A review on current development of thermophotovoltaic technology in heat recovery

The burning of fossil fuels in industry results in significant carbon emissions,and the heat generated is often not fully utilized.For high-temperature industries,thermophotovoltaics(TPVs)is an effective method for waste heat recovery.This review covers two aspects of high-efficiency TPV systems and industrial waste heat applications.At the system level,representative results of TPV complete the systems,while selective emitters and photovoltaic cells in the last decade are compiled.The key points of components to improve the energy conversion efficiency are further analyzed,and the related micro/nano-fabrication methods are introduced.At the application level,the feasibility of TPV applications in high-temperature industries is shown from the world waste heat utilization situation.The potential of TPV in waste heat recovery and carbon neutrality is illustrated with the steel industry as an example.

Finite-Time Thermodynamic Simulation of Circulating Direct Condensation Heat Recovery on Chillers

A time series model is used in this paper to describe the progress of circulating direct condensation heat recovery of the compound condensing process (CCP) which is made of two water cooling condensing processes in series for a centrifugal chiller in the paper. A finite-time thermodynamics method is used to set up the time series simulation model. As a result, an upper bound of recoverable condensation heat for the compound condensing process is obtained which is in good agreement with experimental result. And the result is valuable and useful to optimization design of condensing heat recovery.

Observation of the Effects of Anesthesia Recovery Nursing Combined with Heat Preservation Measures in Patients Undergoing General Anesthesia Surgery

Objective:To observe the application effects of anesthesia recovery nursing with heat preservation measures in patients undergoing general anesthesia surgery.Methods:300 cases of general anesthesia surgery patients in our hospital from March 2023 to February 2024 were selected and divided into the control group and the observation group according to the random number table method,each with 150 cases.The control group adopted conventional care,while the observation group was given anesthesia recovery care and heat preservation measures on the basis of conventional care.The wake-up time,extubation time,hospitalization time,and the incidence of adverse reactions were compared between the two groups and statistically analyzed.Results:The wake-up time of patients in the control group was 9.71±1.20 hours,and that of the observation group was 6.51±1.02 hours,with statistically significant differences(P<0.05);the extubation times of patients in the observation group and the control group after awakening were 8.52±0.41 min and 10.42±1.12 min,respectively,with statistically significant differences(P<0.05)The hospital stay after the operation in the observation group and the control group was 32.91±4.71 days and 37.24±3.34 days respectively,and the difference was statistically significant(P<0.05),and the incidence rate of adverse reactions after extubation in the observation group(3.33%)was significantly lower than that in the control group(10.00%)(P<0.05).Conclusion:In general anesthesia surgery patients,the implementation of anesthesia recovery nursing with heat preservation measures can significantly improve the physical condition of patients,effectively shorten the duration of surgery and patients’wake-up time,and improve their quality of life,which is worthy of clinical promotion and application.

Waste Heat Recovery from a Drier Receiver of an A/C Unit Using Thermoelectric Generators

Thermoelectric generators(TEGs)are considered promising devices for waste heat recovery from various systems.The Seebeck effect can be utilized to generate power using the residual heat emitted by the filter dryer receiver(FDR)of an air conditioning(A/C)system,which would otherwise go to waste.The study aims to build a set of thermoelectric generators(TEG)to collect the waste heat of the FDR and generate low-power electricity.A novel electrical circuit with two transformers is designed and fabricated to produce a more stable voltage for operation and charging.The thermoelectric generator(TEGs)was installed on the FDR of the A/C unit.The test showed that climate conditions have a significant impact on the output power generated from the system.The results showed that the peak voltage recorded in the current study is 5.2 V per day(wet,cold,and wind weather)with an output power of 0.2 W.These values are acceptable for powering the load and charging a single battery with 3.5 V as the voltage increases battery 0.1 V/20 min charge.A case study of operating the emergency signs in a building was considered.The current heat recovery system is deemed to be easily installed and can be connected to a network of TEGs to produce more power.

