MULTI-SCALE AND MULTI-PHASE NANOCOMPOSITE CERAMIC TOOLS AND CUTTING PERFORMANCE

An advanced ceramic cutting tool material Al2O3/TiC/TiN （LTN） is developed by incorporation and dispersion of micro-scale TiC particle and nano-scale TiN particle in alumina matrix. With the optimal dispersing and fabricating technology, this multi-scale and multi-phase nanocomposite ceramic tool material can get both higher flexural strength and fracture toughness than that of A1203/TiC （LZ） ceramic tool material without nano-scale TiN particle, especially the fracture toughness can reach to 7.8 MPa . m^0.5. The nano-scale TiN can lead to the grain fining effect and promote the sintering process to get a higher density. The coexisting transgranular and intergranular fracture mode induced by micro-scale TiC and nano-scale TiN, and the homogeneous and densified microstructure can result in a remarkable strengthening and toughening effect. The cutting performance and wear mechanisms of the advanced multi-scale and multi-phase nanocomposite ceramic cutting tool are researched.

Sentinel-1/2影像在兰州北山削山造地范围识别中的应用

城市空间发展易受地形所限,削山造地能克服土地资源稀缺,成为解决城市空间拓展最为直接的途径。该方法利用遥感技术快速准确获取削山造地范围信息,对区域生态环境科学评估和新城发展规划具有十分重要的意义。本文基于GEE遥感云计算平台,利用Sentinel-1合成孔径雷达(synthetic aperture Rader,SAR)数据,采用组合升、降轨影像,在噪声滤除和多时相影像合成的基础上,计算削山造地前后后向散射强度的差值,并采用百分位阈值法结合样本数据确定阈值,提取研究区2017—2022年削山造地开挖区时空分布;然后联合SAR和光学数据的光谱特征、纹理特征和地形特征,在特征优化的基础上结合随机森林算法获取了2017—2022年逐年削山造地范围时空分布。研究结果表明:①提取的开挖区范围总体分类精度和Kappa系数分别达85%和0.83。②研究期间,发现2019年前开挖区主要集中在九州开发区、碧桂园和保利领秀山,2020年以后新增加了刘家沟、水源站等开挖区,开挖范围和强度逐渐增大。③2018年前造地规模较小,面积为2.655 km 2;2019年以后造地规模逐年增大,特别是2021年,其造地面积达12.607 km 2,占监测期间总造地面积的34.56%,2022年在原造地基础上开挖,因坡度和开挖量逐渐增大,造地面积仅2.686 km 2。本文构建的削山造地开挖区监测和造地范围提取方法可有效获取削山和造地范围快速监测与提取。

Human-induced landslide on a high cut slope: a case of repeated failures due to multi-excavation

The paper attempts to represent a case of repeated failures on a high cut slope due to multi-excavation. The characteristics of each failure induced by excavation are analyzed through geological investigation, and then a geological model at different failure stages is proposed. The geological analysis shows that the excavation-induced repeated failures are related to the exposure of the weak bedding plane and the toe unloading of the cut slope, Numerical modeling is conducted based on a sequential method, taking into account the main failure stages of cut slope. The simulation results fairly coincide with the practical phenomena observed in field. It is shown that the decrease in normal stress of displaced mass on cut slope will induce the increase in shear stress in bedding planes and that at the toe of the cut slope. The released stress leads to repeated gravitational instabilities of cut slope due to the decrease in normal stress and the increase in shear stress along the bedding planes of mudstone.

A Comparative Study of Acute Hemodynamic Effects of Multi -site Cardiac Pacing in patients with cardiac function NYHA class ⅠtoⅡ without bundle branch block

Objective To compare the acute hemodynamic effects of five different pacing modes in patients with cardiac function NYHA class Ⅰ to Ⅱ without bundle branch block (BBB). Methods This study included 12 patients (SSS 7, Ⅲ°AVB 5) undergoing pacemaker implantation. Right ventricular apex (RVA), right ventricular outflow tract (RVOT), right ventricular bifocal (RV-Bi), left ventricular base (LVB) and bi -ventricular (Bi-Ⅴ) pacing at 60 -80 ppm were done in VVI mode prior to implantation of DDD pacemaker. The cardiac index (CI), mean pulmonary artery pressure (mPAP) and pulmonary capillary wedge pressure (PCWP) were measured with Swan - Ganz thermodilution catheter after 5 minutes of each pacing mode. Results (1) Comparing to pacing at RVA (CI: 2. 41± 0. 38 L/min per m2, PCWP: 16. 7 ±3.3 mmHg), the CI increased and the PCWP decreased significantly in pacing at RVOT(CI: 2. 63 ± 0.46, PCWP: 13. 8±2. 3), LVB(CI: 2. 78±0.52, PCWP: 14. 4±3.1), RV-Bi(CI: 2. 83±0.57, PCWP: 12. 8± 2. 5) and Bi -Ⅴ pacing (CI: 2. 94± 0.60, PCWP: 12. 7±2. 5), P < 0. 01, respectively. (2) The CI of RV-Bi and Bi-Ⅴ pacing was higher than that of RVOT and LVB pacing, the PCWP was lower, P < 0. 05, respectively. (3) There was no significant difference between RV - Bi pacing and Bi-Ⅴ pacing in CI and PCWP. Conclusion There is no significant difference between RV - Bi pacing and Bi -V pacing in the acute hemodynamic effects; however,dual - site pacing is much better than single site pacing in that aspect for patients with cardiac function NYHA class Ⅰ to Ⅱ without BBB. Among single site pacing, the RVOT and LVB pacing is better than RVA pacing in cardiac function.

