Investigation of bubbles escape behavior from low basicity mold flux for high-Mn high-Al steels using 3D X-ray microscope

During the continuous casting process of high-Mn high-Al steels,various types of gases such as Ar need to escape through the top of the mold.In which,the behavior of bubbles traversing the liquid slag serves as a restrictive link,closely associated with viscosity and the thickness of liquid slag.In contrast to two-dimensional surface observation,three-dimensional(3D)analysis method can offer a more intuitive,accurate,and comprehensive information.Therefore,this study employs a 3D X-ray microscope(3D-XRM)to obtained spatial distribution and 3D morphological characteristics of residual bubbles in mold flux under different basicity of liquid slag,different temperatures,and different holding times.The results indicate that as basicity of slag increases from 0.52 to 1.03,temperature increases from 1423 to 1573 K,the viscosity of slag decreases,the floating rate of bubbles increases.In addition,when holding time increases from 10 to 30 s,the bubbles floating distance increases,and the volume fraction and average equivalent sphere diameter of the bubbles solidified in the mold flux gradually decreases.In one word,increasing the basicity,temperature,and holding time leading to an increase in the removal rate of bubbles especially for the large.These findings of bubbles escape behavior provide valuable insights into optimizing low basicity mold flux for high-Mn high-Al steels.

Water-Assisted Injection Molding System Based on Water Hydraulic Proportional Control Technique

Water-assisted injection molding（WAIM）, an innovative process to mold plastic parts with hollow sections, is characterized with intermittent, periodic process and large pressure and flow rate variation. Energy savings and injection pressure control can not be .attained based on conventional valve control system. Moreover, the injection water can not be supplied directly by water hydraulic proportional control system. Poor efficiency and control performance are presented by current trial systems, which pressurize injection water by compressed air. In this paper, a novel water hydraulic system is developed applying an accumulator for energy saving. And a new differential pressure control method is proposed by using pressure cylinder and water hydraulic proportional pressure relief valve for back pressure control. Aiming at design of linear controller for injection water pressure regulation, a linear load model is approximately built through computational fluid dynamics（CFD） simulation on two-phase flow cavity filling process with variable temperature and viscosity, and a linear model of pressure control system is built with the load model and linearization of water hydraulic components. According to the simulation, model based feedback is brought forward to compensate the pressure decrease during accumulator discharge and eliminate the derivative element of the system. Meanwhile, the steady-state error can be reduced and the capacity of resisting disturbance can be enhanced, by closed-loop control of load pressure with integral compensation. Through the developed experimental system in the State Key Lab of Fluid Power Transmission and Control, Zhejiang University, China, the static characteristic of the water hydraulic proportional relief valve was tested and output pressure control of the system in Acrylonitrile Butadiene Styrene（ABS） parts molding experiments was also studied. The experiment results show that the dead band and hysteresis of the water hydraulic proportional pressure relief valve are large, but the control precision and linearity can be improved with feed-forward compensation. With the experimental results of injection water pressure control, the applicability of this WAIM system and the effect of its linear controller are verified. The novel proposed process of WAIM pressure control and study on characteristics of control system contribute to the application of water hydraulic proportional control and WAIM technology.

Shear-thinning behavior of the CaO–SiO2–CaF2–Si3N4 system mold flux and its practical application

Satisfying the mold-flux performance requirements for high-speed continuous casting necessitates the development of a new non-Newtonian-fluid mold flux with shear-thinning behavior, i.e., a mold flux whose viscosity is relatively high under lower shear rates and relatively low under higher shear rates. In this work, a mold flux that exhibits shear-thinning behavior was developed by adding different amounts of Si_3N_4 to the CaO–SiO_2–CaF_2 mold flux. The shear-thinning behavior was investigated using a rotational viscometer. In addition, the microstructure of the newly prepared slags was studied by high-temperature Raman spectroscopy and X-ray photoelectron spectroscopy. The results showed that the mechanism of shear-thinning was attributable to a temporary viscosity loss caused by the one-way shear stress, whereas the corresponding magnitude of shear-thinning was closely related to the degree of polymerization(DP). Finally, the non-Newtonian fluid mold flux was used for laboratory casting tests, which revealed that the mold flux could reduce slag entrapment and positively affect the continuous casting optimization.

