Blast wave characteristics of multi-layer composite charge:Theoretical analysis,numerical simulation,and experimental validation

This article investigates the characteristics of shock wave overpressure generated by multi-layer composite charge under different detonation modes.Combining dimensional analysis and the explosion mechanism of the charge,a peak overpressure prediction model for the composite charge under singlepoint detonation and simultaneous detonation was established.The effects of the charge structure and initiation method on the overpressure field characteristics were investigated in AUTODYN simulation.The accuracy of the prediction model and the reliability of the numerical simulation method were subsequently verified in a series of static explosion experiments.The results reveal that the mass of the inner charge was the key factor determining the peak overpressure of the composite charge under single-point detonation.The peak overpressure in the radial direction improved apparently with an increase in the aspect ratio of the charge.The overpressure curves in the axial direction exhibited a multi-peak phenomenon,and the secondary peak overpressure even exceeded the primary peak at distances of 30D and 40D(where D is the charge diameter).The difference in peak overpressure among azimuth angles of 0-90°gradually decreased with an increase in the propagation distance of the shock wave.The coupled effect of the detonation energy of the inner and outer charge under simultaneous detonation improved the overpressure in both radial and axial directions.The difference in peak overpressure obtained from model prediction and experimental measurements was less than 16.4%.

Limit analysis of ultimate uplift capacity and failure mechanism ofshallow plate anchors in multi-layered soils

Considering the fact that in some complex cases,plate anchors are buried in multi-layered geotechnical materials,the ultimate dynamic analysis was performed to investigate the uplift capacity and failure mechanism of shallow strips and circular plate anchors in multi-layered soils.The nonlinear strength criterion and non-associated flow rule of geotechnical materials were introduced to investigate the influence of nonuniformity on the pullout performance and failure mechanism of shallow plate anchors.The expressions of the detaching curves or surfaces were obtained to reflect the failure mechanism,which can be used to figure out the ultimate uplift capacity and failure range.The results are generally in agreement with the numerical simulations and previous research.The effects of various parameters on the ultimate uplift capacity and failure mechanism of plate anchors in multi-layered soils were investigated,and it is found that the ultimate uplift capacity and failure range of shallow anchors increase with the increase of initial cohesion and dilatancy coefficient,but decrease with the unit weight,axial tensile stress and nonlinear coefficient.

Automatic Sentimental Analysis by Firefly with Levy and Multilayer Perceptron

The field of sentiment analysis(SA)has grown in tandem with the aid of social networking platforms to exchange opinions and ideas.Many people share their views and ideas around the world through social media like Facebook and Twitter.The goal of opinion mining,commonly referred to as sentiment analysis,is to categorise and forecast a target’s opinion.Depending on if they provide a positive or negative perspective on a given topic,text documents or sentences can be classified.When compared to sentiment analysis,text categorization may appear to be a simple process,but number of challenges have prompted numerous studies in this area.A feature selection-based classification algorithm in conjunction with the firefly with levy and multilayer perceptron(MLP)techniques has been proposed as a way to automate sentiment analysis(SA).In this study,online product reviews can be enhanced by integrating classification and feature election.The firefly(FF)algorithm was used to extract features from online product reviews,and a multi-layer perceptron was used to classify sentiment(MLP).The experiment employs two datasets,and the results are assessed using a variety of criteria.On account of these tests,it is possible to conclude that the FFL-MLP algorithm has the better classification performance for Canon(98%accuracy)and iPod(99%accuracy).

