Evaluation of the seismic behavior of reinforced concrete structures with flat slab-column gravity frame and shear walls through nonlinear analysis methods

This paper presents an investigation of the seismic behavior of reinforced concrete(RC)structures in which shear walls are the main lateral load-resisting elements and the participation of flat slab floor systems is not considered in the seismic design procedure.In this regard,the behavior of six prototype structures(with different heights and plan layouts)is investigated through nonlinear static and time history analyses,implemented in the OpenSees platform.The results of the analyses are presented in terms of the behavior of the slab-column connections and their mode of failure at different loading stages.Moreover,the global response of the buildings is discussed in terms of some parameters,such as lateral overstrength due to the gravity flat slab-column frames.According to the nonlinear static analyses,in structures in which the slab-column connections were designed only for gravity loads,the slab-column connections exhibited a punching mode of failure even in the early stages of loading.However,the punching failure was eliminated in structures in which a minimum transverse reinforcement recommended in ACI 318(2019)was provided in the slabs at joint regions.Furthermore,despite neglecting the contribution of gravity flat slab-column frames in the lateral load resistance of the structures,a relatively significant overstrength was imposed on the structures by the gravity frames.

Shaking table test and numerical analysis of a 1:12 scale model of a special concentrically braced steel frame with pinned connections

This paper describes shaking table tests of a 1：12 scale model of a special concentrically braced steel frame with pinned connections, which was fabricated according to a one-bay braced frame selected from a typical main factory building of a large thermal power plant. In order to investigate the seismic performance of this type of structure, several ground motion accelerations with different levels for seismic intensity Ⅷ, based on the Chinese Code for Seismic Design of Buildings, were selected to excite the model. The results show that the design methods of the members and the connections are adequate and that the structural system will perform well in regions of high seismicity. In addition to the tests, numerical simulations were also conducted and the results showed good agreement with the test results. Thus, the numerical model is shown to be accurate and the beam element can be used to model this structural system.

Pushover analysis of reinforced concrete frames considering shear failure at beam-column joints

Since most current seismic capacity evaluations of reinforced concrete （RC） frame structures are implemented by either static pushover analysis （PA） or dynamic time history analysis, with diverse settings of the plastic hinges （PHs） on such main structural components as columns, beams and walls, the complex behavior of shear failure at beam-column joints （BCJs） during major earthquakes is commonly neglected. This study proposes new nonlinear PA procedures that consider shear failure at BCJs and seek to assess the actual damage to RC structures. Based on the specifications of FEMA-356, a simplified joint model composed of two nonlinear cross struts placed diagonally over the location of the plastic hinge is established, allowing a sophisticated PA to be performed. To verify the validity of this method, the analytical results for the capacity curves and the failure mechanism derived from three different full-size RC frames are compared with the experimental measurements. By considering shear failure at BCJs, the proposed nonlinear analytical procedures can be used to estimate the structural behavior of RC frames, including seismic capacity and the progressive failure sequence of joints, in a precise and effective manner.

A New Rational-based Optimal Design Strategy of Ship Structure Based on Multi-level Analysis and Super-element Modeling Method

A new multi-level analysis method of introducing the super-element modeling method, derived from the multi-level analysis method first proposed by O. F. Hughes, has been proposed in this paper to solve the problem of high time cost in adopting a rational-based optimal design method for ship structural design. Furthermore,the method was verified by its effective application in optimization of the mid-ship section of a container ship. A full 3-D FEM model of a ship,suffering static and quasi-static loads, was used as the analyzing object for evaluating the structural performance of the mid-ship module, including static strength and buckling performance. Research results reveal that this new method could substantially reduce the computational cost of the rational-based optimization problem without decreasing its accuracy, which increases the feasibility and economic efficiency of using a rational-based optimal design method in ship structural design.

Nonlinear Stability Analysis of Long Span Continuous Rigid Frame Bridge with Thin Wall High Piers

By utilizing the current finite element program ANSYS, two types of finite element models (FEM), the beam model (BM) and shell model (SM), are established for the nonlinear stability analysis of a practical rigid frame bridge—Longtanhe Great Bridge. In these analyses, geometrical and material nonlinearities are simultaneously taken into account. For geometrical nonlinearity, updated Lagrangian formulations are adopted to derive the tangent stiffness matrix. In order to simulate the nonlinear behavior of the plastic hinge of the piers, the multi lines spring element COMBIN39 is used in the SM while the bilinear rotational spring element COMBIN40 is employed in the BM. Numerical calculations show that satisfying results can be obtained in the stability analysis of the bridge when the double coupling nonlinearity effects are considered. In addition, the conclusion is significant for practical engineering.

