The adsorption method has the advantages of low cost,high efficiency,and environmental friendliness in treating fluorinated wastewater,and the adsorbent material is the key.This study combines the inherent anion-excha...The adsorption method has the advantages of low cost,high efficiency,and environmental friendliness in treating fluorinated wastewater,and the adsorbent material is the key.This study combines the inherent anion-exchange adsorption properties of layered double hydroxides(LDHs).Self-supported porous adsorbent materials loaded with AFm and AFt were prepared from a composite cementitious system consisting of calcium aluminate cement(CAC)and flue gas desulfurization gypsum(FGDG)by chemical foaming technique.The mineral composition of the adsorbent material was characterized by X-ray diffraction(XRD)and Scanning electron microscopy(SEM).Through the static adsorption experiment,the adsorption effect of the mineral composition of the adsorbent on fluoride ions was deeply analyzed,and the adsorption mechanism was revealed.XRD and SEM showed that the main hydration phases of the composite cementitious system consisting of CAC and FGDG are AFm,AFt,AH_(3),and CaSO_(4)·2H_(2)O.FGDG accelerates the hydration process of CAC and inhibits the transformation of AFt to AFm.The AFt content increased,and the AFm content decreased or even disappeared as the amount of FGDG increased.Static adsorption experiment results showed that AFm and AFt in adsorbent materials could significantly enhance the adsorption of fluoride ions.The adsorption of F^(−)in aqueous solution by PAG tends more towards monolayer adsorption with a theoretical maximum capacity of 108.70 mg/g and is similar to the measured value of 112.77 mg/g.展开更多
The microstructural study was conducted on cement and cement-slag pastes immersed in different concentrations of Mg（NO3）2 solutions utilizing ^29Si, ^27Al NMR spectroscopy and XRD techniques. The results show that t...The microstructural study was conducted on cement and cement-slag pastes immersed in different concentrations of Mg（NO3）2 solutions utilizing ^29Si, ^27Al NMR spectroscopy and XRD techniques. The results show that the hydration of both the cement and cement-slag pastes is delayed when the pastes are cured in Mg（NO3）2 solutions as compared to the pastes cured in water. Moreover, Mg^2＋ ions also exhibit an decalcifying and dealuminizing effect on the C-A-S-H in cement and cement-slag pastes, and thereby decrease Ca/Si and Al[4]/Si ratios of the C-A-S-H. The dealuminization of C-A-S-H is mitigated for cement-slag paste as compared to pure cement paste. The depolymerized calcium and aluminum ions from C-A-S-H gel mainly enter the pore solution to maintain the pH value and form Al^[6] in TAH, respectively. On the other hand, Mg^2＋ ions exert an impact on the intra-transition between Al^[6] species, from AFm and hydrogarnet to hydrotalcite-like phase. NO3^-ions are interstratified in the layered Mg-Al structure and formed nitrated hydrotalcite-like phase（Mg1-xAlx（OH）2（NO3）x·nH2O）. Results from both ^27Al NMR and XRD data show that ettringite seems not to react with Mg^2＋ ions.展开更多
After 32CrMoV is selected to manufacture nitrided gears coated with TiN by multi-arc ion plating, all of these uncoated gears and coated gears run in the gearbox under the same initial conditions so as to compare thei...After 32CrMoV is selected to manufacture nitrided gears coated with TiN by multi-arc ion plating, all of these uncoated gears and coated gears run in the gearbox under the same initial conditions so as to compare their difference concerning properties and microstructure. Experiment results indicate that tooth surface of the coated-TiN gears does not suffer surface abnormalities in meshed zone. Instead, the gears with nitrided case exhibit an abrasion mark on the meshed zone of tooth surface, which results in more weight loss of nitrided gears. The morphology of the surface suggests TiN film with more than 2 000 HV is so dense and smooth that coated-TiN gears have higher wear resistance compared with the uncoated gears. The microstructure of coated-TiN gears is finer, hardness is higher and its distribution of coated-TiN gears is more reliable than uncoated ones, which makes nitride layer combined with TiN film tightly. Consequently, the wear-resistance of gears has been dramatically promoted.展开更多
