In order to meet the urgent needs in wireless communications, microwave image synthetic aperture radars （SAR）, and electronic warfare systems, this dissertation studies several types of broadband dual-polarized plan...In order to meet the urgent needs in wireless communications, microwave image synthetic aperture radars （SAR）, and electronic warfare systems, this dissertation studies several types of broadband dual-polarized planar antenna elements and arrays, and proposes a few of novel designs with experimental verification. The main accomplishments reported in the dissertation are as follows.展开更多
The probe-fed patch antennas were proposed by changing the parameters such as dielectric materials and dimensions of patch for detail investigation of changes in output characteristics. Four rectangular slots were int...The probe-fed patch antennas were proposed by changing the parameters such as dielectric materials and dimensions of patch for detail investigation of changes in output characteristics. Four rectangular slots were introduced separately for optimizing the antenna design and characteristics. This study illustrated the changes of output characteristics of an antenna with respect to the number of introduced slots on the radiating patch in addition to the effect of various dielectric materials on antenna performances. The antenna performances were analyzed by plotting the observation of various dielectric materials. The changes of antenna characteristics were also observed by introducing four numbers of slots on each edge of the patch to improve radiation characteristics with a wider impedance bandwidth.展开更多
The dual band equilateral triangular microstrip antennas are realized by cutting the slots of either quarter wave or half wave in length, inside the patch. In this design, however these simpler approximations of slot ...The dual band equilateral triangular microstrip antennas are realized by cutting the slots of either quarter wave or half wave in length, inside the patch. In this design, however these simpler approximations of slot length against the frequency do not give closer results for different slot lengths and there positions inside the patch. In this paper, the modal variations of slot cut patch antennas over wide frequency range are studied. It is observed that the slot does not introduce any mode but reduces the higher order mode resonance frequency of the patch and along with the fundamental mode realizes dual band response. The formulations of the resonant length for the mode introduce by the slots in these antennas are proposed. The resonance frequencies calculated using proposed formulations agree well with the simulated results with an error of less than 5%.展开更多
Microstrip patch antenna (MPA) is widely implemented in different communication systems. One of the main disadvantages of MPA which limits its applications is its narrow bandwidth. In this paper I enhanced the bandwid...Microstrip patch antenna (MPA) is widely implemented in different communication systems. One of the main disadvantages of MPA which limits its applications is its narrow bandwidth. In this paper I enhanced the bandwidth of MPA by inserting multiple slots in its ground plane. I used FR-4 substrate to design this antenna. The dimensions of this antenna are 59 mm and 79 mm. The dielectric constant is 4.4 and the height is 1.6 mm. I inserted up to 15 slots in ground plane with 1mm width. The spacing between slots is 3 mm. I investigated two designs. In the first design, slots were arranged in parallel to the feeding line. In the second one, slots were arranged horizontally to the feeding line. The main objective of this paper is to design and simulate MPA suitable for wide number of applications. Antenna bandwidth improvement is 18%. All the simulations were obtained by using HFSS simulator.展开更多
Circularly polarized microstrip antenna is frequently realized by cutting the slot inside the patch and feeding it along the diagonal axis. In the reported literature, procedure to design them at any given frequency i...Circularly polarized microstrip antenna is frequently realized by cutting the slot inside the patch and feeding it along the diagonal axis. In the reported literature, procedure to design them at any given frequency is not available. In proposed work, circularly polarized slot cut circular microstrip antenna at 900 MHz is discussed. By studying the surface current distributions at two orthogonal modes, formulations in their resonant length are proposed. The frequencies calculated using them closely agree with simulated results. Using proposed formulation, procedure to design circular polarized antennas at different frequencies is presented that gives circular polarized response. Thus, proposed work will be helpful to design similar circular polarized circular microstrip antenna at any desired frequency.展开更多
Ultra wide bands antennas with notched bands characteristics have recently been considered for efficient communication between devices. In this paper, a compact ultra-wideband antenna (UWB) for UWB applications with t...Ultra wide bands antennas with notched bands characteristics have recently been considered for efficient communication between devices. In this paper, a compact ultra-wideband antenna (UWB) for UWB applications with triple bandnotched characteristics is presented. The proposed antenna consists of a square patch with four truncated corners and a partial ground plane with a rectangular slit. The operation bandwidth of the designed antenna is from 2.66 GHz to more than 13.5 GHz. Band-notched characteristics of antenna to reject the frequency band of 3.18 - 3.59 GHz and 4.70 - 5.88 GHz, is realized by inserting two C-shaped slots in the patch, the third band of 9.54 - 12.22 GHz is achieved by slottype capacitively-loaded loop (CLL) inserted in the patch near the feed line. Details of the proposed antenna design and simulated results are presented and discussed.展开更多
