Effect of Process Parameters of Microwave Assisted Extraction (MAE) on Polysaccharides Yield from Pumpkin

Process parameters of microwave assisted extraction （MAE） of the polysaccharides from pumpkin viz. extraction temperature, time and liquid-solid ratio were studied by using single factor and response surface methodology method. The results showed that the liquid-solid ratio was the most important factor in polysaccharides yield, followed the extraction temperature was the least important factor. The optimum microwave assisted extraction co by ndi extraction time, and tions for the highest polysaccharides yield from pumpkin （16.76%-4-0.38%） were obtained by using the response surface methodology with extraction time of 29 min, an extraction temperature of 79 ℃ and a liquid-solid ratio of 22 mL·g^-1. Validation experiment result well agreed with predicted value.

Catalytic performance and synthesis of a Pt/graphene-TiO_2 catalyst using an environmentally friendly microwave-assisted solvothermal method

A Pt/graphene‐TiO2catalyst was prepared by a microwave‐assisted solvothermal method and was characterized by X‐ray diffraction,scanning electron microscopy,transmission electron microscopy,cyclic voltammetry,and linear sweep voltammetry.The cubic TiO2particles were approximately60nm in size and were distributed on the graphene sheets.The Pt nanoparticles were uniformly distributed between the TiO2particles and the graphene sheet.The catalyst exhibited a significant improvement in activity and stability towards the oxygen reduction reaction compared with Pt/C,which resulted from the high electronic conductivity of graphene and strong metal‐support interactions.

Mathematical Modeling and Optimization of the Microwave Assisted Extraction of the Solid Waste of the Pomegranate Juice Industry

Pomegranate pomace is the solid waste of the pomegranate juice industry which accounts for approximately 50%of the quantity of the fruits,which is processed into juice and is a good raw material for production of high added value products with diverse uses.Pomegranate pomace is rich in polyphenols and flavonoids which could substitute the potentially hazardous synthetic antioxidants/antimicrobials used in agro-food and cosmetics sectors.In this work,eco-friendly aqueous microwave assisted extraction of pomegranate pomace was investigated and optimized in order to produce effectively novel natural antioxidant/antimicrobial extracts.A three-factorial response surface optimization methodology with centered Box&Behnken experimental design was used to obtain the predictive models and the maximum values of total polyphenols,total flavonoids and total antioxidant capacity(TAC).The three optimization factors involved were:(a)water/solid ratio;(b)extraction temperature;(c)extraction time and the effectiveness and robustness of the three models were statistically verified by ANOVA.

Mathematical Modeling and Optimization of the Microwave Assisted Extraction of the Natural Polyphenols and Flavonoids from the Raw Solid Waste of the Orange Juice Industry

Orange pomace is the solid waste of the orange juice industry which accounts for approximately 50%of the quantity of the fruits processed into juice and is a good raw material for production of high added value products with diverse uses.Orange pomace is rich in polyphenols and flavonoids which can substitute the potentially hazardous or less desirable chemical antioxidants/antimicrobials used in agro-food and cosmetics industry.In this work,an eco-friendly aqueous microwave assisted extraction of orange pomace was investigated and optimized in order to produce aqueous bioactive antioxidant/antimicrobial extracts.A three factorial Response Surface Optimization methodology with centered Box&Behnken experimental design was used to obtain optimum values of total polyphenols and total flavonoids and build predictive models for their optimal extraction conditions.The three optimization factors in terms of applied process parameters were(a)water/solid ratio,(b)extraction temperature and(c)extraction time.The effectiveness and statistical soundness of the two corresponding models regarding optimal total polyphenols and flavonoids were verified by Analysis of Variance(ANOVA).

不同提取方法对苗药黑骨藤果实挥发油的研究

To analyze the chemical constituents of volatile oils from the fruit of Periploca forrestii Schltr.which were collected in Guizhou province.This volatile oils were extracted by simultaneous distillation extraction (SDE)and microwave assistant extraction(MAE) method,and ananlyzed by gas chromatography-mass spectrometry(GC-MS)method.The main chemical compounds were methyl salicylate,β-amyrin and β-amyrin acetate etc.The compounds from the volatile oils extracted with SDE and MAE are quite different.The results provide scientific proof for the further development and utilization of Periploca forrestii Schltr.

