Simulation and prototype testing of multi-wire drift chamber arrays for the CEE

The building of a large-scale external-target experiment, abbreviated as CEE, in the cooling storage ring at the Heavy Ion Research Facility in Lanzhou has been planned. The CEE is a multi-purpose spectrometer that will be used for various studies on heavy-ion collisions. A multi-wire drift chamber(MWDC) array is the forward tracking detector of the CEE. In this work, GEANT4 simulations were performed for the MWDC forward tracking array with a focus on the track reconstruction algorithm. Combined with the time of flight information,particle identification is achieved. The residue is about 30 μm, while the tracking efficiency is higher than 90%with the current redundancy. In addition, a prototype of the forward tracking system using three MWDCs was assembled and tested using a high-energy proton beam. The firing efficiency of the detector and the reconstruction accuracy of the prototype were derived. The track residue for the protons at about 400 MeV/c is better than 300 μm, meeting the requirements of the CEE. Suggestions for improving the performance of the forward tracking system are given.

Polar interface and surface optical vibration spectra in multi-layer wurtzite quantum wires： transfer matrix method

The polar interface optical （IO） and surface optical （SO） phonon modes and the corresponding Froehlich electron phonon-interaction Hamiltonian in a freestanding multi-layer wurtzite cylindrical quantum wire （QWR） are derived and studied by employing the transfer matrix method in the dielectric continuum approximation and Loudon＇s uniaxial crystal model. A numerical calculation of a freestanding wurtzite GaN/AlN QWR is performed. The results reveal that for a relatively large azimuthal quantum number m or wave-number kz in the free z-direction, there exist two branches of IO phonon modes localized at the interface, and only one branch of SO mode localized at the surface in the system. The degenerating behaviours of the IO and SO phonon modes in the wurtzite QWR have also been clearly observed for a small kz or m. The limiting frequency properties of the IO and SO modes for large kz and m have been explained reasonably from the mathematical and physical viewpoints. The calculations of electron-phonon coupling functions show that the high-frequency IO phonon branch and SO mode play a more important role in the electron phonon interaction.

A Study on a Wire Tension Adaptive Control System of a Multi-wire Saw in Computer Simulation

Based on the analysis of the mechanism of wire tension control by using torque motors in the multi-wire saw machining process, some mathematical models of a tension control system are studied, and an adaptive algo- rithm is designed for controlling the wire tension. In this algorithm of tension control, the rotation speeds and waving angle of motors are measured and fed back to the controller, and the NLMS（ normalized least mean squares） algorithm is used to calculate the adaptive correction value and control the wire tension accurately. The computer simulation results in Matlab software validate the high accuracy for controlling the system of the wire tension with the NLMS algorithm in the multi-wire saw machining process.

优化的CAN与1-Wire总线温度采集系统设计

针对长距离、大规模、高密度的温度场测量应用,研究了一种基于CAN总线与1-Wire总线的经济型系统解决方案。该方案以Cortex-M3处理器为核心,对CAN总线与1-Wire总线接口的硬件电路进行优化,增强了网络的稳定性。同时,从工程实际应用出发,阐述了大规模测点的优化管理与维护。该方案现已成功应用于某电厂200 MW机组的锅炉金属壁温在线检测系统,具有较好的工业应用前景。

基于1-wire总线的多主从嵌入处理器通信

介绍了ARM9 S3C2440处理器作为主控制器,通过1-wire总线和多个从处理器MSP430单片机通信的设计方案,DS2408用于主从控制器之间寻址与通信的接口器件。该系统用于北方地区暖气分户热计量改造项目,ARM9 S3C2440处理器用于每栋民用楼房的集中式热分配表的控制器,MSP430单片机用于每家户内室温控制器的微处理器。

Experimental study on spectrum and multi-scale nature of wall pressure and velocity in turbulent boundary layer

When using a miniature single sensor boundary layer probe, the time sequences of the stream-wise velocity in the turbulent boundary layer （TBL） are measured by using a hot wire anemometer. Beneath the fully developed TBL, the wall pressure fluctuations are attained by a microphone mechanism with high spatial resolution. Analysis on the statistic and spectrum properties of velocity and wall pressure reveals the relationship between the wall pressure fluctuation and the energy-containing structure in the buffer layer of the TBL. Wavelet transform shows the multi-scale natures of coherent structures contained in both signals of velocity and pressure. The most intermittent wall pressure scale is associated with the coherent structure in the buffer layer. Meanwhile the most energetic scale of velocity fluctuation at y＋ = 14 provides a specific frequency f9 ≈ 147 Hz for wall actuating control with Ret = 996.