Coupling Discriminating Statistical Analysis and Artificial Intelligence for Geotechnical Characterization of the Kampemba’s Municipality Soils (Lubumbashi, DR Congo)

This study focuses on the determination of physical and mechanical characteristics based on in vitro tests, by using field samples for the Kampemba urban area in the city of Lubumbashi. At the end of this study, we identified the soils according to their parameters, and established the geotechnical classification by determining their bearing capacity by the group index method using from the identification tests carried out. By using the AASHTO classification method (American Association for State Highway Transportation Official), the results obtained after our studies revealed five classes of soil: A-2, A-4, A-5, A-6, A-7 in a general way, and particularly eight subgroups of soil: A-2-4, A-2-6, A-2-7, A-4, A-5, A-6, A-7-5 and A-7-6 for the concerned area. The latter has given statistical analysis and deep learning based on multi-layer perceptron, the global values of the physical parameters. It’s about: 31.77% ± 1.05% for the limit of liquidity;18.71% ± 0.76% for the plastic limit;13.06% ± 0.79% for the plasticity index;83.00% ± 3.33% for passing of 2 mm sieve;76.22% ± 3.2% for passing of 400 μm sieve;89.07% ± 2.99% for passing of 4.75 mm sieve;70.62% ± 2.39% passing of 80 μm sieve;1.66 ± 0.61 for the consistency index;−0.67 ± 0.62 for the liquidity index and 8 ± 1 for the group index.

A Sleep Scoring System Using EEG Combined Spectral and Detrended Fluctuation Analysis Features

Most of sleep disorders are diagnosed based on the sleep scoring and assessments. The purpose of this study is to combine detrended fluctuation analysis features and spectral features of single electroencephalograph (EEG) channel for the purpose of building an automated sleep staging system based on the hybrid prediction engine model. The testing results of the model were promising as the classification accuracies were 98.85%, 92.26%, 94.4%, 95.16% and 93.68% for the wake, non-rapid eye movement S1, non-rapid eye movement S2, non-rapid eye movement S3 and rapid eye movement sleep stages, respectively. The overall classification accuracy was 85.18%. We concluded that it might be possible to employ this approach to build an industrial sleep assessment system that reduced the number of channels that affected the sleep quality and the effort excreted by sleep specialists through the process of the sleep scoring.

Sensitivity Analysis of Radial Basis Function Networks for River Stage Forecasting

Sensitivity analysis of neural networks to input variation is an important research area as it goes some way to addressing the criticisms of their black-box behaviour. Such analysis of RBFNs for hydrological modelling has previously been limited to exploring perturbations to both inputs and connecting weights. In this paper, the backward chaining rule that has been used for sensitivity analysis of MLPs, is applied to RBFNs and it is shown how such analysis can provide insight into physical relationships. A trigonometric example is first presented to show the effectiveness and accuracy of this approach for first order derivatives alongside a comparison of the results with an equivalent MLP. The paper presents a real-world application in the modelling of river stage shows the importance of such approaches helping to justify and select such models.

Uncertainties in landslide susceptibility prediction:Influence rule of different levels of errors in landslide spatial position

The accuracy of landslide susceptibility prediction(LSP)mainly depends on the precision of the landslide spatial position.However,the spatial position error of landslide survey is inevitable,resulting in considerable uncertainties in LSP modeling.To overcome this drawback,this study explores the influence of positional errors of landslide spatial position on LSP uncertainties,and then innovatively proposes a semi-supervised machine learning model to reduce the landslide spatial position error.This paper collected 16 environmental factors and 337 landslides with accurate spatial positions taking Shangyou County of China as an example.The 30e110 m error-based multilayer perceptron(MLP)and random forest(RF)models for LSP are established by randomly offsetting the original landslide by 30,50,70,90 and 110 m.The LSP uncertainties are analyzed by the LSP accuracy and distribution characteristics.Finally,a semi-supervised model is proposed to relieve the LSP uncertainties.Results show that:(1)The LSP accuracies of error-based RF/MLP models decrease with the increase of landslide position errors,and are lower than those of original data-based models;(2)70 m error-based models can still reflect the overall distribution characteristics of landslide susceptibility indices,thus original landslides with certain position errors are acceptable for LSP;(3)Semi-supervised machine learning model can efficiently reduce the landslide position errors and thus improve the LSP accuracies.