Diagnosis parameters of mold filling pattern for optimization of a casting system

For optimal design of a gating system,the setting of diagnosis parameters is very important.In this study,the permanent mold casting process was selected because most of the other casting processes have more complicated factors that influence the mold filling pattern compared to the permanent mold casting process,such as the surface roughness of mold,gas generation from the mold wash and binder of sand mold,and the gas permeability through a sand mold,etc.Two diagnosis parameters(flow rate difference and arrival time difference) of molten metal flow pattern in the numerical simulation are suggested for design of an optimum casting system with a permanent mold.The results show that the arrival time difference can be used as one important diagnosis parameter of the complexity of the runner system and its usefulness has been verified via making aluminum parts using permanent mold casting(Fig.9).

A model for mold collaborative manufacturing execution system based on Web Service

Mold manufacturing Extended Enterprise （EE） has the following characteristics： distributed in locality, tight cooperation and frequent information exchange. It needs a collaborative, highly efficient, reliable and intelligent manufacturing management system. The background of the Collaborative Manufacturing is introduced. A mold Collaborative Manufacturing Execution System （c-MES） is proposed. The feature of Web Service platform is analyzed. The necessity and feasibility of importing the Web Service to mold c-MES are discussed. Based on Web Service, the model of mold c-MES is built. Every module＇ s function is described in detail, including the functions it supplies and the mechanism of information interaction among them. The feasibility of mold c-MES model is validated by a real mold manufacturing case.

Characteristics and influence factors of mold filling process in permanent mold with a slot gating system

The main problems caused by improper gating are entrained aluminum oxide films and entrapped gas.In this study,the slot gating system is employed to improve mold filling behavior and therefore,to improve the quality of aluminum castings produced in permanent molds.An equipment as well as operation procedures for real-time X-ray radiography of molten aluminum flowing into permanent molds have been developed.Graphite molds transparent to X-rays are utilized which make it possible to observe the flow pattern through a number of vertically oriented gating systems.The investigation discovers that there are many influencing factors on the mold filling process.This paper focuses its research on some of the factors,such as the dimensions of the vertical riser and slot thickness,as well as roughness of the coating layer.The results indicate that molten metal can smoothly fill into casting cavity with a proper slot gating system.A bigger vertical riser,proper slot thickness and rougher coating can provide not only a better mold filling pattern,but also hot melt into the top of the cavity.A proper temperature gradient is obtainable,higher at the bottom and lower at the top of the casting cavity,which is in favor of feeding during casting solidification.

Study of Weak Acid Preservatives and Modified Atmosphere Packaging (MAP) on Mold Growth in Modal Agar System

Inhibition of spoilage mold of common contaminant of bakery goods in modal agar system by potassium sorbate and calcium propionate in wide range of concentration (0 - 2000 ppm) at different pH (5.5 - 7) was investigated. All Samples were examined daily for mold growth. Results showed that both potassium sorbate and calcium propionate can be used effectively to inhibit mold growth and the effectiveness of these preservatives is enhanced by increasing the concentration and decreasing the pH. The effect of modified atmosphere packaging (MAP) comprised of 60% or 80% CO2 (balance N2) and oxygen absorbents on the growth of mold was also studied on the agar system. The results indicated that mold growth was prevented up to 42 days in packs flushed with 60% or 80% CO2 (balance N2). It was also evident that all samples did not show mold growth for >40 days when packaged in the presence of oxygen scavenger sachet.

基于MoldFlow太阳能储能系统下盖成型模拟及应用

以太阳能储能系统下盖模流分析为例,反复修改流道和浇口截面尺寸与长度以及主流道位置,确定流道尺寸。运用MoldFlow对设计好的流道进行充填分析,以使成型达到流动平衡,并进行冷却、翘曲分析,预测成型缺陷,提出解决措施,为模具设计提供浇注系统和冷却系统方案和注射成型工艺参数,并应用于模具设计和实际生产。

An innovative tester system for measuring mechanical property of foundry molding sand