A broadband feeding technique for the uniplanar tapered slot antenna (TSA) is presented. The TSA operates at a center frequency of 6.5 GHz with a 7 GHz bandwidth (107 percent). The antenna and feed are realized with a...A broadband feeding technique for the uniplanar tapered slot antenna (TSA) is presented. The TSA operates at a center frequency of 6.5 GHz with a 7 GHz bandwidth (107 percent). The antenna and feed are realized with a broadband microstrip-to-slotline transition on a low permittivity high frequency substrate, Rogers RT/Duroid 5880. The input impedance of the system is designed for 50 Ω compatibility with other system components, and the cross polarization is kept below –30 dB. The developed TSA system was simulated with commercially available electromagnetic software and manufactured. Measured results validate the design process and the antenna’s performance.展开更多
The design of a seven-band stacked patch antenna for the C, X and Ku band is presented. The antenna consists of an H-slot loaded fed patch, stacked with dual U-slot loaded rectangular patch to generate the seven frequ...The design of a seven-band stacked patch antenna for the C, X and Ku band is presented. The antenna consists of an H-slot loaded fed patch, stacked with dual U-slot loaded rectangular patch to generate the seven frequency bands. The total size of the antenna is 39.25 × 29.25 mm2. The multiband stacked patch antenna is studied and designed using IE3D simulator. For verification of simulation results, the antenna is analyzed by circuit theory concept. The simulated return loss, radiation pattern and gain are presented. Simulated results show that the antenna can be designed to cover the frequency bands from (4.24 GHz to 4.50 GHz, 5.02 GHz to 5.25 GHz) in C-band application, (7.84 GHz to 8.23 GHz) in X-band and (12.16 GHz to 12.35 GHz, 14.25 GHz to 14.76 GHz, 15.25 GHz to 15.51 GHz, 17.52 GHz to 17.86 GHz) in Ku band applications. The bandwidths of each band of the proposed antenna are 5.9%, 4.5%, 4.83%, 2.36%, 3.53%, 1.68% and 1.91%. Similarly the gains of the proposed band are 2.80 dBi, 4.39 dBi, 4.54 dBi, 10.26 dBi, 8.36 dBi and 9.91 dBi, respectively.展开更多
This study introduces a new design of planar antenna array for ISM band applications at 2.4 GHz. This prototype is switched beam antenna, namely planar antenna with four meandered slotted triangular elements (PAFMSTE)...This study introduces a new design of planar antenna array for ISM band applications at 2.4 GHz. This prototype is switched beam antenna, namely planar antenna with four meandered slotted triangular elements (PAFMSTE), which is proposed for wireless indoor applications. The Base Station (BS) equipped with this planar antenna is preferred to be at the center position on the room ceiling to cover all sectors of the room. It is designed to use four directional triangular elements arranged to form a square planar antenna array. The PAFMSTE is used to obtain optimal directivity in four directions in azimuth plane with 3 dB beamwidth of 90°at a specific orientation of 30°in elevation plane. Switched parasitic technique is used to enable PAFMSTE to steer a directional beam through four locations by using four PIN diodes switches. The High Frequency Structure Simulator (HFSS) is used as an efficient simulation tool to optimize the performance of the PAFMSTE antenna. The fabrication and measurements of the PAFMSTE antenna are introduced. The proposed antenna enable radio positioning via Angle of Arrival (AOA) information collected from nearby devices. Then, the Cramér-Rao Bound (CRB) is presented for AOA estimation using identically and equally spaced antenna elements. The CRB depends on the directivity, where the maximum values of CRB are 1.35 × 10<sup>-3</sup> and 8 × 10<sup>-3</sup> at HPBW of 60° and 90°, respectively.展开更多
文摘In order to meet the urgent needs in wireless communications, microwave image synthetic aperture radars （SAR）, and electronic warfare systems, this dissertation studies several types of broadband dual-polarized planar antenna elements and arrays, and proposes a few of novel designs with experimental verification. The main accomplishments reported in the dissertation are as follows.
基金supported by the University Grants Commission Project under Grant No.F.PSW-195/14-15(ERO)
文摘The probe-fed patch antennas were proposed by changing the parameters such as dielectric materials and dimensions of patch for detail investigation of changes in output characteristics. Four rectangular slots were introduced separately for optimizing the antenna design and characteristics. This study illustrated the changes of output characteristics of an antenna with respect to the number of introduced slots on the radiating patch in addition to the effect of various dielectric materials on antenna performances. The antenna performances were analyzed by plotting the observation of various dielectric materials. The changes of antenna characteristics were also observed by introducing four numbers of slots on each edge of the patch to improve radiation characteristics with a wider impedance bandwidth.
文摘The dual band equilateral triangular microstrip antennas are realized by cutting the slots of either quarter wave or half wave in length, inside the patch. In this design, however these simpler approximations of slot length against the frequency do not give closer results for different slot lengths and there positions inside the patch. In this paper, the modal variations of slot cut patch antennas over wide frequency range are studied. It is observed that the slot does not introduce any mode but reduces the higher order mode resonance frequency of the patch and along with the fundamental mode realizes dual band response. The formulations of the resonant length for the mode introduce by the slots in these antennas are proposed. The resonance frequencies calculated using proposed formulations agree well with the simulated results with an error of less than 5%.
