Evaluation of the Oxidation Reactivity and Behavior of Exhaust Soot Particles from Diesel Engines with Different Emission Levels

The aim of this study was to investigate the oxidation reactivity and behavior of exhaust particulate matter(PM)from diesel engines.PM samples from two diesel engines(1K,CY4102)with different emission levels were collected by a thermophoretic system and a quartz filter.The oxidation reactivity,oxidation behaviors,and physicochemical properties of the PM samples were analyzed using thermogravimetric analysis(TGA),high-resolution transmission electron microscopy(HRTEM),Fourier-transform infrared spectrometry(FTIR),and Raman spectroscopy.The results showed that there was a great difference in the oxidation reactivity of soot particles emitted by the two different diesel engines.A qualitative analysis of the factors influencing oxidation reactivity showed that the nanostructure,degree of graphitization,and relative concentration of aliphatic C—H functional groups were the most important factors,whereas no significant correlation was found between the primary particle size and activation energy of the diesel soot.Based on the oxidation behavior analysis,the diesel soot particles exhibited both internal and surface oxidation modes during the oxidation process.Surface oxidation was dominant during the initial stage,and as oxidation progressed,the mode gradually changed to internal oxidation.Internal oxidation mode of soot particles from the 1K engine was significantly higher than that of CY4102.

Performance, Combustion and Emission Characteristics of Oxygenated Diesel in DI Engines: A Critical Review

The transition from non-renewable to renewable energy sources is a significant challenge of our time. In the fuel industry, oxygenated additives such as butanol are transforming conventional fuels into renewable biofuels. This technology has been utilized in reciprocating engines for decades. This paper reviews the viability of using an n-butanol blend as a short-term replacement for diesel by analyzing its physical and chemical properties, combustion, performance, and emission characteristics in compression ignition (CI) engines under various conditions, including variable load, speed, acceleration, and both stationary and transient cycles. N-Butanol exhibits higher viscosity, better lubricity, higher heating value, improved blend stability, enhanced cold-flow properties, and higher density. These factors influence spray formation, injection timing, atomization, and combustion characteristics. Its higher oxygen content improves the diffusion combustion stage and efficiency. Adding 5% and 10% n-butanol to diesel increases pressure and apparent heat release rate, slightly reduces temperature, and improves thermal efficiency, with mixed effects on CO and THC emissions and a notable decrease in particulate matter emissions. Fuel consumption increases, while the impact on NOx emissions varies. A 10% butanol blend is considered optimal for enhancing performance and reducing particulate emissions without significantly affecting NOx emissions. Blending up to 40% butanol with diesel does not require engine modifications or ECU recalibrations in engines calibrated for pure diesel. Due to its advantageous properties and performance, n-butanol is recommended as a superior alcohol-diesel blend than ethanol for short-term diesel replacement.

Detecting Power Imbalance in Multi-Cylinder Inline Diesel Engine Genset

A model of fuel injection adjustment for balancing the 4-stroke six cylinder diesel engine coupling geneset is developed by detecting imbalance in operating engine by the frequency analysis of the crankshaft＇s speed variation. In this work, the crankshaft is considered to be a rigid body, so that the variation of its angular speed could be directly correlated to the total gas-pressure torque. By analyzing only the lower harmonic orders, the speed variation spectrum can filter out the distortions produced by the dynamic response of the crankshaft. The information carried by these harmonic orders permits to establish correlations between measurements and the average gas pressure torque of the engine, and to detect imbalance and identify faulty cylinders. Detailed experimental reading are taken on diesel engine coupling genset on the test bed of Greaves Cotton Ltd Pane, India.

