The Impact of Model Based Offset Scaling Technique on the Amplitude Variation with Offset Responses from 3D Seismic Data Acquired from the Tano Basin, Offshore Ghana

Amplitudes have been found to be a function of incident angle and offset. Hence data required to test for amplitude variation with angle or offset needs to have its amplitudes for all offsets preserved and not stacked. Amplitude Variation with Offset (AVO)/Amplitude Variation with Angle (AVA) is necessary to account for information in the offset/angle parameter (mode converted S-wave and P-wave velocities). Since amplitudes are a function of the converted S- and P-waves, it is important to investigate the dependence of amplitudes on the elastic (P- and S-waves) parameters from the seismic data. By modelling these effects for different reservoir fluids via fluid substitution, various AVO geobody classes present along the well and in the entire seismic cube can be observed. AVO analysis was performed on one test well (Well_1) and 3D pre-stack angle gathers from the Tano Basin. The analysis involves creating a synthetic model to infer the effect of offset scaling techniques on amplitude responses in the Tano basin as compared to the effect of unscaled seismic data. The spectral balance process was performed to match the amplitude spectra of all angle stacks to that of the mid (26°) stack on the test lines. The process had an effect primarily on the far (34° - 40°) stacks. The frequency content of these stacks slightly increased to match that of the near and mid stacks. In offset scaling process, the root mean square (RMS) amplitude comparison between the synthetic and seismic suggests that the amplitude of the far traces should be reduced relative to the nears by up to 16%. However, the exact scaler values depend on the time window considered. This suggests that the amplitude scaling with offset delivered from seismic processing is only approximately correct and needs to be checked with well synthetics and adjusted accordingly prior to use for AVO studies. The AVO attribute volumes generated were better at resolving anomalies on spectrally balanced and offset scaled data than data delivered from conventional processing. A typical class II AVO anomaly is seen along the test well from the cross-plot analysis and AVO attribute cube which indicates an oil filled reservoir.

Microbial Growth and Decay: A Commented Review of the Model

The paper reviews previous publications and reports some comments about a semi empirical model of the growth and decay process of a planktonic microbial culture. After summarizing and reshaping some fundamental mathematical expressions, the paper highlights the reasons for the choice of a suitable time origin that makes the parameters of the model self-consistent. Besides the potential applications to predictive microbiology studies and to effects of bactericidal drugs, the model allows a suitable proxy of the fitness of the microbial culture, which can be of interest for the studies on the evolution across some thousand generations of a Long Term Evolution Experiment.

Experimental investigation and theoretical modeling on scale behaviors of high salinity wastewater in zero liquid discharge process of coal chemical industry

Zero liquid discharge(ZLD)treatment and reuse equipment of high salinity wastewater in coal-chemical industry often occur in various types of blockage problems because of high salt content,affecting the long-term stability of the device.In this study,the effects of solution temperature,steel,reaction time and wall roughness on fouling were investigated.The changes in the contents of fouling and fouling substances were qualitatively and quantitatively analyzed by XRD and EDS respectively,and the formation of scale was observed by SEM.The results show that with temperature increasing,Q235 steel is the most difficult to scale.Scaling rate of all salt scales reaches a maximum after 12 h,and the fouling rate decreases significantly from 12 to 48 h.It gradually stabilizes at 48 to 96 h.With the roughness increasing,the thickness of fouling layer increases,and a linear relationship is presented for 1 to 10 h.By comparing actual and simulated wastewater scaling rates,the relationship between actual and simulated wastewater scaling rates is y=ax-0.494.The composition of the scale was analyzed,calcium carbonate is the main product and increases with fouling time.Based on the above-mentioned results combining literatures,the hybrid prediction model with calcium carbonate as the main product is put forward.It is discussed microscopically that calcium carbonate is converted from aragonite and vaterite in a thermodynamically metastable state to calcite in a thermodynamically stable state.

