A novel binder system for hardmetal powder extrusion moulding (PEM) process has been developed. The binder system comprises a major fraction of a mixture of low molecular weight components (LMWCs) and a minor fraction...A novel binder system for hardmetal powder extrusion moulding (PEM) process has been developed. The binder system comprises a major fraction of a mixture of low molecular weight components (LMWCs) and a minor fraction of very finely dispersed polymer. The feedstocks are mixed as a thick slurry at a suitable temperature and are rapidly homogenized by stirring at an adequate shear force. The binders are removed by thermal debinding. The thermal debinding mechanism has been investigated by thermogravimetry (TG) and differential thermogravimetry (DTG). At the first stage of debinding, the LMWCs are removed. These open up pore channels which allows much faster removal of the remaining polymer component during the subsequent stage. The microstructures of the moulded green parts were observed by scanning electron microscopy (SEM). The debound samples were sintered at different temperatures, and the sintered samples properties were measured.展开更多
Most of dental implants are made from titanium or titanium based alloys.However, one of the drawback of such implants is high cost due to the technological difficulties in casting method or machining.In this work, pow...Most of dental implants are made from titanium or titanium based alloys.However, one of the drawback of such implants is high cost due to the technological difficulties in casting method or machining.In this work, powder injection moulding（PIM） method has been used in order to explore lower cost implants without minimising the biocorrosion resistance of the titanium.Corrosion resistance of titanium specimens, produced by powder injection moulding method（PIM-Ti）, in physiologic serum and artificial saliva was investigated.Commercially pure bulk Ti（CP-Ti） was used as control sample.Surface oxidation was also carried out to both PIMTi and CP-Ti samples.Microstructure and corrosion resistance were investigated using microhardness, X-ray diffraction（XRD）, scanning electron microscopy（SEM） and potentiodynamic polarization experiments.Resulting microstructure of PIM-Ti samples contained porosity as compared to CP-Ti control samples.Microhardness of PIM-Ti samples varied with varying applied load whereas it was free from applied load for CP-Ti control samples.Polarisation measurements and SEM analysis revealed that corrosion behaviour of PIM-Ti was reasonably as good as CP-Ti both in as-produced and oxidized conditions in physiologic serum and artificial saliva in spite of its porous structure.展开更多
基金This research was supported by the National Natural Science Foundation of China (grant No.5964120, No.69971007). The financial support is gratefully acknowledged.
文摘A novel binder system for hardmetal powder extrusion moulding (PEM) process has been developed. The binder system comprises a major fraction of a mixture of low molecular weight components (LMWCs) and a minor fraction of very finely dispersed polymer. The feedstocks are mixed as a thick slurry at a suitable temperature and are rapidly homogenized by stirring at an adequate shear force. The binders are removed by thermal debinding. The thermal debinding mechanism has been investigated by thermogravimetry (TG) and differential thermogravimetry (DTG). At the first stage of debinding, the LMWCs are removed. These open up pore channels which allows much faster removal of the remaining polymer component during the subsequent stage. The microstructures of the moulded green parts were observed by scanning electron microscopy (SEM). The debound samples were sintered at different temperatures, and the sintered samples properties were measured.
文摘Most of dental implants are made from titanium or titanium based alloys.However, one of the drawback of such implants is high cost due to the technological difficulties in casting method or machining.In this work, powder injection moulding（PIM） method has been used in order to explore lower cost implants without minimising the biocorrosion resistance of the titanium.Corrosion resistance of titanium specimens, produced by powder injection moulding method（PIM-Ti）, in physiologic serum and artificial saliva was investigated.Commercially pure bulk Ti（CP-Ti） was used as control sample.Surface oxidation was also carried out to both PIMTi and CP-Ti samples.Microstructure and corrosion resistance were investigated using microhardness, X-ray diffraction（XRD）, scanning electron microscopy（SEM） and potentiodynamic polarization experiments.Resulting microstructure of PIM-Ti samples contained porosity as compared to CP-Ti control samples.Microhardness of PIM-Ti samples varied with varying applied load whereas it was free from applied load for CP-Ti control samples.Polarisation measurements and SEM analysis revealed that corrosion behaviour of PIM-Ti was reasonably as good as CP-Ti both in as-produced and oxidized conditions in physiologic serum and artificial saliva in spite of its porous structure.