A new intelligent tester system for measuring multiple mechanical properties of foundry molding sand is introduced and has been patented for the invention in China. The testing process can be simultaneously controlled with a build-in chip microcomputer communicating with a PC through a serial port. The testing system applies dynamic testing technology. During the measurement for compression, relaxation, shearing and tensile processes of sand specimens, the corresponding characteristic curves and eight mechanical property parameters can be obtained in a short time, simply by consecutively testing on four sand specimens. The properties and parameters to be measurable by the tester include compressive strength, elastic modulus, plastic deformation threshold, springback potential, shear strength, shear deformation limit, toughness and tensile strength. These properties and parameters for sand specimens can be defined as the corresponding characteristic curves with precise physical meanings, carried out by the tester, Two of them, namely plastic deformation threshold and springback potential, as well as their testing methods, have been invented for the first time. The testing system applying advanced data measurement technology as well as performing excellent functions is an important breakthrough and creativity in foundry molding sand property testing field. The parameters acquired by the testing system are stable, accurate and reliable. The test data can be instantly displayed or printed out or stored in the PC. As evidence, many experimental data obtained by the tester practically from both laboratory and foundry floor tests indicate that the tester system can be widely applied in foundry industry.

Development of Integrated Simulation System for Plastic Injection Molding

Numerical simulation of injection molding have had success in predicting the behavior of polymer melt in extremely complicated geometries. Most of the current numerical solutions are based on finite-element/finite-difference/boundary-element/volume-control methods and the surface model. This paper discusses the development of an integrated CAE system for injection molding in detail, and presents the mathematics for numerical simulation of filling, packing, cooling, stress and warpage in injection molding. The developed system named as HsCAE3D is introduced at the end.

Development of a plastic injection molding training system using Petri nets and virtual reality

In this study, Virtual Reality (VR)-based plastic injection molding training system (VPIMTS), which can be modeled as an integrated system with a task planning module, an intelligent instruction module, a simulation module, and virtual envi-ronment (VE) module, was developed. Presented in this paper are an architecture of VPIMTS, a practical knowledge modelling approach for modelling the training scenarios of the system by using Petri nets formalism and key techniques (FEM, injection molding procedure modelling) which have been developed independently. The utilization of the Petri net model realized the environment where the trainee can behave freely, and also made it possible to equip the system with the function of showing the next action of the trainee whenever he wants. The overall system is a powerful approach for highly improving the trainee’s comprehension and injection molding study-efficiency by building digital, intelligent, knowledgeable, and visual aids.

Development of Online Machining and Measurement System in Die and Mold Manufacturing： Concept and Fundamental Experiments

The corrective machining to compensate the resulting errors is usually tried at plural times based on the trial-and-error process when the machining is realized in die and mold manufacturing. This corrective machining has an influence on accuracy and efficiency and is an important factor. The measurement system for measuring the forms of die and mold at all times is essential in order to machine the die and mold with high accuracy and efficiency. However, the problems of management and operation errors are found in compensating process of die and mold machining. In this paper, an online machining and measurement system in die and mold manufacturing is developed in order to overcome these problems. In this online system, 2-axis control system is added to a surface roughness measuring instrument, and both NC machining program and measured data are linked and controlled using a same computer. Therefore, the machining and measurement can be recognized for consistent process, and can be realized on the machine. This system has the advantages such as the high accuracy, low-price, and online convenience and so on. The possibility of practical use of this online system was investigated by fundamental experiments.

Irregular initial solidification by mold thermal monitoring in the continuous casting of steels:A review

Occasional irregular initial solidification phenomena,including stickers,deep oscillation marks,depressions,and surface cracks of strand shells in continuous casting molds,are important limitations for developing the high-efficiency continuous casting of steels.The application of mold thermal monitoring(MTM) systems,which use thermocouples to detect and respond to temperature variations in molds,has become an effective method to address irregular initial solidification phenomena.Such systems are widely applied in numerous steel companies for sticker breakout prediction.However,monitoring the surface defects of strands remains immature.Hence,indepth research is necessary to utilize the potential advantages and comprehensive monitoring of MTM systems.This paper summarizes what is included in the irregular initial solidification phenomena and systematically reviews the current state of research on these phenomena by the MTM systems.Furthermore,the influences of mold slag behavior on monitoring these phenomena are analyzed.Finally,the remaining problems of the formation mechanisms and investigations of irregular initial solidification phenomena are discussed,and future research directions are proposed.

