Improvement of antifouling characteristics in a bioreactor of polypropylene microporous membrane by the adsorption of Tween 20

Surface modification by physical adsorption of Tween 20 was accomplished on polypropylene microporous membranes （PPMMs）. Attenuated total reflection-Fourier transform infrared spectroscopy （ATR/FT-IR） and field emission scanning electron microscope （FE- SEM） were used to characterize the chemical and morphological changes on the membrane surfaces. Water contact angles and relative pure water fluxes were measured. The data showed that the hydrophilic performance for the modified membranes increased with the increase in the adsorption amount of Tween 20 onto the surface or into the pores of polypropylene microporous membranes. To test the antifouling property of the membranes by the adsorption of Tween 20 in a membrane bioreactor （MBR）, filtration for active sludge was performed using synthetic wastewater. With the help of the data of water fluxes and the FE-SEM photos of the modified PPMMs before or after operating in a MBR for about 12 d, the PPMMs with monolayer adsorption of Tween 20 showed higher remained flux and stronger antifouling ability than unmodified membrane and other modification membranes studied.

Surface Modification of Polypropylene Microporous Membrane by Atmospheric-pressure Plasma Induced N-vinyl-2-pyrrolidone Graft Polymerization

Membrane surfaces modified with poly（N-vinyl-2-pyrrolidone） （PNVP） can be endowed with hydrophilicity, biocompatibility and functionality. In this work, atmospheric pressure dielectric barrier discharge plasma graft polymerization of N-vinyl-2-pyrrolidone （NVP） onto polypropylene （PP） microporous membrane surface was studied. The experimental results reveal that plasma treatment conditions, such as discharge power, treatment time and adsorbed NVP amount, have remarkable effects on the grafting degree of NVP. Structural and morphological changes on the membrane surfaces were characterized by attenuated total reflection-Fourier transform infrared spectroscopy （FT-IR/ATR）, X-ray photoelectron spectroscope （XPS） and field emission scanning electron microscopy （FE-SEM）. Water contact angles of the membrane surfaces were also measured by the sessile drop method. Water contact angles on the membrane surfaces decrease with the increase of NVP grafting degree, which indicates an enhanced hydrophilicity for the modified membranes. The effects of grafting degrees on pure water fluxes were also measured. It is shown that pure water fluxes increase with grafting degree firstly and then decrease adversely. Finally, filtration of bovine serum albumin （BSA） solution and platelets adhesion of the PNVP modified membranes show good protein resistance and potential biocompatibility due to the enhancement of surface hydrophilicity.

SURFACE MODIFICATION OF POLYPROPYLENE MICROPOROUS MEMBRANES BY THE ADSORPTION OF NON-IONIC SURFACTANTS

Surface modification by physical adsorption of a series of non-ionic surfactants including Tween 20, Tween 40, Tween 60, Tween 80 and Tween 85, was accomplished on polypropylene microporous hollow fiber and flat membranes. The adsorption curve of the membrane surface was analyzed by weight measurements and the typical results showed a twoplatform character similarly. Differences in the degree and curve shape of adsorption resulting from such factors as concentration, temperature, as well as water cleaning time were observed for Tween 85 among other Tweens. Attenuated total reflection - Fourier transform infrared spectroscopy analysis and field emission scanning electron microscopy observation showed that the adsorption of Tween on polypropylene microporous membrane （PPMM） is effective and occurs mainly in the pores of PPMMs at low adsorption amount, and on the membrane surface also at high adsorption value.

FORMATION AND MICROSTRUCTURE OF POLYETHYLENE MICROPOROUS MEMBRANES THROUGH THERMALLY INDUCED PHASE SEPARATION

Microporous membranes of low-high density polyethylene and their blends were prepared bythermally-induced phase separation of polymer/long-aliphatic chain alcohol (diluent) mixtures.The microstructures of this particular membrane, which depends on the diluent properties,polymer concentration and cooling rate, were observed by scanning electron microscopy.'Beehive-type,'leafy-like, and lacy porous structure morphologies can be formed,depending onthe blend composition and phase separation conditions, which were discussed by the polymer anddiluent crystallization processes.

