Wetting front migration model of ion-adsorption rare earth during the multi-hole unsaturated liquid injection

In the process of ion-adsorption rare earth ore leaching,the migration characteristics of the wetting front in multi-hole injection holes and the influence of wetting front intersection effect on the migration distance of wetting fronts are still unclear.Besides,wetting front migration distance and leaching time are usually required to optimize the leaching process.In this study,wetting front migration tests of ionadsorption rare earth ores during the multi-hole fluid injection(the spacing between injection holes was 10 cm,12 cm and 14 cm)and single-hole fluid injection were completed under the constant water head height.At the pre-intersection stage,the wetting front migration laws of ion-adsorption rare earth ores during the multi-hole fluid injection and single-hole fluid injection were identical.At the postintersection stage,the intersection accelerated the wetting front migration.By using the Darcy’s law,the intersection effect of wetting fronts during the multi-hole liquid injection was transformed into the water head height directly above the intersection.Finally,based on the Green-Ampt model,a wetting front migration model of ion-adsorption rare earth ores during the multi-hole unsaturated liquid injection was established.Error analysis results showed that the proposed model can accurately simulate the infiltration process under experimental conditions.The research results enrich the infiltration law and theory of ion-adsorption rare earth ores during the multi-hole liquid injection,and this study provides a scientific basis for optimizing the liquid injection well pattern parameters of ion-adsorption rare earth in situ leaching in the future.

Lance-Adams综合征1例

Lance-Adams综合征，又称为继发于低氧性脑病的意向性或动作性肌阵挛综合征。国内关于治疗Lance-Adams综合征的报道相对较少，我院通过采用地西泮、丙戊酸等抗癫痫药物对1例Lance-Adams综合征患者进行治疗，并观察其临床表现及脑电图情况，以探究Lance-Adams综合征的临床发病特点及治疗方法，提高对Lance-Adams综合征的认识，便以早诊断、及时救治。经过一系列的治疗之后，患者的临床症状得到有效控制，脑电图结果由起初以3~5 Hz的高频兹波、啄波为主，伴有中、高幅尖、棘波以及棘慢综合波逐渐转变为以8~10 Hz有节律的α波为主，尖、棘波以及棘慢综合波消失。本病例的发病过程及体征情况与相关文献基本相符，经过丙戊酸、地西泮等抗癫痫药物治疗后，病情得到有效缓解，生存质量明显提高，说明丙戊酸、地西泮等抗癫痫药物可作为治疗Lance-Adams综合征的一个选择。

基于Lance距离和信度熵的冲突证据融合方法

针对D-S(Dempster-Shafer)证据理论中证据融合可能存在冲突的问题,通过考虑证据之间的关系及其本身的特性,提出一种基于Lance距离和信度熵的冲突证据融合方法。首先,利用Lance距离来度量证据之间的差异和冲突程度,并通过矩阵形式表示证据的可信度,再通过计算信度熵来度量证据的信息量,并以此表示证据的不确定度。其次,综合考虑证据的可信度和不确定度来衡量证据最终融合的折扣系数,并通过折扣系数修正原始证据。最后,采用Dempster合成规则进行证据融合得到最终结果。算例分析结果表明,所提方法较其他方法而言,收敛速度更快,融合结果更准确、可靠。

Lance-Adams综合征二例报道并文献复习

本文报道了2例缺氧后肌阵挛发作病例,通过复习文献,对其病因学、临床表现、诊断要点与治疗情况进行分析,发现其有下述临床特点:(1)心肺复苏、窒息是本病常见的原因;(2)肌阵挛易由外界刺激所诱发,如听觉、触觉、视觉刺激诱发或加重;(3)脑电图有或无痫性电活动,脑部影像学检查可无特异性病变;(4)治疗首选丙戊酸、氯硝西泮等抗癫痫药;(5)总体预后较好,可能遗留神经功能缺损。

Study on Rapid Propagation Medium of Atractylodes Lances by Orthogonal Design

[Objective] The aim was to protect wild resource of Atractylodes lances and to provide technical guidance for industrialization of Atractylodes lances. [Method] The test-tube seedlings were produced from seeds of Atractylodis Lances. At the same time, the effects of 6-BA, NAA and KT on the proliferation of aseptic seedling was studied through the orthogonal test. Effect of NAA concentration on the rooting of aseptic seedling was studied through nine types of light substrate groups, which consist of peat soil, fine sand and cotton seed hull, and their effects on Atractylodes lances growth were studied on with orthogonal design. [Result] The culture medium suitable for the proliferation of the Atractylodes lances tube seedling was MS＋6-BA 1.0 mg/L＋NAA 0.4 mg/L＋KT 0,4 mg/L. And the medium suitable for rooting was 1/2MS＋NAA 0.5 mg/L. The optimal ratio of soil, riversand and cotton seed hull was 3：3：2. [Conclusion] The research selected optimum culture medium, rooting medium and ratio of substrate, which provided technical guidance for laboratorial preservation of germplasm resource of Atractylodes lances and industrialization of its seedling production.