Effects of the Water-Cement Ratio and the Molding Temperature on the Hydration Heat of Cement

The effects of the water-cement ratio and the molding temperature on the hydration heat of cement were investigated with semi-adiabatic calorimetry.The specimens were prepared with water-cement ratios of 0.31,0.38,and 0.45,and the molding temperature was specified at 10 and 20℃.The experimental results show that,as the water-binder ratio increases,the value of the second temperature peak on the temperature curve of the cement paste decreases,and the age at which the peak appears is delayed.The higher the water-cement ratio,the higher the hydration heat release in the early period of cement hydration,but this trend reverses in the late period.There are intersection points of the total hydration heat curve of the cement pastes under the influence of the water-cement ratio,and this law can be observed at both molding temperatures.With the increase in the molding temperature,the age of the second temperature peak on the temperature curve of the cement paste will advance,but the temperature peak will decrease.The higher the molding temperature,the earlier the acceleration period of the cement hydration began,and the larger the hydration heat of the cement in the early stage,but the smaller the total heat in the late period.A subsection function calculation model of the hydration heat,which was based on the existing models,was proposed in order to predict the heat of the hydration of the concrete.

Oxygen variation in titanium powder and metal injection molding

The control of oxygen is paramount in achieving high-performance titanium(Ti)parts by powder metallurgy such as metal in-jection molding(MIM).In this study,we purposely selected the Ti and Ti-6Al-4V powders as the reference materials since these two are the most representative Ti materials in the industry.Herein,hydride-dehydride(HDH)Ti powders were pre-oxidized to examine the ef-fect of oxygen variation on the characteristics of oxide layer on the particle surface and its resultant color feature.The results indicate that the thickness and Ti oxide level(Ti^(0)→Ti^(4+))of the oxide layer on the HDH Ti powders increased as the oxygen content increased,lead-ing to the transition of color appearance from grey,brown to blue.This work aids in the powder feedstock selection at the initial stage in powder metallurgy.In addition,the development of oxygen content was comprehensively studied during the MIM process using the gas-atomized(GA)Ti-6Al-4V powders.Particularly,the oxygen variation in the form of oxide layer,the change of oxygen content in the powders,and the relevant parts were investigated during the processes of kneading,injection,debinding,and sintering.The oxygen vari-ation was mainly concentrated in the sintering stage,and the content increased with the increase of sintering temperature.The variation of oxygen content during the MIM process demonstrates the crucial role of powder feedstock and sintering stage in controlling oxygen con-tent.This work provides a piece of valuable information on oxygen detecting,control,and manipulation for the powder and processing in the industry of Ti and its alloys by powder metallurgy.

Numerical simulation study on the mold strength of magnetic mold casting based on a coupled electromagnetic-structural method

The properties of the magnetic mold in magnetic mold casting directly determine the quality of the final cast parts.In this study,the magnetic mold properties in magnetic mold casting,were studied utilizing a coupled electromagnetic-structural method through numerical simulation.This study investigated key factors including equivalent stress,the distribution of tensile and compressive stresses,and the area ratio of tensile stress.It compared molds made entirely of magnetic materials with those made partially of magnetic materials.Simulation results indicate that as current increases from 4 A to 8 A,both the initial magnetic mold and the material-replaced magnetic mold initially show an increasing trend in equivalent stress,tensile-compressive stress,and the area ratio of tensile stress,peaking at 6 A before declining.After material replacement,the area ratio of tensile stress at 6 A decreases to 19.84%,representing a reduction of 29.72%.Magnetic molds comprising a combination of magnetic and non-magnetic materials exhibit sufficient strength and a reduced area ratio of tensile stress compared to those made entirely from magnetic materials.This study provides valuable insights for optimizing magnetic mold casting processes and offers practical guidance for advancing the application of magnetic molds.

Elimination of cracks in stainless steel casings via 3D printed sand molds with an internal topology structure

The important supporting component in a gas turbine is the casing,which has the characteristics of large size,complex structure,and thin wall.In the context of existing 3DP sand casting processes,casting crack defects are prone to occur.This leads to an increase in the scrap rate of casings,causing significant resource wastage.Additionally,the presence of cracks poses a significant safety hazard after the casings are put into service.The generation of different types of crack defects in stainless steel casings is closely related to casting stress and the high-temperature concession of the sand mold.Therefore,the types and causes of cracks in stainless steel casing products,based on their structural characteristics,were systematically analyzed.Various sand molds with different internal topology designs were printed using the 3DP technology to investigate the impact of sand mold structures on high-temperature concession.The optimal sand mold structure was used to cast casings,and the crack suppression effect was verified by analyzing its eddy current testing results.The experimental results indicate that the skeleton structure has an excellent effect on suppressing cracks in the casing.This research holds important theoretical and engineering significance in improving the quality of casing castings and reducing production costs.

