Non-Darcy Flow in Molding Sands

Darcy’s law is widely used to describe the flow in porous media in which there is a linear relationship between fluid velocity and pressure gradient. However, it has been found that for high numbers of Reynolds this law ceases to be valid. In this work, the Ergun equation is employed to consider the non-linearity of air velocity with the pressure gradient in casting sands. The contribution of non-linearity to the total flow in terms of a variable defined as a non-Darcy flow fraction is numerically quantified. In addition, the influence of the shape factor of the sand grains on the non-linear flow fraction is analyzed. It is found that for values of the Reynolds number less or equal than 1, the contribution of non-linearity for spherical particles is around 1.15%.

Numerical Study on the Resin Transfer Molding Curing Process for Thick Composites Materials

The successful manufacture of thick composites is challenging since the highly exothermic nature of thermoset resins and limited temperature control make avoiding the onset of detrimental thermal gradients within the composite relatively difficult.This phenomenon is mainly caused by exothermic heat reactions.The so-called Michaud's model has been largely used in the literature to reduce the gap between experience and simulation with regard to the effective prediction of the temperature cycle in these processes.In this work,another solution is proposed to simulate the curing process for thick composites,namely preheating the resin to activate the curing reaction before resin injection into the mold.A good agreement between the experiment and the simulation is found.Moreover,in order to minimize the thermal gradient in the final composite,the thermophysical properties of the fiber and the torque(temperature,time)of the Plate have been varied leading to interesting results.

Effect of Molding Technique That Move Model Position Just before Formation in Production of Laminated Mouthguard

Many molding techniques have been researched to ensure the thickness of custom mouthguards. The aim of this study was to clarify the effect on the thickness of a laminated mouthguard of a molding technique in which the model position is moved forward just before molding. Mouthguards were molded using a 3.0-mm-thick ethylene vinyl acetate mouthguard sheet and a pressure molding machine. The molding method was the normal molding method (condition C) and the molding technique (condition MP) in which the model position was moved 20 mm forward just before molding. Regarding the molding of the first layer (F) and the second layer (S), the following four molding methods based on the combination of conditions C and MP were compared;FC-SC, FC-SMP, FMP-SC, and FMP-SMP. Differences in mouthguard thickness due to molding conditions for the first and second layers were analyzed by two-way ANOVA and Bonferroni’s multiple comparison test. Significant differences were observed among all molding conditions on the labial surface, and the thicknesses were in the order FC-SC < FC-SMP < FMP-SC < FMP-SMP. FMP-SMP was 4.67 mm thick, which was 1.39 mm thicker than FC-SC. FC-SC was the thinnest at the cusp, and a significant difference was observed between other molding conditions. On the buccal side, significant differences were observed between all conditions except FC-SMP and FMP-SC, and the thicknesses were in the order FC-SC < FC-SMP, FMP-SC < FMP-SMP. The results of this study suggested that the labial and buccal sides of laminated mouthguards could be made 1.4 and 1.2 times thicker when a molding technique that moves the model position just before formation was used for the first and second layers. The reduction in thickness was suppressed by approximately 23.2% and approximately 10.7% on the labial and buccal sides, respectively, compared with the normal molding method.

Pro／E中Molding模块在注塑模具设计中的应用

主要介绍利用Pro／E中Molding模块进行注塑模具设计的基本步骤，并通过实例，讲述利用Pro／E进行注塑模具设计的基本流程，从而为模具的设计开发降低了成本，提高了质量，并为设计人员提供了重要的研究开发工具。

Powder injection molding of pure titanium

An improved wax-based binder was developed for powder injection molding of pure titanium. A critical powder loading of 69 vol.% and a pseudo-plastic flow behavior were obtained by the feedstock based on the binder. The injection molding, debinding, and sintering process were studied. An ideal control of carbon and oxygen contents was achieved by thermal debinding in vacuum atmosphere （10^-3 Pa）. The mechanical properties of as-sintered specimens were less than those of titanium made by the conventional press-sintering process. Good shape retention and ±0.04 mm dimension deviation were achieved.

A strategy to obtain a high-density and high-strength zirconia ceramic via ceramic injection molding by the modification of oleic acid

Despite its unique high efficiency and good environmental compatibility, the water-soluble binder system still encounters problems achieving a desired sintered part via ceramic injection molding because of the poor compatibility and the powder-binder segregation between ceramic powders and binders. The objective of this study was to obtain a sintered part with excellent properties by introducing a small quantity of oleic acid to the surface of zirconia powders before the mixing process. As opposed to many previous investigations that focused only on the rheological behavior and modification mechanism, the sintering behavior and densification process were systematically investigated in this study. With the modified powders, debound parts with a more homogeneous and smaller pore size distribution were fabricated. Also, a higher density and greater flexural strength were achieved in the sintered parts fabricated using the modified powders.