Multi-features Based Approach for Moving Shadow Detection

In the video-based surveillance application, moving shadows can affect the correct localization and detection of moving objects. This paper aims to present a method for shadow detection and suppression used for moving visual object detection. The major novelty of the shadow suppression is the integration of several features including photometric invariant color feature, motion edge feature, and spatial feature etc. By modifying process for false shadow detected, the averaging detection rate of moving object reaches above 90% in the test of Hall-Monitor sequence.

The Large Sky Area Multi-Object Fiber Spectroscopic Telescope (LAMOST)

The Large Sky Area Multi-Object Fiber Spectroscopic Telescope (LAMOST, also called the Guo Shou Jing Telescope) is a special reflecting Schmidt telescope. LAMOST’s special design allows both a large aperture (effective aperture of 3.6 m–4.9 m) and a wide field of view (FOV) (5°). It has an innovative active reflecting Schmidt configuration which continuously changes the mirror’s surface that adjusts during the observation process and combines thin deformable mirror active optics with segmented active optics. Its primary mirror (6.67m×6.05 m) and active Schmidt mirror (5.74m×4.40 m) are both segmented, and composed of 37 and 24 hexagonal sub-mirrors respectively. By using a parallel controllable fiber positioning technique, the focal surface of 1.75 m in diameter can accommodate 4000 optical fibers. Also, LAMOST has 16 spectrographs with 32 CCD cameras. LAMOST will be the telescope with the highest rate of spectral acquisition. As a national large scientific project, the LAMOST project was formally proposed in 1996, and approved by the Chinese government in 1997. The construction started in 2001, was completed in 2008 and passed the official acceptance in June 2009. The LAMOST pilot survey was started in October 2011 and the spectroscopic survey will launch in September 2012. Up to now, LAMOST has released more than 480 000 spectra of objects. LAMOST will make an important contribution to the study of the large-scale structure of the Universe, structure and evolution of the Galaxy, and cross-identification of multiwaveband properties in celestial objects.

Design and construction of a multi-sensor position monitoring system applied to key components of synchrotron sources

High-accuracy position monitoring of key components is required for modern synchrotron sources,such as free-electron lasers and diffraction-limited storage rings.Although various position monitoring sensors have been adopted to monitor the displacement of key components in each direction in real time,these monitoring systems are usually based on their own coordinate system.Data from such systems are meaningful when evaluating and examining the data from each positioning monitoring system in a unified coordinate system.This paper presents the design and construction of a multi-sensor position monitoring system(MPMS).A hydrostatic levelling system,a wire position sensor(WPS) and a tiltmeter are fixed to a stainless steel plate that has been calibrated by a coordinate-measurement machine.Several plates form the MPMS.The system must compensate for the sag of the stretched wires so that the WPSs create a straight line.The method of the coordinate transformation from the sensor coordinate system to the MPMS coordinate system was thoroughly studied.An experimental MPMS that includes five plates was setup in a 20-m tunnel,and a validation study to verify fully the feasibility of the MPMS was performed.

Efficient direction-independent fog harvesting using a corona discharge device with a multi-electrode structure