Waste heat recovery from hot steel slag on the production line:Numerical simulation,validation and industrial test

Waste heat recovery from hot steel slag was determined in a granular bed through the combination of numerical simulation and an industrial test method.First,the effective thermal conductivity of the granular bed was calculated.Then,the unsteady-state model was used to simulate the heat recovery under three different flow fields(O-type,S-type,and nonshielding type(Nontype)).Second,the simulation results were validated by in-situ industrial experiments.The two methods confirmed that the heat recovery efficiencies of the flow fields from high to low followed the order of Nontype,S-type,and O-type.Finally,heat recovery was carried out under the Nontype flow field in an industrial test.The heat recovery efficiency increased from~76%and~78%to~81%when the steel slag thickness decreased from 400 and 300 to 200 mm,corresponding to reductions in the steel slag mass from 3.96 and 2.97 to 1.98 t with a blower air volume of 14687 m^(3)/h.Therefore,the research results showed that numerical simulation can not only guide experiments on waste heat recovery but also optimize the flow field.Most importantly,the method proposed in this paper has achieved higher waste heat recovery from hot steel slag in industrial scale.

Full neurological recovery from severe nonexertional heat stroke with multiple organ dysfunction:A case report

BACKGROUND We report a rare case of full neurological recovery from severe nonexertional heat stroke in a 67-year-old woman with an initial Glasgow Coma Scale of 3.This report raises awareness among doctors that when heatstroke is diagnosed,comprehensive treatment should be implemented as soon as possible.Moreover,targeted temperature management,combination therapy with hemodialysis and hemoperfusion,and hyperbaric oxygen therapy may alleviate multiorgan failure and prevent neurological sequelae caused by heatstroke.CASE SUMMARY A previously healthy 67-year-old woman with an initial Glasgow Coma Scale of 3 was found lying prone on the road at noon on a summer day.Laboratory tests revealed multiorgan failure.As soon as heatstroke was diagnosed,comprehensive treatment was implemented.On hospital Day 3,the patient was extubated.Her initial Sequential Organ Failure Assessment score at hospitalization was 14 and decreased to 2 on hospital Day 4.On the seventh day following hospital admission,as the patient’s general condition improved,the levels of laboratory test findings decreased rapidly.Finally,the patient gradually recovered with no other neurological symptoms(the Glasgow Coma Scale at discharge was 15,and her ability to walk independently was restored).CONCLUSION This case demonstrated that targeted temperature management,combination therapy with hemodialysis and hemoperfusion,and hyperbaric oxygen therapy may alleviate multiorgan failure and prevent neurological sequelae caused by heatstroke.

Off-Design Simulation of a CSP Power Plant Integrated with aWaste Heat Recovery System

Concentrating Solar Power(CSP)plants offer a promising way to generate low-emission energy.However,these plants face challenges such as reduced sunlight during winter and cloudy days,despite being located in high solar radiation areas.Furthermore,their dispatch capacities and yields can be affected by high electricity consumption,particularly at night.The present work aims to develop an off-design model that evaluates the hourly and annual performances of a parabolic trough power plant(PTPP)equipped with a waste heat recovery system.The study aims to compare the performances of this new layout with those of the conventional Andasol 1 plant,with the aim of assessing the improvements achieved in the new design.Based on the results,it can be concluded that the new layout has increased the annual generated power to almost 183 GWh(an increase of about 7.60% is achieved compared to the Andasol 1 layout that generates 169 GWh annually).Additionally,the proposed installation has achieved an efficiency of 20.55%,which represents a 7.87% increase compared to the previous design(19.05%).The Levelized Cost of Electricity(LCOE)of the new layout has been reduced by more than 5.8% compared to the Andasol 1 plant.Specifically,it has decreased from 13.11 to 12.35 c/kWh.This reduction in LCOE highlights the improved cost-effectiveness of the newlayout,making it amore economically viable option for generating electricity compared to the conventional Andasol 1 plant.

Integration of Low-level Waste Heat Recovery and Liquefied Nature Gas Cold Energy Utilization

Two novel thermal cycles based on Brayton cycle and Rankine cycle are proposed, respectively, which integrate the recovery of low-level waste heat and Liquefied Nature Gas （LNG） cold energy utilization for power generation. Cascade utilization of energy is realized in the two thermal cycles, where low-level waste heat,low-temperature exergy and pressure exergy of LNG are utilized efficiently through the system synthesis. The simulations are carried out using the commercial Aspen Plus 10.2, and the results are analyzed. Compared with the conventional Brayton cycle and Rankine cycle, the two novel cycles bring 60.94% and 60% in exergy efficiency, respectively and 53.08% and 52.31% in thermal efficiency, respectively.

