A Study of Fabrication Technique, Structural and Morphological Behavior of Polypropylene Reinforced with Short Natural Fiber Banana

Fiber reinforced polypropylene has been widely accepted as material for structural and engineering applications in recent years.Jute,Banana fibers etc.are the most common low cost,versatile,renewable and abundantly available natural fibers which have biodegradable properties.All these fibers are versatile,renewable and most common agro based fibers that have enormous aspect due to their potentiality in composite manufacture.In comparison to other artificial fibers there are many advantages of natural fibers due to everyday applications such as,paperweight,suitcases,lampshades,helmets,and shower and bath units.Untreated and alkali treated banana fiber reinforced with Polypropylene matrix composite were fabricated with 10-25%loading of fiber by weight and were fabricated as Polypropylene Banana Composite(PPBC).Using melt mixing hot press molding technique these biodegradable composites were prepared.Different characteristics like morphologies and micro structural analysis of the composites were studied by Scanning electron microscope(SEM)and infrared spectroscopy instrument(IR).Due to the concept of group vibration infrared spectroscopy has the extensive application.Any kind of structural change such as addition or substitution of groups or atoms in a molecule may affect the relative mode of vibration of the group.This causes change in IR spectral band position,change in relative intensities and appearance of new bands and disappearance of any band and splitting of a single band into two or more bands.To increase the utility of fiber infrared spectroscopy can also be used.It deals with the interaction of infrared light with matter.The former can indicate the presence of functional groups qualitatively and the latter can provide a semi quantitative measure of their concentrations.On the other hand Electron Microscopy is most widely used to obtain information regarding the morphology of fiber surfaces,especially SEM(Scanning Electron Microscopy).Using SEM,it is easy to determine the differences of fiber surface topography after and before treatment,and hence the formation of fiber polymer composites.Fiber deboning was also observed for untreated and treated fiber pp matrix composite.The SEM can have a magnification range from a few times to several hundred thousand times.

Fabrication and Characterization on Physico-Mechanical and Structural Properties of Sawdust Reinforced Acrylonitrile Butadiene Styrene (ABS) Composites

The sawdust reinforced Acrylonitrile Butadiene Styrene (ABS) composites were prepared by using hot press molding machine for five different wt% (0%, 5%, 10%, 15% and 20%) at 180°C temperature and 50 KN load. Sawdust was collected from local saw mill of Savar, Dhaka, Bangladesh and ABS polymer was collected from local market of Dhaka, Bangladesh. In this study, different properties of composites like physical (bulk density and water absorption), mechanical (tensile properties and hardness) and structural (Fourier Transform Infrared Spectroscopy) properties were studied. The bulk density of composites was not altered consistently and it gave greater value for 5% and 20% composites. The water absorption enhanced for all composites with the accumulation of fiber content and soaking time. The reduction of tensile strength and Leeb’s rebound hardness of the composites were observed with the increase of the fiber content in all compositions. Maximum (%) of elongation was found for 5% composite, and then it gradually decreased;however, elastic modulus increased with the increased of fiber content in composites. Fourier Transform Infrared (FTIR) spectroscopy study was done for structural characterization. It was found that there was a new bond (C≡C) stretching formed for 20% composite;moreover, C-H rocking for 0% composite was broken for all other composites after the addition of sawdust in ABS polymer matrix.

Preparation and characterization of bioactive glass tablets and evaluation of bioactivity and cytotoxicity in vitro

In this study, the SiO2eCaOeP2O5 ternary component of bioactive glass particles were successfullysynthesized by sol-gel method, then the bioactive glass particles were pressed into tablets with drypressing molding technology. The physicochemical structure, in-vitro bioactivity and biocompatibility ofBG tablets were characterized by various methods, such as XRD、SEM、FTIR, etc. The results showedthat the sol-gel bioactive glass particle was distinguished with its amorphous structure and micron-size.After being soaked in Tris-Hcl solution for 15 d, the bioactive glass tablets didn't collapse. Also, themineralization assay in vitro showed that the bioactive glass tablets had good capability of inducing theformation of hydroxycarbonate apatite (HCA) after being immersed in simulated body fluid (SBF). Inaddition, the cytotoxicity assay indicated that the osteoblast (MC3T3) grew well on the surface ofbioactive glass tablets. According to the above results, the bioactive glass tablets presented good mechanicalstrength, excellent apatite-forming activity and high biocompatibility, which demonstratedtheir potential applications in the field of bone defect repairing.

Microstructure and mechanical property of MIM 418 superalloy

In this study, the influence of hot isostatic pressing（HIP） process on the 418 alloy produced by metal injection molding（MIM） technique（named as MIM 418）was investigated based on the characteristic analysis of 418 alloy powder. And comparison analysis of the microstructure and mechanical property between the MIM 418 and as-cast 418 alloys was performed by scanning electron microscopy（SEM）, energy-dispersive spectroscopy（EDS）,and X-ray diffraction（XRD）. The results show that MIM418 alloy exhibits fine grain（~30 μm） and uniform microstructure. The defects existing in MIM 418 alloy formed during sintering process can be eliminated through HIP treatment, and the relative density increases from97.0 % to 99.5 %. The mechanical property can be improved significantly because of the elimination of defects, and the tensile strength and elongation are1,271 MPa and 16.8 %, respectively, which are increased by 34.5 % and 180 % compared with K418 alloy after solution heat treatment.