ABS is an active safety system which showed a valuable contribution to vehicle safety and stability since it was first introduced. Recently, EVs with in-wheel-motors have drawn increasing attention owing to their grea...ABS is an active safety system which showed a valuable contribution to vehicle safety and stability since it was first introduced. Recently, EVs with in-wheel-motors have drawn increasing attention owing to their greatest advantages. Wheels torques are precisely and swiftly controlled thanks to electric motors and their advanced driving techniques. In this paper, a regenerative-ABS control RABS is proposed for all-in-wheel-motors-drive EVs. The RABS is realized as a pure electronic braking system called brake-by-wire. A coordination strategy is suggested to control RABS compromising three layers. First, wheels slip control takes place, and braking torque is calculated in the higher layer. In the coordinate interlayer, torque is allocated between actuators ensuring maximal energy recovery and vehicle stability. While in the lower layer, actuator control is performed. The RABS effectiveness is validated on a 3-DOF EVSimulink model through two straight-line braking manoeuvres with low and high initial speeds of 50 km/h and 150 km/h, respectively. Both regular and emergency braking manoeuvres are considered with ABS enabled and disabled for comparison. Simulation results showed the high performance of the proposed RABS control in terms of vehicle stability, brake response, stopping distance, and battery re-charging.展开更多
A vehicle stopping method using an electric brake until a traction motor is stopped is studied. At the moment of vehicle stop, electric brake is changed to control mode where torque is reduced at a low speed. Gradient...A vehicle stopping method using an electric brake until a traction motor is stopped is studied. At the moment of vehicle stop, electric brake is changed to control mode where torque is reduced at a low speed. Gradient is controlled by estimating the load torque of motor, thereby traction motor is not rotated after stop. In addition, coasting operation and brake test are performed from normal-opposite operation and start using a small-scale model comprising the inertial load equipment and the power converter. Further, traction motor is made to be equipped with a suspension torque. Pure electric braking that makes traction motor stop by an air brake at the time of stop is also implemented. Constant torque range and constant power range are expanded during braking so that braking force is secured with the electric brakes even in high speed region. Therefore, vehicle reduction effect can be expected by reducing parts related with an air brake which is not used frequently by using a pure electric brake in the M car in wide speed region. Further, maintenance of brake system can be reduced. Besides, ride comfort of passenger in the electric rail car, energy efficiency improvement, and noise reduction effect can be additionally expected. Further, an improved brake method that uses only an electric brake till motor stop is proposed by comparing those in the blending brake that uses an air brake while reducing brake torque at vehicle stop.展开更多
This paper describes in detail three kinds of typical compound braking strategy of wheel motor drive electric vehicle and summarizes the current commonly used strategies based on the three typical strategies developed...This paper describes in detail three kinds of typical compound braking strategy of wheel motor drive electric vehicle and summarizes the current commonly used strategies based on the three typical strategies developed. In the end, a new compound braking strategy is proposed;that is, we take braking mode classify, ECE regulations and SOC value of the battery as an important reference of braking force that joins the motor braking force, as well as we join the different identification models;according to the different braking modes, the purpose is that we can apply the different braking program.展开更多
Rising concern in environmental issues on global scale has made energy saving in powered equipment a very important subject.In order to improve the energy efficiency and driving range of a motor hoist,a regenerative b...Rising concern in environmental issues on global scale has made energy saving in powered equipment a very important subject.In order to improve the energy efficiency and driving range of a motor hoist,a regenerative braking system is designed and discussed.The system takes a unique ultracapacitor-only approach to energy storage system.The bi-directional bride DC？DC converter which regulates current flow to and from the ultracapacitor operates in two modes：boost and buck,depending on the direction of the flow.In order to provide constant input and output current at the ultracapacitor,this system uses a double proportional-integral（PI） control strategy in regulating the duty cycle of PWM to the DC？DC converter.The permanent magnet synchronous motor（PWSM） drive system is also studied.The space vector pulse width modulation（SVPWM） technique,along with a two-closed-loop vector control model,is adopted after detailed analysis of PMSM characteristics.The overall model and control strategy for this regenerative braking system is ultimately built and simulated under the MATLAB and Simulink environment.A test platform is built to obtain experimental results.Analysis of the results reveals that more than half of the gravitational potential energy can be recovered by this system.Simulation and experimentation results testify the validity of the double PI control strategy for interface circuit of ultracapacitor and SVPWM strategy for PMSM.展开更多
选择了配备有P1和P3的双电机插电式混合动力汽车(plug-in hybrid electric vehicle,PHEV)作为研究平台。在能量回收过程中,P1和P3电机可以同时进行,相比其他构型而言有着更加明显的能量回收优势。车辆制动过程中,当P1电机效率高于P3时,...选择了配备有P1和P3的双电机插电式混合动力汽车(plug-in hybrid electric vehicle,PHEV)作为研究平台。在能量回收过程中,P1和P3电机可以同时进行,相比其他构型而言有着更加明显的能量回收优势。车辆制动过程中,当P1电机效率高于P3时,优先选用P1电机进行制动,P3电机提供剩余所需制动力;当P3电机效率高于或等于P1时,则优先选用P3电机进行制动,P1电机弥补剩余所需的制动力。以搭载AMT(电控机械制动变速箱)的双电机插电式混合动力汽车为研究对象,在保证制动安全性的前提下,为尽可能地回收能量,提出一种基于双电机能量回收的前后轴制动力分配、机电制动力分配以及双电机制动力分配的多级制动力分配策略。结合Matlab/Simulink搭建整车模型,并进行仿真分析。仿真结果显示,制动能量回收率最高能达到66.56%,回收效果良好。展开更多
文摘ABS is an active safety system which showed a valuable contribution to vehicle safety and stability since it was first introduced. Recently, EVs with in-wheel-motors have drawn increasing attention owing to their greatest advantages. Wheels torques are precisely and swiftly controlled thanks to electric motors and their advanced driving techniques. In this paper, a regenerative-ABS control RABS is proposed for all-in-wheel-motors-drive EVs. The RABS is realized as a pure electronic braking system called brake-by-wire. A coordination strategy is suggested to control RABS compromising three layers. First, wheels slip control takes place, and braking torque is calculated in the higher layer. In the coordinate interlayer, torque is allocated between actuators ensuring maximal energy recovery and vehicle stability. While in the lower layer, actuator control is performed. The RABS effectiveness is validated on a 3-DOF EVSimulink model through two straight-line braking manoeuvres with low and high initial speeds of 50 km/h and 150 km/h, respectively. Both regular and emergency braking manoeuvres are considered with ABS enabled and disabled for comparison. Simulation results showed the high performance of the proposed RABS control in terms of vehicle stability, brake response, stopping distance, and battery re-charging.