Preliminary Study on Water Demand Law of 1-0 Rooted Cuttings of Populus szechuanica

In order to provide theoretical basis and technical support for the afforestation and artificial water supply of P.szechuanica in arid areas,the characteristics of water consumption of P.szechuanica were explored,and the law of water demand of P.szechuanica was grasped.In this paper,potted seedlings of 1-0 rooted cuttings of P.szechuanica were taken as research objects,and change situation of water consumption under different water control gradients was measured regularly by using weighing method,further analyzing dynamic change of water consumption of P.szechuanica and revealing water demand law of 1-0 rooted cuttings of P.szechuanica.The results showed that total change of water consumption of 1-0 rooted cuttings of P.szechuanica had"slow-fast-slow-fast"double-peak trend in the growth period of the current year,and corresponded with univariate linear relation(R^(2)=0.7137),with significant difference.In whole growth period,water consumption in August was the highest,which was 2.7 times of that in June and July and 1.5 times of that after September.In different water control treatments,the dynamic changes of daily and monthly water consumption were significantly different.In seven water control treatments,monthly water consumption was between(6315.95±1690.70)and(10105.28±3065.30)g/month,and mean was(8211.07±2308.23)g/month.With intensification of water control treatment,water consumption increased,but there was no seedling death due to water shortage.P.szechuanica has great plasticity in water demand,and can survive in both arid and humid environments.Meanwhile,it is revealed that P.szechuanica is the most widely distributed tree species in the region.

A Branch and Cut Algorithm for Two-Echelon Inventory Routing Problem with End-of-Tour Replenishment Policy

This study presents a two-echelon inventory routing problem (2E-IRP) with an end-of-tour replenishment (ETR) policy whose distribution network consists of a supplier, several distribution centers (DCs) and several retailers on a multi-period planning horizon. A formulation of the problem based on vehicle indices is proposed in the form of a mixed integer linear program (MILP). The mathematical model of the problem is solved using a branch and cut (B&C) algorithm. The results of the tests are compared to the results of a branch and price (B&P) algorithm from the literature on 2E-IRP with a classical distribution policy. The results of the tests show that the B&C algorithm solves 197 out of 200 instances (98.5%). The comparison of the B&C and B&P results shows that 185 best solutions are obtained with the B&C algorithm on 197 instances (93.9%). Overall, the B&C algorithm achieves cost reductions ranging from 0.26% to 41.44% compared to the classic 2E-IRP results solved with the B&P algorithm, with an overall average reduction of 18.08%.

一般图上的限制性k node multi-multiway cut问题的启发式算法

限制性k node multi-multiway cut问题作为multiway cut问题的自然推广是NP难的。论文研究了一般图上的限制k node multi-multiway cut问题,首先用LP-relaxation和LP-rounding技术确定至少断开的k个终端集合,其次用改进的域增长技术将求得的分数解调整为整数解从而设计了该问题的一个启发式算法。

Multi-features Based Approach for Moving Shadow Detection

In the video-based surveillance application, moving shadows can affect the correct localization and detection of moving objects. This paper aims to present a method for shadow detection and suppression used for moving visual object detection. The major novelty of the shadow suppression is the integration of several features including photometric invariant color feature, motion edge feature, and spatial feature etc. By modifying process for false shadow detected, the averaging detection rate of moving object reaches above 90% in the test of Hall-Monitor sequence.