Engineering graphitic carbon nitride with expanded interlayer distance for boosting photocatalytic hydrogen evolution

Regulating interlayer distance is a crucial factor in the development of two‐dimensional(2D)nanomaterials.A 2D metal‐free photocatalyst,such as graphitic carbon nitride(g‐C3N4),exhibits morphology‐and microstructure‐dependent photocatalytic activity.Herein,we report a straightforward and facile route for the preparation of unique lamellar g‐C3N4,by co‐firing melamine and ammonium chloride via microwave‐assisted heating.Through the decomposition of NH4Cl,the evaporation of NH3 gas can effectively overcome van der Waals forces,expanding the interlayer distance of g‐C3N4,thereby creating a lamellar structure consisting of nanosheets.Compared with bulk g‐C3N4,the NH3‐derived lamellar g‐C3N4 exhibits a larger specific surface area and enhanced optical absorption capability,which increase photocatalytic hydrogen production because of the highly active structure,excellent utilization efficiency of photon energy,and low recombination efficiency of photogenerated charge carriers.This study provides a simple strategy for the regulation of the g‐C3N4 microstructure toward highly efficient photocatalytic applications.

Preparation and characterization of nano-crystalline diamond films on glass substrate

Adherent nano diamond films were successfully deposited on glass substrate bymicrowave plasma assisted CVD method in H_2-CH_4 and Ar-CH_4 environment. Raman, AFM (Atomic ForceMicroscope), TEM (Transmission Electron Microscope), FTIR, and Nano Indentation techniques were usedfor characterization of the obtained nano diamond films. It was found that the average grain sizewas less than 100 nm with a surface roughness value as low as 2 nm. The nano diamond films werefound to have excellent transparency in visible and IR spectrum range, and were as hard as naturaldiamond. Experimental results were presented. Mechanisms for nano diamond film deposition werediscussed.

The Antioxidant Activity of Barley Malt Rootlet Extracts in Heated Corn Oil at Frying Temperature

In this study the antioxidant activity of barley malt rootlet (BMR) extracts was evaluated in heat treated corn oil up to 5 hours at 185°C frying temperature. The antioxidant activity of BMR extracts was measured at 25, 50, 100 and 150 ppm concentrations. The free and bound antioxidant phenolics were extracted from BMR using three different extraction methods. Conventional solvent extraction (CSE), microwave assisted extraction (MAE) and autoclave assisted pretreated solvent extraction (APSE). In the present experiment, the total phenolic content and antioxidant activity of the various extracts were measured. Thiobarbituric acid reactive substances (TBARS) assay was used to evaluate the ability of the BMR to protect lipid peroxidation in corn oil at 185°C frying temperature. The formation of TBARS at 5 hours of heat treated corn oil has shown similar antioxidant levels in 150 ppm butylated hydroxytoluene (BHT) or MAE free phenolic extract added to corn oil. TBARS value for BHT was 1.896 ± 0.013 μg/mL of corn oil and for MAE was 1.896 ± 0.034 μg/mL of corn oil. The highest level of antioxidant activity was found for the free phenolic extracts. The order of inhibition of oxidation was found to be for free phenolics as follows: BHT (100 ppm) > APSE (50 ppm) > MAE (100 ppm) > CSE (100 ppm).

Mild and Efficient Synthesis of 1-（6-Chloroquinoxalin-2-yl）-2- [4-（trifluoromethyl）-2,6-dinitrophenyl] Hydrazine Derivatives by Microwave Irradiation

Some 1-（6-chloroquinoxalin-2-yl）-2-[4-（trifluoromethyl）-2,6-dinitrophenyl] hydrazine derivatives have been synthesized via both conventional and microwave assisted organic synthesis（MAOS） methods. The MAOS method is more effective on synthesizing these compounds than the conventional method in regard to the higher chemical yields of products（76%-98%） and the shorter reaction time（1-15 min）.