Jet Behavior and Metallurgical Performance of Innovated Double-Parameter Oxygen Lance in BOF

A double-parameter oxygen lance used in a 300 t converter was designed to improve the metallurgical performance. A small-scale measurement of the jet behavior was done using a computer controlled scanning system. The experimental data on the velocity distribution at the jet centerline, the contour map of the jet velocity, the deviation of the jet centerline, and the velocity distribution of the axial section were compiled. According to the results of the small-scale measurement, the double-parameter lance was also employed for a BOF experiment. The metallurgy inde- xes show that the metallurgical performance was highly promoted by use of the double-parameter lance.

Simulation of three-phase flow and lance height effect on the cavity shape

A three-dimensional computational fluid dynamics （CFD） model was developed to simulate a 150-t top-blown converter. The ef-fect of different lance heights on the cavity shape was investigated using the volume of fluid （VOF） method. Numerical simulation results can reflect the actual molten bath surface waves impinged by the supersonic oxygen jets. With increasing lance height, the cavity depth de-creases, and the cavity area, varying like a parabola, increases and then decreases. The cavity area maximizes at the lance height of 1.3 m. Under the three different lance heights simulated in this study, all of the largest impact velocities at the molten bath surface are between 50 m/s and 100 m/s.

Experimental investigation of key parameters pertinent to multi-hole orifice throttling characteristic

This study firstly defines a set of arrangement rule for perforated holes of multi-hole orifice(MO), and then presents three critical geometrical parameters including total number of performated hole, equivalent diameter ratio and distribution density of perforated holes, which are to quantify MO structure. This paper built the throttling test apparatus for nice test MO plates, which were designed according to orthogonal theory. The experiments were conducted to investigate the effect of three critical geometerical parameters on the pressure loss coefficient of test MOs. Results show that equivalent diameter ratio is the dominant prameter affecting MO throttling characterstic.

Influence of the Hole Chamfer on the Characteristics of a Multi-hole Orifice Flowmeter

In order to analyze the influence of the hole chamfer on the metering performances of a Multi-hole Orifice Flowmeter and optimize the related orifice structure,a multi-hole orifice flowmeter with DN80 and throttle ratio of 0.45 was considered in the present study.The flow field characteristics were determined in the framework of a CFD technique.The results show that the multi-hole orifice flowmeter with filleting transition around the throttle orifice has higher accuracy in a wide range of the space of parameters,and is more suitable for accurate measurement of fluid in process control.

Multi-hole joint acquisition of a 3D-RVSP in a karst area:Case study in the Wulunshan Coal Field,China

Conventional surface seismic exploration in areas with complex surfaces such as karst landforms has been faced with the problem of poor excitation and reception conditions.RVSP(reverse vertical seismic profile)seismic exploration adopts a geometry in which the sources are downhole and receivers are on the ground which can reduce the influence of complex surfaces on seismic wave propagation(to some extent).Through numerical simulations and real data analysis,it was noted that in areas with complex surfaces and large numbers of underground karst caves,seismic waves generated in shallow boreholes are easily affected by various surface and multiple waves as well as by scattering from karst bodies.Therefore,the quality of the reflected seismic data is extremely low.Also,it is difficult to improve the signal to noise ratio(SNR)with conventional noise filtering methods.However,when the source depth is increased,the quality of the reflected waves can be improved.This is exactly what the RVSP method accomplishes.Besides,for the RVSP method,due to its particular geometry,the apparent velocities of the reflected waves and most interference waves are quite different,which can help to filter most noise to further improve the SNR of the reflected signals.In this study,a 3 D-RVSP exploration study using 8-hole joint acquisition was conducted in a typical karst landform.The results show that the 3 D-RVSP method can obtain higher quality seismic data for complex surface conditions that have large numbers of underground karst caves.Furthermore,multi-hole joint acquisition for 3 D-RVSP has higher data collection efficiency and better uniformity of underground coverage.Therefore,in this study,38 faults were accurately revealed and at high resolution based on the 3 D-RVSP imaging results.