The Large Sky Area Multi-Object Fiber Spectroscopic Telescope (LAMOST)

The Large Sky Area Multi-Object Fiber Spectroscopic Telescope (LAMOST, also called the Guo Shou Jing Telescope) is a special reflecting Schmidt telescope. LAMOST’s special design allows both a large aperture (effective aperture of 3.6 m–4.9 m) and a wide field of view (FOV) (5°). It has an innovative active reflecting Schmidt configuration which continuously changes the mirror’s surface that adjusts during the observation process and combines thin deformable mirror active optics with segmented active optics. Its primary mirror (6.67m×6.05 m) and active Schmidt mirror (5.74m×4.40 m) are both segmented, and composed of 37 and 24 hexagonal sub-mirrors respectively. By using a parallel controllable fiber positioning technique, the focal surface of 1.75 m in diameter can accommodate 4000 optical fibers. Also, LAMOST has 16 spectrographs with 32 CCD cameras. LAMOST will be the telescope with the highest rate of spectral acquisition. As a national large scientific project, the LAMOST project was formally proposed in 1996, and approved by the Chinese government in 1997. The construction started in 2001, was completed in 2008 and passed the official acceptance in June 2009. The LAMOST pilot survey was started in October 2011 and the spectroscopic survey will launch in September 2012. Up to now, LAMOST has released more than 480 000 spectra of objects. LAMOST will make an important contribution to the study of the large-scale structure of the Universe, structure and evolution of the Galaxy, and cross-identification of multiwaveband properties in celestial objects.

Layer regrouping for water-flooded commingled reservoirs at a high water-cut stage

Layer regrouping is to divide all the layers into several sets of production series according to the physical properties and recovery percent of layers at high water-cut stage, which is an important technique to improve oil recovery for high water-cut multilayered reservoirs. Dif- ferent regroup scenarios may lead to different production performances. Based on unstable oil-water flow theory, a multilayer commingled reservoir simulator is established by modifying the production split method. Taking into account the differences of layer properties, including per- meability, oil viscosity, and remaining oil saturation, the pseudo flow resistance contrast is proposed to serve as a characteristic index of layer regrouping for high water-cut multilayered reservoirs. The production indices of multi- layered reservoirs with different pseudo flow resistances are predicted with the established model in which the data are taken from the Shengtuo Oilfield. Simulation results show that the pseudo flow resistance contrast should be less than 4 when the layer regrouping is implemented. The K-means clustering method, which is based on the objec- tive function, is used to automatically carry out the layer regrouping process according to pseudo flow resistances. The research result is applied to the IV-VI sand groups of the second member of the Shahejie Formation in the Shengtuo Oilfield, a favorable development performance is obtained, and the oil recovery is enhanced by 6.08 %.

Optimization of Cutting Parameters in Helical Milling of Carbon Fiber Reinforced Polymer

To investigate cutting performance in the helical milling of carbon fiber reinforced polymer(CFRP),experiments were conducted with unidirectional laminates.The results show that the influence of cutting parameters is very significant in the helical milling process. The axial force increases with the increase of cutting speed, which is below 95 m/min; otherwise, the axial force decreases with the increase of cutting speed. The resultant force always increases when cutting speed increases; with the increase of tangential and axial feed rates, cutting forces increase gradually. In addition, damage rings can appear in certain regions of the entry edges; therefore, the relationship between machining performance(cutting forces and holemaking quality) and cutting parameters is established using the nonlinear fitting methodology. Thus, three cutting parameters in the helical milling of CFRP, under the steady state, are optimized based on the multi-objective genetic algorithm, including material removal rate and machining performance. Finally, experiments were carried out to prove the validity of optimized cutting parameters.

An effective multi-level algorithm based on ant colony optimization for graph bipartitioning

Partitioning is a fundamental problem with applications to many areas including data mining, parellel processing and Very-large-scale integration （VLSI） design. An effective multi-level algorithm for bisecting graph is proposed. During its coarsening phase, an improved matching approach based on the global information of the graph core is developed with its guidance function. During the refinement phase, the vertex gain is exploited as ant＇s heuristic information and a positive feedback method based on pheromone trails is used to find the global approximate bipartitioning. It is implemented with American National Standards Institute （ANSI） C and compared to MeTiS. The experimental evaluation shows that it performs well and produces encouraging solutions on 18 different graphs benchmarks.

钛合金切削温度-振动相关性及加工优化研究

钛合金作为“21世纪战略金属”在航空领域应用广泛,其加工质量至关重要。因此,对钛合金进行切削加工优化具有重要的研究意义。本文搭建切削温度和切削振动同步测量系统。通过红外热像仪和三向加速度传感器采集车刀尖端附近的温度和振动信号。建立基于切削温度和切削振动多特征融合优化模型,并运用粒子群优化灰狼算法对多特征融合优化模型进行求解,获得最优的切削参数。研究表明:在试验设计的切削参数范围内,切削参数的最优解为:切削速度753.98 m/s,进给速度30 mm/min,切削深度0.4 mm,所做研究为优化钛合金加工质量提供理论指导。

Research on A Master - slave Multi - microcomputers Control System for Hollow Spindle Fancy Yarn Spinning Machine

In this paper, a successfully studied and developed master - slave muld - microcomputers control system based on PC - BUS for hollow spindle fancy yarn spinning machine, mainly Its overall scheme, software and hardware construction, is introduced. Spinning experiments show that the system achieves satisfactory result. This system can solve the diftkultles of mechatronical fusion between domestic hollow splndk fancy yarn spuming muchine and its microcomputer control technology.