The early hydration of calcium aluminate cement (CAC) with different kinds of zinc (II),such as ZnSO4g7H2O,ZnO,Zn(NO3)2·6H2O and ZnCl2,was analyzed.Changes in consistency,setting time,hydration heat flow,hydratio...The early hydration of calcium aluminate cement (CAC) with different kinds of zinc (II),such as ZnSO4g7H2O,ZnO,Zn(NO3)2·6H2O and ZnCl2,was analyzed.Changes in consistency,setting time,hydration heat flow,hydration heat amount,ion concentration in solution,and hydration products were found upon the addition of different Zn^2+.The water consumption of standard consistency of CAC is decreased with different Zn^2+.Zn^2+ can delay the initial hydration of CAC.The induction period of cement with Zn^2+ is longer than that of CAC,especially the reaction time of the acceleration period is extended.Zn^2+ can promote hydration hydrate of CAC at 24 h.The characteristic diffraction peaks of CA and CA2 in CAC with different Zn^2+ are significantly reduced.It can inhibit the formation of CAH10 and promote the formation C3AH6 and AH3 in hydration products at 24 h.展开更多
CrTiAIN coatings were prepared by using a home-made industrial scale multi-arc ion plating system. The coatings were found to be composites of face-center-cubic CrN and TiN. The surface roughness, microhardness, and t...CrTiAIN coatings were prepared by using a home-made industrial scale multi-arc ion plating system. The coatings were found to be composites of face-center-cubic CrN and TiN. The surface roughness, microhardness, and tribological properties of the films were significantly affected by the nitrogen pressure and dc-pulsed bias voltage applied to the substrate. The CrTiA1N coatings with the smoothest surfaces were obtained at optimum conditions of nitrogen pressure of 5.0 Pa and bias voltage of -200 V. The samples were found to exhibit a hardness of 2900 HV0.05 with an average friction coefficient of 0.16 and wear rate of 1.5× 10^-16 m^3/N.m against cemented carbide.展开更多
The UV spectra of sodium aluminate solutions were obtained in the sodium oxide concentration range from 59 to 409 g/L and the caustic ratio range from 1.5 to 4.0 to reveal the structure characteristics of them. It is ...The UV spectra of sodium aluminate solutions were obtained in the sodium oxide concentration range from 59 to 409 g/L and the caustic ratio range from 1.5 to 4.0 to reveal the structure characteristics of them. It is found that a new peak appears at about 370 nm besides peaks at about 220 and 266 nm in all solutions. The new peak is strongly favored by high hydroxide concentration and high caustic ratio. And it only appears when the solutions are prepared by dissolving sodium hydroxide and aluminum hydroxide. In addition, the IR and Raman spectra of sodium aluminate solutions with high alkali concentration and high caustic ratio were measured, and the UV spectra of aqueous solutions of Al( H2O )36+and AlF 36?were measured as well. According to the crystal field theory in coordination chemistry as well as the above spectra characteristics, this new peak at about 370 nm is determined as the evidence of a new species of aluminate ion with a coordination number of 6.展开更多
The preparation of Al(OH)3 by the ion exchange membrane electrolysis followed by the precipitation of sodium aluminate solution with seeds was made. During the process of ion membrane electrolysis, the sodium aluminat...The preparation of Al(OH)3 by the ion exchange membrane electrolysis followed by the precipitation of sodium aluminate solution with seeds was made. During the process of ion membrane electrolysis, the sodium aluminate solution is rapidly acidified and the caustic ratio (aK) is decreased due to oxygen evolution in the anodic region. And the causticity of solution is increased due to hydrogen evolution in the cathode region, producing the high concentration of caustic soda solution. Regulating the acidity of the anodic solution by controlling the electric quantity in the electrolysis and subsequent decomposing the solution, Al(OH)3 could yield with very large rate and high efficiency. The experiments also indicate that the quality of aluminum hydroxide product is greatly affected by the impurity silicon.展开更多