SURFACE MODIFICATION OF POLYPROPYLENE MICROPOROUS MEMBRANE BY TETHERING POLYPEPTIDES

Two kinds of polypeptides were tethered onto the surface of polypropylene microporous membrane （PPMM） through a ring opening polymerization of L-glutamate N-carboxyanhydride initiated by amino groups which were introduced by ammonia plasma and y-aminopropyl triethanoxysilane treatments. X-ray photoelectron spectroscopy （XPS）, attenuated total reflectance Fourier transform infrared spectroscopy （FT-IR/ATR）, scanning electron microscopy （SEM）, together with water contact angle measurements were used to characterize the modified membranes. XPS analyses and FT-IR/ATR spectra demonstrated that polypeptides are actually grafted onto the membrane surface. The wettability of the membrane surface increases at first and then decreases with the increase in grafting degrees of polypeptide. Platelet adhesion and murine macrophage attachment experiments reveal an enhanced hemocompatibility for the polypeptide modified PPMMs. All these results give evidence that polypeptide grafting can simultaneously improve the hemocompatibility as well as reserve the hydrophobicity for the membrane, which will provide a potential approach to improve the performance of polypropylene hollow fiber microporous membrane used in artificial oxygenator.

Surface Modification of Polypropylene Microporous Membrane by Atmospheric-Pressure Plasma Immobilization of N,N-dimethylamino Ethyl Methacrylate

Surface modification of polypropylene microporous membrane （PPMM） was performed by atmospheric pressure dielectric barrier discharge plasma immobilization of N,Ndimethylamino ethyl methacrylate （DMAEMA）. Structural and morphological changes on the membrane surface were characterized by attenuated total reflection-Fourier transform infrared spectroscopy （FT-IR/ATR）, X-ray photoelectron spectroscope （XPS） and field emission scanning electron microscopy （FE-SEM）. Water contact angles of the membrane surfaces were also measured by the sessile drop method. Results reveal that both the plasma-treating conditions and the adsorbed DMAEMA amount have remarkable effects on the immobilization degree of DMAEMA. Peroxide determination by 1,1-diphenyl-2-picrvlhydrazyl （DPPH） method verifies the exsistence of radicals induced by plasma, which activize the immobilization reaction. Pure water contact angle on the membrane surface decreased with the increase of DMAEMA immobilization degree, which indicates an enhanced hydrophilicity for the modified membranes. The effects of immobilization degrees on pure water fluxes were also measured. It is shown that pure water fluxes first increased with immobilization degree and then decreased. Finally, permeation of bovine serum albumin （BSA） and lysozyme solution were measured to evaluate the antifouling property of the DMAEMA-modified membranes, from which it is shown that both hydrophilicity and electrostatic repulsion are beneficial for membrane antifouling.

PREPARATION AND CHARACTERIZATION OF PVDF-HFP MICROPOROUS MEMBRANE BY TEMPLATE METHOD

Porous poly（vinylidene fluoride-co-hexafluoropropylene） （PVDF-HFP） membranes were successfully prepared using dibutyl phthalate （DBP）, polyvinylpyrrolidone （PVP-K30）, polyethylene glycol 200 （PEG200） as templates. SEM was used to examine the morphology of the PVDF-HFP porous membranes. It was found that these membranes have an asymmetric structure and the blends of PVDF-HFP/DBP formed nanoporous membranes, whereas the blends of PVDF- HFP/PVP-K30 formed ＂sponge-like＂ and microporous membranes. Moreover, the average pore size and porosity was about 0.3 μm and 48.7%, respectively. The crystallinity, thermal stability and mechanical strength of membranes were characterized by XRD, DSC, TGA and stress-strain tests. The results showed that the membranes are a crystals with excellent thermal stability. It was an effective way to regulate pore size and morphology of the PVDF-HFP membranes.