Management of Strawberry Grey Mold Disease Using Biocontrol Agents and Plant Extracts

Strawberry (Fragaria × ananassa Duch.) is a significant global soft fruit crop, prized for its nutrient content and pleasant flavor. However, diseases, particularly grey mold caused by Botrytis cinerea Pers. Fr. poses major constraints to strawberry production and productivity. Grey mold severely impacts fruit quality and quantity, diminishing market value. This study evaluated five B. cinerea isolates from various locations in the Ri-Bhoi district of Meghalaya. All isolates were pathogenic, with isolate SGM 2 identified as highly virulent. Host range studies showed the pathogen-producing symptoms in the fava bean pods, marigold, gerbera, and chrysanthemum flowers and in the fava bean, gerbera, and lettuce leaves. In vitro tests revealed that neem extract (15% w/v) achieved the highest mycelial growth inhibition at 76.66%, while black turmeric extract (5% w/v) had the lowest inhibition at 9.62%. Dual culture methods with bio-control agents indicated that Bacillus subtilis recorded the highest mean inhibition at 77.03%, while Pseudomonas fluorescens had the lowest at 20.36% against the two virulent isolates. Pot evaluations demonstrated that B. subtilis resulted in the lowest percent disease index at 20.59%, followed by neem extract at 23.31%, with the highest disease index in the control group at 42.51%. Additionally, B. subtilis significantly improved plant growth, yielding an average of 0.32 kg compared to 0.14 kg in the control. The promising results of B. subtilis and neem leaf extract from this study suggest their potential for eco-friendly managing grey mold in strawberries under field conditions.

Dependence of Lower Molding Temperature Limit and Molding Time on Molding Mechanism in Dental Thermoforming

Effectiveness and safety of a sports mouthguard depend on its thickness and material, and the thermoforming process affects these. The purpose of this study was to clarify the effects of differences in molding mechanisms on the lower molding temperature limit and molding time in dental thermoforming. Ethylene vinyl acetate resin mouthguard sheet and two thermoforming machines;vacuum blower molding machine and vacuum ejector/pressure molding machine were used. The molding pressures for suction molding were −0.018 MPa for vacuum blower molding and −0.090 MPa for vacuum ejector molding, and for pressure molding was set to 0.090 MPa or 0.450 MPa. Based on the manufacturer’s standard molding temperature of 95˚C, the molding temperature was lowered in 2.5˚C increments to determine the lower molding temperature limit at which no molding defects occurred. In order to investigate the difference in molding time depending on the molding mechanism, the duration of molding pressure was adjusted in each molding machine, and the molding time required to obtain a sample without molding defects was measured. The molding time of each molding machine were compared using one-way analysis of variance. The lower molding temperature limit was 90.0˚C for the vacuum blower machine, 77.5˚C for the vacuum ejector machine, 77.5˚C for the pressure molding machine at 0.090 MPa, and 67.5˚C for the pressure molding machine at 0.45 MPa. The lower molding temperature limit was higher for lower absolute values of molding pressure. The molding time was shorter for pressure molding than for suction molding. Significant differences were observed between all conditions except between the pressure molding machine at 0.090 MPa and 0.45 MPa (P < 0.01). A comparison of the differences in lower molding temperature limit and molding time due to molding mechanisms in dental thermoforming revealed that the lower molding temperature limit depends on the molding pressure and that the molding time is longer for suction molding than for pressure molding.

Non-Darcy Flow in Molding Sands

Darcy’s law is widely used to describe the flow in porous media in which there is a linear relationship between fluid velocity and pressure gradient. However, it has been found that for high numbers of Reynolds this law ceases to be valid. In this work, the Ergun equation is employed to consider the non-linearity of air velocity with the pressure gradient in casting sands. The contribution of non-linearity to the total flow in terms of a variable defined as a non-Darcy flow fraction is numerically quantified. In addition, the influence of the shape factor of the sand grains on the non-linear flow fraction is analyzed. It is found that for values of the Reynolds number less or equal than 1, the contribution of non-linearity for spherical particles is around 1.15%.