The multi-arc ion plating technology was employed to prepare the molybdenum films with thickness of 3 μm on the AISI 1045 steel. The wear and scuffing tests were carried out on the ball-on-disc tester. AFM and SEM eq...The multi-arc ion plating technology was employed to prepare the molybdenum films with thickness of 3 μm on the AISI 1045 steel. The wear and scuffing tests were carried out on the ball-on-disc tester. AFM and SEM equipped with EDS were adopted to observe and analyze the morphologies and element compositions of surface,cross-section and worn scar of the Mo film. The phase structure was studied by XRD and the bonding strength between Mo film and substrate was measured by scratching tester. The tribological experiments show that the Mo film possesses a good wear-resistance and an excellent anti-scuffing property. The failure mechanism of Mo film under extreme condition is flaking off.展开更多
This paper presents the formation of Cr-O thin films on an iron substrate by multi-arc ion plating, which are intended to be used as a thermal radiation absorbent in electronic vacuum devices. Only oxygen was used as ...This paper presents the formation of Cr-O thin films on an iron substrate by multi-arc ion plating, which are intended to be used as a thermal radiation absorbent in electronic vacuum devices. Only oxygen was used as a reaction gas during deposition, the Cr-O thin film, must have high adhesion and low outgassing rate. The scratch test shows that the critical load, for an applicable Cr-O thin film deposited in oxygen atmosphere alone at a pressure of 8×10<sup>-1</sup> Pa, was as high as 6kg.展开更多
During the precipitation of gibbsite from supersaturated sodium aluminate solution, the main aluminum containing species in solution will transform from tetrahedral [Al(OH) 4] - to sixfold octahedral [(H 2O) 2Al (OH) ...During the precipitation of gibbsite from supersaturated sodium aluminate solution, the main aluminum containing species in solution will transform from tetrahedral [Al(OH) 4] - to sixfold octahedral [(H 2O) 2Al (OH) 4] -. In order to elucidate the mechanisms responsible for above transformation, the formation Gibbs free energy as well as frontier orbits of a wide range of aluminum species are studied by ab initio method at B3LYP/6 31G** level. Based on theoretical calculation results, thermodynamic possibility and coordination possibility for aluminate ion transforming from [Al(OH) 4] - to [(H 2O) 2Al(OH) 4] - are analyzed and thermodynamic permitted reaction pathways are extracted. It is found that [Al(OH) 4] - can not react directly with H 2O to carry out the variation of coordination number. Transformation of tetrahedral [Al(OH) 4] - to octahedral [(H 2O) 2Al(OH) 4] - is involved in two reaction pathways, one is realized by neutral [Na(H 2O) + 4·Al(OH) - 4] acting mediator, the other is carried by neutral [(H 2O)Al(OH) 3]. Though there is a strong thermodynamic trend for the transformation of [Al(OH) 4] - to [(H 2O) 2Al(OH) 4] -, the practical transformation is very slow. Thus, it can be concluded that there is a great kinetic resistance during the transformation from [Al(OH) 4] - to [(H 2O) 2Al(OH) 4] -.展开更多
The roles of different point defects in persistent luminescence of SrAl2O4：Eu,Dy phosphors were investigated. The research results showed that Dyer plays an important role in the persistent luminescence of SrA1EO4：E...The roles of different point defects in persistent luminescence of SrAl2O4：Eu,Dy phosphors were investigated. The research results showed that Dyer plays an important role in the persistent luminescence of SrA1EO4：Eu, Dy phosphors. It can serve as the electron trap of suitable depth for persistent luminescence. V~ does not serve as the electron trap of suitable depth, but its existence can increase the depth of electron traps. There is interaction between the Dy^3＋（ DySr ） and the Eu^2＋（Eu^x Sr ）, and only if the distance between the Dy^3＋（DySr） and the Eu^2＋ （Eu^x Sr） is close enough, the Dyer can work as an effective electron trap. The point defect of V＂ Sr can be hole trap, but the change of its density in crystal matrix does not arouse the obvious change of persistent luminescence.展开更多
基金supported by the National Natural Science Foundation of China(No.52279138)supported by Scientific Research Project of Shanxi Province(2018SF-367).
