Formation and spectroscopic characterization of mono-dispersed CdSe nanocrystals

In this article, mono-dispersed hexagonal structure CdSe nanocrystals with polyhedron shape were prepared by an open solvent thermal reaction. They show a discrete excitonic transition structure in the absorption spectra and the minimal photoluminescence （PL） peak full-width at half-maximum of 19nm. The PL quantum yield is about 60%. Transmission electron micrographs, high-resolution transmission electron micrographs, x-ray powder diffraction patterns, UV-vis absorption spectra and PL spectra were obtained for the as-prepared CdSe nanocrystals. The size of the CdSe nanocrystals can be tuned by changing the reaction temperature or time. Due to the improved synthesis method, a different growth mechanism of the CdSe nanocrystals is discussed.

Simulation on dissolute and dust dispersion in comprehensive mechanized heading face with forced-exhaust ventilation

According to the characteristics of comprehensive mechanized heading face, established the mathematical model of single-phase air flow with κ-ε two equations model, and have established κ-ε-θ-κp mathematic model to solve two-phase flow of gas and particles in dust space with eulerian-eulerian method and eulerian-lagrangian method. Numerical solution of gas-particle two-phase flow was put forward based on collocated grid SIMPLE algorithm. Moreover, numerical simulation of dust concentration in fully mechanized caving face was carded out by using Fluent software. Finally, when in forced-exhaust ventilation circumstance, drawer type fan drum have less dust absorption, and most of dust spread to the other site; the dust concentration is inversely proportional to the distance from tunneling head, and the dust concentration has already diffused to decrease below 102 mg/m3 at the position ofx=12 m. Dust are more focused on relative side（in the range about y from 0 to 2 meter） of roadway space of press-ventilated fan drum, especially between tunneling place and drawer type fan drum; the roadway with road header have a higher dust concentration. These conclusions provide reliable theory basis for the dust prevention in comprehensive mechanized heading face.

La(Ⅲ) Transport in Dispersion Supported Liquid Membrane Including PC-88A as the Carrier and HCl Solution as the Stripping Solution

The transport of La(III) through a dispersion supported liquid membrane with polyvinylidene fluoride membrane as the liquid membrane support and dispersion solution including HCl solution as the stripping solution and 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (PC-88A) in kerosene as the membrane solution, was studied. As a result, the optimum transport conditions of La(Ⅲ) were obtained as that concentration of HCl solution was 4.0 mol/L, concentration of PC-88A 0.16 mol/L, and volume ratio of membrane to stripping solution 30:30 in the dispersion phase, and pH value 4.0 in the feed phase. Ionic strength had no obvious effect on the transport of La(Ⅲ). Under the optimum conditions, when initial concentration of La(Ⅲ) was 0.8×10-4 mol/L, the transport rate was up to 96.3% during the transport time of 125 min. The kinetic equation was developed based on the law of mass diffusion and theory of interface chemistry. The diffusion coefficient of La(Ⅲ) in the membrane and the thickness of diffusion layer between feed and membrane phases were obtained as 3.20×10-7 m2/s and 3.22×10-5 m, respectively. The calculated results were in good agreement with experimental results.

Matrix Solid-phase Dispersion Extraction of Alkaloids from the Roots of Aconitum kusnezoffii Reichb

Matrix solid-phase dispersion（MSPD） was developed for the extraction of four alkaloids, including aconitine, mesaconitine, hypaconitine and deoxyaconitine, from the roots ofAconitum kusnezoffii Reichb. The determination of the analyte was carried out by high performance liquid chromatography with UV detection. The alkaline alumina was used as sorbent. The mixture of acetonitrile and water was used as elution solvent. Several extraction parameters, such as type of sorbent, the ratio of sample to solid support material, type of the elution solvent and the volume of the elution solvent were tested. Mean recoveries ranged from 93.16% to 102.73%, with relative standard deviations from 0.27% to 4.17%. With the extraction efficiency and time expenditure taken into account, MSPD extraction should be a comparatively good method.

Stable CuO/La_(2)Sn_(2)O_(7) catalysts for soot combustion:Study on the monolayer dispersion behavior of CuO over a La_(2)Sn_(2)O_(7) pyrochlore support