Multi-objective optimization of the cathode catalyst layer micro-composition of polymer electrolyte membrane fuel cells using a multi-scale,two-phase fuel cell model and data-driven surrogates

Polymer electrolyte membrane fuel cells(PEMFCs)are considered a promising alternative to internal combustion engines in the automotive sector.Their commercialization is mainly hindered due to the cost and effectiveness of using platinum(Pt)in them.The cathode catalyst layer(CL)is considered a core component in PEMFCs,and its composition often considerably affects the cell performance(V_(cell))also PEMFC fabrication and production(C_(stack))costs.In this study,a data-driven multi-objective optimization analysis is conducted to effectively evaluate the effects of various cathode CL compositions on Vcelland Cstack.Four essential cathode CL parameters,i.e.,platinum loading(L_(Pt)),weight ratio of ionomer to carbon(wt_(I/C)),weight ratio of Pt to carbon(wt_(Pt/c)),and porosity of cathode CL(ε_(cCL)),are considered as the design variables.The simulation results of a three-dimensional,multi-scale,two-phase comprehensive PEMFC model are used to train and test two famous surrogates:multi-layer perceptron(MLP)and response surface analysis(RSA).Their accuracies are verified using root mean square error and adjusted R^(2).MLP which outperforms RSA in terms of prediction capability is then linked to a multi-objective non-dominated sorting genetic algorithmⅡ.Compared to a typical PEMFC stack,the results of the optimal study show that the single-cell voltage,Vcellis improved by 28 m V for the same stack price and the stack cost evaluated through the U.S department of energy cost model is reduced by$5.86/k W for the same stack performance.

Dual in-situ observation of tribochemical and morphological evolution of single-layer WS_(2)and multi-layer WS_(2)/C coatings

The outstanding tribological performance of transition metal dichalcogenides(TMDs)is attributed to their unique sandwich microstructure and low interlayer shear stress.This advantageous structure allows TMDs to demonstrate exceptional friction reduction properties.Furthermore,the incorporation of TMDs and amorphous carbon(a-C)in multi-layer structures shows excellent potential for further enhancing tribological and anti-oxidation properties.Amorphous carbon,known for its high ductility,chemical inertness,and excellent wear resistance,significantly contributes to the overall performance of these multi-layer coatings.To gain an in-depth understanding of the tribological mechanism and evolution of TMDs’multi-layer coatings,a dual in-situ analysis was carried out using a tribometer equipped with a 3D laser microscope and a Raman spectrometer.This innovative approach allowed for a comprehensive evolution of the tribological,topographical,and tribochemical characteristics of both single-layer WS_(2)and multi-layer WS_(2)/C coatings in real time.The findings from the dual in-situ tribotest revealed distinct failure characteristics between the single-layer WS_(2)coating and the multi-layer WS_(2)/C coating.The single-layer WS_(2)coating predominantly experienced failure due to mechanical removal,whereas a combination of mechanical removal and tribochemistry primarily influenced the failure of the multi-layer WS_(2)/C coating.The tribological evolution process of these two coatings can be classified into four stages on the basis of their tribological behavior:the running-in stage,stable friction stage,re-deposition stage,and lubrication failure stage.Each stage represents a distinct phase in the tribological behavior of the coatings and contributes to our understanding of their behavior during sliding.

我国稀缺矿产资源对外投资战略选区的思考

本文从我国稀缺矿产资源面临严峻的供求矛盾分析出发 ,指出对外直接投资已成为我国资源战略的重要措施。针对矿业对外投资的风险性 ,本文提出在矿业对外投资战略选区时 ,首先要分析我国的稀缺矿产资源种类 ,然后再找我国稀缺矿产资源对外投资的目标国别 ,并对目标国别的投资环境评价方法进行了探讨。

