A Modified Iterative Learning Control Approach for the Active Suppression of Rotor Vibration Induced by Coupled Unbalance and Misalignment

This paper proposes a modified iterative learning control(MILC)periodical feedback-feedforward algorithm to reduce the vibration of a rotor caused by coupled unbalance and parallel misalignment.The control of the vibration of the rotor is provided by an active magnetic actuator(AMA).The iterative gain of the MILC algorithm here presented has a self-adjustment based on the magnitude of the vibration.Notch filters are adopted to extract the synchronous(1×Ω)and twice rotational frequency(2×Ω)components of the rotor vibration.Both the notch frequency of the filter and the size of feedforward storage used during the experiment have a real-time adaptation to the rotational speed.The method proposed in this work can provide effective suppression of the vibration of the rotor in case of sudden changes or fluctuations of the rotor speed.Simulations and experiments using the MILC algorithm proposed here are carried out and give evidence to the feasibility and robustness of the technique proposed.

An active high-static-low-dynamic-stiffness vibration isolator with adjustable buckling beams:theory and experiment

High-static-low-dynamic-stiffness(HSLDS)vibration isolators with buckling beams have been widely used to isolate external vibrations.An active adjustable device composed of proportion integration(PI)active controllers and piezoelectric actuators is proposed for improving the negative stiffness stroke of buckling beams.A nonlinear output frequency response function is used to analyze the effect of the vibration reduction.The prototype of the active HSLDS device is built,and the verification experiment is conducted.The results show that compared with the traditional HSLDS vibration isolator,the active HSLDS device can broaden the isolation frequency bandwidth,and effectively reduce the resonant amplitude by adjusting the active control parameters.The maximum vibration reduction rate of the active HSLDS vibration isolator can attain 89.9%,and the resonant frequency can be reduced from 31.08 Hz to 13.28 Hz.Therefore,this paper devotes to providing a new design scheme for enhanced HSLDS vibration isolators.

Active Vibration Control of Beam Using Electro-magnetic Constrained Layer Damping

This paper investigates vibration control of beam through electro-magnetic constrained layer damping （EMCLD） which consists of electromagnet layer, permanent magnet layer and viscoelastic damping layer. When the coil of the electromagnet is electrified with proper control strategy, the electromagnet can exert magnetic force opposite to the direction of structural deformation so that the structural vibration is attenuated. A mathematical model is developed based on the equivalent current method to calculate the electromagnetic control force produced by EMCLD. The governing equations of the system are obtained using Hamilton＇s Principle and then reduced with the assumed-mode method. A simulation on vibration control of a cantilever beam is conducted under the velocity proportional feedback to demonstrate the energy dissipation capability of EMCLD, and the beam system with the same parameter is experimented. The results of experiment and simulation are compared and the results show that the EMCLD is an effective means for suppressing modal vibration. The results also indicate that the beam system has better control performance for larger control current. The EMCLD method presented in this paper provides an applicable and efficient tool for the vibration control of structures.

VIBRATION CONTROL OF A SPACE TRUSS STRUCTURE WITH A PIEZOELECTRIC ACTIVE MEMBER

Active vibration control is an effective way of increasing robustness of the design to meet the stringent accuracy requirements for space structures. This paper presents the results of active damping realized by a piezoelectric active member to control the vibration of a four-bay four-longern aluminum truss structure with cantilever boundary. The active member, which utilizes a piezoelectric actuating unit and an integrated load cell, is designed for vibration control of the space truss structures. Active damping control is realized using direct velocity feedback around the active member. The placement of the active member as one of the most important factor of affecting the control system performance, is also investigated by modal dissipation energy ratio as indicator. The active damping effectiveness is evaluated by comparing the closed-loop response with the open loop response.

SEMI ACTIVE VIBRATION CONTROL BASED ON A VIBRATION ABSORBER WITH ADJUSTABLE CLEARANCE

Presented in this paper is a semi active vibration control strategy based on the vibration absorber with adjustable clearance in elastic component. The control law of the clearance for alleviating the vibration of primary system is derived by means of harmonic balancing technique so that the working frequency of the vibration absorber can trace the frequency variation of the harmonic excitation. The efficacy of the strategy is demonstrated by numerical simulations for attenuating the steady state vibration of a SDOF system and a 2 DOF system, which are under the harmonic excitation with slowly varied frequency in a wide range.

