THE MULTI-LAYER LASER CLADDING OF Ni60 ALLOY

The Multi layer coating of Ni60 alloy was got by multi layer laser cladding. The height of the coating was about 12mm and the wall of the coating was perpendicular to the base. The microstructure of the coating was made up of fine dendrite. The conjunction between layers was good.

Inversion of thicknesses of multi-layered structures from eddy current testing measurements

Luquire et al. ' s impedance change model of a rectangular cross section probe coil above a structure with an arbitrary number of parallel layers was used to study the principle of measuring thicknesses of multi-layered structures in terms of eddy current testing voltage measurements. An experimental system for multi-layered thickness measurement was developed and several fitting models to formulate the relationships between detected impedance/voltage measurements and thickness are put forward using least square method. The determination of multi-layered thicknesses was investigated after inversing the voltage outputs of the detecting system. The best fitting and inversion models are presented.

XTEM STUDY ON ION PLATED STAINLESS STEEL MULTI-LAYER FILMS

In this paper, the cross sectional microstructure and crystal structure of ion plated multi layer films of stainless steel (1Cr18Ni9Ti ) were studied by cross sectional transmission electron microscopy (XTEM). The results show that ion plated stainless steel multi layer films are fine grained double phase steel films of austenites and ferrites.Cross section film growing microstructures can be divided into three zones: fine equiaxed crystals, fine columnar crystals and coarse columnar crystals. Interfaces in multi layer films can promote fine grained growing and interrupt columnar grained growing,and improve properties of film materials.

A Kind of Second-Order Learning Algorithm Based on Generalized Cost Criteria in Multi-Layer Feed-Forward Neural Networks

A kind of second order algorithm--recursive approximate Newton algorithm was given by Karayiannis. The algorithm was simplified when it was formulated. Especially, the simplification to matrix Hessian was very reluctant, which led to the loss of valuable information and affected performance of the algorithm to certain extent. For multi layer feed forward neural networks, the second order back propagation recursive algorithm based generalized cost criteria was proposed. It is proved that it is equivalent to Newton recursive algorithm and has a second order convergent rate. The performance and application prospect are analyzed. Lots of simulation experiments indicate that the calculation of the new algorithm is almost equivalent to the recursive least square multiple algorithm. The algorithm and selection of networks parameters are significant and the performance is more excellent than BP algorithm and the second order learning algorithm that was given by Karayiannis.

Engineering Study on the Treatment of Multi-soil-layering System on the Rural Domestic Wastewater in Taihu Basin

By combining with the actual situation in the rural area,the practical technology of domestic wastewater treatment which had the wide popularization value was developed in the rural area of Taihu Basin.Moreover,the multi-soil-layering system was used to treat the concentrated rural domestic wastewater,and the demonstration project was established in Fenshui Village,Yixing,Jiangsu.The result showed that the infrastructure and operating cost of system was low,and the treatment effect was good.The average removal ratios of COD,NH+4-N,TN,TP and SS were respectively 70%,83%,59%,76% and 94%.The quality of yielding water could reach Grade A standard of Pollutant Emission Standards in Urban Wastewater Treatment Plant.

Structural Analysis of the Multi-layer Detachment Folding in Eastern Sichuan Province

A serial of＂comb-like and trough-like＂folds developed in eastern Sichuan,controlled by the multi-layer detachment folding,is different from the classical Jura-type structure in their development.The key factor resulting in the development of these structures is the occurrence of detachment layers in different parts of Neoprotozoic to Mesozoic stratigraphy of study area,which, from the bottom to the top,are the lower part of Banxi Group,Lower Cambrian（Niutitang Formation）,Lower Silurian（Longmaxi Formation and Luoreping Formation）,Upper Permian （Wujiaping Formation） and Lower Triassic（Daye Formation）.On the basis of field survey combined with sand-box modeling,this study argued that the detachment layer of the lower part of Banxi Group controlled the development of the＂comb-like＂folds,and the lower part of Cambrian detachment layer controlled the development of＂trough-like＂folds.Because of several detachment layers occurring in the study area,the development of duplex structures different scales is an important deformation mechanism,and the duplexes are the important structures distinguished from the typical detachment folding structures.Due to these duplexes,the surface structures and structural highs may not be the structural highs in the depth.Meanwhile,the detachment layers are good channels for oil/ gas migration benefiting the understanding of accumulation and migration of oil and gas.