Physical modelling and scale effects of air-water flows on stepped spillways

During the last three decades, the introduction of new construction materials (e.g. RCC (Roller Compacted Concrete), strengthened gabions) has increased the interest for stepped channels and spillways. However stepped chute hydraulics is not simple, because of different flow regimes and importantly because of very-strong interactions between entrained air and turbu- lence. In this study, new air-water flow measurements were conducted in two large-size stepped chute facilities with two step heights in each facility to study experimental distortion caused by scale effects and the soundness of result extrapolation to pro- totypes. Experimental data included distributions of air concentration, air-water flow velocity, bubble frequency, bubble chord length and air-water flow turbulence intensity. For a Froude similitude, the results implied that scale effects were observed in both facilities, although the geometric scaling ratio was only Lr=2 in each case. The selection of the criterion for scale effects is a critical issue. For example, major differences (i.e. scale effects) were observed in terms of bubble chord sizes and turbulence levels al- though little scale effects were seen in terms of void fraction and velocity distributions. Overall the findings emphasize that physical modelling of stepped chutes based upon a Froude similitude is more sensitive to scale effects than classical smooth-invert chute studies, and this is consistent with basic dimensional analysis developed herein.

Joint modelling of location and scale parameters of the skew-normal distribution

Joint location and scale models of the skew-normal distribution provide useful ex- tension for joint mean and variance models of the normal distribution when the data set under consideration involves asymmetric outcomes. This paper focuses on the maximum likelihood estimation of joint location and scale models of the skew-normal distribution. The proposed procedure can simultaneously estimate parameters in the location model and the scale model. Simulation studies and a real example are used to illustrate the proposed methodologies.

Validating the Runoff from the PRECIS Model Using a Large-Scale Routing Model

The streamflow over the Yellow River basin is simulated using the PRECIS （Providing REgional Climates for Impacts Studies） regional climate model driven by 15-year （1979-1993） ECMWF reanalysis data as the initial and lateral boundary conditions and an off-line large-scale routing model （LRM）. The LRM uses physical catchment and river channel information and allows streamflow to be predicted for large continental rivers with a 1°×1° spatial resolution. The results show that the PRECIS model can reproduce the general southeast to northwest gradient distribution of the precipitation over the Yellow River basin, The PRECIS- LRM model combination has the capability to simulate the seasonal and annual streamflow over the Yellow River basin. The simulated streamflow is generally coincident with the naturalized streamflow both in timing and in magnitude.

A skew–normal mixture of joint location, scale and skewness models

Normal mixture regression models are one of the most important statistical data analysis tools in a heterogeneous population. When the data set under consideration involves asymmetric outcomes, in the last two decades, the skew normal distribution has been shown beneficial in dealing with asymmetric data in various theoretic and applied problems. In this paper, we propose and study a novel class of models： a skew-normal mixture of joint location, scale and skewness models to analyze the heteroscedastic skew-normal data coming from a heterogeneous population. The issues of maximum likelihood estimation are addressed. In particular, an Expectation-Maximization （EM） algorithm for estimating the model parameters is developed. Properties of the estimators of the regression coefficients are evaluated through Monte Carlo experiments. Results from the analysis of a real data set from the Body Mass Index （BMI） data are presented.

Experimental Study on the Ride Comfort of a Crawler Power Chassis Scale Model Based on the Similitude Theory

The ride comfort experimental assessment of crawler off-road vehicle is relatively overlooked, and is expensive and difficult to execute with higher and higher ride comfort performance requirements. To trade off between precise and cost, an experimental method based on the similitude theory is proposed. Under the guidance of the similitude theory, a 1：5 crawler power chassis scale model equipped with a kind of variable stiffness suspension system is used. The power spectrum density（PSD）, the root mean square（RMS） of weighed acceleration, peak factor, average absorbed power（AAP） and vibration dose value（VDV） are selected as ride comfort evaluation indexes, and tests results are transformed via similarity indexes to predict the performance of full-scale power chassis. PSD shows that the low-order natural frequency of the vertical natural frequency（z axis） is 1.1 Hz, and the RMS, AAP and VDV values indicate the ride comfort performance of this kind of power chassis is between the ＂A little uncomfortable＂ and ＂Rather uncomfortable＂. From the results, low-order vertical natural frequency, obtained by PSD, validates that the similarity relationship between two models is satisfied, and 1：5 scale model used in experiment meets the similarity relationship with the full-scale model; consequently, the ride comfort prophase evaluation with the 1：5 scale model is feasible. The attempt of applying the similitude theory to crawler vehicle ride comfort test study decreases the cost and improves the test feasibility with sufficient test precise.