文摘The adsorption method has the advantages of low cost,high efficiency,and environmental friendliness in treating fluorinated wastewater,and the adsorbent material is the key.This study combines the inherent anion-exchange adsorption properties of layered double hydroxides(LDHs).Self-supported porous adsorbent materials loaded with AFm and AFt were prepared from a composite cementitious system consisting of calcium aluminate cement(CAC)and flue gas desulfurization gypsum(FGDG)by chemical foaming technique.The mineral composition of the adsorbent material was characterized by X-ray diffraction(XRD)and Scanning electron microscopy(SEM).Through the static adsorption experiment,the adsorption effect of the mineral composition of the adsorbent on fluoride ions was deeply analyzed,and the adsorption mechanism was revealed.XRD and SEM showed that the main hydration phases of the composite cementitious system consisting of CAC and FGDG are AFm,AFt,AH_(3),and CaSO_(4)·2H_(2)O.FGDG accelerates the hydration process of CAC and inhibits the transformation of AFt to AFm.The AFt content increased,and the AFm content decreased or even disappeared as the amount of FGDG increased.Static adsorption experiment results showed that AFm and AFt in adsorbent materials could significantly enhance the adsorption of fluoride ions.The adsorption of F^(−)in aqueous solution by PAG tends more towards monolayer adsorption with a theoretical maximum capacity of 108.70 mg/g and is similar to the measured value of 112.77 mg/g.
基金Funded by National Natural Science Foundation of China(Nos.51778513,51402003,51578004)China Ministry of Science and Technology(No.2015CB655101)
文摘The microstructural study was conducted on cement and cement-slag pastes immersed in different concentrations of Mg（NO3）2 solutions utilizing ^29Si, ^27Al NMR spectroscopy and XRD techniques. The results show that the hydration of both the cement and cement-slag pastes is delayed when the pastes are cured in Mg（NO3）2 solutions as compared to the pastes cured in water. Moreover, Mg^2＋ ions also exhibit an decalcifying and dealuminizing effect on the C-A-S-H in cement and cement-slag pastes, and thereby decrease Ca/Si and Al[4]/Si ratios of the C-A-S-H. The dealuminization of C-A-S-H is mitigated for cement-slag paste as compared to pure cement paste. The depolymerized calcium and aluminum ions from C-A-S-H gel mainly enter the pore solution to maintain the pH value and form Al^[6] in TAH, respectively. On the other hand, Mg^2＋ ions exert an impact on the intra-transition between Al^[6] species, from AFm and hydrogarnet to hydrotalcite-like phase. NO3^-ions are interstratified in the layered Mg-Al structure and formed nitrated hydrotalcite-like phase（Mg1-xAlx（OH）2（NO3）x·nH2O）. Results from both ^27Al NMR and XRD data show that ettringite seems not to react with Mg^2＋ ions.
基金This project is supported by National Natural Science Foundation of China(No.50375164)Visitor Scholar Project of State Key Laboratory of Mechanical Transmission in Chongqing University,China.