Coupling problem between the dynamical and tribological behaviors in the piston-liner systems of multi-cylinder IC engines

This paper deals with the coupling problem between the dynamic behaviors and the tribological behaviors of the piston-liner systems in multi-cylinder internal combustion engines. Firstly, based on the correction of some errors in the equation of piston secondary motion, which have been employed by many authors for several years, a detailed mathematical model for the coupling problem between the dynamical and tribological behaviors in the piston-liner systems of multi-cylinder internal combustion engines is presented. Secondly, the lubrication and friction between the liner and piston in each cylinder is included applying the average flow model of the Reynolds equation. Thirdly, the vibration of each liner is computed through the finite element model of a four-cylinder engine block, by which not only the liner motions caused by the block vibration but also the local vibration and the local static deformation of each liner can be figured out and taken into account. Through theoretical analysis and computation, some conclusions can be drawn as: 1) Both the liner vibration and piston motion are different for different cylinder in a multi-cylinder internal combustion engine, and hence different piston-liner systems will have different tribological behaviors. 2) Different liners have coincident dynamic response on the whole, especially for the lower frequency components. However, differences still exist among the vibrations of different liners, and these differences are mainly owing to the higher frequency components. 3) The impacts of liner vibrations on the tribological behaviors in piston-liner systems are primarily ascribed to its higher frequency components.

Optimization of the Performance of Marine Diesel Engines to Minimize the Formation of SO_x Emissions

Optimization procedures are required to minimize the amount of fuel consumption and exhaust emissions from marine engines.This study discusses the procedures to optimize the performance of any marine engine implemented in a 0D/1D numerical model in order to achieve lower values of exhaust emissions.From that point,an extension of previous simulation researches is presented to calculate the amount of SOx emissions from two marine diesel engines along their load diagrams based on the percentage of sulfur in the marine fuel used.The variations of SOx emissions are computed in g/k W·h and in parts per million(ppm)as functions of the optimized parameters:brake specific fuel consumption and the amount of air-fuel ratio respectively.Then,a surrogate model-based response surface methodology is used to generate polynomial equations to estimate the amount of SOx emissions as functions of engine speed and load.These developed non-dimensional equations can be further used directly to assess the value of SOx emissions for different percentages of sulfur of the selected or similar engines to be used in different marine applications.

HC-PM COUPLING MODEL FOR PARTICULATE MATTER EMISSION OF DIESEL ENGINES

A rapid, phenomenological model that predicts paniculate matter (PM) emissionof diesel engines is developed and formulated. The model is a chemical equilibrium compositionmodel, and is based on the formation mechanisms of PM and unburned hydrocarbon (HC) emissions ofdiesel engines. It can evaluate the emission concentration of PM via the emission concentration ofHC. To validate the model, experiments are carried out in two research diesel engines. Comparisonsof the model results with the experimental data show good agreement. The model can be used toevaluate the concentration of PM emission of diesel engines under lack of PM measuring instruments.In addition, the model is useful for computer simulations of diesel engines, as well as electroniccontrol unit (ECU) designs for electronically controlled diesel engines.

Hardware-in-the-Loop Research on the Electronic Control Unit for Diesel Engines

A hardware-in-the-loop simulating platform is developed to avoid designing defects caused by the complicated logical structure and multiple-functional buildup of the dectronic control unit（ECU）in modem diesel engines, and to diminish potential damages on components or human exposure to dangers in R＆D en- deavor. This plat-form consists of a computer installed with software Matlab/Simulink/RTW and dSPACE/ ControlDesk; a diesel engine ECU, and a dSPACE autobox which runs a real-time diesel engine model. A typical model of diesel engine with turbocharger and intercooler is presented. Based on this model our research is carried out with a real ECU to test its software control strategies. Results show that by using the diesel engine model downloaded inside, the hardware-in-the-loop platform can simulate diesel engine＇s working conditions and generate all kinds of sensor signals which ECU needs on a real-time basis. So the ECU control strategies can be validated and relevant parameters roughly calibrated.

Optimal Mixture Ratios of Biodiesel Ethanol Diesel for Diesel Engines

In this paper, we study the best-mixture ratio of biodiesel-ethanol-diesel for diesel engines. The simulation results show that the integrated indexes including engine power, cost-effectiveness and emission properties are rather better with different optimizing index when the ratio of bio-diesel, ethanol and diesel are 71.58:2.72:25.70 and 50:2.4127:47.5873.