A nonlinear k_p-ε_p particle two-scale turbulence model and its application

A particle nonlinear two-scale kp-εp turbulence model is proposed for simulating the anisotropic turbulent two-phase flow. The particle kinetic energy equation for two-scale fluctuation, particle energy transfer rate equation for large-scale fluctuation, and particle turbulent kinetic energy dissipation rate equation for small-scale fluctuation are derived and closed. This model is used to simulate gas-particle flows in a sudden-expansion chamber. The simulation is com- pared with the experiment and with those obtained by using another two kinds of tow-phase turbulence model, such as the single-scale k-ε two-phase turbulence model and the particle two-scale second-order moment （USM） two-phase turbulence model. It is shown that the present model gives simulation in much better agreement with the experiment than the single-scale k-ε two-phase turbulence model does and is almost as good as the particle two-scale USM turbu-lence model.

A Non-geometrically Similar Model for Predicting the Wake Field of Full-scale Ships

规模效果导致在模型规模和实际轮船的 wake 地之间的大差异，并且在在预言实际轮船的表演的成穴性能和令人激动的力量测试引起差别。因此，从轮船模型的测试数据是什么时候，直接使用了预言实际轮船的表演，测试结果必须受到实验修正。这研究为壳模型的反向的设计建议一个方法。比作一个几何上类似的壳模型，修改模型产生的 wake 地接近一艘实际轮船的。一非 -- 轮船和海洋工程(KRISO ) s 容器轮船(KCS ) 的一个朝鲜研究院的几何上类似的模型被设计。数字模拟用这个模型被执行，并且它的结果与照原尺寸的计算结果相比。由非几何上类似的模型得到照原尺寸的轮船的 wake 领域的变丑方法成功地被用于 KCS。

Evaluation of Subgrid-scale Models in Large-eddy Simulations of Turbulent Flow in a Centrifugal Pump Impeller

The current research of large eddy simulation （LES） of turbulent flow in pumps mainly concentrates in applying conventional subgrid-scale （SGS） model to simulate turbulent flow, which aims at obtaining the flow field in pump. The selection of SGS model is usually not considered seriously, so the accuracy and efficiency of the simulation cannot be ensured. Three SGS models including Smagorinsky-Lilly model, dynamic Smagorinsky model and dynamic mixed model are comparably studied by using the commercial CFD code Fluent combined with its user define function. The simulations are performed for the turbulent flow in a centrifugal pump impeller. The simulation results indicate that the mean flows predicted by the three SGS models agree well with the experimental data obtained from the test that detailed measurements of the flow inside the rotating passages of a six-bladed shrouded centrifugal pump impeller performed using particle image velocimetry （PIV） and laser Doppler velocimetry （LDV）. The comparable results show that dynamic mixed model gives the most accurate results for mean flow in the centrifugal pump impeller. The SGS stress of dynamic mixed model is decompose into the scale similar part and the eddy viscous part. The scale similar part of SGS stress plays a significant role in high curvature regions, such as the leading edge and training edge of pump blade. It is also found that the dynamic mixed model is more adaptive to compute turbulence in the pump impeller. The research results presented is useful to improve the computational accuracy and efficiency of LES for centrifugal pumps, and provide important reference for carrying out simulation in similar fluid machineries.

The Multi-Scale Numerical Modeling System for Research on the Relationship between Urban Planning and Meteorological Environment

Considering the urban characteristics, a customized multi-scale numerical modeling system is established to simulate the urban meteorological environment. The system mainly involves three spatial scales: the urban scale, urban sub-domain scale, and single to few buildings scale. In it, different underlying surface types are employed, the building drag factor is used to replace its roughness in the influence on the urban wind field, the effects of building distribution, azimuth and screening of shortwave radiation are added, and the influence of anthropogenic heating is also taken into account. All the numerical tests indicate that the simulated results are reasonably in agreement with the observational data, so the system can be used to simulate the urban meteorological environment. Making use of it, the characteristics of the meteorological environment from the urban to urban sub-domain scales, even the among-buildings scale, can be recognized. As long as the urban planning scheme is given, the corresponding simulated results can be obtained so as to meet the need of optimizing urban planning.