Microwave assisted synthesis of novel Hantzsch 1,4-dihydropyridines,acridine-1,8-diones and polyhydroquinolines bearing the tetrazolo[1,5-α]quinoline moiety and their antimicrobial activity assess

Microwave assisted efficient Hantzsch reaction via four-component coupling reactions of tetrazolo[1,5-α]quinoline-4-carbal-dehyde, dimedone/cyclohexane-1,3-dione,ethyl/methyl acetoacetate and ammonium acetate was described as the preparation of tetrazolo[1,5-α]quinoline based 1,4-dihydropyridines,acridine-1,8-diones and polyhydroquinolines.The process presented here is simple,rapid,environmentally welcoming and high yielding.All the derivatives were subjected to an in vitro antimicrobial screening against a representative panel of bacteria and fungi and results worth further investigations.

Pb(Ⅱ) removal from water using Fe-coated bamboo charcoal with the assistance of microwaves

Bamboo charcoal（BC） was used as starting material to prepare iron-modified bamboo charcoal（Fe-MBC） by its impregnation in FeCl 3 and HNO 3 solutions simultaneously,followed by microwave heating.The material can be used as an adsorbent for Pb（Ⅱ） contaminants removal in water.The composites were prepared with Fe molar concentration of 0.5,1.0 and 2.0 mol/L and characterized by means of N 2 adsorption-desorption isotherms,X-ray diffraction spectroscopy（XRD）,scanning electron microscopy coupled with energy dispersive X-ray spectrometry（SEM-EDS）,Fourier transform infrared（FT-IR） and point of zero charge（pH pzc） measurements.Nitrogen adsorption analyses showed that the BET specific surface area and total pore volume increased with iron impregnation.The adsorbent with Fe molar concentration of 2 mol/L（2Fe-MBC） exhibited the highest surface area and produced the best pore structure.The Pb（Ⅱ） adsorption process of 2Fe-MBC and BC were evaluated in batch experiments and 2Fe-MBC showed an excellent adsorption capability for removal Pb（Ⅱ）.The adsorption of Pb（Ⅱ） strongly depended on solution pH,with maximum values at pH 5.0.The ionic strength had a significant effect on the adsorption at pH 〈 6.0.The adsorption isotherms followed the Langmuir isotherm model well,and the maximum adsorption capacity for Pb（Ⅱ） was 200.38 mg/g for 2Fe-MBC.The adsorption processes were well fitted by a pseudo second-order kinetic model.Thermodynamic parameters showed that the adsorption of Pb（Ⅱ） onto Fe-MBC was feasible,spontaneous,and exothermic under the studied conditions,and the ion exchange mechanism played an significant role.These results have important implications for the design of low-cost and effective adsorbents in the removal of Pb（Ⅱ） from wastewater.

Microwave-assisted hydrothermal synthesis of Pt/SnO2 gas sensor for CO detection

In this paper,the Pt/SnO2 nanostructures were prepared via a facile one-step microwave assisted hydrothermal route.The structure of the introduced Pt/SnO2 and its gas-sensing properties toward CO were investigated.The results from the TEM test reveal that Pt grows on the SnO2 nanostructure,which was not found for bulk in this situ method,constructing Pt/SnO2.The results indicated that the sensor using 3.0 wt%Pt/SnO2 to 100 ppm carbon monoxide performed a superior sensing properties compared to 1.5 wt%and 4.5 wt%Pt/SnO2 at 225℃.The response time of 3.0 wt%sensor is 16 s to 100 ppm CO at225℃.Such enhanced gas sensing performances could be attributed to the chemical and electrical factors.In view of chemical factors,the presence of Pt facilitates the surface reaction,which will improve the gas sensing properties.With respect to the electrical factors,the Pt/SnO2 plays roles in increasing the sensor’s response due to its characteristic configuration.In addition,the one-step in situ microwave assisted process provides a promising and versatile choice for the preparation of gas sensing materials.