NUMERICAL SIMULATION OF FEEDSTOCK MELT FILLING IN A CYLINDRICAL CAVITY WITH SOLIDIFICATION IN POWDER INJECTION MOLDING

ＩＮＴＲＯＤＵＣＴＩＯＮＰｏｗｄｅｒｉｎｊｅｃｔｉｏｎｍｏｌｄｉｎｇ（ＰＩＭ）ｉｓａｐｒｏｃｅｓｉｎｇｒｏｕｔｅｆｏｒｆａｂｒｉｃａｔｉｎｇｍｅｔａｌｏｒｃｅｒａｍｉｃｃｏｍｐｏｎｅｎｔｓｗｉｔｈｃｏｍｐｌｅｘｓｈａｐｅａｎｄｈｉｇｈｐｅｒｆｏｒ?..

Preparation of liquefied wood-based resins and their application in molding material

To investigate value in use of liquefied wood-based resin applications in molding material, Chinese fir （Cunninghamia lanceolata） and poplar （Populus tomentosa） wood meal were liquefied in phenol. The reactant was co-condensed with formaldehyde to obtain liquefied wood-based resin. For this paper, we investigated the characterization of the resin and its application in molding material. The result shows that the basic properties of liquefied wood-based resin were satisfactory; the bonding strength of plywood prepared with liquefied Chinese fir and liquefied poplar resin can reach 1.54 and 1.00 MPa, respectively. The compression strengths of the molding material prepared with two kinds of liquefied wood resin were 73.01 and 73.58 MPa, almost the same as that of PF resin molding material. The limiting volume swelling of molding material made with liquefied Chinese resin and liquefied poplar resin were 8.5% and 8.3%, thickness swelling rates of water absorption were 3.3% and 4.2%, and the maximum weight ratios of water absorption were 25.9% and 26.2%, respectively. The soil burial test result shows that the weight loss rate of the molding materials made with liquefied Chinese resin and liquefied poplar resin were 8.3% and 9.1% and that of the PF resin molding material was 7.9%. After the soil internment test, the reduction ratio of compression strength of the two kinds of molding material achieved 16.9% and 17.7%, while that of the PF resin molding material was 15.4%. The test results of wood fungi inoculation on the three surfaces of the molding material indicate the breeding rate of molding material prepared with liquefied Chinese resin and liquefied poplar resin were at level 4 and that of PF resin molding material was at level 1 of the ISO standard.

Structural Scheme Optimization Design for the Stationary Platen of a Precision Plastic Injection Molding Machine

The current development of precision plastic injection molding machines mainly focuses on how to save material and improve precision, but the two aims contradict each other. For a clamp unit, clamping precision improving depends on the design quality of the stationary platen. Compared with the parametric design of stationary platen, structural scheme design could obtain the optimization model with double objectives and multi-constraints. In this paper, a SE-160 precision plastic injection molding machine with 1600 kN clamping force is selected as the subject in the case study. During the motion of mold closing and opening, the stationary platen of SE-160 is subjected to a cyclic loading, which would cause the fatigue rupture of the tie bars in periodically long term operations. In order to reduce the deflection of the stationary platen, the FEA method is introduced to optimize the structure of the stationary platen. Firstly, an optimal topology model is established by variable density method. Then, structural topology optimizations of the stationary platen are done with the removable material from 50%, 60% to 70%. Secondly, the other two recommended optimization schemes are given and compared with the original structure. The result of performances comparison shows that the scheme II of the platen is the best one. By choosing the best alternative, the volume and the local maximal stress of the platen could be decreased, corresponding to cost-saving material and better mechanical properties. This paper proposes a structural optimization design scheme, which can save the material as well as improve the clamping precision of the precision plastic injection molding machine.