PREPARATION OF EVOH MICROPOROUS MEMBRANES via THERMALLY INDUCED PHASE SEPARATION USING BINARY SOLVENTS

Microporous ethylene-vinyl alcohol copolymer （EVOH） flat membranes and hollow-fiber membranes with 38 mol% ethylene content were prepared via thermally induced phase separation （TIPS） using the mixture of 1,4-butanediol and poly（ethylene glycol）（PEG400） as diluents. Effects of the ratio of 1,4-butanediol to PEG400 on the phase diagrams, phase separation mechanism and membrane morphology were studied by small angle light scattering （SALS） measurements, differential scanning calorimetry （DSC）, and scanning ele~：tron microscopy （SEM）. It was found that by varying the composition of the binary solvent, the phase diagrams and membrane morphology can be controlled successfully. Moreover, the phase diagrams showed that broader regions of Liquid-Liquid （L-L） phase separation were obtained, as well as closer distances between L-L phase separation lines and Solid-Liquid （S-L） phase separation lines, Interconnected structures observed both in the flat membrane and hollow fiber membrane consist with the above results.

Effect of Fumed SiO_2 on Pore Formation Mechanism and Various Performances of β-iPP Microporous Membrane Used for Lithium-ion Battery Separator

In this work, four samples containing different contents of fumed SiO_2 were prepared to improve the pore size distribution and various properties of b nucleated isotatic polypropylene（b-i PP） biaxial membrane used for lithium-ion battery separator. The wide-angle X-ray diffraction（WAXD） and differential scanning calorimetry（DSC） results show that the fumed SiO_2 promotes the formation of b-crystal slightly and narrows down the thickness distribution of b-lamellae; meanwhile, evenly distributed SiO_2 within b-i PP can be inspected by scanning electron microscopy（SEM）. Moreover, further detailed characterization of morphological evolutions during biaxial stretching by tensile testing and SEM manifests that SiO_2 can strengthen b-i PP and make the samples deform more homogeneously, resulting in a gradually elaborate and finer oriented microfibril structure after longitudinal stretching, in which more uniform defects distribute between fibrils and restrain the formation of coarse fibrils effectively. Therefore, more superior microporous structure emerges with the addition of SiO_2, accompanied by narrower pore size distribution and better connectivity between microvoids, which is confirmed by mercury porosimeter and diminished Gurley value. Moreover, the lower thermal shrinkage, decreased shrinkage rate and suppressed porosity reduction indicate that fumed SiO_2 improves thermal and dimensional stability of membrane dramatically. Furthermore, due to the excellent wettability of SiO_2 with electrolyte, the microporous membranes doped with SiO_2 have higher electrolyte uptake, even after heat treatment at elevated temperature.

MICROPOROUS PVDF-HFP-BASED POLYMER MEMBRANES FORMED FROM SUPERCRITICAL CO_2 INDUCED PHASE SEPARATION

Microporous poly(vinylidene fluoride-co-hexafluoropropylene)(PVDF-HFP)membranes following supercritical CO_2 induced phase separation process were prepared using four solvents.The solid electrolytes of PVDF-HFP were formed by microporous PVDF-HFP membranes filled and swollen by a liquid electrolyte.The effect of the solvents on the morphology and structure,electrolyte absorptions and lithium ionic conductivity of the activated membranes were investigated.It was approved that all the membrane had the similar...

Inorganic microporous membranes for hydrogen separation:Challenges and solutions

Porous membrane separation is a competitive hydrogen purification technology due to the advantages of environmental friendliness,energy-saving,simple operation,and low cost.Benefiting from the booming development of materials science and chemical science,great progress has been made in H_(2) separation with porous membranes.This review focuses on the latest advances in the design and fabrication of H_(2) separation inorganic microporous membranes,with emphasis on the synthetic strategies to achieve structural integrity,continuity and stability.This review starts with a brief introduction to the membrane separation mechanisms,followed by an elaboration on the synthetic challenges and corresponding solutions of various high-performance inorganic microporous membranes based on zeolites,silica,carbon,and metal-organic frameworks(MOFs).At last,by highlighting the prospects of ultrathin two-dimensional(2D)porous membranes,we wish to shed some light on the further development of new materials and membranes for highly efficient hydrogen separation.