To understand the dispersion behavior of metal oxides on composite oxide supports and with the expectation of developing more feasible catalysts for soot oxidation,CuO/La_(2)Sn_(2)O_(7)samples containing varied CuO loadings were fabricated and characterized by different techniques and density functional theory calculations.In these catalysts,a spontaneous dispersion of CuO on the La_(2)Sn_(2)O_(7)pyrochlore support formed,having a monolayer dispersion capacity of 1.90 mmol CuO/100 m^(2) La_(2)Sn_(2)O_(7)surface.When loaded below this capacity,CuO exists in a sub-monolayer or monolayer state.X-ray photoelectron spectroscopy(XPS),Raman spectroscopy,and Bader charge and density of states analyses indicate that there are strong interactions between the sub-monolayer/monolayer CuO and the La_(2)Sn_(2)O_(7)support,mainly through the donation of electrons from Cu to Sn at the B-sites of the structure.In contrast,Cu has negligible interactions with La at the A-sites.This suggests that,in composite oxide supports containing multiple metals,the supported metal oxide interacts preferentially with one kind of metal cation in the support.The Raman,in situ diffuse reflectance infrared Fourier transform spectroscopy,and XPS results confirmed the formation of both O2^(-)and O2^(2-)as the active sites on the surfaces of the CuO/La_(2)Sn_(2)O_(7)catalysts,and the concentration of these active species determines the soot combustion activity.The number of active oxygen anions increased with increase in CuO loading until the monolayer dispersion capacity was reached.Above the monolayer dispersion capacity,microsized CuO crystallites formed,and these had a negative effect on the generation of active surface oxygen sites.In summary,a highly active catalyst can be prepared by covering the surface of the La_(2)Sn_(2)O_(7)support with a CuO monolayer.

THE EXTRACTED COMPLEX FORMED BY MONO (2-ETHYLHEXYL)-2-ETHYLHEXYL PHOSPHATE WITH DIVALENT Mn

In order to clarify the mechanism and the complex formed in the extraction of divalent Mn by alkylphosphonic acid monoester, the solid complex has been prepared by mono (2-ethylhexyl)-2-ethylhexyl phosphate, HEH(EH)P, HA with divalent Mn. The elemental analysis, magnetic susceptibility and thermogravimetry have been determined for the solid complex of HEH(EH)P-Mn(II) and the infrared spectrum has been carried out in comparison to the extractant HEH(EH)P. The extracted compound has also been studied by electronic and electron spin resonance spectroscopy in octane solvent and solid state at room temperature. On the basis of the measurements, it is concluded that the structure of the solid polymeric species MnA_2 is in a tetrahedral arrangement.

SiO_2/稀土Eu(Ⅲ)配合物核-壳复合粒子的制备及发光性能研究

采用Stober法制备了粒径为40-60nm的单分散纳米SiO2微球，以氧化铕为原料、α-噻吩甲酰三氟丙酮和邻菲哆啉为配体制备了稀土铕的三元配合物，并将其成功包覆在SiO2微球表面，形成核-壳复合粒子。采用红外光谱和元素分析表征配合物的结构。透射电镜照片表明，稀土有机配合物在SiO2微球表面形成了致密的纳米级包覆层，包覆层厚度随配合物用量的增加而增加。复合粒子呈现出很强的Eu配合物发光，纳米SiO2核对配合物有荧光增强作用，但配合物浓度较高时荧光增强效应有所减弱。

正交设计在溶胶-凝胶法制备单分散球形SiO_2中的研究

通过正交试验设计,用L9(43)正交表安排实验,在醇氨反应体系中采用溶胶-凝胶(sol-gel)法制备单分散球形SiO2,运用直观图和极差分析确定各主要原料对制备不同粒径SiO2的影响,优化配比。研究表明:对单分散球形SiO2的平均粒径的影响次序为:用水量、醇用量、氨水和正硅酸乙酯(TEOS)用量。通过控制反应条件,可实现在一定范围内获得尺寸均一、不同粒径、分散性好的球形SiO2。制备出的单分散球形SiO2颗粒形态完整,粒径140～500nm,分布窄、单分散性好。

无皂乳液聚合法制备P(St-MMA-SPMAP)单分散乳胶颗粒

利用无皂乳液聚合 ,分别用一步法和两步法合成了单分散的聚 (苯乙烯 甲基丙烯酸甲酯 甲基丙烯酸丙基磺酸钾 ) (P(St MMA SPMAP) )乳胶颗粒 .在该聚合体系中 ,当水溶性磺酸基单体SPMAP的浓度小于 17mmol L时 ,为均相成核过程 ,能制备单分散的乳胶颗粒 .其中 ,用两步法制备的乳胶颗粒相互之间无粘连 .此外 ,还对一步法合成苯乙烯 甲基丙烯酸甲酯 甲基丙烯酸辛基磺酸钠 (P(St MMA SOMAS) )乳胶颗粒进行了初步研究 .

