Experimental studies on the rheological properties of a Ca O–Si O2–Al2O3–Mg O–Ti O2–(Ti C) blast furnace(BF) slag system were conducted using a high-temperature rheometer to reveal the non-Newtonian behavior of h...Experimental studies on the rheological properties of a Ca O–Si O2–Al2O3–Mg O–Ti O2–(Ti C) blast furnace(BF) slag system were conducted using a high-temperature rheometer to reveal the non-Newtonian behavior of heterogeneous titanium-bearing molten slag. By measuring the relationships among the viscosity, the shear stress and the shear rate of molten slags with different Ti C contents at different temperatures, the rheological constitutive equations were established along with the rheological parameters; in addition, the non-Newtonian fluid types of the molten slags were determined. The results indicated that, with increasing Ti C content, the viscosity of the molten slag tended to increase. If the Ti C content was less than 2wt%, the molten slag exhibited the Newtonian fluid behavior when the temperature was higher than the critical viscosity temperature of the molten slag. In contrast, the molten slag exhibited the non-Newtonian pseudoplastic fluid characteristic and the shear thinning behavior when the temperature was less than the critical viscosity temperature. However, if the Ti C content exceeded 4wt%, the molten slag produced the yield stress and exhibited the Bingham and plastic pseudoplastic fluid behaviors when the temperature was higher and lower than the critical viscosity temperature, respectively. When the Ti C content increased further, the yield stress of the molten slag increased and the shear thinning phenomenon became more obvious.展开更多
The use of iron ores bearing titanium as a raw material is an effective measure to prevent hearth erosion and prolong the life of a blast furnace. In this research, the effect of titanium content on the precipitation ...The use of iron ores bearing titanium as a raw material is an effective measure to prevent hearth erosion and prolong the life of a blast furnace. In this research, the effect of titanium content on the precipitation behaviors of high-melting phases of carbon-saturated molten pig iron were studied by confocal scanning laser microscopy. The results showed that, when the titanium content was less than 0.25 wt%,Fe_3C was precipitated as a single phase from the molten carbon-saturated iron. The growth rate of the precipitated Fe_3C crystals was very high, reaching 7387 μm^2/s. When the titanium content in the molten pig iron was greater than 0.47 wt%, TiC crystals precipitated first. The shape and size of the precipitated TiC crystals did not obviously change. After TiC was precipitated, the fluidity of the molten pig iron worsened. With a decrease in temperature, Fe_3C was also precipitated but the growth rate of Fe_3C was limited by the presence of the first precipitated TiC phase. The crystal size of the precipitated Fe_3C was much smaller than that of pure Fe_3C.展开更多
为研究冷金属过渡(cold metal transition,CMT)电弧增材制造铝合金传热传质与熔池流动特性,基于Fluent软件建立了三维CMT电弧增材制造数值模型.模型中,采用动网格技术模拟焊丝竖直方向上的往复运动,利用流体体积法捕获气/液界面,焓-孔...为研究冷金属过渡(cold metal transition,CMT)电弧增材制造铝合金传热传质与熔池流动特性,基于Fluent软件建立了三维CMT电弧增材制造数值模型.模型中,采用动网格技术模拟焊丝竖直方向上的往复运动,利用流体体积法捕获气/液界面,焓-孔隙率法追踪固/液界面,并施加周期热量输入和阶段电弧力作用来等效电弧放电行为,研究分析了焊道成形传热传质过程与熔池动态行为.结果表明,焊道成形初期,熔池余高和坡度较大,形貌犹如半个球体,成形后期热量积累造成焊道余高后方较前方略小,而后端熔宽较前端略宽;单滴过渡周期内,焊丝机械回抽对熔池表面流动影响最为明显,液桥断裂产生较大反冲作用于熔池;熔池内部则是电磁力作为主导驱动力产生一股顺时针环流,环流随燃弧阶段周期切换而不断加强与减弱,并基本贯穿整个过渡周期,使得熔池内部热对流更加充分.模拟结果与试验结果显示吻合良好.展开更多
熔池金属流动一方面受电弧行为影响,另一方面与凝固组织形核、结晶过程联系紧密,是电弧焊接基础研究的关键,针对电弧力作用研究了超高频脉冲电弧焊接(UHFPAW,Ultra High Frequency Pulsed Arc Welding)熔池金属流动特点,采用理论研究与...熔池金属流动一方面受电弧行为影响,另一方面与凝固组织形核、结晶过程联系紧密,是电弧焊接基础研究的关键,针对电弧力作用研究了超高频脉冲电弧焊接(UHFPAW,Ultra High Frequency Pulsed Arc Welding)熔池金属流动特点,采用理论研究与试验分析相结合的方式对熔池流动方式、强度、温度分布等要素进行了分析,并完成了液态金属表面运动特征监测.结果表明,超高频脉冲电弧对熔池液态金属的热、力作用显著,表面流体流速大于30 cm/s,UHFP-AW电弧力造成熔池表面沉降变形,引起双环流,熔池温度扩散范围相应减小,有效降低了电弧热量对母材金属的影响,尤其在钛合金焊接中对控制焊缝晶粒尺寸具有重要意义.展开更多