文摘A vehicle stopping method using an electric brake until a traction motor is stopped is studied. At the moment of vehicle stop, electric brake is changed to control mode where torque is reduced at a low speed. Gradient is controlled by estimating the load torque of motor, thereby traction motor is not rotated after stop. In addition, coasting operation and brake test are performed from normal-opposite operation and start using a small-scale model comprising the inertial load equipment and the power converter. Further, traction motor is made to be equipped with a suspension torque. Pure electric braking that makes traction motor stop by an air brake at the time of stop is also implemented. Constant torque range and constant power range are expanded during braking so that braking force is secured with the electric brakes even in high speed region. Therefore, vehicle reduction effect can be expected by reducing parts related with an air brake which is not used frequently by using a pure electric brake in the M car in wide speed region. Further, maintenance of brake system can be reduced. Besides, ride comfort of passenger in the electric rail car, energy efficiency improvement, and noise reduction effect can be additionally expected. Further, an improved brake method that uses only an electric brake till motor stop is proposed by comparing those in the blending brake that uses an air brake while reducing brake torque at vehicle stop.
文摘This paper describes in detail three kinds of typical compound braking strategy of wheel motor drive electric vehicle and summarizes the current commonly used strategies based on the three typical strategies developed. In the end, a new compound braking strategy is proposed;that is, we take braking mode classify, ECE regulations and SOC value of the battery as an important reference of braking force that joins the motor braking force, as well as we join the different identification models;according to the different braking modes, the purpose is that we can apply the different braking program.
基金supported by National Key Technology Research and Development Program of China (Grant No. 2007BAF10B00)
文摘Rising concern in environmental issues on global scale has made energy saving in powered equipment a very important subject.In order to improve the energy efficiency and driving range of a motor hoist,a regenerative braking system is designed and discussed.The system takes a unique ultracapacitor-only approach to energy storage system.The bi-directional bride DC？DC converter which regulates current flow to and from the ultracapacitor operates in two modes：boost and buck,depending on the direction of the flow.In order to provide constant input and output current at the ultracapacitor,this system uses a double proportional-integral（PI） control strategy in regulating the duty cycle of PWM to the DC？DC converter.The permanent magnet synchronous motor（PWSM） drive system is also studied.The space vector pulse width modulation（SVPWM） technique,along with a two-closed-loop vector control model,is adopted after detailed analysis of PMSM characteristics.The overall model and control strategy for this regenerative braking system is ultimately built and simulated under the MATLAB and Simulink environment.A test platform is built to obtain experimental results.Analysis of the results reveals that more than half of the gravitational potential energy can be recovered by this system.Simulation and experimentation results testify the validity of the double PI control strategy for interface circuit of ultracapacitor and SVPWM strategy for PMSM.
文摘选择了配备有P1和P3的双电机插电式混合动力汽车(plug-in hybrid electric vehicle,PHEV)作为研究平台。在能量回收过程中,P1和P3电机可以同时进行,相比其他构型而言有着更加明显的能量回收优势。车辆制动过程中,当P1电机效率高于P3时,优先选用P1电机进行制动,P3电机提供剩余所需制动力;当P3电机效率高于或等于P1时,则优先选用P3电机进行制动,P1电机弥补剩余所需的制动力。以搭载AMT(电控机械制动变速箱)的双电机插电式混合动力汽车为研究对象,在保证制动安全性的前提下,为尽可能地回收能量,提出一种基于双电机能量回收的前后轴制动力分配、机电制动力分配以及双电机制动力分配的多级制动力分配策略。结合Matlab/Simulink搭建整车模型,并进行仿真分析。仿真结果显示,制动能量回收率最高能达到66.56%,回收效果良好。