Fabrication of Microporous Membranes from Melt Extruded Polypropylene Precursor Films via Stretching: Effect of Annealing

In this work, the effects of annealing conditions on the microstructure of polypropylene（PP） precursor films and further on the porous structure and permeability of stretched membranes were investigated. Combinations of WAXD, FTIR, DSC and DMA results clearly showed the crystalline orientation and crystallinity of the precursor film increased with annealing temperature, while the molecular chain entanglements in the amorphous phase decreased. Changes in the deformation behavior suggested more lamellar separation occurred for the films annealed at higher temperatures. Surface morphologies of the membranes examined by SEM revealed more pore number and uniform porous structure as the annealing temperature increased. In accordance with the SEM results, the permeability of the membranes increased with annealing temperature. On the other hand, it was found that 10 min was almost enough for the annealing process to obtain the microporous membranes with an optimal permeability.

Preparation and characterization of antibacterial microporous membranes fabricated by poly(AMS-co-DMAEMA)grafted polypropylene via melt-stretching method

Polypropylene microporous membranes are typical hydrophobic separation membranes, but the high hydrophobicity and lack of functionality easily cause bacterial adhesion, thus inducing membrane pollution. Poly（AMS-co-DMAEMA） （PAD） was designed and synthesized by copolymerization of a-methyl styrene （AMS） and functional monomer 2-（dimethylamino）ethyl methacrylate （DMAEMA）, and then grafted onto PP chains by melt blending. Microporous membranes of blended PP containing different contents of PAD are made by casting and stretching, and the polycation microporous membrane is then obtained via quaternization. The permeability and porosity of the microporous membrane achieve the best when the grafting efficiency reaches 42.16%, and the hydrophilicity of the microporous membrane is improved. The results show that the modified membranes fabricated in this method have good antibacterial properties.

Enhancement of the flux for polypropylene hollow fiber membrane in a submerged membrane-bioreactor by surface modification

To improve its limiting flux and antifouling characteristics in a submerged membrane-bioreactor （SMBR） for wastewater treatment, polypropylene hollow fiber microporous membrane （PPHFMM） was surface-modified by the plasma-induced immobilization of poly （N-vinyl-2-pyrrolidone） （PVP） and the plasma treatment with different gases respectively. Attenuated total reflection-Fourier transform infrared spectroscopy （FT-IR/ATR）, X-ray photoelectron spectroscopy （XPS） and field emission scanning electron microscope （FE-SEM） were used to characterize the structural and morphological changes on the membrane surface. Water contact angle was measured by the sessile drop method. It was found that the water contact angle was 128.8, 72.3, 62.7, 74.4, 79.1, 86.3, and 71.3° for the nascent, PVP-immobilized, air, 02, Ar, CO2 and H2O plasma treated PPHFMM, respectively. The SMBR was operated at fixed transmembrane pressure to determine the limiting flux for the PPHFMM before and after surface modification. Results showed that the limiting flux appeared to be 103, 159, 117, 133, 136, 121 and 152 L/（m^2· h） for the nascent, PVP-immobilized, air, O2, At, CO2 and H2O plasma treated PPHFMM, respectively. After continuous operation for about 50 h in the SMBR, the antifouling characteristics were improved to some extent.

INTERACTION BETWEEN THE SURFACE GLYCOSYLATED POLYPROPYLENE MEMBRANE AND LECTIN

A glycopolymer bearing glucose residues was tethered onto the surface of polypropylene microporous membrane by UV-induced graft polymerization ofα-allyl glucoside.Concanavalin A (Con A),a glucose recognizing lectin,could be specifically adsorbed to the membrane surface.On the other hand,the membrane surface showed no recognition ability to another lectin peanut agglutinin.Moreover,the recognition complex between the glycosylated membrane surface and Con A could be inhibited by glucose and mannose solution.T...

