Anti-interference beam pattern design based on second-order cone programming optimization

When signal-to-interference ratio is low, the energy of strong interference leaked from the side lobe of beam pattern will infect the detection of weak target. Therefore, the beam pattern needs to be optimized. The existing Dolph-Chebyshev weighting method can get the lowest side lobe level under given main lobe width, but for the other non-uniform circular array and nonlinear array, the low side lobe pattern needs to be designed specially. The second order cone programming optimization （SOCP） algorithm proposed in the paper transforms the optimization of the beam pattern into a standard convex optimization problem. Thus there is a paradigm to follow for any array formation, which not only achieves the purpose of Dolph-Chebyshev weighting, but also solves the problem of the increased side lobe when the signal is at end fire direction The simulation proves that the SOCP algorithm can detect the weak target better than the conventional beam forming.

Improved design of reconfigurable frequency response masking filters based on second-order cone programming

In order to improve the design results for the reconfigurable frequency response masking FRM filters an improved design method based on second-order cone programming SOCP is proposed.Unlike traditional methods that separately design the proposed method takes all the desired designing modes into consideration when designing all the subfilters. First an initial solution is obtained by separately designing the subfilters and then the initial solution is updated by iteratively solving a SOCP problem. The proposed method is evaluated on a design example and simulation results demonstrate that jointly designing all the subfilters can obtain significantly lower minimax approximation errors compared to the conventional design method.

Two new predictor-corrector algorithms for second-order cone programming

Based on the ideas of infeasible interior-point methods and predictor-corrector algorithms, two interior-point predictor-corrector algorithms for the second-order cone programming （SOCP） are presented. The two algorithms use the Newton direction and the Euler direction as the predictor directions, respectively. The corrector directions belong to the category of the Alizadeh-Haeberly-Overton （AHO） directions. These algorithms are suitable to the cases of feasible and infeasible interior iterative points. A simpler neighborhood of the central path for the SOCP is proposed, which is the pivotal difference from other interior-point predictor-corrector algorithms. Under some assumptions, the algorithms possess the global, linear, and quadratic convergence. The complexity bound O（rln（εo/ε）） is obtained, where r denotes the number of the second-order cones in the SOCP problem. The numerical results show that the proposed algorithms are effective.

Robust Blind Separation for MIMO Systems against Channel Mismatch Using Second-Order Cone Programming

To improve the deteriorated capacity gain and source recovery performance due to channel mismatch problem,this paper reports a research about blind separation method against channel mismatch in multiple-input multiple-output(MIMO) systems.The channel mismatch problem can be described as a channel with bounded fluctuant errors due to channel distortion or channel estimation errors.The problem of blind signal separation/extraction with channel mismatch is formulated as a cost function of blind source separation(BSS) subject to the second-order cone constraint,which can be called as second-order cone programing optimization problem.Then the resulting cost function is solved by approximate negentropy maximization using quasi-Newton iterative methods for blind separation/extraction source signals.Theoretical analysis demonstrates that the proposed algorithm has low computational complexity and improved performance advantages.Simulation results verify that the capacity gain and bit error rate(BER) performance of the proposed blind separation method is superior to those of the existing methods in MIMO systems with channel mismatch problem.

A VU-decomposition method for a second-order cone programming problem

A vu-decomposition method for solving a second-order cone problem is presented in this paper. It is first transformed into a nonlinear programming problem. Then, the structure of the Clarke subdifferential corresponding to the penalty function and some results of itsvu-decomposition are given. Under a certain condition, a twice continuously differentiable trajectory is computed to produce a second-order expansion of the objective function. A conceptual algorithm for solving this problem with a superlinear convergence rate is given.

AN INFEASIBLE-INTERIOR-POINT PREDICTOR-CORRECTOR ALGORITHM FOR THE SECOND-ORDER CONE PROGRAM

A globally convergent infeasible-interior-point predictor-corrector algorithm is presented for the second-order cone programming （SOCP） by using the Alizadeh- Haeberly-Overton （AHO） search direction. This algorithm does not require the feasibility of the initial points and iteration points. Under suitable assumptions, it is shown that the algorithm can find an -approximate solution of an SOCP in at most O（√n ln（ε0/ε）） iterations. The iteration-complexity bound of our algorithm is almost the same as the best known bound of feasible interior point algorithms for the SOCP.