文摘After 32CrMoV is selected to manufacture nitrided gears coated with TiN by multi-arc ion plating, all of these uncoated gears and coated gears run in the gearbox under the same initial conditions so as to compare their difference concerning properties and microstructure. Experiment results indicate that tooth surface of the coated-TiN gears does not suffer surface abnormalities in meshed zone. Instead, the gears with nitrided case exhibit an abrasion mark on the meshed zone of tooth surface, which results in more weight loss of nitrided gears. The morphology of the surface suggests TiN film with more than 2 000 HV is so dense and smooth that coated-TiN gears have higher wear resistance compared with the uncoated gears. The microstructure of coated-TiN gears is finer, hardness is higher and its distribution of coated-TiN gears is more reliable than uncoated ones, which makes nitride layer combined with TiN film tightly. Consequently, the wear-resistance of gears has been dramatically promoted.
基金Funded by National Natural Science Foundation of China(No.51802235)State Key Laboratory of Silicate Materials for ArchitecturesWuhan University of Technology(No.SYSJJ2015-07)。
文摘The early hydration of calcium aluminate cement (CAC) with different kinds of zinc (II),such as ZnSO4g7H2O,ZnO,Zn(NO3)2·6H2O and ZnCl2,was analyzed.Changes in consistency,setting time,hydration heat flow,hydration heat amount,ion concentration in solution,and hydration products were found upon the addition of different Zn^2+.The water consumption of standard consistency of CAC is decreased with different Zn^2+.Zn^2+ can delay the initial hydration of CAC.The induction period of cement with Zn^2+ is longer than that of CAC,especially the reaction time of the acceleration period is extended.Zn^2+ can promote hydration hydrate of CAC at 24 h.The characteristic diffraction peaks of CA and CA2 in CAC with different Zn^2+ are significantly reduced.It can inhibit the formation of CAH10 and promote the formation C3AH6 and AH3 in hydration products at 24 h.
基金supported by the China Ministry of Industry and Information Technology (No. 2009ZX04012-032)Basic Research Fund of Central Universities
文摘CrTiAIN coatings were prepared by using a home-made industrial scale multi-arc ion plating system. The coatings were found to be composites of face-center-cubic CrN and TiN. The surface roughness, microhardness, and tribological properties of the films were significantly affected by the nitrogen pressure and dc-pulsed bias voltage applied to the substrate. The CrTiA1N coatings with the smoothest surfaces were obtained at optimum conditions of nitrogen pressure of 5.0 Pa and bias voltage of -200 V. The samples were found to exhibit a hardness of 2900 HV0.05 with an average friction coefficient of 0.16 and wear rate of 1.5× 10^-16 m^3/N.m against cemented carbide.
基金Project(50234040) supported by the Key Project of the National Natural Science Foundation of ChinaProject(2005AA647010) supported by the National High-Tech Research and Development Program of China
文摘The UV spectra of sodium aluminate solutions were obtained in the sodium oxide concentration range from 59 to 409 g/L and the caustic ratio range from 1.5 to 4.0 to reveal the structure characteristics of them. It is found that a new peak appears at about 370 nm besides peaks at about 220 and 266 nm in all solutions. The new peak is strongly favored by high hydroxide concentration and high caustic ratio. And it only appears when the solutions are prepared by dissolving sodium hydroxide and aluminum hydroxide. In addition, the IR and Raman spectra of sodium aluminate solutions with high alkali concentration and high caustic ratio were measured, and the UV spectra of aqueous solutions of Al( H2O )36+and AlF 36?were measured as well. According to the crystal field theory in coordination chemistry as well as the above spectra characteristics, this new peak at about 370 nm is determined as the evidence of a new species of aluminate ion with a coordination number of 6.
基金Project(2005CB623702) supported by the National Basic Research Program of China
文摘The preparation of Al(OH)3 by the ion exchange membrane electrolysis followed by the precipitation of sodium aluminate solution with seeds was made. During the process of ion membrane electrolysis, the sodium aluminate solution is rapidly acidified and the caustic ratio (aK) is decreased due to oxygen evolution in the anodic region. And the causticity of solution is increased due to hydrogen evolution in the cathode region, producing the high concentration of caustic soda solution. Regulating the acidity of the anodic solution by controlling the electric quantity in the electrolysis and subsequent decomposing the solution, Al(OH)3 could yield with very large rate and high efficiency. The experiments also indicate that the quality of aluminum hydroxide product is greatly affected by the impurity silicon.