Optimizing the Exhaust System of Marine Diesel Engines to Improve Low-speed Performances and Cylinder Working Conditions

Proper design of exhaust systems in marine high-power turbocharged diesel engines can contribute to improve the low-speed performance of these engines and make the working conditions of the cylinders more uniform.Here a high-power marine 16-cylinder V-type turbocharged diesel engine is simulated using the GT-Power software.The results reveal the differences induced by different exhaust system structures,such as an 8-cylinder-inpipe exhaust system with single/double superchargers and a 4-cylinder-in-pipe exhaust system with a single supercharger.After a comparative analysis,the 8-cylinder type with double superchargers is determined to be the optimal solution,and the structure of the exhaust system is further optimized.The simulations show that the optimized maximum exhaust temperature difference among cylinders is reduced by 66%.Finally,the simulation results and the optimized performance of the designed exhaust system are verified through experiments.

Miller Cycle with Early Intake Valve Closing in Marine Medium-Speed Diesel Engines

In this study,a one-dimensional simulation was performed to evaluate the performance of in-cylinder combustion to control NO_(x) emissions on a four-stroke,six-cylinder marine medium-speed diesel engine.Reducing the combustion temperature is an important in-cylinder measure to decrease NO_(x) emissions of marine diesel engines.The Miller cycle is an effective method used to reduce the maximum combustion temperature in a cylinder and accordingly decrease NO_(x) emissions.Therefore,the authors of this study designed seven different early intake valve closing(EIVC)Miller cycles for the original engine,and analyzed the cycle effects on combustions and emissions in high-load conditions.The results indicate that the temperature in the cylinder was significantly reduced,whereas fuel consumption was almost unchanged.When the IVC was properly advanced,the ignition delay period increased and the premixed combustion accelerated,but the in-cylinder average pressure,temperature and NO_(x) emissions in the cylinder were lower than the original engine.However,closing the intake valve too early led to high fuel consumption.In addition,the NO_(x) emissions,in-cylinder temperature,and heat release rate remarkably increased.Therefore,the optimal timing of the EIVC varied with different loads.The higher the load was,the earlier the best advance angle appeared.Therefore,the Miller cycle is an effective method for in-engine NO_(x) purification and does not entail significant cost.

Assessment of the Application of Subcooled Fluid Boiling to Diesel Engines for Heat Transfer Enhancement

The increasing demand of cooling in internal combustion engines(ICE)due to engine downsizing may require a shift in the heat removal method from the traditional single phase liquid convection to the application of new technologies based on subcooled fluid boiling.Accordingly,in the present study,experiments based on subcooled flow boiling of 50/50 by volume mixture of ethylene glycol and water coolant(EG/W)in a rectangular channel heated by a cast iron block are presented.Different degrees of subcooling,velocity and pressure conditions are examined.Comparison of three empirical reference models shows that noticeable deviations occur especially when low bulk subcooling and velocity conditions are considered.On the basis of the experimental data,a modified power-type wall heat flux model is developed and its ability to represent adequately reality is tested through numerical simulations against a reference rig case and a practical diesel engine.Computational results show that this modified model can effectively be used for practical engine cooling system design.

A New Method for Computing Radiation Heat Flow of In-Cylinder Soot of Diesel Engines

A concise formula for computing radiation heat flow of in-cylinder soot is presented, based on the assumptions that in-cylinder heat transfer of diesel engines is a quasi-equilibrium process and in-cylinder soot particles are spherical. That in this formula there consist neither constants needing adjustments nor variables related to engine types or operating conditions makes it universal and easy to use. Also it can be seen from the formula that radiation heat transfer is proportional to the quotient of in-cylinder soot mass over the average radius of primary particles. Besides, with the help of different algorithms it can be used for predicting cylinders＇ global as well as local radiation heat flows. As a demonstrative application on its global facet, a three-dimension simulation study about the soot-radiation-related heat flow in the combustion chamber of a diesel engine is carried out. Results show that the range of the soot-radiation-related heat flow computed by this formula agrees well with other researcher＇s earlier theoretic reasoning and experimental measurements.