基金financially supported by the National Science Foundation of China (Nos. 51090383 and 51174051)
文摘Experimental studies on the rheological properties of a Ca O–Si O2–Al2O3–Mg O–Ti O2–(Ti C) blast furnace(BF) slag system were conducted using a high-temperature rheometer to reveal the non-Newtonian behavior of heterogeneous titanium-bearing molten slag. By measuring the relationships among the viscosity, the shear stress and the shear rate of molten slags with different Ti C contents at different temperatures, the rheological constitutive equations were established along with the rheological parameters; in addition, the non-Newtonian fluid types of the molten slags were determined. The results indicated that, with increasing Ti C content, the viscosity of the molten slag tended to increase. If the Ti C content was less than 2wt%, the molten slag exhibited the Newtonian fluid behavior when the temperature was higher than the critical viscosity temperature of the molten slag. In contrast, the molten slag exhibited the non-Newtonian pseudoplastic fluid characteristic and the shear thinning behavior when the temperature was less than the critical viscosity temperature. However, if the Ti C content exceeded 4wt%, the molten slag produced the yield stress and exhibited the Bingham and plastic pseudoplastic fluid behaviors when the temperature was higher and lower than the critical viscosity temperature, respectively. When the Ti C content increased further, the yield stress of the molten slag increased and the shear thinning phenomenon became more obvious.
基金financially supported by the National Natural Science Foundation of China (No. 51674054)the Open Foundation of State Key Laboratory of Vanadium and Titanium Resources Comprehensive Utilization of China
文摘The use of iron ores bearing titanium as a raw material is an effective measure to prevent hearth erosion and prolong the life of a blast furnace. In this research, the effect of titanium content on the precipitation behaviors of high-melting phases of carbon-saturated molten pig iron were studied by confocal scanning laser microscopy. The results showed that, when the titanium content was less than 0.25 wt%,Fe_3C was precipitated as a single phase from the molten carbon-saturated iron. The growth rate of the precipitated Fe_3C crystals was very high, reaching 7387 μm^2/s. When the titanium content in the molten pig iron was greater than 0.47 wt%, TiC crystals precipitated first. The shape and size of the precipitated TiC crystals did not obviously change. After TiC was precipitated, the fluidity of the molten pig iron worsened. With a decrease in temperature, Fe_3C was also precipitated but the growth rate of Fe_3C was limited by the presence of the first precipitated TiC phase. The crystal size of the precipitated Fe_3C was much smaller than that of pure Fe_3C.
文摘为研究冷金属过渡(cold metal transition,CMT)电弧增材制造铝合金传热传质与熔池流动特性,基于Fluent软件建立了三维CMT电弧增材制造数值模型.模型中,采用动网格技术模拟焊丝竖直方向上的往复运动,利用流体体积法捕获气/液界面,焓-孔隙率法追踪固/液界面,并施加周期热量输入和阶段电弧力作用来等效电弧放电行为,研究分析了焊道成形传热传质过程与熔池动态行为.结果表明,焊道成形初期,熔池余高和坡度较大,形貌犹如半个球体,成形后期热量积累造成焊道余高后方较前方略小,而后端熔宽较前端略宽;单滴过渡周期内,焊丝机械回抽对熔池表面流动影响最为明显,液桥断裂产生较大反冲作用于熔池;熔池内部则是电磁力作为主导驱动力产生一股顺时针环流,环流随燃弧阶段周期切换而不断加强与减弱,并基本贯穿整个过渡周期,使得熔池内部热对流更加充分.模拟结果与试验结果显示吻合良好.
文摘熔池金属流动一方面受电弧行为影响,另一方面与凝固组织形核、结晶过程联系紧密,是电弧焊接基础研究的关键,针对电弧力作用研究了超高频脉冲电弧焊接(UHFPAW,Ultra High Frequency Pulsed Arc Welding)熔池金属流动特点,采用理论研究与试验分析相结合的方式对熔池流动方式、强度、温度分布等要素进行了分析,并完成了液态金属表面运动特征监测.结果表明,超高频脉冲电弧对熔池液态金属的热、力作用显著,表面流体流速大于30 cm/s,UHFP-AW电弧力造成熔池表面沉降变形,引起双环流,熔池温度扩散范围相应减小,有效降低了电弧热量对母材金属的影响,尤其在钛合金焊接中对控制焊缝晶粒尺寸具有重要意义.
基金supported by the National Natural Science Foundation of China (21271054, 21173060)Major Research Plan of the National Natural Science Foundation of China (91326113, 91226201)Fundamental Research Funds for the Central Universities, China (HEUCF201403001)~~