Method of reverberation ray matrix for static analysis of planar framed structures composed of anisotropic Timoshenko beam members

Based on the method of reverberation ray matrix（MRRM）, a reverberation matrix for planar framed structures composed of anisotropic Timoshenko（T） beam members containing completely hinged joints is developed for static analysis of such structures.In the MRRM for dynamic analysis, amplitudes of arriving and departing waves for joints are chosen as unknown quantities. However, for the present case of static analysis, displacements and rotational angles at the ends of each beam member are directly considered as unknown quantities. The expressions for stiffness matrices for anisotropic beam members are developed. A corresponding reverberation matrix is derived analytically for exact and unified determination on the displacements and internal forces at both ends of each member and arbitrary cross sectional locations in the structure. Numerical examples are given and compared with the finite element method（FEM） results to validate the present model. The characteristic parameter analysis is performed to demonstrate accuracy of the present model with the T beam theory in contrast with errors in the usual model based on the Euler-Bernoulli（EB） beam theory. The resulting reverberation matrix can be used for exact calculation of anisotropic framed structures as well as for parameter analysis of geometrical and material properties of the framed structures.

Structural failure analysis with CMS-based ground motion selection using innovative cost function and weight factors

The selection and scaling of ground motion records is considered a primary and essential task in performing structural analysis and design.Conventional methods involve using ground motion models and a conditional spectrum to select ground motion records based on the target spectrum.This research demonstrates the influence of adopting different weighted factors for various period ranges during matching selected ground motions with the target hazard spectrum.The event data from the Next Generation Attenuation West 2(NGA-West 2)database is used as the basis for ground motion selection,and hazard de-aggregation is conducted to estimate the event parameters of interest,which are then used to construct the target intensity measure(IM).The target IMs are then used to select ground motion records with different weighted vector-valued objective functions.The weights are altered to account for the relative importance of IM in accordance with the structural analysis application of steel moment resisting frame(SMRF)buildings.Instead of an ordinary objective function for the matching spectrum,a novel model is introduced and compared with the conventional cost function.The results indicate that when applying the new cost function for ground motion selection,it places higher demands on structures compared to the conventional cost function.Moreover,submitting more weights to the first-mode period of structures increases engineering demand parameters.Findings demonstrate that weight factors allocated to different period ranges can successfully account for period elongation and higher mode effects.

Nonlinear pushover analysis of infilled concrete frames

Six reinforced concrete frames with or without masonry infills were constructed and tested under horizontal cyclic loads. All six frames had identical details in which the transverse reinforcement in columns was provided by rectangular hoops that did not meet current ACI specifications for ductile frames. For comparison purposes, the columns in three of these frames were jacketed by carbon-fiber-reinforced-polymer （CFRP） sheets to avoid possible shear failure. A nonlinear pushover analysis, in which the force-deformation relationships of individual elements were developed based on ACI 318, FEMA 356, and Chen＇s model, was carried out for these frames and compared to test results. Both the failure mechanisms and impact of infills on the behaviors of these frames were examined in the study. Conclusions from the present analysis provide structural engineers with valuable information for evaluation and design of infilled concrete frame building structures.

Elastoplastic analysis of knee bracing frame

The knee bracing steel frame (KBF) is a new kind of energy dissipating frame, which combines excellent ductility and lateral stiffness. As the structural fuse of the frame, the knee element will yield first during a severe earthquake so that no damage occurs to the major structural members and the rehabilitation is easy and economical. To help fully understand the relations be- tween its seismic performance and the structural parameters, systematic elastoplastic analysis of the KBF structure with finite element method was conducted in this work. Finally, general design recommendations were made according to the results of the analysis.

Light weight analysis of a skeleton vehicle frame using BS960 super-high-strength steel

Static strength finite element analysis was conducted to decrease the weight of a skeleton vehicle＇s frame. Results indicated that the maximum stress occurs on the front beam ＇s variable section area. Dynamic sensitivity analysis elucidated the relationship between the maximum stress and the thickness of a particular beam,e. g.,top,middle,and bottom beam. Displacement was analyzed by the key part that influenced the maximum stress. Finally,the new plan using BS960 super-high-strength beam steel and the preferred beam thickness was compared with the original plan. New combinations of beam thickness were introduced on the basis of different purposes; the maximum responding light w eight ratio was 21%.