Same Recovery Level of Compressed Chinese Fir Wood Can Be Obtained Through Different Heating Fixation Pathways

The recovery of compression set (RS) of wood after dry heating or steam treatment mainly depends on the temperature and time of treatment. For quantitative elucidation, a graph of intermediate RS was built with temperature (T) and time (t) as coordinates. In this graph (abbreviated as T-t planum), a series of curves of RS were created. This leads to a conclusion that same RS can be obtained by numerous different pathways. Further research on pathway equivalency based on T-t planum indicates that a low RS of 10% can be achieved definitely by different combinations of time and temperature. However, the fixation mechanism varies at different temperatures. On the equivalent pathways of higher recovery, the influence of temperature must be taken into consideration. The actual routes must be somewhat modified to achieve an expected result. This makes it possible for us to work out a best fixation pathway among all the possibilities, to eliminate the impact of heat on the mechanical properties of wood.

Exploring heating performance of gas engine heat pump with heat recovery

In order to evaluate the heating performance of gas engine heat pump（GEHP） for air-conditioning and hot water supply, a test facility was developed and experiments were performed over a wide range of engine speed（1400-2600 r/min）, ambient air temperature（2.4-17.8 ℃） and condenser water inlet temperature（30-50℃）. The results show that as engine speed increases from 1400 r/min to 2600 r/min, the total heating capacity and energy consumption increase by about 30% and 89%, respectively; while the heat pump coefficient of performance（COP） and system primary energy ratio（PER） decrease by 44% and 31%, respectively. With the increase of ambient air temperature from 2.4 ℃ to 17.8 ℃, the heat pump COP and system PER increase by 32% and 19%, respectively. Moreover, the heat pump COP and system PER decrease by 27% and 15%, respectively, when the condenser water inlet temperature changes from 30 ℃ to 50 ℃. So, it is obvious that the effect of engine speed on the performance is more significant than the effects of ambient air temperature and condenser water inlet temperature.

Optimizing Low-Temperature Heat Recovery in a Refinery Fluid Catalytic Cracking Unit Based on Pinch Analysis

In this paper, the research was focused on optimizing low-temperature heat recovery to adopt multi-effect distil- lation （MED） in desalination by pinch technology. And further analysis indicated that phase changes occurred during the heat recovery process. In such case, the feed stream was divided into two streams： the liquid feed stream and the gaseous feed stream. Through calculation, the optimal ATmin was established at 26℃, and the total cost of heat exchange process was only $1.098× 106. By using the Problem Table Algorithm for pinch analysis, the temperature of the hot and the cold steams was 119℃ and 93 ℃, respectively. At a temperature higher than 119 ℃, all heat of the hot stream could not be cooled by the condenser, and the minimum heat load of utility （QH.min） was 440457.64 kW; and at a temperature below 93 ℃, all heat of the cold stream could not be provided by the heater, and the minimum cold load of utility （QC.min） was 1965993.85 kW. Finally, the synthesis of heat exchanger network was established through integrating two heat exchanger networks.

Selecting Suitable Heat Source in Refinery for Multi-effect Distillation Based on Grey System Theory

For dealing with high-salinity wastewater in the refinery, the high cost of driving heat source is the disadvantage of multi-effect distillation (MED) so it is of great importance to evaluate the performance of low-temperature heat source for conducting MED and select the optimal temperature for it. Both the MED and the low-temperature heat sources studied in this paper were from a typical refinery located in northwestern China. Besides, a new methodology to evaluate heat sources as the optimal candidate was proposed for MED based on the grey system theory. Five process units, which included 18 fluids of the refinery, were named as the evaluation projects. Three factors, which included safety effects, total costs and characteristics of low-temperature heat sources were determined as the evaluation indexes, the values of which were established through the analyses. The results obtained through the grey correlation analyses have revealed that the grey correlation degrees of these units were 0.661(AVDU), 0.732 (#1 FCCU), 0.618 (#2 FCCU), 0.535 (#1 DCU), and 0.572 (#2 DCU), respectively. Thus, the optimal heat source was provided from #1 FCCU. Through further analyses of the fluids from #1 FCCU, the grey correlation degrees of the fluids were 0.597 (oil and gas at top of tower), 0.714 (recycle oil and gas), and 0.512 (diesel), respectively. Thus, the optimal heat source was the oil and gas recycle stream.

