be applied in the design, construction and maintenance of evaporative coolers used to dissipate waste heat when a large amount of natural water is not readily available or if for environmental and safety reasons the large water body can no longer absorb waste heat.

Coupling effect between film boiling heat transfer and evaporation drag around a hot-particle in cold liquid

Extremely rapid evaporation could occur when high-temperature particles contact withlow-temperature liquid. This kind of phenomenon is associated with the engineering safety and the problems inhigh-transient multi-phase fluid and heat transfer. The aim of our study was to design and build an observable ex-periment facility. The first series of experiments were performed by pouring one or six high-temperature particles intoa low saturated temperature liquid pool. The particle's falling-down speed was recorded by a high-speed camera, thuswe can find the special resistant feature of the moving high-temperature particles, which is induced by the high-speedevaporation surrounding the particles. The study has experimentally verified the theory of evaporation drag model.

An Axial Dispersion Model for Evaporating Bubble Column Reactor

Evaporating bubble column reactor (EBCR) is a kind of aerated reactor in which the reaction heat is removed by the evaporation of volatile reaction mixture. In this paper, a mathematical model that accounts for the gas-liquid exothermic reaction and axial dispersions of both gas and liquid phase is employed to study the performance of EBCR for the process of p-xylene(PX) oxidation. The computational results show that there are remarkable concentration and temperature gradients in EBCR for high ratio of height to diameter (H/DT). The temperature is lower at the bottom of column and higher at the top, due to rapid evaporation induced by the feed gas near the bottom. The concentration profiles in the gas phase are more nonuniform than those (except PX) in the liquid phase, which causes more solvent burning consumption at high H/DT ratio. For p-xylene oxidation, theo ptimal H/DT is around 5.

Formation of Li Salts from Natural Brines during Isothermal Evaporation at 25℃

Li brines are the primary resources for Li salt industries.Evaporation is necessary to concentrate Li due to its low level of concentration in raw brines.The salt sequences during the evaporation of Li brines,especially the behavior of Li salts,represent key data for solar technologies.However,chemists cannot use any phase diagram to estimate Li salt sequences during evaporation at 25℃.The thermodynamic model proposed by us in 2003 represents the only tool for the prediction of equilibrium conditions during the evaporation of solutions containing Li^+,Na^+,K^+,Mg^2+/Cl^-,SO4^2-,and-H2O components at 25℃.In this paper,the predicted salt sequences of 20 brines are reported.The results indicate that (1) the first crystallized Li salt during evaporation of Li brine varies in brine composition;(2) lithium sulfate is crystallized in many cases initially for brines of magnesium sulfate subtype,while Db4 (Li2SO4 ·K2SO4 ) or Db3 (2Li2SO4 ·Na2SO4 ·K2SO4 ) appears first for sodium sulfate and magnesium sulfate subtypes with lower Mg/Li composition,and the final eutectic point is H+LiC+Lc+Ls+Car;(3) the final eutectic point is H+LiC+Lc+Car for brines of chloride type;and (4) Li content corresponding to the first crystallized Li salt is in the range of 0.43%-1%.These findings enhance our knowledge of Li chemistry and provide insights into solar pond technology of the Li-brine process.

Stilling and its Aerodynamic Effects on Pan Evaporation

Declines in wind speed(u)(termed as“stilling”)has been reported in many regions of the world.To explore the temporal trends of u and its aerodynamic effects is vital to understand the changes in water resources.This study analyzed the changes of temporal trends for u and its aerodynamic effects using the data during 1959-2000 at 266 stations across China.The improved PenPan model was used to estimate pan evaporation(Epan)and quantify the contribution of radiative and aerodynamic components(aerodynamic component separated into wind speed u,vapour pressure deficit D,and air temperature Ta).Climate factors include Epan measured with the standard Chinese 20 cm diameter pan,u,Ta,relative humidity(rh)and sunshine hours(sh).The results showed:stilling occurred in most of stations(206 among 266)and 105 stations presented significant decreasing trends at 99%confidence level;stilling was the main cause for controlling the trends in Epan in most part of China,especially in the west and north of China.The results indicated that decreasing trends in Epan due to stilling would inevitably alter water resources,and should be put further investigation incorporation other factors.

Evaporation and Combustion of a Drop of Liquid Fuel—A Review

The accelerated depletion of oil reserves and the often exorbitant cost of fossil fuels contribute to the development of fuels from renewable sources. The objective of this work is to analyze the influence of the properties of renewable fuels on their evaporation in natural convection, their combustion and their use in internal combustion engines. A summary of the various numerical and experimental works from the literature has been presented in this work. This work focuses on the numerical modelling of the natural convection evaporation of an isolated drop of a liquid fuel in natural convection. The transfers in the liquid and vapour phases are described by the conservation equations of mass and species, momentum and energy. The main feature of this work is the consideration of advection, azimuthal angle and thickness of the vapour phase of the drop during evaporation of the drop.

Modeling and numerical analysis of evaporative condensing regenerator

A two-dimensional steady state model was developed and solved numerically to predict the performance of evaporative condensing regenerator.Two-dimensional parameter distributions of air,solution and refrigerant were calculated by the mathematical model.The solution content first increases and then decreases along the solution flow direction.At y/Hr=0.98(where Hr is the height of regenerator),air humidity increases from 1.99% to 2.348% firstly and then decreases.The experimental results were used to validate mathematical model.It is indicated that the simulation results agree with experimental data well.The results not only show that the mathematical model can be used to predict the performance of regenerator,but also has great value in the design and improvement of evaporative condensing regenerator.

Numerical simulation on boiling heat transfer of evaporation cooling in a billet reheating furnace

The boiling heat transfer of evaporation cooling in a billet reheating furnace was simulated.The results indicate that the bubbles easily aggregate inside of the elbow and upper side of the horizontal regions in theπshaped support tubes.The circulation velocity increasing helps to improve the uniformity of vapor distribution and decrease the difference of vapor volume fraction between upper and down at end of the horizontal sections.With the increase of circulation velocity,the resistance loss and the circulation ratio both increase,but the former will decrease with the increase of work pressure.

Thermal Study and Modeling of the Cold Room of a Solar Adsoption Refrigerator

In this work, we are interested in the study of the thermal exchanges which take place at the evaporator of an adsorption refrigerator. Due to the cost of designing experimental devices and the impossibility of studying the influence of certain parameters experimentally, an alternative would be simulation. The aim is to provide a model for predicting the thermal behavior of the various elements in the cold room of an adsorption solar refrigerator. A dynamic modelling of the refrigerator taking into account fluid flow, heat and mass transfer phenomena in the cold room was made. The calculation code obtained using COMSOL 5.1 software makes it possible to analyze and study the influence of the various parameters on the performance of the system. In a second step, the theoretical results obtained were compared with the experimental results in order to validate the model. The analysis of the influence of the physical-thermal properties of the insulating material on the temperature of the chamber makes it possible to conclude that a material having a low density ρ, a low thermal conductivity λ and a low specific heat capacity offers better performance to the cold room. Better thermal insulation also implies having a reasonable insulation thickness.