SMOOTHING NEWTON ALGORITHM FOR THE CIRCULAR CONE PROGRAMMING WITH A NONMONOTONE LINE SEARCH

In this paper, we present a nonmonotone smoothing Newton algorithm for solving the circular cone programming(CCP) problem in which a linear function is minimized or maximized over the intersection of an affine space with the circular cone. Based on the relationship between the circular cone and the second-order cone(SOC), we reformulate the CCP problem as the second-order cone problem(SOCP). By extending the nonmonotone line search for unconstrained optimization to the CCP, a nonmonotone smoothing Newton method is proposed for solving the CCP. Under suitable assumptions, the proposed algorithm is shown to be globally and locally quadratically convergent. Some preliminary numerical results indicate the effectiveness of the proposed algorithm for solving the CCP.

Day-ahead Optimization Schedule for Gas-electric Integrated Energy System Based on Second-order Cone Programming

This paper proposes an optimal day-ahead opti-mization schedule for gas-electric integrated energy system(IES)considering the bi-directional energy flow.The hourly topology of electric power system(EPS),natural gas system(NGS),energy hubs(EH)integrated power to gas(P2G)unit,are modeled to minimize the day-ahead operation cost of IES.Then,a second-order cone programming(SOCP)method is utilized to solve the optimization problem,which is actually a mixed integer nonconvex and nonlinear programming issue.Besides,cutting planes are added to ensure the exactness of the global optimal solution.Finally,simulation results demonstrate that the proposed optimization schedule can provide a safe,effective and economical day-ahead scheduling scheme for gas-electric IES.

Optimal design and verification of temporal and spatial filters using second-order cone programming approach

Temporal filters and spatial filters are widely used in many areas of signal processing. A number of optimal design criteria to these problems are available in the literature. Various computational techniques are also presented to optimize these criteria chosen. There are many drawbacks in these methods. In this paper, we introduce a unified framework for optimal design of temporal and spatial filters. Most of the optimal design problems of FIR filters and beamformers are included in the framework. It is shown that all the design problems can be reformulated as convex optimization form as the second-order cone programming （SOCP） and solved efficiently via the well-established interior point methods. The main advantage of our SOCP approach as compared with earlier approaches is that it can include most of the existing methods as its special cases, which leads to more flexible designs. Furthermore, the SOCP approach can optimize multiple required performance measures, which is the drawback of earlier approaches. The SOCP approach is also developed to optimally design temporal and spatial two-dimensional filter and spatial matrix filter. Numerical results demonstrate the effectiveness of the proposed approach.

Nonsingularity in second-order cone programming via the smoothing metric projector

Based on the differential properties of the smoothing metric projector onto the second-order cone,we prove that,for a locally optimal solution to a nonlinear second-order cone programming problem,the nonsingularity of the Clarke's generalized Jacobian of the smoothing Karush-Kuhn-Tucker system,constructed by the smoothing metric projector,is equivalent to the strong second-order sufficient condition and constraint nondegeneracy,which is in turn equivalent to the strong regularity of the Karush-Kuhn-Tucker point.Moreover,this nonsingularity property guarantees the quadratic convergence of the corresponding smoothing Newton method for solving a Karush-Kuhn-Tucker point.Interestingly,the analysis does not need the strict complementarity condition.

Exact Computable Representation of Some Second-Order Cone Constrained Quadratic Programming Problems

Solving the quadratically constrained quadratic programming(QCQP)problem is in general NP-hard.Only a few subclasses of the QCQP problem are known to be polynomial-time solvable.Recently,the QCQP problem with a nonconvex quadratic objective function over one ball and two parallel linear constraints is proven to have an exact computable representation,which reformulates the original problem as a linear semidefinite program with additional linear and second-order cone constraints.In this paper,we provide exact computable representations for some more subclasses of the QCQP problem,in particular,the subclass with one secondorder cone constraint and two special linear constraints.