文摘Microstrip patch antenna (MPA) is widely implemented in different communication systems. One of the main disadvantages of MPA which limits its applications is its narrow bandwidth. In this paper I enhanced the bandwidth of MPA by inserting multiple slots in its ground plane. I used FR-4 substrate to design this antenna. The dimensions of this antenna are 59 mm and 79 mm. The dielectric constant is 4.4 and the height is 1.6 mm. I inserted up to 15 slots in ground plane with 1mm width. The spacing between slots is 3 mm. I investigated two designs. In the first design, slots were arranged in parallel to the feeding line. In the second one, slots were arranged horizontally to the feeding line. The main objective of this paper is to design and simulate MPA suitable for wide number of applications. Antenna bandwidth improvement is 18%. All the simulations were obtained by using HFSS simulator.
文摘Circularly polarized microstrip antenna is frequently realized by cutting the slot inside the patch and feeding it along the diagonal axis. In the reported literature, procedure to design them at any given frequency is not available. In proposed work, circularly polarized slot cut circular microstrip antenna at 900 MHz is discussed. By studying the surface current distributions at two orthogonal modes, formulations in their resonant length are proposed. The frequencies calculated using them closely agree with simulated results. Using proposed formulation, procedure to design circular polarized antennas at different frequencies is presented that gives circular polarized response. Thus, proposed work will be helpful to design similar circular polarized circular microstrip antenna at any desired frequency.
文摘Ultra wide bands antennas with notched bands characteristics have recently been considered for efficient communication between devices. In this paper, a compact ultra-wideband antenna (UWB) for UWB applications with triple bandnotched characteristics is presented. The proposed antenna consists of a square patch with four truncated corners and a partial ground plane with a rectangular slit. The operation bandwidth of the designed antenna is from 2.66 GHz to more than 13.5 GHz. Band-notched characteristics of antenna to reject the frequency band of 3.18 - 3.59 GHz and 4.70 - 5.88 GHz, is realized by inserting two C-shaped slots in the patch, the third band of 9.54 - 12.22 GHz is achieved by slottype capacitively-loaded loop (CLL) inserted in the patch near the feed line. Details of the proposed antenna design and simulated results are presented and discussed.
文摘A broadband feeding technique for the uniplanar tapered slot antenna (TSA) is presented. The TSA operates at a center frequency of 6.5 GHz with a 7 GHz bandwidth (107 percent). The antenna and feed are realized with a broadband microstrip-to-slotline transition on a low permittivity high frequency substrate, Rogers RT/Duroid 5880. The input impedance of the system is designed for 50 Ω compatibility with other system components, and the cross polarization is kept below –30 dB. The developed TSA system was simulated with commercially available electromagnetic software and manufactured. Measured results validate the design process and the antenna’s performance.
文摘The design of a seven-band stacked patch antenna for the C, X and Ku band is presented. The antenna consists of an H-slot loaded fed patch, stacked with dual U-slot loaded rectangular patch to generate the seven frequency bands. The total size of the antenna is 39.25 × 29.25 mm2. The multiband stacked patch antenna is studied and designed using IE3D simulator. For verification of simulation results, the antenna is analyzed by circuit theory concept. The simulated return loss, radiation pattern and gain are presented. Simulated results show that the antenna can be designed to cover the frequency bands from (4.24 GHz to 4.50 GHz, 5.02 GHz to 5.25 GHz) in C-band application, (7.84 GHz to 8.23 GHz) in X-band and (12.16 GHz to 12.35 GHz, 14.25 GHz to 14.76 GHz, 15.25 GHz to 15.51 GHz, 17.52 GHz to 17.86 GHz) in Ku band applications. The bandwidths of each band of the proposed antenna are 5.9%, 4.5%, 4.83%, 2.36%, 3.53%, 1.68% and 1.91%. Similarly the gains of the proposed band are 2.80 dBi, 4.39 dBi, 4.54 dBi, 10.26 dBi, 8.36 dBi and 9.91 dBi, respectively.
文摘This study introduces a new design of planar antenna array for ISM band applications at 2.4 GHz. This prototype is switched beam antenna, namely planar antenna with four meandered slotted triangular elements (PAFMSTE), which is proposed for wireless indoor applications. The Base Station (BS) equipped with this planar antenna is preferred to be at the center position on the room ceiling to cover all sectors of the room. It is designed to use four directional triangular elements arranged to form a square planar antenna array. The PAFMSTE is used to obtain optimal directivity in four directions in azimuth plane with 3 dB beamwidth of 90°at a specific orientation of 30°in elevation plane. Switched parasitic technique is used to enable PAFMSTE to steer a directional beam through four locations by using four PIN diodes switches. The High Frequency Structure Simulator (HFSS) is used as an efficient simulation tool to optimize the performance of the PAFMSTE antenna. The fabrication and measurements of the PAFMSTE antenna are introduced. The proposed antenna enable radio positioning via Angle of Arrival (AOA) information collected from nearby devices. Then, the Cramér-Rao Bound (CRB) is presented for AOA estimation using identically and equally spaced antenna elements. The CRB depends on the directivity, where the maximum values of CRB are 1.35 × 10<sup>-3</sup> and 8 × 10<sup>-3</sup> at HPBW of 60° and 90°, respectively.