1-氨基-2-(N,N-二甲氨基)-4-羟基-蒽醌的合成新方法

以分散红60和DMF为原料,在碳酸钾作用下反应制备得到1-氨基-2-(N,N-二甲氨基)-4-羟基-蒽醌,产品收率92.8%。

分散液液微萃取-气相色谱-质谱分析葡萄酒中单萜醇

采用分散液液微萃取与气相色谱-质谱（GC-MS）联用技术建立了葡萄酒中单萜醇（α-萜烯醇、芳樟醇、香叶醇、香茅醇）的分析方法。考察萃取剂与分散剂的种类和体积、超声和离心时间、盐的加入量、酒样中乙醇含量等因素对萃取效率的影响,确定最佳萃取条件为：在10 m L葡萄酒样中加入2,6-二叔丁基-4-甲基苯酚（BHT）作为内标,再加入100μL四氯化碳与500μL丙酮,超声3 min（40 MHz）,再离心10 min（5000 r/min）后吸取有机相进行GC-MS分析。用此条件检测4种单萜醇,线性范围为10-300μg/L,相关系数均大于0.996,检出限为6-8μg/L。实际葡萄酒样加标回收率为90.8%-96.1%,相对标准偏差为4.8%-5.6%（n=6）。本方法具有操作简单、快速、灵敏、低成本、环境友好等特点,非常适合大批量样品分析。

气相色谱-负化学源质谱联用法测定水产品及食用油中氟乐灵的残留量

建立了一种可用于水产品及食用油中氟乐灵残留量分析的分散型固相萃取-气相色谱-负化学离子源质谱方法。水产品及食用油经乙腈提取，4℃冷藏后，采用分散型固相萃取法净化，由气相色谱-负化学离子源质谱选择离子监测技术进行测定与确证，同位素内标法定量。在1～40μg / L 范围内氟乐灵农药的线性关系良好；方法定量限（LOQ）为0.02μg / kg；对鳗鱼、烤鳗、梭子蟹、小龙虾、猪油和橄榄油等6种复杂基质进行1.0、2.0和3.0μg / kg 等3个水平的添加回收试验，平均回收率均处于80％～100％之间，RSD≤10.3％；无干扰现象出现。该方法可作为水产品及食用油中氟乐灵残留检测的确证方法。

On the monolayer dispersion behavior of Co_(3)O_(4)on HZSM-5 support:designing applicable catalysts for selective catalytic reduction of nitrogen oxides by ammonia

Based on monolayer dispersion theory,Co_(3)O_(4)/ZSM-5 catalysts with different loadings have been prepared for selective catalytic reduction of nitrogen oxides by ammonia.Co_(3)O_(4)can spontaneously disperse on HZSM-5 support with a monolayer dispersion threshold of 0.061 mmol 100 m^(-2),equaling to a weight percentage around 4.5%.It has been revealed that the quantities of surface active oxygen(O_(2)^(-))and acid sites are crucial for the reaction,which can adsorb and activate NO_(x)and NH_(3)reactants effectively.Below the monolayer dispersion threshold,Co_(3)O_(4)is finely dispersed as sub-monolayers or monolayers and in an amorphous state,which is favorable to generate the two kinds of active sites,hence promoting the performance of ammonia selective catalytic reduction of nitrogen oxide.However,the formation of crystalline Co_(3)O_(4)above the capacity is harmful to the reaction performance.4%Co_(3)O_(4)/ZSM-5,the catalyst close to the monolayer dispersion capacity,possesses the most abundant active O_(2)^(-)species and acidic sites,thereby demonstrating the best reaction performance in all the samples.It is proposed the optimal Co_(3)O_(4)/ZSM-5 catalyst can be prepared by loading the capacity amount of Co_(3)O_(4)onto HZSM-5 support.

St-DVB交联微球的制备及其性能研究

制备了聚苯乙烯-二乙烯基苯交联微球,用扫描电镜、傅里叶变换红外光谱仪、激光粒度分析仪等对微球进行了表征,研究了溶胀剂、引发剂、苯乙烯-二乙烯基苯、加料顺序等反应条件对微球形貌的影响。结果表明,实验选用过氧化苯甲酰作为引发剂,质量分数为1.26%～6.12%;丙酮为溶胀剂,质量分数为2.65%～34.28%;制备的交联微球呈单分散性。

Symplectic analysis for elastic wave propagation in two-dimensional cellular structures

On the basis of the finite element analysis, the elastic wave propagation in cellular structures is investigated using the symplectic algorithm. The variation principle is first applied to obtain the dual variables and the wave propagation problem is then transformed into two-dimensional （2D） symplectic eigenvalue problems, where the extended Wittrick-Williams algorithm is used to ensure that no phase propagation eigenvalues are missed during computation. Three typical cellular structures, square, triangle and hexagon, are introduced to illustrate the unique feature of the symplectic algorithm in higher-frequency calculation, which is due to the conserved properties of the structure-preserving symplectic algorithm. On the basis of the dispersion relations and phase constant surface analysis, the band structure is shown to be insensitive to the material type at lower frequencies, however, much more related at higher frequencies. This paper also demonstrates how the boundary conditions adopted in the finite element modeling process and the structures＇ configurations affect the band structures. The hexagonal cells are demonstrated to be more efficient for sound insulation at higher frequencies, while the triangular cells are preferred at lower frequencies. No complete band gaps are observed for the square cells with fixed-end boundary conditions. The analysis of phase constant surfaces guides the design of 2D cellular structures where waves at certain frequencies do not propagate in specified directions. The findings from the present study will provide invaluable guidelines for the future application of cellular structures in sound insulation.