Unified convergence analysis of a second-order method of multipliers for nonlinear conic programming

In this paper,we accomplish the unified convergence analysis of a second-order method of multipliers(i.e.,a second-order augmented Lagrangian method)for solving the conventional nonlinear conic optimization problems.Specifically,the algorithm that we investigate incorporates a specially designed nonsmooth(generalized)Newton step to furnish a second-order update rule for the multipliers.We first show in a unified fashion that under a few abstract assumptions,the proposed method is locally convergent and possesses a(nonasymptotic)superlinear convergence rate,even though the penalty parameter is fixed and/or the strict complementarity fails.Subsequently,we demonstrate that for the three typical scenarios,i.e.,the classic nonlinear programming,the nonlinear second-order cone programming and the nonlinear semidefinite programming,these abstract assumptions are nothing but exactly the implications of the iconic sufficient conditions that are assumed for establishing the Q-linear convergence rates of the method of multipliers without assuming the strict complementarity.

A stable implicit nodal integration-based particle finite element method(N-PFEM)for modelling saturated soil dynamics

In this study,we present a novel nodal integration-based particle finite element method(N-PFEM)designed for the dynamic analysis of saturated soils.Our approach incorporates the nodal integration technique into a generalised Hellinger-Reissner(HR)variational principle,creating an implicit PFEM formulation.To mitigate the volumetric locking issue in low-order elements,we employ a node-based strain smoothing technique.By discretising field variables at the centre of smoothing cells,we achieve nodal integration over cells,eliminating the need for sophisticated mapping operations after re-meshing in the PFEM.We express the discretised governing equations as a min-max optimisation problem,which is further reformulated as a standard second-order cone programming(SOCP)problem.Stresses,pore water pressure,and displacements are simultaneously determined using the advanced primal-dual interior point method.Consequently,our numerical model offers improved accuracy for stresses and pore water pressure compared to the displacement-based PFEM formulation.Numerical experiments demonstrate that the N-PFEM efficiently captures both transient and long-term hydro-mechanical behaviour of saturated soils with high accuracy,obviating the need for stabilisation or regularisation techniques commonly employed in other nodal integration-based PFEM approaches.This work holds significant implications for the development of robust and accurate numerical tools for studying saturated soil dynamics.

Quadratic Optimization over a Second-Order Cone with Linear Equality Constraints

This paper studies the nonhomogeneous quadratic programming problem over a second-order cone with linear equality constraints.When the feasible region is bounded,we show that an optimal solution of the problem can be found in polynomial time.When the feasible region is unbounded,a semidefinite programming(SDP)reformulation is constructed to find the optimal objective value of the original problem in polynomial time.In addition,we provide two sufficient conditions,under which,if the optimal objective value is finite,we show the optimal solution of SDP reformulation can be decomposed into the original space to generate an optimal solution of the original problem in polynomial time.Otherwise,a recession direction can be identified in polynomial time.Numerical examples are included to illustrate the effectiveness of the proposed approach.

基于混合整数二阶锥规划的主动配电网有功–无功协调多时段优化运行

通过日前多时段优化,可以为主动配电网中的分布式电源、无功补偿装置和储能装置安排合理高效的生产计划,以达到调节电压水平、提高能源资源利用率、节能降损的目的。首先建立基于三相Distflow潮流的辐射状配电网有功–无功协调动态优化模型。该模型考虑分布式电源出力、储能装置充放电功率、电容器阻投切等连续和离散决策变量,是一个典型的混合整数非凸非线性规划。该类模型缺乏严格高效的求解方法。为此,采用二阶锥松弛技术将其中的三相潮流方程进行凸化松弛,使得优化问题转化为可有效求解的混合整数二阶锥规划模型。最后,采用扩展的IEEE 33节点三相测试系统仿真计算,利用MOSEK等算法包求得电网中各设备动作时刻和投运容量,验证了所提方法寻优稳定、松弛精确、计算高效等特性。