A three-dimensional nonlinear reduced-order predictive joint model

Mechanical joints can have significant effects on the dynamics of assembled structures.However,the lack of efficacious predictive dynamic models tot joints hinders accurate prediction of their dynamic behavior.The goal of our work is to develop physics-based,reduced-order,finite element models that are capable of replicating the effects of joints on vi- brating structures.The authors recently developed the so-called two-dimensional adjusted lwan beam element(2-D AIBE) to simulate the hysteretic behavior of bolted joints in 2-D beam structures.In this paper,2-D AIBE is extended to three-di- mensional cases by formulating a three-dimensional adjusted lwan beam element(3-D AIBE).hupulsive loading experi- ments are applied to a jointed frame structure and a beam structure containing the same joint.The frame is subjected to ex- citation out of plane so that the joint is under rotation and single axis bending.By assuming that the rotation in the joint is linear elastic,the parameters of the joint associated with bending in the flame are identified from acceleration responses of the jointed beam structure,using a multi-layer teed-torward neural network(MLFF).Numerieal simulation is then per- formed on the frame structure using the identified parameters.The good agreement between the simulated and experimental impulsive acceleration responses of the frame structure validates the efficacy of the presented 3-D AIBE,and indicates that the model can potentially be applied to more complex structural systems with joint parameters identified from a relatively simple structure.

Extracting invariable fault features of rotating machines with multi-ICA networks

This paper proposes novel multi-layer neural networks based on Independent Component Analysis for feature extraction of fault modes. By the use of ICA, invariable features embedded in multi-channel vibration measurements under different operating conditions (rotating speed and/or load) can be captured together.Thus, stable MLP classifiers insensitive to the variation of operation conditions are constructed. The successful results achieved by selected experiments indicate great potential of ICA in health condition monitoring of rotating machines.

Classification and Identification of Nuclear, Biological or Chemical Agents Taken from Remote Sensing Image by Using Neural Network

In the context of new risks and threats associated to nuclear, biological and chemical （NBC） attacks, and given the shortcomings of certain analytical methods such as principal component analysis （PCA）, a neural network approach seems to be more accurate. PCA consists in projecting the spectrum of a gas collected from a remote sensing system in, firstly, a three-dimensional space, then in a two-dimensional one using a model of Multi-Layer Perceptron based neural network. It adopts during the learning process, the back propagation algorithm of the gradient, in which the mean square error output is continuously calculated and compared to the input until it reaches a minimal threshold value. This aims to correct the synaptic weights of the network. So, the Artificial Neural Network （ANN） tends to be more efficient in the classification process. This paper emphasizes the contribution of the ANN method in the spectral data processing, classification and identification and in addition, its fast convergence during the back propagation of the gradient.

DM-L Based Feature Extraction and Classifier Ensemble for Object Recognition

Deep Learning is a powerful technique that is widely applied to Image Recognition and Natural Language Processing tasks amongst many other tasks. In this work, we propose an efficient technique to utilize pre-trained Convolutional Neural Network (CNN) architectures to extract powerful features from images for object recognition purposes. We have built on the existing concept of extending the learning from pre-trained CNNs to new databases through activations by proposing to consider multiple deep layers. We have exploited the progressive learning that happens at the various intermediate layers of the CNNs to construct Deep Multi-Layer (DM-L) based Feature Extraction vectors to achieve excellent object recognition performance. Two popular pre-trained CNN architecture models i.e. the VGG_16 and VGG_19 have been used in this work to extract the feature sets from 3 deep fully connected multiple layers namely “fc6”, “fc7” and “fc8” from inside the models for object recognition purposes. Using the Principal Component Analysis (PCA) technique, the Dimensionality of the DM-L feature vectors has been reduced to form powerful feature vectors that have been fed to an external Classifier Ensemble for classification instead of the Softmax based classification layers of the two original pre-trained CNN models. The proposed DM-L technique has been applied to the Benchmark Caltech-101 object recognition database. Conventional wisdom may suggest that feature extractions based on the deepest layer i.e. “fc8” compared to “fc6” will result in the best recognition performance but our results have proved it otherwise for the two considered models. Our experiments have revealed that for the two models under consideration, the “fc6” based feature vectors have achieved the best recognition performance. State-of-the-Art recognition performances of 91.17% and 91.35% have been achieved by utilizing the “fc6” based feature vectors for the VGG_16 and VGG_19 models respectively. The recognition performance has been achieved by considering 30 sample images per class whereas the proposed system is capable of achieving improved performance by considering all sample images per class. Our research shows that for feature extraction based on CNNs, multiple layers should be considered and then the best layer can be selected that maximizes the recognition performance.