Efflcient collection of water from fog can effectively alleviate the problem of water shortages in foggy but water-scarce areas,such as deserts,islands and so on.Unlike inefflcient fog meshes,corona discharge can charge water droplets and further enhance the water-collecting effect.This study proposes a novel multi-electrode collecting structure that can achieve efflcient and direction-independent water collection from fog.The multi-electrode structure consists of three parts:a charging electrode,an intercepting electrode and a ground electrode.Four types of watercollecting structures are compared experimentally,and the collection rates from a traditional fog mesh,a wire-mesh electrode with fog coming from a high-voltage electrode,a wire-mesh electrode with fog coming from a ground electrode and a multi-electrode structure are 2–3 g h^(-1),100–120 g h^(-1),60–80 g h^(-1)and 200–220 g h^(-1),respectively.The collection rate of the multielectrode structure is 100–150 times that of a traditional fog mesh and 2–4 times that of a wiremesh electrode.These results demonstrate the superiority of the multi-electrode structure in fog collection.In addition,the motion equation of charged droplets in an electric fleld is also derived,and the optimization strategy of electrode spacing is also discussed.This structure can be applied not only to fog collection,but also to air puriflcation,factory waste gas treatment and other flelds.

A Comparative Study of Acute Hemodynamic Effects of Multi -site Cardiac Pacing in patients with cardiac function NYHA class ⅠtoⅡ without bundle branch block

Objective To compare the acute hemodynamic effects of five different pacing modes in patients with cardiac function NYHA class Ⅰ to Ⅱ without bundle branch block (BBB). Methods This study included 12 patients (SSS 7, Ⅲ°AVB 5) undergoing pacemaker implantation. Right ventricular apex (RVA), right ventricular outflow tract (RVOT), right ventricular bifocal (RV-Bi), left ventricular base (LVB) and bi -ventricular (Bi-Ⅴ) pacing at 60 -80 ppm were done in VVI mode prior to implantation of DDD pacemaker. The cardiac index (CI), mean pulmonary artery pressure (mPAP) and pulmonary capillary wedge pressure (PCWP) were measured with Swan - Ganz thermodilution catheter after 5 minutes of each pacing mode. Results (1) Comparing to pacing at RVA (CI: 2. 41± 0. 38 L/min per m2, PCWP: 16. 7 ±3.3 mmHg), the CI increased and the PCWP decreased significantly in pacing at RVOT(CI: 2. 63 ± 0.46, PCWP: 13. 8±2. 3), LVB(CI: 2. 78±0.52, PCWP: 14. 4±3.1), RV-Bi(CI: 2. 83±0.57, PCWP: 12. 8± 2. 5) and Bi -Ⅴ pacing (CI: 2. 94± 0.60, PCWP: 12. 7±2. 5), P < 0. 01, respectively. (2) The CI of RV-Bi and Bi-Ⅴ pacing was higher than that of RVOT and LVB pacing, the PCWP was lower, P < 0. 05, respectively. (3) There was no significant difference between RV - Bi pacing and Bi-Ⅴ pacing in CI and PCWP. Conclusion There is no significant difference between RV - Bi pacing and Bi -V pacing in the acute hemodynamic effects; however,dual - site pacing is much better than single site pacing in that aspect for patients with cardiac function NYHA class Ⅰ to Ⅱ without BBB. Among single site pacing, the RVOT and LVB pacing is better than RVA pacing in cardiac function.

Research on A Master - slave Multi - microcomputers Control System for Hollow Spindle Fancy Yarn Spinning Machine

In this paper, a successfully studied and developed master - slave muld - microcomputers control system based on PC - BUS for hollow spindle fancy yarn spinning machine, mainly Its overall scheme, software and hardware construction, is introduced. Spinning experiments show that the system achieves satisfactory result. This system can solve the diftkultles of mechatronical fusion between domestic hollow splndk fancy yarn spuming muchine and its microcomputer control technology.

On the Representation of Multi-layer Woven Structure

A quantitative method is developed to identify the structures of multi-layer woven fabric in this study. Six structural parameters are selected to represent the fabric structure. With some design criteria for the reinforcement of textile composites, the relationships among the structural parameters are derived for different binding patterns of the fabric structure. The conditions, which meet the requirements of structural cell stability,are also discussed.

Computer-aided Pattern Design of Multi-bar Warp Knitted Fabrics

To meet the development trend of multi-bar warp knit-ting machine towards high-speed,advanced technologyand computer control and the requirements of variousproducts with small quantity,there are many researcheson the computer-aided pattern design of multi-barwarp knitted fabrics.In terms of the special propertiesof the computer-aided pattern design of multi-barwarp knitted fabrics,the Object Oriented Program(OOP)programming-Object Windows class Library(OWL)programming is selected.According to thecharacters of the OWL programming,various functionsare defined.Pattern design and technical parameters canbe output,which offers a great convenience for the fac-tory.