Plasma Modified Polypropylene Membranes as the Lithium-Ion Battery Separators

To reduce the thermal shrinkage of the polymeric separators and improve the safety of the Li-ion batteries,plasma treatment and plasma enhanced vapor chemical deposition（PECVD）of SiO_x-like are carried out on polypropylene（PP）separators,respectively.Critical parameters for separator properties,such as the thermal shrinkage rate,porosity,wettability,and mechanical strength,are evaluated on the plasma treated PP membranes.O_2 plasma treatment is found to remarkably improve the wettability,porosity and electrolyte uptake.PECVD SiO_x-like coatings are found to be able to effectively reduce the thermal shrinkage rate of the membranes and increase the ionic conductivity.The electrolyte-philicity of the Si Ox-like coating surface can be tuned by the varying O_2 content in the gas mixture during the deposition.Though still acceptable,the mechanical strength is reduced after PECVD,which is due to the plasma etching.

Preparation of microparticles and nanoparticles using membrane-assisted dispersion,micromixing,and evaporation processes

Synthetic microporous membranes are increasingly used for energy-efficient and controlled production of micro-and nanoparticles and micro-and nanoemulsions with tuneable morphology and physico-chemical properties through various micromixing,emulsification,and evaporation processes.In emul-sification processes,the membrane pores are used for dispersed phase injection and size-controlled generation of droplets and droplet-templated particles.In micromixing processes,membrane is utilised as a micromixer for mixing two miscible liquids,usually solvent and antisolvent-rich solutions,which leads to the creation of supersaturation and subsequent nanoprecipitation or crystallisation.In mem-brane evaporation processes,membrane is used to prevent phase dispersion while allowing efficient molecular diffusion of solvent and/or antisolvent vapour through gas-filled pores.Membrane dispersion processes can be operated continuously by decoupling shear stress on the membrane surface from cross flow using tube insets,flow pulsations,swirling flow,membrane oscillations or membrane rotations.Droplet generation and solidification can be performed continuously in a single pass by connecting membrane module with a downstream reactor.Membrane dispersion processes can be used for pro-duction of nanoparticles such as nanovesicles(liposomes,micelles,ethosomes,and niosomes),nanogels,polymeric,lipid and metallic nanoparticles,and nanocrystals.The main advantages of membrane-assisted particle generation are in low energy consumption,controlled geometry and hydrodynamic conditions at the microscale level,flexible throughput due to modular and scalable design of membrane devices,and a wide choice of available microporous membranes with various wall porosities,wetta-bilities,pore sizes,and pore morphologies to suit different applications.

Mussel-inspired Modification of Microporous Polypropylene Membranes for Functional Catalytic Degradation

In this manuscript, an easy method of anchoring Au nanoparticles onto a polypropylene （PP） membrane to prepare a composite Au-PP membrane with catalytic activity was demonstrated. The surface of the PP membrane was first modified with a primary amine by mussel-inspired dopamine polymerization. Then, the modified PP membrane was used to reduce chloroauric acid to anchor Au nanoparticles onto the surface, forming a Au-PP membrane. The surface morphology and composition of the modified PP membrane were characterized with SEM, ATR-FTIR and XPS. The catalytic activity of the Au-PP membrane was also evaluated by the degradation of a model dye solution of methylene blue. The fabricated membrane shows excellent catalytic performance, and the catalytic activity can be effectively regenerated.

Separators for Lithium Ion Batteries

1 Results A separator for rechargeable batteries is a microporous membrane placed between electrodes of opposite polarity, keeping them apart to prevent electrical short circuits and at the same time allowing rapid transport of lithium ions that are needed to complete the circuit during the passage of current in an electrochemical cell, and thus plays a key role in determining the performance of the lithium ion battery. Here provides a comprehensive overview of various types of separators for lithium io...