Aerodynamic optimization of rotor airfoil based on multi-layer hierarchical constraint method

Rotor airfoil design is investigated in this paper. There are many difficulties for this highdimensional multi-objective problem when traditional multi-objective optimization methods are used. Therefore, a multi-layer hierarchical constraint method is proposed by coupling principal component analysis(PCA) dimensionality reduction and e-constraint method to translate the original high-dimensional problem into a bi-objective problem. This paper selects the main design objectives by conducting PCA to the preliminary solution of original problem with consideration of the priority of design objectives. According to the e-constraint method, the design model is established by treating the two top-ranking design goals as objective and others as variable constraints. A series of bi-objective Pareto curves will be obtained by changing the variable constraints, and the favorable solution can be obtained by analyzing Pareto curve spectrum. This method is applied to the rotor airfoil design and makes great improvement in aerodynamic performance. It is shown that the method is convenient and efficient, beyond which, it facilitates decision-making of the highdimensional multi-objective engineering problem.

Numerical Study on Groundwater Drawdown and Deformation Responses of Multi-Layer Strata to Pumping in a Confined Aquifer

Pumping artesian water from porous media inevitably reduces the groundwater head and promotes soil consolidation,which may result in regional land subsidence.In this study,a fluid-mechanical coupled numerical model is developed to investigate the dewatering-induced groundwater drawdown and deformation responses for multi-layer strata.The relation bet ween the stra tum deformation and groundwater drawdown is discussed.The results show that the pumping process can be divided into four st ages.The development of vertical deformation is inconsistent with the change of the pore pressure for the strata except for the confined aquifer at the early stage of pumping.The st rata expand while the pore pressures reduce.This inconsistency may be due to the large unloading in the confined aquifer at the early stage of pumping.Soil arch comes into being owing to the constraint of the surrounding soils when the large unloading occurs in the confined aquifer;this can reduce the stratum compression and cause the expansion of the layers.It can be concluded that as the pumping continues,the decrease of the pore pressure dominates the vertical deformation and results in the soil compression in all strata.

Theoretical prediction of ground settlements due to shield tunneling in multi-layered soils considering process parameters

This paper conducts a theoretical analysis of ground settlements due to shield tunneling in multi-layered soils which are usually encountered in urban areas.The proposed theoretical solution which is based on the general form of the Mindlin’s solution and Loganathan-Poulos formula can comprehensively consider the in-process tunneling parameters including:unbalanced face pressure,shield-soil friction,unbalanced tail grouting pressure,unbalanced secondary grouting pressure,overloading during tunneling and the ground volume loss.The method is verified by comparing with the field data from the Qinghuayuan Tunnel Project in terms of the ground surface settlements along the longitudinal and transverse direction.Due to the local settlement or heave caused by the certain tunneling parameters,the ground surface settlements calculated using current solution along the longitudinal direction presents an irregular S-shaped curve instead of the traditional S-shaped curve.Results also find that the effect of the unbalanced secondary grouting pressure and the overloading during tunneling cannot be ignored.

Sensitive system calls based packed malware variants detection using principal component initialized MultiLayers neural networks

Malware detection has become mission sensitive as its threats spread from computer systems to Internet of things systems.Modern malware variants are generally equipped with sophisticated packers,which allow them bypass modern machine learning based detection systems.To detect packed malware variants,unpacking techniques and dynamic malware analysis are the two choices.However,unpacking techniques cannot always be useful since there exist some packers such as private packers which are hard to unpack.Although dynamic malware analysis can obtain the running behaviours of executables,the unpacking behaviours of packers add noisy information to the real behaviours of executables,which has a bad affect on accuracy.To overcome these challenges,in this paper,we propose a new method which first extracts a series of system calls which is sensitive to malicious behaviours,then use principal component analysis to extract features of these sensitive system calls,and finally adopt multi-layers neural networks to classify the features of malware variants and legitimate ones.Theoretical analysis and real-life experimental results show that our packed malware variants detection technique is comparable with the the state-of-art methods in terms of accuracy.Our approach can achieve more than 95.6\%of detection accuracy and 0.048 s of classification time cost.