Multi-scale modeling of hemodynamics in the cardiovascular system

The human cardiovascular system is a closed- loop and complex vascular network with multi-scaled het- erogeneous hemodynamic phenomena. Here, we give a selective review of recent progress in macro-hemodynamic modeling, with a focus on geometrical multi-scale model- ing of the vascular network, micro-hemodynamic modeling of microcirculation, as well as blood cellular, subcellular, endothelial biomechanics, and their interaction with arter- ial vessel mechanics. We describe in detail the methodology of hemodynamic modeling and its potential applications in cardiovascular research and clinical practice. In addition, we present major topics for future study： recent progress of patient-specific hemodynamic modeling in clinical applica- tions, micro-hemodynamic modeling in capillaries and blood cells, and the importance and potential of the multi-scale hemodynarnic modeling.

Feasibility and simulation model of a pilot scale membrane bioreactor for wastewater treatment and reuse from Chinese traditional medicine

The lack and pollution of water resource make wastewater reuse necessary. The pilot scale long-term tests for submerged membrane bioreactor were conducted to treat the effluents of anaerobic or aerobic treatment process for the high-strength Chinese traditional medicine wastewater. This article was focused on the feasibility of the wastewater treatment and reuse at shorter hydraulic retention time （HRT） of 5.0, 3.2 and 2.13 h. MLSS growth, membrane flux, vacuum values and chemical cleaning periods were also investigated. The experimental results of treating two-phase anaerobic treatment effluent demonstrated that the CODfilt was less than 100 mg/L when the influent COD was between 500-10000 mg/L at HRT of 5.0 h, which could satisfy the normal discharged standard in China. The experimental results to treat cross flow aerobic reactor effluent demonstrated that the average value of CODfilt was 17.28 mg/L when the average value of influent COD was 192.84 mg/L at HRT of 2.13 h during 106 d, which could completely meet the normal standard for water reuse. The maximum MLSS and MLVSS reached 24000 and 14500 mg/L at HRT of 3.2 h respectively. Membrane flux had maximal resume degrees of 94.7% at vacuum value of 0.02 MPa after cleaning. Chemical cleaning periods of membrane module were 150 d. A simulation model of operational parameters was also established based on the theory of back propagation neural network and linear regression of traditional mathematical model. The simulation model showed that the optimum operational parameters were suggested as follows： HRT was 5.0 h, SRT was 100 d, the range of COD loading rate was between 10.664-20.451 kg/（m3.d）, the range of MLSS was between 7543-13694 mg/L.

Meso-scale modeling of chloride diffusion in concrete with consideration of effects of time and temperature

A meso-scale truss network model was developed to predict chloride diffusion in concrete. The model regards concrete as a three-phase composite of mortar matrix, coarse aggregates, and the interfacial transition zone （ITZ） between the mortar matrix and the aggregates. The diffusion coefficient of chloride in the mortar and the ITZ can be analytically determined with only the water-to-cement ratio and volume fraction of fine aggregates. Fick＇s second law of diffusion was used as the governing equation for chloride diffusion in a homogenous medium （e.g., mortar）; it was discretized and applied to the truss network model. The solution procedure of the truss network model based on the diffusion law and the meso-scale composite structure of concrete is outlined. Additionally, the dependence of the diffusion coefficient of chloride in the mortar and the ITZ on exposure duration and temperature is taken into account to illustrate their effect on chloride diffusion coefficient. The numerical results show that the exposure duration and environmental temperature play important roles in the diffusion rate of chloride ions in concrete. It is also concluded that the meso-scale truss network model can be applied to chloride transport analysis of damaged （or cracked） concrete.