Experimental study of a simple pressure loss coefficient model for multi-hole orifice

A throttling experiment for the multi-hole orifice （MO） using water was conducted based on the conclusion of key parameters affecting the MO throttling performance. Testing MOs and standard orifice plates （ SO ） were designed for the throttling experiment to compare the throttling effect using the equivalent diameter ratio （RED） and diameter ratio （RD ） as key parameters, respectively. Meanwhile, effective metrical conditions were provided for experimental accuracy. The throttling model form was determined according to the theoretical throttling model of SO. Then the unknown parameters involved were identified by experimental data. A good concordance between the modeling computation and experimental results shows a validation of the MO throtting model.

Single-mode low threshold current multi-hole vertical-cavity surface-emitting lasers

A multi-hole vertical-cavity surface-emitting laser （VCSEL） operating in stable single mode with a low threshold current was produced by introducing multi-leaf scallop holes on the top distributed Bragg-refleetor of an oxidation- confined 850 nm VCSEL. The single-mode output power of 2.6 mW, threshold current of 0.6 mA, full width of half maximum lasing spectrum of less than 0.1 nm, side mode suppression ratio of 28.4 dB, and far-field divergence angle of about 10% are obtained. The effects of different hole depths on the optical characteristics are simulated and analysed, including far-field divergence, spectrum and lateral cavity mode. The single-mode performance of this multi-hole device is attributed to the large radiation loss from the inter hole spacing and the scattering loss at the bottom of the holes, particularly for higher order modes.

A new analytical-numerical method for calculating interacting stresses of a multi-hole problem under both remote and arbitrary surface stresses

Based on the elementary solutions and new integral equations,a new analytical-numerical method is proposed to calculate the interacting stresses of multiple circular holes in an infinite elastic plate under both remote stresses and arbitrarily distributed stresses applied to the circular boundaries.The validity of this new analytical-numerical method is verified by the analytical solution of the bi-harmonic stress function method,the numerical solution of the finite element method,and the analytical-numerical solutions of the series expansion and Laurent series methods.Some numerical examples are presented to investigate the effects of the hole geometry parameters(radii and relative positions)and loading conditions(remote stresses and surface stresses)on the interacting tangential stresses and interacting stress concentration factors(SCFs).The results show that whether the interference effect is shielding(k<1)or amplifying(k>1)depends on the relative orientation of holes(α)and remote stresses(σ^∞x,σ^∞y).When the maximum principal stress is aligned with the connecting line of two-hole centers andσ^∞y<0.5σ^∞x,the plate containing two circular holes has greater stability than that containing one circular hole,and the smaller circular hole has greater stability than the bigger one.This new method not only has a simple formulation and high accuracy,but also has an advantage of wide applications over common analytical methods and analytical-numerical methods in calculating the interacting stresses of a multi-hole problem under both remote and arbitrary surface stresses.

Development of a biliary multi-hole self-expandable metallic stent for bile tract diseases: A case report

BACKGROUND Uncovered stents used for malignant obstructions in the biliary tree, especially in the hilar area, are prone to obstruction by tumor ingrowths. In comparison, however, covered stents may block bile duct branches and are at risk of migration. We have developed a multi-hole self-expandable metallic stent (MHSEMS), with a hole in each cell, to prevent the obstruction of bile duct branches. In addition, the holes may prevent migration due to small ingrowths by reducing the tension of the membrane. CASE SUMMARY MHSEMS were placed in five patients with a malignant obstruction and one with post-endoscopic sphincterotomy bleeding. Each MHSEMS was successfully deployed in all cases. Patients showed no complications. Two cases were reviewed. Case 1: A 74-year-old male presented with jaundice and was diagnosed with a sigmoid colon cancer and giant liver metastases in the right liver lobe. A MHSEMS was placed in the left bile duct. The jaundice improved and peroral cholangioscopy was performed. Case 2: A 90-year-old female was admitted to hospital for jaundice and diagnosed with cholangiocarcinoma. A MHSEMS was placed in the left bile duct but after 8 months the stent became obstructed by tumor ingrowth. We treated the patient by ablation therapy. A silicone cover separated the internal bile duct from the surrounding tissue, protecting the latter from thermal injury during treatment by endobiliary ablation of the reobstruction. CONCLUSION A MHSEMS is a new choice of stent for biliary tract diseases.