Water-Assisted Injection Molding System Based on Water Hydraulic Proportional Control Technique

Water-assisted injection molding（WAIM）, an innovative process to mold plastic parts with hollow sections, is characterized with intermittent, periodic process and large pressure and flow rate variation. Energy savings and injection pressure control can not be .attained based on conventional valve control system. Moreover, the injection water can not be supplied directly by water hydraulic proportional control system. Poor efficiency and control performance are presented by current trial systems, which pressurize injection water by compressed air. In this paper, a novel water hydraulic system is developed applying an accumulator for energy saving. And a new differential pressure control method is proposed by using pressure cylinder and water hydraulic proportional pressure relief valve for back pressure control. Aiming at design of linear controller for injection water pressure regulation, a linear load model is approximately built through computational fluid dynamics（CFD） simulation on two-phase flow cavity filling process with variable temperature and viscosity, and a linear model of pressure control system is built with the load model and linearization of water hydraulic components. According to the simulation, model based feedback is brought forward to compensate the pressure decrease during accumulator discharge and eliminate the derivative element of the system. Meanwhile, the steady-state error can be reduced and the capacity of resisting disturbance can be enhanced, by closed-loop control of load pressure with integral compensation. Through the developed experimental system in the State Key Lab of Fluid Power Transmission and Control, Zhejiang University, China, the static characteristic of the water hydraulic proportional relief valve was tested and output pressure control of the system in Acrylonitrile Butadiene Styrene（ABS） parts molding experiments was also studied. The experiment results show that the dead band and hysteresis of the water hydraulic proportional pressure relief valve are large, but the control precision and linearity can be improved with feed-forward compensation. With the experimental results of injection water pressure control, the applicability of this WAIM system and the effect of its linear controller are verified. The novel proposed process of WAIM pressure control and study on characteristics of control system contribute to the application of water hydraulic proportional control and WAIM technology.

A review of the techniques for the mold manufacturing of micro/nanostructures for precision glass molding

Micro/nanostructured components play an important role in micro-optics and optical engineering,tribology and surface engineering,and biological and biomedical engineering,among other fields.Precision glass molding technology is the most efficient method of manufacturing micro/nanostructured glass components,the premise of which is meld manufacturing with complementary micro/nanostructures.Numerous mold manufacturing methods have been developed to fabricate extremely small and high-quality micro/nanostructures to satisfy the demands of functional micro/nanostructured glass components for various applications.Moreover,the service performance of the mold should also be carefully considered.This paper reviews a variety of technologies for manufacturing micro/nanostructured molds.The authors begin with an introduction of the extreme requirements of mold materials.The following section provides a detailed survey of the existing micro/nanostructured mold manufacturing techniques and their corresponding mold materials,including nonmechanical and mechanical methods.This paper concludes with a detailed discussion of the authors recent research on nickel-phosphorus(Ni-P)mold manufacturing and its service performance.

Investigation on the Moldability of HDDR NdFeB Bonded Magnet Prepared by Compression Molding Method

The phenomenon of uneven density distribution is inevitable in the process of preparing bonded magnets with complicated shape or with large geometric size by compression molding due to the friction among magnetic powder grains and between magnetic powder and the die wall, which reduces the pressure along the compression direction. In order to improve the density distribution homogeneity, the thin wall rings with composition of HDDR NdFeB prepared by compression molding were selected as the investigated object in this study. It was systematically investigated on the effect of addition level of lubricants and the addition methods of lubricants and strengthener on magnet density, density distribution and on magnet strength. By means of joint addition of lubricants and strengthener, which increases the magnet density and improves the magnet density distribution under the precondition of keeping the magnet strength unreduced. Thus the moldability of the bonded magnets is improved.

Injection molding of micro-porous titanium alloy with space holder technique

The powder space holder （PSH） and powder injection molding （PIM） methods have an industrial competitive advantage because they are capable of the net-shape production of micro-sized porous parts. In this study, micro-porous Ti6Al4V alloy （Ti64） parts were produced by the PSH-PIM process. Ti64 alloy powder and spherical polymethylrnethacrylate （PMMA） particles were used as a space holder material. After molding, binder debinding was performed by thermal method under inert gas. Debinded samples were sintered at 1250℃ for 60min in a vacuum （10-4 Pa）. Metallographic studies were conducted to determine densification and the corresponding microstructural changes. The surface of sintered samples was examined by SEM. The compressive stress and elastic modulus of the rificro-porous Ti64 samples were determined. The effects of fraction of PMMA on the properties of sintered micro-porous Ti64 alloy samples were investigated. It was shown that the fraction of PMMA could be controlled to affect the properties of the Ti alloy.