A Multi-Scale Urban Atmospheric Dispersion Model for Emergency Management

To assist emergency management planning and prevention in case of hazardous chemical release into the atmosphere,especially in densely built-up regions with large populations,a multi-scale urban atmospheric dispersion model was established.Three numerical dispersion experiments,at horizontal resolutions of 10 m,50 m and 3000 m,were performed to estimate the adverse effects of toxic chemical release in densely built-up areas.The multi-scale atmospheric dispersion model is composed of the Weather Forecasting and Research （WRF） model,the Open Source Field Operation and Manipulation software package,and a Lagrangian dispersion model.Quantification of the adverse health effects of these chemical release events are given by referring to the U.S.Environmental Protection Agency＇s Acute Exposure Guideline Levels.The wind fields of the urban-scale case,with 3 km horizontal resolution,were simulated by the Beijing Rapid Update Cycle system,which were utilized by the WRF model.The sub-domain-scale cases took advantage of the computational fluid dynamics method to explicitly consider the effects of buildings.It was found that the multi-scale atmospheric dispersion model is capable of simulating the flow pattern and concentration distribution on different scales,ranging from several meters to kilometers,and can therefore be used to improve the planning of prevention and response programs.

A two-scale second-order moment two-phase turbulence model for simulating dense gas-particle flows

A two-scale second-order moment two-phase turbulence model accounting for inter-particle collision is developed, based on the concepts of particle large-scale fluctuation due to turbulence and particle small-scale fluctuation due to collision and through a unified treatment of these two kinds of fluctuations. The proposed model is used to simulate gas-particle flows in a channel and in a downer. Simulation results are in agreement with the experimental results reported in references and are near the results obtained using the sin- gle-scale second-order moment two-phase turbulence model superposed with a particle collision model （USM-θ model） in most regions.

Prediction of Vibration Characteristics in Beam Structure Using Sub-Scale Modeling with Experimental Validation

Geometric or sub-scale modeling techniques are used for the evaluation of large and complex dynamic structures to ensure accurate reproduction of load path and thus leading to true dynamic characteristics of such structures. The sub-scale modeling technique is very effective in the prediction of vibration characteristics of original large structure when the experimental testing is not feasible due to the absence of a large testing facility. Previous researches were more focused on free and harmonic vibration case with little or no consideration for readily encountered random vibration. A sub-scale modeling technique is proposed for estimating the vibration characteristics of any large scale structure such as Launch vehicles, Mega structures, etc., under various vibration load cases by utilizing precise scaled-down model of that dynamic structure. In order to establish an analytical correlation between the original structure and its scaled models, different scale models of isotropic cantilever beam are selected and analyzed under various vibration conditions（ i.e. free, harmonic and random） using finite element package ANSYS. The developed correlations are also validated through experimental testing The prediction made from the vibratory response of the scaled-down beam through the established sets of correlation are found similar to the response measured from the testing of original beam structure. The established correlations are equally applicable in the prediction of dynamic characteristics of any complex structure through its scaled-down models. This paper presents modified sub-scale modeling technique that enables accurate prediction of vibration characteristics of large and complex structure under not only sinusoidal but also for random vibrations.

A Simulating Study on Resolvable-Scale Microphysical Parameterization in a Mesoscale Model

The Penn State/ NCAR Mesoscale Model (MM5) is used to simulate the precipitation event that occurred during 1–2 May 1994 to the south of the Yangtze River. In five experiments the Kain–Fritsch scheme is made use of for the subgrid–scale convective precipitation, but five different resolvable–scale microphysical parameterization schemes are employed. They are the simple super-saturation removal scheme, the warm rain scheme of Hsie et al. (1984), the simple ice scheme of Dudhia (1989), the complex mixed–phase scheme developed by Reisner et al. (1993), and the GSFC microphysical scheme with graupel. Our interest is how the various resolvable-scale schemes affect the domain-averaged precipitation, the precipitation distribution, the sea level pressure, the cloud water and the cloud ice. Through a series of experiments about a warm sector rainfall case, results show that although the different resolvable-scale scheme is used, the differences of the precipitation characteristics among all five runs are not very obvious. However, the precipitation is over-predicted and the strong mesoscale low is produced by the simple super-saturation removal scheme. The warm rain scheme with the inclusion of condensation and evaporation under-predicts the precipitation and allows the cloud water to reach the 300 hPa level. The scheme of the addition of graupel increases the resolvable-scale precipitation by about 20%-30%. The inclusion of supercooled liquid water in the grid-scale scheme does not affect significantly the results. Key words Mesoscale model - Precipitation - Resolvable-scale microphysical parameterization