Microwave assisted synthesis of poly（2-hydroxyethylmethacrylate） grafted agar （Ag-g-P（HEMA）） and its application as a flocculant for wastewater treatment

Poly（2-hydroxyethylmethacrylate） chains were grafted onto the backbone of agar using a microwave assisted method involving a combination of microwave irradiation and ceric ammonium nitrate to initiate the grafting reaction. The synthesized graft copolymers were characterized by intrinsic viscosity measurements, Fourier transform infrared spectroscopy, elemental analysis （C, H, N, O and S） and scanning electron microscopy. Ag-g-P （HEMA）-2 showed a much higher flocculation efficacy than agar. The optimized dosage of flocculation for Ag-g-P （HEMA）-2 in the wastewater was found to be 0.75 ppm. Compared to agar, Ag-g-P（HEMA）-2 was found to considerably reduce the pollutant load in the wastewater.

Microwave-promoted Beller Synthesis of N-Substituted 2,3,3a,4,7,7a-Hexahydroisoindole-1,3-diones

A rapid and facile synthesis of N-substituted 2,3,3a,4,7,7a-hexahydroisoindole-l,3-dione derivatives via microwave-promoted Beller three-component domino reaction of α,β,-unsaturated aldehydes, amides and N-substituted maleimides was described.

Microwave assisted,ligand free,copper catalyzed reaction of aryl halides with phenyl urea

The ligand free coupling reaction of phenyl urea with different functionalized aryl halides in the presence of air stable Cu_2O and t-BuOK as a base gives symmetrical and unsymmetrical diarylureas in relatively high yields.This method is milder than the palladium catalyzed arylation and avoids the use of toxic phosphine ligand.

Microwave Assisted Extraction,Antioxidant Potential and Chromatographic Studies of Some Rasayana Drugs

Objective： To study and compare the conventional extraction procedure with microwave assisted extraction （MAE） for some Ayurvedic Rasayana drugs and to evaluate their antioxidant potential and carry out the characterization of extracts by thin layer chromatography. Methods： Three Ayurvedic rasayana plants Allium sativum Linn., Bombax ceiba Linn. and Inula racemosa Hook. were evaluated for an improved MAE methodology by determining the effects of grinding degree, extraction solvent, effect of dielectric constant and duration of time on the extractive value. Antioxidant potential of all three drugs was evaluated with 2,2-diphenyl-l-picrylhydrazyl （DPPH） radical scavenging activity and reducing power was determined by using Gallic acid as standard. Further thin layer chromatographic （TLC） analysis was performed on pre-activated Silica Gel G plates and Rf value were compared with those reported for the important biomarkers. Results： The total extractive value for Allium sativum Linn. was 36.95% （w/w） and 49.95% （w/w） for ethanol extraction respectively. In case of Bombax ceiba Linn. the yield of aqueous extract by MAE was 50% （w/w） compared to 42% （w/w） in ethanol （50% v/v）. Percent yield of Inula racernosa Hook. in aqueous extract was found to be 27.55% （w/w） which was better than ethanol extract （50%） where the yield was 25.95% （w/w）. Upon antioxidant activity evaluation A. safivum extract showed an absorbance of 0.980 ± 0.92 at concentration of 500 μg with maximum reducing capacity. This was followed by B. ceiba Linn. 0.825 ± 0.98 and I. racemosa Hook. with 0.799 ± 2.01 at a concentration of 500 μ g. TLC based standardization of A. sativum Linn. extract shows single spot with Rf value of 0.38, B. ceiba Linn. extract shows Rf values were 0.23, 0.58, 0.77, 0.92 and I. racemosa Hook. extract spot had a Rf value of 0.72. Conclusions： A significant improvement in extractive values was observed as a factor of time and other advantages by using MAE technology. All three drugs have high antioxidant potential and a TLC profiling similar to reported ones. The presence of fructan type polysaccharide can be further utilized for bioactivity directed fracUonation and evaluation of immunomodulatory activity.