Measurement of residual stress in a multi-layer semiconductor heterostructure by micro-Raman spectroscopy

Si-based multilayer structures are widely used in current microelectronics. During their preparation, some inhomogeneous residual stress is induced, resulting in competition between interface mismatching and surface energy and even leading to structure failure. This work presents a methodological study on the measurement of residual stress in a multi-layer semiconductor heterostructure. Scanning electron microscopy（SEM）, micro-Raman spectroscopy（MRS）, and transmission electron microscopy（TEM） were applied to measure the geometric parameters of the multilayer structure. The relationship between the Raman spectrum and the stress/strain on the [100] and [110] crystal orientations was determined to enable surface and crosssection residual stress analyses, respectively. Based on the Raman mapping results, the distribution of residual stress along the depth of the multi-layer heterostructure was successfully obtained.

Optimum Design for Shrink-fit Multi-layer Vessels under Ultrahigh Pressure Using Different Materials

Multi-layer pressure vessels are widely used in every field of high pressure technology.For the purpose of enhancing a vessels＇ load bearing capacity,a beneficial process like shrink-fit is usually employed.However,few documents on optimum design for multi-layer shrink-fit vessels made of different strength materials can be found,available data are mainly on two-layer vessels.In this paper,an optimum design approach is developed for shrink-fit multi-layer vessels under ultrahigh pressure by using different materials.Maximum shear stress theory is applied as design criteria.The inner and outer radii of a multi-layer vessel,as well as the material of each layer,are assumed to be known.The optimization mathematical model is,thereby,built.Lagrange multipliers method is required to obtain the optimal design formula of wall ratio（ratio of outer to inner radii） of each layer,from which the optimum formulas of shrinkage pressure and radial interference are derived with the superposition principle employed.These formulas are applicable for the optimization design of all multi-layer vessels made of different materials,or same materials.The formulas of the limit working pressure and the contact pressure show that the optimum wall ratio of each layer and limit working pressure are only related to all selected material strength and unrelated to the position of the layer placement in the vessel.However,shrinkage pressure is related to the position of the layer placement in the vessel.Optimization design of an open ended shrink-fit three-layer vessel using different materials and comparisons proved that the optimized multi-layer vessels have outstanding characteristics of small radial interference and are easier for assembly.When the stress of each layer is distributed more evenly and appropriately,the load bearing capability and safety of vessels are enhanced.Therefore,this design is material-saving and cost-effective,and has prospect of engineering application.

Three-Dimensional Modelling of a Multi-Layer Sandstone Reservoir： the Sebei Gas Field, China

Multi-layer sandstone reservoirs occur globally and are currently in international production. The 3D characteristics of these reservoirs are too complicated to be accurately delineated by general structural-facies-reservoir modelling. In view of the special geological features, such as the vertical architecture of sandstone and mudstone interbeds, the lateral stable sedimentation and the strong heterogeneity of reservoir poroperm and fluid distribution, we developed a new three-stage and six-phase procedure for 3D characterization of multi-layer sandstone reservoirs. The procedure comprises two-phase structural modelling, two-phase facies modelling and modelling of two types of reservoir properties. Using this procedure, we established models of the formation structure, sand body structure and microfacies, reservoir facies and properties including porosity, permeability and gas saturation and provided a 3D fine-scale, systematic characterization of the Sebei multi-layer sandstone gas field, China. This new procedure, validated by the Sebei gas field, can be applied to characterize similar multi-layer sandstone reservoirs.

A multi-layered Ti3C2/Li2S composite as cathode material for advanced lithium-sulfur batteries

Lithium-sulfur(Li-S)batteries with lithium sulfide(Li2S)as cathode have attracted great attention recently,because of high specific capacity(1166 mA h g^-1)of Li2S and potential safety of using Li metal-free anode.Li2S cathode has lower volume expansion and higher thermal stability than the traditional sulfur cathode.However,the problems of"shuttle effect"and poor electrical conductivity of the cathode material still need to be overcome.In this work,multi-layered Ti3C2/Li2S(ML-Ti3C2/Li2S)composite has been prepared and applied as a cathode in advanced Li-S batteries.The unique multi-layer sheet structure of Ti3 C2 provides space for the storage of Li2S,and its good conductivity greatly enhances the usage ratio of Li2 S and improves the conductivity of the whole Li2S cathode.Compared with commonly used graphene,ML-Ti3C2 can trap polysulfides effectively by chemical adsorption and also activate the reaction of Li2S to polysulfides by forming Ti-S bond.As a result,during the cycling of the batteries with ML-Ti3C2/Li2S cathodes,the activation voltage barrier of the first cycle has decreased to 2.8 V,and the"shuttle effect"has been suppressed effectively.The cycling and rate performances of the ML-Ti3C2/Li2S cathodes have been significantly improved compared to that of graphene/Li2 S cathodes.They maintain a capacity of 450 mAh g^-1 at 0.2 C after 100 cycles,and deliver attractive rate performances of 750,630,540,470 and 360 mAh g^-1 at 0.1 C,0.2 C,0.5 C,1 C,and 2 C,respectively.

