Highly accurate symplectic element based on two variational principles

For the stability requirement of numerical resultants, the mathematical theory of classical mixed methods are relatively complex. However, generalized mixed methods are automatically stable, and their building process is simple and straightforward. In this paper, based on the seminal idea of the generalized mixed methods, a simple, stable, and highly accurate 8-node noncompatible symplectic element(NCSE8) was developed by the combination of the modified Hellinger-Reissner mixed variational principle and the minimum energy principle. To ensure the accuracy of in-plane stress results, a simultaneous equation approach was also suggested. Numerical experimentation shows that the accuracy of stress results of NCSE8 are nearly the same as that of displacement methods, and they are in good agreement with the exact solutions when the mesh is relatively fine. NCSE8 has advantages of the clearing concept, easy calculation by a finite element computer program, higher accuracy and wide applicability for various linear elasticity compressible and nearly incompressible material problems. It is possible that NCSE8 becomes even more advantageous for the fracture problems due to its better accuracy of stresses.

Mechanical performance of cold mix asphalt containing cup lump rubber as a sustainable bio-modifier

The road construction industry aims to contribute to the protection of already compromised environment.Cold mix asphalt(CMA)is a measure initiated by the road industry to protect the environment and preserve energy.Despite having additional benefits,CMA has attracted little attention due to its inferior performance.CMA's performance is enhanced using a sustainable binder bio-modifier,natural cup lump rubber(CLR)is one of them.This study evaluated the tensile properties,rutting,moisture susceptibility,and adhesion properties of CLR-modified CMA(CMA-CR).The tensile property was enhanced by 26%due to CLR modification.CMA-CR had excellent rutting resistance of less than 2 mm rut depth at 10,000 load cycles,showing 70%improvement compared with conventional CMA.Moisture susceptibility evaluation indicated that CMA-CR had tensile strength ratio(TSR)value of 104%,satisfying the minimum 80%requirement of AASHTO T283.It also retained more than 96%bitumen coating.The moisture damage resistance was improved by 12%and 10%in terms of TSR and stripping,respectively.The durability results revealed that the CMA-CR mixture prevented higher mass loss,representing 14%improvement compared with conventional CMA.

Mixed Matrix Membranes of Polysulfone/Polyimide Reinforced with Modified Zeolite Based Filler: Preparation, Properties and Application

In this work, polysulfone/polyimide（PSf/PI） mixed matrix membranes were fabricated by reinforcement of modified zeolite（MZ） particles through solution casting method for investigation of antibacterial activity against two gram negative bacteria（Salmonella typhi, Klebsella pneumonia） and two gram positive bacteria（Staphylococcus aureus, Bacillus subtilis）. The modified zeolite particles were incorporated to PSf and PI matrix and the influence of these particles on thermal, mechanical and structural properties was evaluated. The morphological evolution was investigated through scanning electron microscopy（SEM） and transmission electron microscopy（TEM） analysis, which revealed good compatibility between organic polymer matrix and inorganic filler. Mechanical stability was investigated by tensile testing while thermal analysis was evaluated by thermogravimetric analysis（TGA） and differential scanning calorimetry（DSC）. This revealed improvement in thermal properties with increasing filler concentration from 1 wt% to 10 wt%. Structural analysis was successfully done using X-ray diffraction analysis（XRD） and Fourier transform infrared（FTIR） spectroscopy. Solvent content of fabricated mixed matrix membranes was observed to decrease while moving from more hydrophilic to less hydrophilic solvent. However, addition of filler content enhanced the porosity of fabricated membranes. The synthesized mixed matrix membranes exhibited good antibacterial activity and the highest activity was shown by PSf/PI/MZ mixed matrix membrane. Therefore, the combination effect of PSf, PI and MZ sufficiently enhanced the antibacterial activity of mixed matrix membranes.

Mixed convection of alumina-water nanofluid inside a concentric annulus considering nanoparticle migration

A theoretical investigation was conducted of laminar fully developed mixed convection of alumina-water nanofluid through a vertical annulus, to improve its heating/cooling performance. We focused on con- trolling the nanoparticle migration and studying how it affected the heat transfer rate and pressure drop. Because the nanoparticles have very small dimensions, we only considered Brownian motion and ther- mophoretic diffusivity as the main causes of nanoparticle migration. Because thermophoresis is very sensitive to temperature gradients, we imposed various temperature gradients using asymmetric heat- ing. Considering hydrodynamically and thermally fully developed flow, the governing equations were reduced to two-point ordinary boundary value differential equations and were solved numerically. The imposed thermal asymmetry changed the direction of nanoparticle migration and distorted the velocity, temperature, and nanoparticle concentration profiles. Moreover, we found optimum values for the radius ratio （ζ） and heat flux ratio （ε）; with these optimum values, the nanofluid enhanced the efficacy of the system.

Testing and assessing the performance of a new warm mix asphalt with SMC

Warm mix asphalt （WMA} is a new technology which asphalt mix is produced and placed at normal temperature. It has advantages including low cost, environmentally friendly, haul-convenience, and so on. WMA has been widely tested and applied in the USA in the last decade, but it has just started in China. Recently, a new WMA using a new plastic- macromolecule-normal temperature additive, which was called ＂SMC＂ by the production company, was introduced as asphalt modifier. Based on discussing the strength forming process of this new WMA with SMC, a series of laboratory tests, including Marshall stability test （MST）, boiling test （BT）, modified immersion Marshall test （MIMT）, freeze-thaw split- ring test （FTST）, rutting test （RT）, low-temperature bending test （LTBT）, and abrasion loss test （ALT）, were conducted in this study to assess the performance of this WMA and the capability of applying it on low volume roads in China. SMC modified asphalt mixed under normal temperature is used in testing samples. It was found that this WMA product exhibited merits on its strength, which was about 6.7 kN bigger than the requirement of 5.0 kN in the JTG F40-2004, on high-temperature stability, which is about 1100 times/ram greater than the requirement of 600-1000 times/mm in the ）TG F40-2004, and on its storage stability. Based on these indicators, it is recommended that this product could be used for low volume low class roads construction. However, due to the relatively lower water resistance and low-temperature cracking resistance, this product is suggested to be applied first in the areas with warm weather and little rainfall. In order to improve the perfor- mance of this WMA with SMC, further research on this SMC asphalt modifier should be continued.