Nonlinear Time History Analysis for the Different Column Orientations under Seismic Wave Synthetic Approach

The significant impact of earthquakes on human lives and the built environment underscores the extensive human and economic losses caused by structural collapses. Over the years, researchers have focused on improving seismic design to mitigate earthquake-induced damages and enhance structural performance. In this study, a specific reinforced concrete (RC) frame structure at Kyungpook National University, designed for educational purposes, is analyzed as a representative case. Utilizing SAP 2000, the research conducts a nonlinear time history analysis to assess the structural performance under seismic conditions. The primary objective is to evaluate the influence of different column section designs, while maintaining identical column section areas, on structural behavior. The study employs two distinct seismic waves from Abeno (ABN) and Takatori (TKT) for the analysis, comparing the structural performance under varying seismic conditions. Key aspects examined include displacement, base shear force, base moment, joint radians, and layer displacement angle. This research is anticipated to serve as a valuable reference for seismic restraint reinforcement work on RC buildings, enriching the methods used for evaluating structures through nonlinear time history analysis based on the synthetic seismic wave approach.

Seismic analysis of long-span continuous rigid frame bridges in cold regions:a case study of Bridge 1 in north of international tourism resort in Changbai Mountain

It is helpful to improve the seismic design theory of long-span continuous bridges for studying the seismic performance of each cantilever construction state.Taking the Bridge 1 in the north of Changbai-Mountain international tourism resort as an example,the authors studied it in shutdown phase and the cantilever construction process,established the simulation model by using Midas / civil,and analyzed time-history of each construction stage for the bridge.The study shows that long-span bridge cantilever construction in northeastern China can be divided into two-year tasks for construction(suspending in winter).It is needed to think about seismic stability of the cantilever position in shut-down phase of winter.The effect of longitudinal vibration is the most disadvantageous influence to bridge,and its calculation results can provide reference for seismic design of similar bridges in the future.

A Framework for Web-Based Mechanical Design and Analysis

In this paper, a Web-based Mechanical Design and A na lysis Framework (WMDAF) is proposed. This WMADF allows designers to develop web -based computer aided programs in a systematic way during the collaborative mec hanical system design and analysis process. This system is based on an emerg ing web-based Content Management System (CMS) called eXtended Object Oriented P ortal System (XOOPS). Due to the Open Source Status of the XOOPS CMS, programs d eveloped with this framework can be further customized to satisfy the demands of the user. To introduce the use of this framework, this paper exams three differ ent types of mechanical design and analysis problems. First, a repetitive design consideration and calculation process is transferred into WMADF programs to gai n efficiency for wired collaborative team. Second, the considered product solid model is created directly through the use of XOOPS program and Microsoft Compone nt Object Model (COM) instances. To the end of the paper, an example linked with ANSYS is used to indicate the possible application of this framework.

A Calibration Method of Robot Base Frame with Procrustes Analysis

In order to realize high precision industrial operations,based on the POE formula,an effective approach to calibrate the robot's actual base frame(ABF) is proposed. Due to the existence of manufacturing errors,the ABF deviates slightly from nominal base frame( NBF). Using external precision measurement,the ABF can be established only through the three dimension(3D) position of the robot's end-effector.To ensure the orthonormal constraints of rotation matrix as well as the precise solutions,Procrustes Analysis is introduced,where an optimal orthogonal matrix is solved out by the Lagrange Multiplier method and Singular Value Decomposition(SVD). Furthermore,calibration experiment on a serial 6-DOF robot is performed,where a FARO laser tracker is utilized to measure the 3D position. Finally, calibration result indicates that the positioning accuracy has been significantly improved after calibration. The calibration method is also applicable to other similar problems,such as multi-robot coordination and robot hand-eye system calibration.