A novel type of transverse surface wave propagating in a layered structure consisting of a piezoelectric layer attached to an elastic half-space

The existence and propagation of transverse surface waves in piezoelectric coupled solids is investigated, in which perfect bonding between a metal/dielectric substrate and a piezoelectric layer of finite-thickness is assumed. Dis- persion equations relating phase velocity to material con- stants for the existence of various modes are obtained in a simple mathematical form for a piezoelectric material of class 6mm. It is discovered and proved by numerical examples in this paper that a novel Bleustein-Gulyaev （B-G） type of transverse surface wave can exist in such piezoelectric cou- pled solid media when the bulk-shear-wave velocity in the substrate is less than that in the piezoelectric layer but greater than the corresponding B-G wave velocity in the same pie- zoelectric material with an electroded surface. Such a wave does not exist in such layered structures in the absence of pie- zoelectricity. The mode shapes for displacement and electric potential in the piezoelectric layer are obtained and discussed theoretically. The study extends the regime of transverse sur- face waves and may lead to potential applications to surface acoustic wave devices.

Study on transport of Dy(Ⅲ) by dispersion supported liquid membrane

The transport of Dy（III） through a dispersion supported liquid membrane （DSLM） consisting of polyvinylidene fluoride membrane （PVDF） as the liquid membrane support and dispersion solution including HCI solution as the stripping solution and 2-ethyl hexyl phosphonic acid-mono-2-ethyl hexyl ester （PC-88A） dissolved in kerosene as the membrane solution, was studied. The effects of pH value, initial concentration of Dy（III） and different ionic strength in the feed phase, volume ratio of membrane solution and stripping solution, concentration of HCl solution, concentration of carrier, different stripping agents in the dispersion phase on transport of Dy（III） were also investigated, respectively. As a result, when the concentration of HCI solution was 4.0 mol/L, concentration of PC-88A was 0.10 mol/L, and volume ratio of membrane solution and stripping solution was 40：20 in the dispersion phase, and pH value was 5.0 in the feed phase, the transport effect of Dy（III） was the best. Ionic strength had no obvious effect on transport of Dy（III）. Under the optimum condition studied, when initial concentration of Dy（III） was 0.8×10^-4 mol/L, the transport rate of Dy（III） was up to 96.2% during the transport time of 95 rain. The kinetic equation was developed in terms of the law of mass diffusion and the theory of interface chemistry. The diffusion coefficient of Dy（III） in the membrane and the thickness of diffusion layer between feed phase and membrane phase were obtained and the values were 1.99×10^-7 m^2/s and 15.97 μm, respectively. The results were in good agreement with experimental results.

Compact Model for the Obnoxious <i>p</i>-Median Problem

Obnoxious facilities are those crucial to human living, yet antagonistic to the public or environment. However, the interactions between obnoxious facilities and their clients have been less frequently investigated. A state-of-the-art model for this problem involves numerous 0 - 1 variables, rendering it difficult to solve. This study aims at removing most of these 0 - 1 variables to enhanced model efficiency. A compact model is presented in this study, with the equivalence between the new and original models proved. Additionally, numerical tests were conducted to show that the proposed compact model is more efficient than the original one.

Fe3O4 NPs@MIL-53的直接自组装制备以及催化性能

通过直接自组装的方法制备了Fe3O4 NPs@MIL-53复合材料,并且通过PXRD,FTIR,TEM以及77 K下的N2吸附进行了表征。结果显示Fe3O4 NPs是被嵌入到MIL-53骨架结构中并被固定在晶格内部。Fe3O4NPs@MIL-53复合材料对苯乙烯催化环氧化有高的选择性。PRXD证明了Fe3O4 NPs@MIL-53复合材料的酸稳定性。

单分散性SiO_2的制备与应用

系统地介绍了单分散性二氧化硅的制备方法及其优缺点,列举了单分散性二氧化硅在有关方面的应用;最后在归纳前人研究成果的基础上,提出了超临界流体快速膨胀法制备单分散性二氧化硅的设想。