Altering the Hierarchical Morphology Distribution of Injection Molded Polyethylene by the Introduction of Crosslink Network and Periodical Shear

High density polyethylene （HDPE） with moderate content of crosslink network （CPE） was successfully prepared through chemical method. Specimens for structural characterization have been molded by conventional injection molding （CIM） and pressure vibration injection molding （PVIM）. Influence of crosslink network on hierarchical morphology distribution and mechanical properties was systematically studied. Polarized light microscopy （PLM） revealed that both CIM and PVIM PE samples have a typical ＂skin-core＂ structure and the thickness of shear layer of CIM PE and PVIM CPE samples obviously increase. Scanning electron microscopy （SEM） showed that shish-kebab structures are clearly observed in shear layer of CIM CPE sample, indicating that the crosslink network can surely improve the formation of shish-kebab structures. Moreover, we suppose that shish-kebab structures emerged in shear and core layer of PVIM CPE sample. Wide- angle X-ray diffraction （WAXD） and small-angle X-ray scattering （SAXS） confirmed that more orientation and shish-kebab structures form even in core layer of PVIM CPE sample, which demonstrated that the hierarchical morphology was apparently altered by periodical shear and crosslink network. Finally, the mechanical properties revealed that this oriented structure increase the tensile strength from 31 MPa of CIM PE sample to 46 MPa of PVIM CPE sample. However, the tensile behavior tended to change from ductile fracture to brittle fracture.

Relationships between femoral strength evaluated by nonlinear finite element analysis and BMD,material distribution and geometric morphology

Precisely quantifying the strength of the proximal femur and accurately assessing hip fracture risk would enable those at high risk to be identified so that preventive interventions could be taken.Development of better measures of femoral strength using the clinically

The Distribution and Morphological Diversity of GABA-containing Neurons in The Prefrontal Cortex of Human Newborn Baby Infant

The prefrontal cortex of a human full termnewborn infant just after accidental death was studies by mcans of immunocytochemical technique with antibody directedagainst GABA(Immunonuclear Corp.)and ABC kit(Vector)。GABA-containing neurons were found over all layers and all were nonpyramidal cells.The laminar distribution of GABA-containing ne-urons was not even between different layers,density in laye Ⅱ was prominently higher than any other layers,density in layer Ⅲ and layer Ⅳ was higher than that in layer V and Ⅵ.

GC-MS Analysis on Form and Content of Phytosterol in the Beans from Different Producing Areas

This paper established the GC-MS method to analyze phytosterol in beans and study the content and distribution of phytosterol in green beans,red beans,black beans and soybeans in 5 main producing areas of China(Inner Mongolia,Heilongjiang,Jilin,Hebei,Shandong).This paper used GC-MS method to analyze the content and distribution of campesterol,stigmasterol,sitostanol,brassicasterol,ergosterol,cycloartanol,cycloartenol,2,4-methylenecycloartanol,spinasterol,cholesterol and cholestanol in the beans from different producing areas.Results showed that the content of sterol in green beans was higher than in three other kinds of beans,and the content of sterol in red beans was the lowest.Different producing areas had a significant impact on the content of sterol in beans,and the dominant producing areas included Inner Mongolia and Heilongjiang.The study provided a basis for quality assessment and nutritional evaluation of beans and provided a reference for traceability and variety distinction study of other edible beans.

Mercury Speciation of Flue Gas Desulphurization By-Products in Coal-Fired Power Plants in China

The aim of this study was to develop and examine the morphology and distribution of mercury (Hg) in flue gas desulfurization (FGD) by-product. Mercury in the coal of coal-fired power plants is concentrated in the by-products of desulfurization process, and it is widely used as an additive in cement, building materials and other industries. Due to the different stability of various forms of mercury in the environment, subsequent use of products containing desulfurization by-product additives will continue to be released into the environment, endangering human health. Therefore, it is very necessary to study the form and distribution of mercury in the by-products of desulfurization in coal-fired power plants to provide a theoretical basis for subsequent harmless treatment. For content and morphology of mercury analysis, 1 sample of dry FGD ash and 6 samples of wet FGD gypsum were analyzed. The total 7 samples were extracted using a modification of sequential chemical extractions (SCE) method, which was employed for the partitioning Hg into four fractions: water soluble, acid soluble, H2O2 soluble, and residual. The Hg analysis was done with United States Environmental Protection Agency (USEPA) method 7471B. Comparing with the wet FGD gypsums of coal-fired boilers, the total Hg content in the dry FGD by-product was as high as 1.22 mg/kg, while the total Hg content in the FGD gypsum is 0.23 - 0.74 mg/kg, which was 2 times over the wet FGD gypsum. The concentration of water soluble Hg in the dry FGD by-product was the highest amount (0.72 mg/kg), accounting for 59.02% of the total mercury. While residual Hg content was 0.16 mg/kg, only about 13.11% of the total mercury. Mercury content in FGD gypsum was expressed in the form of ρ (residual Hg) > ρ (H2O2 soluble Hg) > ρ (water soluble Hg) > ρ (acid soluble Hg). The morphology and distribution of mercury in FGD by-products is supposed to be analyzed before utilization, and the impact of mercury on the environment should be considered.

Measurement, modelling, and closed-loop control of crystal shape distribution： Literature review and future perspectives

Crystal morphology is known to be of great importance to the end-use properties of crystal products, and to affect down-stream processing such as filtration and drying. However, it has been previously regarded as too challenging to achieve automatic closed-loop control. Previous work has focused on controlling the crystal size distribution, where the size of a crystal is often defined as the diameter of a sphere that has the same volume as the crystal. This paper reviews the new advances in morphological population balance models for modelling and simulating the crystal shape distribution （CShD）, measuring and estimating crystal facet growth kinetics, and two- and three-dimensional imaging for on-line characterisation of the crystal morphology and CShD. A framework is presented that integrates the various components to achieve the ultimate objective of model-based closed-loop control of the CShD. The knowledge gaps and challenges that require further research are also identified.

Size and elemental composition of dry-deposited particles during a severe dust storm at a coastal site of Eastern China

Dry-deposited particles were collected during the passage of an extremely strong dust storm in March, 2010 at a coastal site in Qingdao（36.15°N, 120.49°E）, a city located in Eastern China. The size, morphology, and elemental composition of the particles were quantified with a scanning electron microscope equipped with an energy dispersive X-ray instrument（SEM–EDX）. The particles appeared in various shapes, and their size mainly varied from 0.4to 10 μm, with the mean diameters of 0.5, 1.5, and 1.0 μm before, during, and after the dust storm, respectively. The critical size of the mineral particles settling on the surface in the current case was about 0.3–0.4 μm before the dust storm and about 0.5–0.7 μm during the dust storm. Particles that appeared in high concentration but were smaller than the critical size deposited onto the surface at a small number flux. The elements Al, Si and Mg were frequently detected in all samples, indicating the dominance of mineral particles. The frequency of Al in particles collected before the dust storm was significantly lower than for those collected during and after the dust storm. The frequencies of Cl and Fe did not show obvious changes, while those of S, K and Ca decreased after the dust arrival. These results indicate that the dust particles deposited onto the surface were less influenced by anthropogenic pollutants in terms of particle number.