A Review and Comparison on Recent Optimization Methodologies for Diesel Engines and Diesel Power Generators

The electrical instability that frequently distinguishes the isolated networks and depends on diesel generators to supply their energy requirements leads to an operation of the diesel generator in a transient dynamic condition and/or at low loads. In addition, extended operation of the diesel generator at partial load develops the condensation of combustion residues on the engine cylinder walls, which, after a certain time, increases friction, reduces the efficiency of the equipment and increases its fuel consumption. On the other hand, recent regulatory changes have led to ever more stringent and evolving emission standards. Among these, the International Maritime Organization (IMO) and the Environmental Protection Agency (EPA) have implemented emission standards in order to reduce exhaust gas emitted by marine diesel engines. To phase lower emission engines as soon as possible, a Tier system was adopted. This paper presents a literature review of existing technologies available to optimize the energy performance of diesel engines and diesel generators in order to reduce the cost of electricity, to increase the diesel engine efficiency and to decrease their fuel consumption and greenhouse gases (GHG) emissions. The proposed optimization methodologies are based on the application of Pre-treatment, Internal treatment and Post-treatment technologies for diesel engines and on the application of mechanical and electrical technologies for diesel power generators (DPGs). The list of references given at the end of the paper should offer aids for students and researchers working in this field.

An Evaluation of Human Error Probabilities for Critical Failures in Auxiliary Systems of Marine Diesel Engines

Human error,an important factor,may lead to serious results in various operational fields.The human factor plays a critical role in the risks and hazards of the maritime industry.A ship can achieve safe navigation when all operations in the engine room are conducted vigilantly.This paper presents a systematic evaluation of 20 failures in auxiliary systems of marine diesel engines that may be caused by human error.The Cognitive Reliability Error Analysis Method(CREAM)is used to determine the potentiality of human errors in the failures implied thanks to the answers of experts.Using this method,the probabilities of human error on failures were evaluated and the critical ones were emphasized.The measures to be taken for these results will make significant contributions not only to the seafarers but also to the ship owners.

Evaluation of properties for lubricant filter in diesel engines

The properties of lubricant filters in diesel engines directly affect operation of the lubricant system, and lubricant filters are apt to be impacted by many factors. Therefore, scientific and sensible methods evaluating the properties for lubricant filter diesel engines are necessary to monitor filter properties on line and dynamically. This paper applies ferrographic techniques and adopts sampling methods that oil specimens are synchronously obtained in front of and behind filter elements to monitor the filters of ISUZU DA-220 diesel engine in two FD50 forklifts. Results show that the combination of ferrographic techniques and above sampling methods is effective in analyzing the whole operating process of filters used in diesel engines. The service life and ruined type of filter can be estimated through the relationship between ferrographic readings in front and behind of filter and operation time. Furthermore, through a great deal of tests, a series of experimental curves of readings and time and characteristic parameters for filters used in different machines can be gained, which has guiding significance to the selection and maintenance of the filters. But because of the limitation of the ferrographic technique, the debris on the substrate prevents determination of sizes. It is difficult to judge accurately the size of debris that a filter can filter.

Dynamic Characteristic Investigation on the Fuel Pressure of Diesel Engines Electronic In-line Pump System

The electronic in-line pump (EIP) is a complex system consisting of mechanical, hydraulic, and electromagnetic parts. Experimental study showed that the fuel pressure of the plunger and the fuel drainage of the pressure system after fuel injection could result in fuel pressure fluctuation in the low pressure system. Such fluctuation exhibited pulsating cycle fluctuation as the amplitude rose with the increase of the injection pulse width. The time domain analysis found that the pressure time history curve and injection cylinders corresponded with a one-to-one relationship. By frequency domain analysis, the result was that with the increase of the working cylinder number, the high frequency amplitude gradually increased and the basic frequency amplitude gradually decreased. The conclusion was that through wavelet transformation, the low pressure signal simultaneously moved towards low frequency as the high frequency of the wavelet transformation signal with the working cylinder number increased. Lastly, by using the numerical model, the study investigated the simulation research concerning the relationship of the fluctuation dynamic characteristic in the low pressure system and the fuel injection characteristic of the high pressure system, completing the conclusions obtained by the experimental study.

Detection of cylinder pressure in diesel engines using cylinder head vibration and time series methods

This paper investigates the vibration characteristics of diesel engine cylinder heads by means of the time series method. With the concept of "Assumed System",the vibration transfer function of real cylinder head structures is established using the autoregressive-moving average models(ARMA models) of cylinder head surface vibration signals. Then this transfer function is successfully used to reconstruct the gas pressure trace inside the cylinder from measured cylinder head vibration signals. This offers an effective means for diesel engine cylinder pressure detection and condition monitoring.