基金Project(50235030) supported by the National Natural Science Foundation of China Project(G1999065009) supported by the National Basic Research Program of China Project(2003AA331130) supported by the Hi-tech Research and Development Program of China
文摘The multi-arc ion plating technology was employed to prepare the molybdenum films with thickness of 3 μm on the AISI 1045 steel. The wear and scuffing tests were carried out on the ball-on-disc tester. AFM and SEM equipped with EDS were adopted to observe and analyze the morphologies and element compositions of surface,cross-section and worn scar of the Mo film. The phase structure was studied by XRD and the bonding strength between Mo film and substrate was measured by scratching tester. The tribological experiments show that the Mo film possesses a good wear-resistance and an excellent anti-scuffing property. The failure mechanism of Mo film under extreme condition is flaking off.
文摘This paper presents the formation of Cr-O thin films on an iron substrate by multi-arc ion plating, which are intended to be used as a thermal radiation absorbent in electronic vacuum devices. Only oxygen was used as a reaction gas during deposition, the Cr-O thin film, must have high adhesion and low outgassing rate. The scratch test shows that the critical load, for an applicable Cr-O thin film deposited in oxygen atmosphere alone at a pressure of 8×10<sup>-1</sup> Pa, was as high as 6kg.
文摘During the precipitation of gibbsite from supersaturated sodium aluminate solution, the main aluminum containing species in solution will transform from tetrahedral [Al(OH) 4] - to sixfold octahedral [(H 2O) 2Al (OH) 4] -. In order to elucidate the mechanisms responsible for above transformation, the formation Gibbs free energy as well as frontier orbits of a wide range of aluminum species are studied by ab initio method at B3LYP/6 31G** level. Based on theoretical calculation results, thermodynamic possibility and coordination possibility for aluminate ion transforming from [Al(OH) 4] - to [(H 2O) 2Al(OH) 4] - are analyzed and thermodynamic permitted reaction pathways are extracted. It is found that [Al(OH) 4] - can not react directly with H 2O to carry out the variation of coordination number. Transformation of tetrahedral [Al(OH) 4] - to octahedral [(H 2O) 2Al(OH) 4] - is involved in two reaction pathways, one is realized by neutral [Na(H 2O) + 4·Al(OH) - 4] acting mediator, the other is carried by neutral [(H 2O)Al(OH) 3]. Though there is a strong thermodynamic trend for the transformation of [Al(OH) 4] - to [(H 2O) 2Al(OH) 4] -, the practical transformation is very slow. Thus, it can be concluded that there is a great kinetic resistance during the transformation from [Al(OH) 4] - to [(H 2O) 2Al(OH) 4] -.
基金This study is financially supported by the Jiangxi University of Finance and Economy (Project No. 0421205) Jiangxi Provincial Department of Education (Project No. (2007) 260)
文摘The roles of different point defects in persistent luminescence of SrAl2O4：Eu,Dy phosphors were investigated. The research results showed that Dyer plays an important role in the persistent luminescence of SrA1EO4：Eu, Dy phosphors. It can serve as the electron trap of suitable depth for persistent luminescence. V~ does not serve as the electron trap of suitable depth, but its existence can increase the depth of electron traps. There is interaction between the Dy^3＋（ DySr ） and the Eu^2＋（Eu^x Sr ）, and only if the distance between the Dy^3＋（DySr） and the Eu^2＋ （Eu^x Sr） is close enough, the Dyer can work as an effective electron trap. The point defect of V＂ Sr can be hole trap, but the change of its density in crystal matrix does not arouse the obvious change of persistent luminescence.