Antioxidant and antiarthritic potential of berberine: In vitro and in vivo studies

Objective: To extract and isolate berberine from Berberis aristata(Berberidaceae). Isolated berberine was characterised using spectroscopy and its antioxidant and antiarthritic activity was analyzed.Methods: The berberine was isolated from B. aristata using microwave-assisted extraction(MAE) and characterised by a spectroscopic technique. The isolated berberine was evaluated for its antioxidant activity in DPPH, nitric oxide, and superoxide scavenging assays, while antiarthritic activity was evaluated in the complete freund’s adjuvant(CFA)-induced arthritis rat model.Results: The antioxidant activity of berberine revealed potent antioxidant activity in DPPH, nitric oxide,and superoxide scavenging assays. The in vivo antiarthritic activity of berberine in the CFA-induced arthritis rat model showed a significant reduction in paw diameter, arthritic score, and an increase in body weight. Furthermore, a concentration-dependent ameliorating action of berberine on haematological parameters was noticed. Proinfammatory biomarkers, including IL-6, IL-10, and TGF-b in serum were reported, and histopathology examination revealed that berberine decreased pannus formation, synovial hyperplasia, and bone erosion. Radiographic investigation showed soft tissue infammation, bone resorption and erosion, joint gap reduction, and substantial connective tissue expansion after treatment with berberine.Conclusion: The ameliorating action on haematological parameters and proinfammatory biomarkers of berberine makes them a suitable remedy for the treatment of arthritis.

One-step preparation of carbon nanotubes with nickel as the core

CNTs with core-shell structure were successfully synthesized by a microwave-assisted polyol method,and magnetic Ni nanoparticles were employed as a catalyst. The preparation method is fast and simple. The structures,morphology and magnetic properties of the as-synthesized samples were investigated using Raman spectrometer,X-ray diffraction (XRD),transmission electron microscopy (TEM),vibrating sample magnetometer (VSM),respectively. The XRD results suggested that Ni particles used as a catalyst in our experiment were nano-sized. In this paper,magnetic Ni nanoparticles were employed as a catalyst,and an electric spark on metal Ni nanoparticles with the microwave eddy current effect could induce CNTs’ formation with the further reaction. The length of hollow carbon nanotubes was micro-sized and the diameters of most of the CNTs were varying from 18 to 20 nm according to the TEM images. Magnetic measurements demonstrated that CNTs with core-shell structure indicated a characteristic ferromagnetic behavior compared with Ni nanoparticles.

Technologies for extracting lipids from oleaginous microorganisms for biodiesel production

Recently, biodiesel has received much more attention. Soybean oil, rapeseed oil, palm oil and corn oil are primary feedstock for biodiesel production. However, biodiesel production from these traditional oil-rich crops is limited by land availability, climate, and environmental and social issues regarding the use of feed and food crops for fuel. Oleaginous microorganisms, including microalgae, bacteria, yeast and fungi can be cultivated with high lipid contents and used as promising feedstock for biodiesel production. However, the high cost of biodiesel production using oil microorganisms has been the biggest obstacle for its industrialization. The process of biodiesel production from microorganisms involves many steps, of which the lipids extraction is the most important and costly. Therefore, searching for an effective and economical extraction system is critical. Various approaches of lipids extraction are discussed in this review, including traditional extraction procedures such as solvent extraction, pressing and solvent integrated extraction, as well as some new procedures.

Magnetic modification of diamagnetic agglomerate forming powder materials

A simple method for the magnetic modification of various types of powdered agglomerate forming dia- magnetic materials was developed. Magnetic iron oxide particles were prepared from ferrous sulfate by microwave assisted synthesis. A suspension of the magnetic particles in water soluble organic solvent （methanol, ethanol, propanol, isopropyl alcohol, or acetone） was mixed with the material to be modified and then completely dried at elevated temperature. The magnetically modified materials were found to be stable in water suspension at least for 2 months.