Powder injection molding of Fe-Ni soft magnetic alloys

With miniaturization and complication of the shape of electronic devices in recent years, powder injection molding (PIM) seems to be a suitable process for fabricating the higher performance soft magnetic components. In this paper, high quality Fe-50Ni soft magnetic alloy was fabricated by PIM with carbonyl iron and nickel, and the effect of sintering process on its microstructure and magnetic properties were investigated. The mechanical and magnetic properties can be obviously improved by increasing the sintering temperature or using the hydrogen atmosphere instead of high vacuum, which causes by the increase of grain size and the densification. At the optimum sintering conditions, the PIM Fe-50Ni soft magnetic alloy with high properties are obtained, whose relative density, tensile strength, Bm, Hc, μm are 97%, 465 MPa, 1.52 T, 16.62 A·m-1, 42.5 mH·m-1, respectively.

Interfacial microstructure and mechanical properties of Ti-6Al-4V/Al7050 joints fabricated using the insert molding method

Ti-6Al-4V/Al7050 joints were fabricated by a method of insert molding and corresponding interfacial microstructure and mechanical properties were investigated. The interfacial thickness was sensitive to holding temperature during the first stage, and a good metallurgical bonding interface with a thickness of about 90 μm can be obtained at 750°C. X-ray diffraction, transmission electron microscopy, and thermodynamic analyses showed that the interface mainly contained intermetallic compound TiAl_3 and Al matrix. The joints featured good mechanical properties, i.e., shear strength of 154 MPa, tensile strength of 215 MPa, and compressive strength of 283 MPa, which are superior to those of joints fabricated by other methods. Coherent boundaries between Al/TiAl_3 and TiAl_3/Ti were confirmed to contribute to outstanding interfacial mechanical properties and also explained constant fracture occurrence in the Al matrix. Follow-up studies should focus on improving mechanical properties of the Al matrix by deformation and heat treatment.

The Simulation and Optimization of Aspheric Plastic Lens Injection Molding

For the purpose of reducing the volumetric shrinkage and volumetric shrinkage variation, the process in injection molding of aspheric plastic lens was simulated, and several process parameters which include holding pressure, melt temperature, mold temperature, fill time, holding pressure time and cooling time were optimized by using an orthogonal experimental design method. Finally, the optimum process parameters and the influence degree of process parameters on the average volumetric shrinkage and the volumetric shrinkage variation are obtained.

Preparation of Ti-Mo getters by injection molding

Ti-Mo getters have been fabricated via metal injection molding (MIM) using three kinds of Ti powders with different mean particle sizes of 46 μm,35 μm and 26 μm,respectively. The surface morphology,porosity,and hydrogen sorption properties of Ti-Mo getters formed by MIM using paraffin wax as a principal binder constituent were examined. It has been proven that the powder injection molding is a viable forming technique for porous Ti-Mo getters. The particle size of Ti powders and the powder loading influence the porosity of getters,and this affects the sorption capacity of Ti-Mo getters. Ti-Mo getters produced with the Ti powders possessing a mean particle size of 35 μm using a powder loading of 40 vol.% have a high porosity,resulting in a good sorption capacity.

Fabrication of micro gear wheels by micropowder injection molding

The micropowder injection molding technology was investigated to fabricate the microsized gear wheels on a conventional injection molding machine. The feedstock comprised of carbonyl ferrum powder and a wax-based thermoplastic binder. Microinjection molding was fulfilled at about 423 K under 100 MPa. The heating system was applied to the die to improve the fluidity of the feedstock and subsequently the cooling system was used to enhance the strength of the green compacts after injection by decreasing the temperature of the die. The gear wheels were realized successfully with their addendum circle diameter ranging from 800 to 200 um and with the center hole as small as 60 um.

Mold Filling Analysis in Vacuum Infusion Molding Process Based on a High-Permeable Medium

The objective of this paper is to understand the flow mechanism through visualization experiments and discuss theinfluence of process parameters on mold filling process. A 2D leakage flow model is developed to simulate the moldingprocess, and the simulation results show good agreement with experiments.

RHEOLOGICAL PROPERTIES OF METAL INVECTION MOLDING BINDER AND FEEDSTOCK

ＲＨＥＯＬＯＧＩＣＡＬＰＲＯＰＥＲＴＩＥＳＯＦＭＥＴＡＬＩＮＶＥＣＴＩＯＮＭＯＬＤＩＮＧＢＩＮＤＥＲＡＮＤＦＥＥＤＳＴＯＣＫ①ＬｉＹｉｍｉｎ，ＱｕＸｕａｎｈｕｉ，ＨｕａｎｇＢａｉｙｕｎ，ＱｉｕＧｕａｎｇｈａｎＮａｔｉｏｎａｌＫｅｙＬａｂｏｒａｔｏｒｙ...