On the Representation of Multi-layer Woven Structure

A quantitative method is developed to identify the structures of multi-layer woven fabric in this study. Six structural parameters are selected to represent the fabric structure. With some design criteria for the reinforcement of textile composites, the relationships among the structural parameters are derived for different binding patterns of the fabric structure. The conditions, which meet the requirements of structural cell stability,are also discussed.

基于Cut-and-Choose技术的安全多方计算

Cut-and-Choose技术是密码学中一种被广泛使用的密码学工具,对安全多方计算协议的设计起着重要的作用.其主要思想是一方在协议中构造多份混淆电路,另一方要求打开其中一部分电路进行检查,若检查通过则计算剩余的电路,决定电路的最终输出.在早期工作中,Cut-and-Choose技术主要应用于恶意模型下的安全两方计算,并由此产生了许多优秀的工作.尽管该技术在隐蔽安全模型中的工作也很早提出,但在当时并没有引起太多的关注.近年来,随着学者对于隐蔽敌手的深入研究,Cut-and-Choose技术以及基于该技术的思想也开始被用于实现公开可验证的隐蔽安全协议,涌现出一些代表性的工作.首先介绍了Cut-and-Choose技术在恶意安全模型和隐蔽安全模型中的研究进展;其次重点介绍其应用于公开可验证隐蔽安全模型中的研究成果;最后通过对该领域的研究成果进行详细的总结与分析,并指出后续可能的发展方向.

Computer-aided Pattern Design of Multi-bar Warp Knitted Fabrics

To meet the development trend of multi-bar warp knit-ting machine towards high-speed,advanced technologyand computer control and the requirements of variousproducts with small quantity,there are many researcheson the computer-aided pattern design of multi-barwarp knitted fabrics.In terms of the special propertiesof the computer-aided pattern design of multi-barwarp knitted fabrics,the Object Oriented Program(OOP)programming-Object Windows class Library(OWL)programming is selected.According to thecharacters of the OWL programming,various functionsare defined.Pattern design and technical parameters canbe output,which offers a great convenience for the fac-tory.

MODS： A Novel Metaheuristic of Deterministic Swapping for the Multi-Objective Optimization of Combinatorials Problems

This paper states a new metaheuristic based on Deterministic Finite Automata （DFA） for the multi - objective optimization of combinatorial problems. First, a new DFA named Multi - Objective Deterministic Finite Automata （MDFA） is defined. MDFA allows the representation of the feasible solutions space of combinatorial problems. Second, it is defined and implemented a metaheuritic based on MDFA theory. It is named Metaheuristic of Deterministic Swapping （MODS）. MODS is a local search strategy that works using a MDFA. Due to this, MODS never take into account unfeasible solutions. Hence, it is not necessary to verify the problem constraints for a new solution found. Lastly, MODS is tested using well know instances of the Bi-Objective Traveling Salesman Problem （TSP） from TSPLIB. Its results were compared with eight Ant Colony inspired algorithms and two Genetic algorithms taken from the specialized literature. The comparison was made using metrics such as Spacing, Generational Distance, Inverse Generational Distance and No-Dominated Generation Vectors. In every case, the MODS results on the metrics were always better and in some of those cases, the superiority was 100%.

基于RBF-PID的掘进机截齿动载荷平稳性控制方法研究

依据实际情况,运用有限元仿真对掘进机截割头水平截割、垂直截割与纵向钻进工况进行仿真。通过对仿真结果进行统计,得到了各截齿在截割过程中截割阻力的大小,并运用仿真结果对截割阻力计算公式进行了修正。通过建立多目标优化模型,运用NSGA-Ⅱ算法进行求解,得到了不同煤岩硬度下的最优截割参数。以上述研究为基础,提出了基于RBF-PID的掘进机截齿动载荷平稳性控制方法。采用MATLAB与AMESim联合仿真,搭建了截割头转速与摆速控制模型,通过仿真并分析仿真结果,验证了所提出方法的可靠性。

气相色谱-串联质谱法测定卷烟烟丝代表性化学成分

建立了气相色谱-串联质谱(GC-MS/MS)同时测定烟丝中7种代表性化学成分的分析方法。样品用NaOH溶液浸润,经二氯甲烷超声萃取后,在DB-35MS色谱柱上分离,采用多反应监测(MRM)模式测定,内标法定量。结果表明,7种成分的检出限为0.02~2.28mg·kg^(-1),加标回收率为87.7%~96.2%。该方法具有前处理简单、准确灵敏的特点,适用于烟丝的稳定性评价。