加权犹豫模糊集的Lance距离测度及其应用

在多属性群决策过程中,犹豫模糊元中不同隶属度所占权重直接影响最终的评价结果。因此,提出一种基于加权犹豫模糊集的Lance距离多属性群决策方法。利用加权犹豫模糊集的熵构造属性信息权重的确定模型,给出加权犹豫模糊集的Lance距离的TOPSIS方法以及生成算法。通过流感疫苗供货商的选择,验证了该方法是可行的和有效的。

Case Report:Lance-Adams syndrome:a report of two cases

Chronic post-hypoxic myoclonus, also known as Lance-Adams syndrome (LAS), is a rare complication of successful cardiopulmanry resuscitation often accompanied by action myoclonus and cerebellar ataxia. It is seen in patients who have un-dergone a cardiorespiratory arrest, regained consciousness afterwards, and then developed myoclonus days or weeks after the event. Worldwide, 122 cases have been reported in the literature so far, including 1 case of Chinese. Here we report 2 Chinese LAS patients with detailed neuroimagings. Cranial single photon emission computed tomography (SPECT) of patient 1, a 52-year-old woman, showed a mild hypoperfusion in her left temporal lobe, whereas patient 2, a 54-year-old woman, manifested a mild bilateral decrease of glucose metabolism in the frontal lobes and a mild to moderate decrease of the N-acetyl aspartate (NAA) peak in the bilateral hippocampi by cranial [18F]-fluorodeoxyglucose positron emission tomographic (PET) scan and cranial magnetic resonance spectroscopy (MRS), respectively. We also review the literature on the neuroimaging, pathogenesis, and treatment of LAS.

Lance Design for Argon Bubbling in Molten Steel

Three lance designs for argon bubbling in molten steel are presented. Bottom bubbling is considered too. Geometries considered are straight-shaped, T-shaped, and disk-shaped. The bubbling behavior of these lances is analyzed using Computational Fluid Dynamics, so transient three dimensional, isothermal, two-phase, numerical simulations were carried out. Using the numerical results, the bubble distribution and the open eye area are analyzed for the considered lance geometries. The plume volume is calculated from the open eye area and the lance immersion depth using geometrical considerations. Among the three lance designs considered, disk-shaped lance has the bigger plume volume and the smaller mixing time. As the injection lance is deeper immersed, the power stirring is increased and the mixing time is decreased.

Optimization Design of Multi-hole and Varied Diameter Pipe Based on RAGA

Combining real accelerating genetic algorithm(RAGA) with the optimization design of multi-hole and varied diameter pipe, the authors solved the problem of optimizing multi-dimensional parameters at the same time. In which the advanced convergence and easily to run into partial optimization were avoid. Applied the RAGA to solving the problem in the optimization design of fixed piping sprinkler irrigation system. The optimized parameters, such as diameters and the length of pipe were calculated and the result was reasonable, which provides as a reference to readers who work at related research.

＂Big Sissy＂： The Queer Construction of Lance Loud

The continued popularity of reality television, and the release of the recent HBO film Cinema Verite--about the production of the first ＂reality show,＂ An American Family （1973） --has resulted in renewed interest in the series and tangentially its other distinction--its portrayal of the first openly gay character on prime time television. Lance, the oldest of the Loud family children, is on film both flamboyant and effusive, but at the same time-through judicious editing--an asexual creature with no romantic or sexual relationships. This paper considers Lance in the context of Gay representation in media of the 1970s, and then explores the struggle of the filmmakers--and the Loud family themselves--to control and contain the public perception of Lance. The often vague and allusive comments by Lance＇s parents and even Lance himself suggest a character that is at once channing, witty, and vibrantly alive, yet also pretentious and deceitful. The final argument is that these complicit efforts to avoid controversy actually engender it, turning Lance Loud into a figure of mystery and conjecture ... and the undisputed star of the series.

Stability Analysis of a Multi-holes Shell Under Axial Compression

The paper presents a multi-holes shell with one hundred and eighty circular holes which has been used in engineering. Using a buckling module of the finite element analysis software, stability behavior and destroy mode along geometry parameters are studied. Results show the destroy mode depends on the geometry parameter greatly. Curves of buckling critical load and strength limited load along geometry parameters have a point of intersection. The point implies the multi-holes shell has different destroy mode and the value of point is change in geometry parameters.