Simulation of CO_2 Brayton Cycle for Engine Exhaust Heat Recovery under Various Operating Loads

A bottoming cycle system based on CO2 Brayton cycle is proposed to recover the engine exhaust heat. Its performance is compared with the conventional air Brayton cycle under five typical engine conditions. The results show that CO2 Brayton cycle proves to be superior to the air Brayton cycle in terms of the system net output power, thermal efficiency and recovery efficiency. In most cases, the recovery efficiency of CO2 Brayton cycle can be higher than 9% and the system has a better performance at the engine＇s high operating load, The thermal efficiency can be as large as 24.83% under 100% olaerating load, accordingly, the net outnut nower of 14.86 kW in nhtnined

Techno-economic feasibility assessment of a diesel exhaust heat recovery system to preheat mine intake air in remote cold climate regions

Underground mines in Arctic and Subarctic regions require the preheating of mine intake air during winter.The cold fresh air of those remote areas can be as severe as
40℃ and commonly needs to be heated to around+3℃.This extensive amount of heating is usually provided by employing large-size air heaters,fueled by diesel,propane,natural gas,or heavy oil,leading to high energy costs and large carbon footprints.At the same time,the thermal energy content of a diesel generator sets(gen-sets)exhaust is known to be one-third of the total heating value of its combusted fuel.Exhaust heat recovery from diesel gen-sets is a growing technology that seeks to mitigate the energy costs by capturing and redirecting this commonly rejected exhaust heat to other applications such as space heating or pre-heating of the mine intake air.The present study investigated the possibility of employing a simple system based on off-theshelf heat exchanger technology,which can recover the waste heat from the exhaust of the power generation units(diesel gen-sets)in an off-grid,cold,remote mine in Canada for heating of the mine intake air.Data from a real mine was used for the analysis along with environmental data of three different location-scenarios with distinct climates.After developing a thermodynamic model,the heat savings were calculated,and an economic feasibility evaluation was performed.The proposed system was found highly viable with annual savings of up to C$6.7 million and capable enough to provide an average of around 75%of the heating demand for mine intake air,leading to a payback period of about eleven months or less for all scenarios.Deployment of seasonal thermal energy storage has also been recommended to mitigate the mismatch between supply and demand,mainly in summertime,possibly allowing the system to eliminate fuel costs for intake air heating.

Selection of Heat Recovery Ventilators in Different Climate Zones of China

Considering four different climate zones in China, an investigation on the choice of heat recovery ventilator for the buildings with little moisture emissions is carried out. The annual composition of energy consumption of air intake for per unitary air ventilation flow rate is evaluated by employing the testing data of climatic parameters in eight selected cities. The analysis shows that the total heat recovery is suitable in a controlled ventilation system with air humidity controlled during heating period of all the climates. For the building without air humidity controlled in winter, the sensible heat recovery ventilators can be used in severe cold and cold regions, and total heat recovery systems are more suitable for energy saving in hot summer and cold winter and hot summer and warm winter regions.

Parametric optimization of packed bed for activated coal fly ash waste heat recovery using CFD techniques

Coal fly ash is an industrial solid waste generated from coal preparation during the processing and cleaning of coal for electric power generation.Comprehensive investigation on the reutilization of waste heat of activated coal fly ash is of great economic significance.The method of recovering the waste heat,proposed in this study,is the transfer of heat from activated coal fly ash to gas with the movement of air using the packed bed,providing valuable energy sources for preheating the raw coal fly ash to reduce the overall energy consumption.The investigation is carried on the heat transfer characteristics of gas–solid(activated coal fly ash)phases and air temperature fields of the packed bed under some key conditions via computational fluid dynamics.A two dimensional geometry is utilized to represent key parts of packed bed.The distribution mechanism of the temperature field for gas phase is analyzed based on the transient temperature contours at different times.The results show that the obtained rule of gas–solid heat transfer can effectively evaluate the influences of operating parameters on the air temperature in the packed bed.Simultaneously,it is found that no temperature differences exist in the hot air at the outlet of the packed bed.The investigation provides guidance for the design and optimization of other similar energy recovery apparatuses in industries.