Energy Absorption Diagrams of Multi-layer Corrugated Boards

Based on the static compression experiments, the compressive stress-strain curve of multi-layer corrugated boards is simplified into three sections of linear elasticity, sub-buckling going with local collapse and densification. By considering the structure factors of multi-layer corrugated boards, the energy absorption model is obtained and characterized by the structure factors of corrugated cell-wall. The model is standardized by the solid modulus and it is universal for corrugated structures of different basis material. In the liner-elastic section, with the increase of the load, the energy absorption per unit volume of multi-layer corrugated boards gradually increases; in the sub-buckling section going with local collapse, the compression resistance of multi-layer corrugated boards goes on under a nearly constant load, but the energy absorption per unit volume rapidly increases with the increase of the compression strain. It is shown as an ascending curve in the energy absorption diagram. In the densification section, the corrugated sandwich core has no energy absorption capability. A good consistency is achieved between theoretical and experimental energy absorption curves. In designing the cushioning package, the cushioning properties can be evaluated by the theoretical model without more experiments. The suggested method to develop the energy absorption diagram for corrugated boards can be used to characterize the cushioning properties and optimize the structures of corrugated sandwich structures.

Arnol＇d＇s Second Nonlinear Stability Theorem for General Multilayer Quasi－geostrophic Model

Arnol'd's second nonlinear stability criterion for motions governed by a general multilayer quasi-geostrophic model is established. The model allows arbitrary density jumps and layer thickness, and at the top and the bottom of the nuid, the boundary condition is either free or rigid. The criterion is obtained by the establishment of the upper bounds of disturbance energy and potential enstrophy in terms of the initial disturbance field.

FE simulation and process analysis on forming of aluminum alloy multi-layer cylinder parts with flow control forming

The aluminum alloy parts used in airbag of car were studied with flow control forming(FCF) method, which was a good way to low forming force and better mechanical properties. The key technology of FCF was the design of control chamber to divide metal flow. So, the design method of FCF was analyzed and two type of control chamber were put forward. According to divisional principle, calculation model of forming force and approximate formula were given. Then forming process of aluminum alloy multi-layer cylinder parts was simulated. The effect of friction factor, die radius and punch velocity on metal flow and forming force was obtained. Finally, the experiment was preformed under the direction of theory and finite element(FE) simulation results. And the qualified parts were manufactured. The simulation data and experimental results show that the forming sequence of inner wall and outer wall, and then the force step, can be controlled by adjusting the process parameters. And the FCF technology proposed has very important application value in precision forging.

Seismogram Synthesis in Multi-layered Half-space Part Ⅰ. Theoretical Formulations

In the past two decades numerous studies were made to develop and improve the theory and practical computation techniques of synthesizing theoretical seismograms for the model of multi-layered half-space. Today, synthesizing theoretical seismograms in multi-layered half-space is an important tool for understanding the structure of the Earth’s interior as well as the seismic source process from well-recorded seismograms data. As part of a review of the state-of-the-art, in this article I shall present a systematic and self-contained theory of elastic waves in multi-layered half-space media based on the developments in the past two decades.

Multi-layer Tectonic Model for Intraplate Deformation and Plastic-Flow Network in the Asian Continental Lithosphere

In a large area of the east—central Asian continent there is a unified seismic network system composed of two families of large—seismic belts that intersect conjugately. Such a seismic network in the middle—upper crust is actually a response to the plastic flow network in the lower lithosphere including the lower crust and lithospheric mantle. The existence of the unified plastic flow system confirms that the driving force for intraplate tectonic deformation results mainly from the compression of the India plate, while the long-range transmission of the force is carried out chiefly by means of plastic flow. The plastic flow network has a control over the intraplate tectonic deformation.