15×K6-EPIWRC多层阻旋转抗冲击钢丝绳研制

多层压实股钢丝绳阻旋转性能在一些应用场合有极其重要的意义,钢丝绳旋转超过相关要求会影响工作效率,甚至产生安全事故。为最大限度地克服阻旋转性差、断芯、外层磨损超标3大难题,新产品采用1-4+4/15结构形式,对绳芯进行注塑处理,以满足客户要求。26.0 mm钢丝绳研制完成后,实际破断拉力达到681.0 kN,钢丝绳各项指标均达到客户标准和EN12385标准要求,工艺设计合理,绳捻制紧密,抗旋转性能优良,抗冲击载荷性能好。

MODS： A Novel Metaheuristic of Deterministic Swapping for the Multi-Objective Optimization of Combinatorials Problems

This paper states a new metaheuristic based on Deterministic Finite Automata （DFA） for the multi - objective optimization of combinatorial problems. First, a new DFA named Multi - Objective Deterministic Finite Automata （MDFA） is defined. MDFA allows the representation of the feasible solutions space of combinatorial problems. Second, it is defined and implemented a metaheuritic based on MDFA theory. It is named Metaheuristic of Deterministic Swapping （MODS）. MODS is a local search strategy that works using a MDFA. Due to this, MODS never take into account unfeasible solutions. Hence, it is not necessary to verify the problem constraints for a new solution found. Lastly, MODS is tested using well know instances of the Bi-Objective Traveling Salesman Problem （TSP） from TSPLIB. Its results were compared with eight Ant Colony inspired algorithms and two Genetic algorithms taken from the specialized literature. The comparison was made using metrics such as Spacing, Generational Distance, Inverse Generational Distance and No-Dominated Generation Vectors. In every case, the MODS results on the metrics were always better and in some of those cases, the superiority was 100%.

DK7732-1 Electric Spark CNC Wire-Cuffing Machine

The machine tool is one of the new products developed and produced by the Shanghai No.8 Machine Tool Plant. It adopts a lift adjustable wiretrame and molybdenum filament tensioning mechanism with large cutting thickness and high machining precision. It is equipped with an advanced IBM-PC 386 microcomputer-controlled system, with strong performance and CRT display. Man/

多丝切割的“滚-刻-削”混合加工机理

当前多丝切割的环境并非理想,加工要求并非相同.而理想及单一的"滚-刻"切割加工模型对整个过程难以解释周全.基于多丝切割中磨粒运行存在多种状态,指出研磨粒的综合力学行为(研磨粒的加工机理)取决于研磨液膜的流体力学条件,处于半接触和全接触状态下的磨粒,各自以"滚-刻"、"滚-刻-削"方式实施切割加工.故多模型混合加工可以较好地解释多丝切割加工的整个过程,多模型的混合加工模式更加接近实际状况.

DXQ-601型多线切割机关键技术研究

从SiC颗粒受力情况入手,建立理论模型,根据多线切割机锯切机理,分析了切削变形分力和摩擦力引起的锯切力以及锯切力与工件的厚度、工件进给速度、锯丝的锯切速度、工件材料的性质等的关系,为多线切割机研制提供理论依据。

载流导线间轴向运动导电梁的参数-主共振

研究轴向运动导电梁在载流导线产生的周期变化磁场中的参数-主共振问题。给出载流导线间导电梁处的磁感应强度、梁的应变能、动能及所受电磁力表达式,推得轴向运动导电梁的磁弹性横向振动微分方程。应用伽辽金积分法,得到导电梁无量纲化的非线性参数-主共振微分方程。利用多尺度法求解方程,得到系统关于非线性参数-主共振联合方程的近似解析解。通过计算,得到了轴向运动导电梁共振幅值随调谐参数变化的幅频图,共振系统的动相平面轨迹图,以及在变化调谐参数下的时程图和相图。结果表明,相关参数的改变对系统的共振幅值及稳定性影响明显。