Static and Vibration Analysis of an Aluminium and Steel Bus Frame

The transport sector is increasing day by day to satisfy the global market requirement. The bus is still the main mode of intercity transportation in Canada. Despite, an essentially unchanged conception, the total weight of the bus has increased by over 25% during the last three decades. To solve this problem, industrialists have moved to the use of light metals in the transportation field. Therefore, use of lightweight materials, such as aluminum is essential to reduce the total weight of bus. In this study, the focus is on the bus frame as it represents 30% of the total weight and it is the most stressed part of the bus. Its life duration is more important compared to that of all other elements. Thus, a study of the static and vibratory behavior would be very decisive. In this article, two types of analysis are carried out. First is the modal analysis to determine the natural frequencies and the mode shapes using a developed dynamic model of the bus. Because if any of the excitation frequencies coincides with the natural frequencies of the bus frame, then resonance phenomenon occurs. This may lead to excessive deflection, high stress concentration, fatigue of the structure and vehicle discomfort. In this case, the results analysis shows that the natural frequencies are not affected by the change of material. The second type of analysis is the linear static stress analysis to consider the stress distribution and deformation frame pattern under static loads numerically. For the numerical method, the frame is designed using SolidWorks and the analysis is made using Ansys WorkBench. The maximum Von Mises stress obtained for the static loading is in the same order for the three chassis frames studied. But in the case of the aluminium frame, the weight of 764 kg was reduced.

Performance Analysis of Frame Aggregation under Unsaturated Conditions

This paper proposes an analysis model of frame aggregation in error-free channel with unsaturated traffic and fixed aggregation size. Integrated with model of channel access, calculation of MAC (Media Access Control) average service time and queue model of frame aggregation, our model can get the stable result with a recursive algorithm, and it further derive the throughput and latency of frame aggregation in steady state. As the impact of traffic, frame length, collision probability, buffer size, aggregation size and interactive effects are taken into consideration, the effect of every parameter could be evaluated and the major factor which degrades the performance of frame aggregation can be determined in different situation with this model. By the simulation and numerical analysis, this model confirmed its accuracy. The proposed model can be used in the design, optimization and deployment of WLAN (Wireless Local Area Network) and WMN (Wireless Mesh Network) widely.

Modal Correlation Based Analysis on Dynamic Characters of a Commercial Semi-Trailer's Chassis Frames

In order to evaluate two different schemes＇ structural dynamic characters, dynamic response analysis of a commercial truck＇s main chassis frames is carried out. On the basis of correlation study between the tested and calculated modal results, the assembled frames＇ finite element analysis （FEA） models with sufficient precision are built up. Random response analysis in frequency domain is carried out with these FEA models, RMS values of yon Mises and main principle stresses of these two frames are obtained. It shows that the analysis resuits of the distributing tendency and concrete value ranges are coincident very well with test results. And from the results, it could be concluded that frames of scheme A endures relative better loading conditions and should be adopted as the final scheme.

Compressed data separation via dual frames based split-analysis with Weibull matrices

In this paper, we consider data separation problem, where the original signal is composed of two distinct subcomponents, via dual frames based Split-analysis approach. We show that the two distinct subcomponents, which are sparse in two diff erent general frames respectively, can be exactly recovered with high probability, when the measurement matrix is a Weibull random matrix （not Gaussian） and the two frames satisfy a mutual coherence property. Our result may be significant for analysing Split-analysis model for data separation.

FRAME MULTIRESOLUTION ANALYSIS AND INFINITE TREES IN BANACH SPACES ON LOCALLY COMPACT ABELIAN GROUPS

We extend the concept of frame multiresolution analysis to a locally compact abelian group and use it to define certain weighted Banach spaces and the spaces of their antifunctionals. We define analysis and synthesis operators on these spaces and establish the continuity of their composition. Also, we prove a general result to characterize infinite trees in the above Banach spaces of antifunctionals. This paper paves the way for the study of corresponding problems associated with some other types of Banach spaces on locally compact abelian groups including modulation spaces.

Fatigue Strength and Modal Analysis of Bogie Frame for DMUs Exported to Tunisia

The equivalent stress at key positions of Bogie Frame for DMUs Exported to Tunisia is obtained by using simulation analysis. The evaluation of static strength and fatigue strength is checked referring to UIC specification and Goodman sketch for welding materials. In addition, the modal analysis of the frame is made, and the vibrational modal of frame in given frequency domain is predetermined to evaluate the dynamical behavior of the frame in order to meet the dynamical design requirements. The results show that the key points of the calculated frame of the equivalent stress are less than allowable stress, and thus it could provide a theoretical foundation for the optimized design of frame structure and safety of industrial production.