计及排放权交易的机组组合问题研究

温室气体排放权交易将给电力系统优化运行带来新的挑战。基于总量管制和排放交易(cap and trade)模式,提出计及排放权交易的机组组合(emission trading unit commitment,ETUC)模型。该模型不仅考虑了排放配额约束,而且考虑了排放权的交易。基于二阶锥多面体近似法,提出一种求解ETUC问题的新方法。该方法将ETUC问题转化为混合整数二阶锥规划(mixed integersecond-order cone programming,MISOCP)模型,然后利用多面体近似法将二阶锥约束转化为线性约束,形成解决ETUC问题的混合整数线性规划(mixed integer linear programming,MILP)模型。在10—100机组24时段系统上进行仿真计算,验证所提模型和方法的正确性和有效性。

Multiple-constraint cooperative guidance based on two-stage sequential convex programming

An improved approach is presented in this paper to implement highly constrained cooperative guidance to attack a stationary target.The problem with time-varying Proportional Navigation(PN)gain is first formulated as a nonlinear optimal control problem,which is difficult to solve due to the existence of nonlinear kinematics and nonconvex constraints.After convexification treatments and discretization,the solution to the original problem can be approximately obtained by solving a sequence of Second-Order Cone Programming(SOCP)problems,which can be readily solved by state-of-the-art Interior-Point Methods(IPMs).To mitigate the sensibility of the algorithm on the user-provided initial profile,a Two-Stage Sequential Convex Programming(TSSCP)method is presented in detail.Furthermore,numerical simulations under different mission scenarios are conducted to show the superiority of the proposed method in solving the cooperative guidance problem.The research indicated that the TSSCP method is more tractable and reliable than the traditional methods and has great potential for real-time processing and on-board implementation.

Optimality conditions for sparse nonlinear programming

The sparse nonlinear programming （SNP） is to minimize a general continuously differentiable func- tion subject to sparsity, nonlinear equality and inequality constraints. We first define two restricted constraint qualifications and show how these constraint qualifications can be applied to obtain the decomposition properties of the Frechet, Mordukhovich and Clarke normal cones to the sparsity constrained feasible set. Based on the decomposition properties of the normal cones, we then present and analyze three classes of Karush-Kuhn- Tucker （KKT） conditions for the SNP. At last, we establish the second-order necessary optimality condition and sufficient optimality condition for the SNP.

Assessment on strength reduction schemes for geotechnical stability analysis involving the Drucker-Prager criterion

For geotechnical stability analysis involving the Drucker-Prager(DP)criterion,both the c-ϕreduction scheme and the M-K reduction scheme can be utilized.With the aid of the second-order cone programming optimized finite element method(FEM-SOCP),a comparison of the two strength reduction schemes for the stability analysis of a homogeneous slope and a multilayered slope is carried out.Numerical investigations disclose that the FoS results calculated by the c-ϕreduction scheme agree well with those calculated by the classical Morgenstern-Price solutions.However,the FoS results attained by the M-K reduction scheme may lead to conservative estimation of the geotechnical safety,particularly for the cases with large internal friction angles.In view of the possible big difference in stability analysis results caused by the M-K reduction scheme,the c-ϕreduction scheme is recommended for the geotechnical stability analyses involving the DP criterion.

Multiconstraint adaptive three-dimensional guidance law using convex optimization

The traditional guidance law only guarantees the accuracy of attacking a target. However, the look angle and acceleration constraints are indispensable in applications. A new adaptive three-dimensional proportional navigation(PN) guidance law is proposed based on convex optimization. Decomposition of the three-dimensional space is carried out to establish threedimensional kinematic engagements. The constraints and the performance index are disposed by using the convex optimization method. PN guidance gains can be obtained by solving the optimization problem. This solution is more rapid and programmatic than the traditional method and provides a foundation for future online guidance methods, which is of great value for engineering applications.