Research on Fault Prediction for Marine Diesel Engines

Condition-based maintenance based on fault prediction has been widely concerned by the industry. Most of the contributions on fault prediction are based on various sensor data and mathematical models of the equipment. The complexity of the model and data signal is the key factor affecting the practicability of the model. In addition, even for the same type and batch of equipment, the manufacturing process, operation environment and other factors also affect the model parameters. In this paper, a series event model is conducted to predict the fault of marine diesel engines. Numerical example illustrates that the proposed event model is feasible.

Comparative Study of Exhaust Emissions from Diesel and Syngas Powered 3.5 kW Compression Ignition Engine with and without Load

Despite diesel engines being highly efficient, with low fuel consumption and reduced carbon dioxide emissions, they emit relatively high levels of particulate matter and oxides of nitrogen (NOx) due to high exhaust gas temperatures. Engine emissions show the quality and completeness of combustion. This paper aims to present the results of a study comparing exhaust emissions from a diesel and syngas powered engine. Syngas was produced from co-firing coal and biomass in a gasifier then cleaned, cooled and applied as an alternative fuel in an engine operated from 0 - 100% load. Exhaust-emissions were monitored at this load conditions. The exhaust-temperature was measured using thermocouples and the emission gases were analyzed using Testo 350. The emissions were lower and decreased as the engine load increased, except for sulphur dioxide and NOx. The study shows that levels of carbon monoxide, were higher in a range of 46.5 - 80.2%, while carbon dioxide was 3.3 - 18% higher compared to those from diesel. Hydrocarbon emissions were 480 and 1250 ppm for diesel and syngas respectively. The study reveals that the engine operates optimally at higher loads since hydrocarbons and oxides of carbon are low due to complete combustion at higher temperatures. Exhaust gas temperature was higher in the syngas fuel and increased as the engine load increased in the range of 455.83 - 480.03˚C which influenced the formation of NOx. NOx from diesel was found to be higher, ranging from 32.5 - 40.5%, compared to those from syngas with an engine load of 75%. The study observed that relative to diesel, the emissions of sulfur dioxide at 50% engine load were lower in a range of 23.7 - 57.1%. Emissions of hydrocarbons depended on the degree of substitution of diesel and engine load. The study therefore shows that, relative to diesel, emissions decreased when syngas was used with upgraded syngas from Prosporis juliflora presenting as the best alternative followed by Hyphanae compressa, and lastly rice husk. For optimal performance of the syngas fuelled engine, the study reports that the engine should be operated at engine loads above 50% with strategies on NOx emissions considered.

Combined Effect of a Catalytic Reduction Device with Waste Frying Oil-Based Biodiesel on NOx Emissions of Diesel Engines

Internal combustion engines with application in automobiles and other relevant industries constitute significant environmental pollution via the release of toxic exhaust gasses like carbon monoxide (CO), hydrocarbons (HC), particulate matter (PM), and nitrogen oxide (NOx). Engine researchers and manufacturers are challenged to develop external and internal measures to ensure environmentally friendly solutions to accommodate and conform to the growing list of emission standards. Therefore, this work presents an experimental investigation of the NOx emission profile of a diesel engine that is fuelled and fitted with waste frying oil-based biodiesel and catalytic converter. Using a single-cylinder, four-stroke air-cooled CI engine at a constant speed of 1900 rpm and different loadings of 25%, 50%, 75%, and 100%;fitted with a catalytic converter at the exhaust outlet of the engine and linked to a dynamometer and a gas analyser, an experiment was conducted at biodiesel/diesel volume blends of B0 (0/10), B5 (5/95), B20 (20/80), B30 (30/70), B70 (70/30), B100 (100/0);and 30% concentration (v/v), 0.5 litre/hr flow rate of aqueous urea from the catalytic converter. The results show an increasing NOx emission as the biodiesel component increased in the blend. The catalytic converter showed a downward NOx reduction with a significant 68% reduction in efficiency at high exhaust gas temperatures. It is concluded that the combined utilisation of waste frying oil-based biodiesel and the catalytic converter yields substantial NOx emission reduction.