Dynamic test on waste heat recovery system with organic Rankine cycle

Dynamic performance is important to the controlling and monitoring of the organic Rankine cycle(ORC) system so to avoid the occurrence of unwanted conditions. A small scale waste heat recovery system with organic Rankine cycle was constructed and the dynamic behavior was presented. In the dynamic test, the pump was stopped and then started. In addition, there was a step change of the flue gas volume flow rate and the converter frequency of multistage pump, respectively. The results indicate that the working fluid flow rate has the shortest response time, followed by the expander inlet pressure and the expander inlet temperature.The operation frequency of pump is a key parameter for the ORC system. Due to a step change of pump frequency(39.49-35.24 Hz),the expander efficiency and thermal efficiency drop by 16% and 21% within 2 min, respectively. Besides, the saturated mixture can lead to an increase of the expander rotation speed.

Simulation of Gas-Fired Triple-Effect LiBr/Water Absorption Cooling System with Exhaust Heat Recovery Generator

An exhaust heat recovery generator is proposed to be integrated with conventional gas-fired triple-effect LiBr/water absorption cooling cycles to improve system energy efficiency. As a case study, simulation of the novel cycle based on promising parallel flow with cooling capacity of 1 150 kW is carried out under various heat recovery generator vapor production ratios ranging from 0 to 3.5%. The life cycle saving economic analysis, for which the annual gas conservation is estimated with Bin method, is employed to prove the worthiness of extra expenditure. Results show that the optimum gas saving revenue is obtained at 2.8% heat recovery generator vapor production ratio with 42 kW exhaust heat recovered, and the system energy efficiency is improved from 1.78 to 1.83. The initial investment of exchanger can be paid back within 7 years and 9 000 CNY of gas saving revenue will be achieved over the 15-year life cycle of the machine. This technology can be easily implemented and present desirable economic effects, which is feasible to the development of triple-effect absorption cycles.

Performance Assessment of a Heat Recovery Unit Utilizing Turbine with Variable Inlet Guide Vanes Configuration for Application in Passenger Vehicles

This study explores the potentials of employing an Organic Rankine Cycle (ORC) system with variable inlet guide vanes (VIV) turbine geometry designed on a GT-Suite platform for effective exhaust heat recovery (EHR) application onboard passenger vehicles. The ORC model simulation was based on vehicle speed mode using R245fa as working fluid to assess the thermal performance of the ORC system when utilizing modified turbine geometry. Interestingly, the model achieved a very improved performance in contrast to the model without a modified turbine configuration. The results revealed the average 2.32 kW ORC net output, 4.93% thermal efficiency, 6.1% mechanical efficiency, and 5.0% improved brake specific fuel consumption (BSFC) for the developed model. As determined by the performance indicators, these promising results from the model study show the prospect of EHR technology application in the transportation sector for reduction in exhaust emissions and fuel savings.

Performance and Optimization for a Ground-Coupled Liquid Loop Heat Recovery Ventilation System

Ground-coupled heat pumps(GCHP)are commonly used in residential heating system.To mitigate the boreholes temperature dropping with operating time,a new exhaust-air recharging system is developed.The new recharging system can be used in three operational modes.In this paper,a ground-coupled heat recovery ventilation(HRV)model is discussed.A thermal model is set up to find the optimal brine flow rate and heat transfer allocation ratio between exhaust and supply coils for maximum heat recovery efficiency.Contrary to the conventional liquid-loop HRV systems,the brine temperature entering the exhaust coil never goes blow zero(0℃),and hence defrosting is needless in the ground-coupled HRV system.This can make the ground-coupled HRV system over 20% more efficient than a conventional HRV system at low outdoor temperatures.