Research on the process of fabricating a multi-layer metal micro-structure based on UV-LIGA overlay technology

In this paper,we report the study of the process of fabricating a multi-layermetal micro-structure using UV-LIGA overlay technology,includingmask fabrication,substrate treatment,and UV-LIGA overlay processes.To solve the process problems in the masking procedure,the swelling problemof the first layer of SU-8 thick photoresist was studied experimentally.The 5μmline-width compensation and closed 20μmand 30μmisolation strips were designed and fabricated around the micro-structure pattern.The pore problemin the Ni micro-electroforming layer was analyzed and the electroforming parameters were improved.The pH value of the electroforming solution should be controlled between 3.8 and 4.4 and the current density should be below 3 A/dm^2.To solve the problems of high inner stress and incomplete development of the micro-cylinder hole array with a diameter of 30μm,the lithography process was optimized.The pre-baking temperature was increased via gradient heating and rose every 5℃ from 65℃ to 85℃ and then remained at 85℃ for 50 min–1 h.In addition,the full contact exposure was used.Finally,a multi-layer metal micro-structure with high precision and good quality of microelectroforming layer was fabricated using UV-LIGA overlay technology.

Design of multi-layered porous fibrous metals for optimal sound absorption in the low frequency range

We present a design method for calculating and optimizing sound absorption coefficient of multi-layered porous fibrous metals （PFM） in the low frequency range. PFM is simplified as an equivalent idealized sheet with all metallic fibers aligned in one direction and distributed in periodic hexagonal patterns. We use a phenomenological model in the literature to investigate the effects of pore geometrical parameters （fiber diameter and gap） on sound absorption performance. The sound absorption coefficient of multi- layered PFMs is calculated using impedance translation theorem, To demonstrate the validity of the present model, we compare the predicted results with the experimental data. With the average sound absorption （low frequency range） as the objective function and the fiber gaps as the design variables, an optimization method for multi-layered fibrous metals is proposed. A new fibrous layout with given porosity of multi-layered fibrous metals is suggested to achieve optimal low frequency sound absorption. The sound absorption coefficient of the optimal multi-layered fibrous metal is higher than the single- layered fibrous metal, and a significant effect of the fibrous material on sound absorption is found due to the surface Dorosity of the multi-layered fibrous.

Laplacian energy maximizationfor multi-layer air transportation networks

To increase airspace capacity, alleviate flight delay,and improve network robustness, an optimization method of multi-layer air transportation networks is put forward based on Laplacian energy maximization. The effectiveness of taking Laplacian energy as a measure of network robustness is validated through numerical experiments. The flight routes addition optimization model is proposed with the principle of maximizing Laplacian energy. Three methods including the depth-first search( DFS) algorithm, greedy algorithm and Monte-Carlo tree search( MCTS) algorithm are applied to solve the proposed problem. The trade-off between system performance and computational efficiency is compared through simulation experiments. Finally, a case study on Chinese airport network( CAN) is conducted using the proposed model. Through encapsulating it into multi-layer infrastructure via k-core decomposition algorithm, Laplacian energy maximization for the sub-networks is discussed which can provide a useful tool for the decision-makers to optimize the robustness of the air transportation network on different scales.

The compound Poisson risk model with dependence under a multi-layer dividend strategy

In this paper, a compound Poisson risk model with time-dependent claims is studiedunder a multi-layer dividend strategy. A piecewise integro-differential equation for the Gerber- Shiu function is derived and solved. Asymptotic formulas of the ruin probability are obtained when the claim size distributions are heavy-tailed.

In-plane dynamic Green's functions for inclined and uniformly distributed loads in a multi-layered transversely isotropic half-space

The dynamic stiffness method combined with the Fourier transform is utilized to derive the in-plane Green’s functions for inclined and uniformly distributed loads in a multi-layered transversely isotropic（TI）half-space.The loaded layer is fixed to obtain solutions restricted in it and the corresponding reactions forces,which are then applied to the total system with the opposite sign.By adding solutions restricted in the loaded layer to solutions from the reaction forces,the global solutions in the wavenumber domain are obtained,and the dynamic Green’s functions in the space domain are recovered by the inverse Fourier transform.The presented formulations can be reduced to the isotropic case developed by Wolf（1985）,and are further verified by comparisons with existing solutions in a uniform isotropic as well as a layered TI halfspace subjected to horizontally distributed loads which are special cases of the more general problem addressed.The deduced Green’s functions,in conjunction with boundary element methods,will lead to significant advances in the investigation of a variety of wave scattering,wave radiation and soil-structure interaction problems in a layered TI site.Selected numerical results are given to investigate the influence of material anisotropy,frequency of excitation,inclination angle and layered on the responses of displacement and stress,and some conclusions are drawn.