Experimental Investigation on Vibration Control of Rotor-bearing System with Active Magnetic Exciter

Vibration control is an efficient way to minimize a rotating machine’s vibration level so that its vibration fault-free can be realized.While,several factors,such as unbalance,misalignment and instability,contribute to the serious vibration of rotating machines.It is necessary that one apparatus can depress vibration caused by two or more reasons.The fault self-recovery(FSR) mechanism is introduced and investigated.Strategies of vibration control are investigated theoretically using numerical method firstly.Active magneticelectric exciter(AME) are selected as the actuator of a FSR device because it can provide suitable force by varying the control current in the exciters depending upon a proportional and derivative control law.By numerical study,it is indicate that only a small control force is needed to improve stability margins of the compressor and prevent subsynchronous vibration fault efficiently.About synchronous vibration,three control strategies,searching in whole circle,fast optimizing control(FOC),and none mistaking control,are investigated to show which of the control strategy can realize the fault self-recovery in the shortest time.Experimental study is conducted on a test rig with variable rotating speed.Results of the test indicate that the non-mistake control strategy can minimize synchronous vibration in less than three seconds.The proposed research can provide a new insight for subsynchronous and synchronous vibration restraining about centrifugal compressor.

Optimal Active Control of Wave-Induced Vibration for Offshore Platforms

An obvious motivation of this paper is to examine the effectiveness of the lateral vibration control of a jacket type offshore platform with an AMD control device, in conjunction with H-2 control algorithm, which is an optimal frequency domain control method based on minimization of H-2 norm of the system transfer function In this study, the offshore platform is modeled numerically by use of the finite element method, instead of a lumped mass model This structural model is later simplified to be single-degree-of-freedom (SDOF) system by extracting the first vibration mode of the structure. The corresponding 'generalized' wave force is determined based on an analytical approximation of the first mode shape function, the physical wave loading being calculated from the linearized Morison equation. This approach facilitates the filter design for the generalized force. Furthermore, the present paper also intends to make numerical comparison between H-2 active control and the corresponding passive control using a TMD with the same device parameters.

Research of an Active Tunable Vibration Absorber for Helicopter Vibration Control

Significant structural vibration is an undesirable characteristic in helicopter flight that leads to structural fatigue, poor ride quality for passengers and high acoustic signature. Previous Individual Blade Control (IBC) techniques to reduce these effects have been hindered by electromechanical limitations of piezoelectric actuators. The Smart Spring is an active tunable vibration absorber using IBC approach to adaptively alter the 'structural impedance' at the blade root. In this paper, a mathematical model was developed to predict the response under harmonic excitations. An adaptive notch algorithm was designed and implemented on a TMS320c40 DSP platform. Reference signal synthesis techniques were used to automatically track the shifts in the fundamental vibratory frequency due to variations in flight conditions. Closed-loop tests performed on the proof-of-concept hardware achieved significant vibration suppression at harmonic peaks as well as the broadband reduction in vibration. The investigation verified the capability of the Smart Spring to suppress multiple harmonic components in blade vibration through active impedance control.

A hybrid multi-degree-of-freedom vibration isolation platform for spacecrafts by the linear active disturbance rejection control

The hybrid vibration isolation, which takes advantages of both the passive and active approaches, has been an important solution for space missions. The objective of this paper is to design a vibration isolation platform for payloads on spacecrafts with the robust, wide bandwidth, and multi-degree-of-freedom(MDOF). The proposed solution is based on a parallel mechanism with six voice-coil motors(VCMs) as the actuators. The linear active disturbance resistance control(LADRC) algorithm is used for the active control. Numerical simulation results show that the vibration isolation platform performs effectively over a wide bandwidth, and the resonance introduced by the passive isolation is eliminated. The system robustness to the uncertainties of the structure is also verified by simulation.

Novel approach for active vibration control of a flexible missile

This paper investigates the feasibility of using an active dynamic vibration absorber(ADVA) for active vibration control of a flexible missile system through simulation.Based on the principles of a dynamic vibration absorber(DVA),a ring-type ADVA is first designed to attenuate the elastic vibration of the flexible missile,and the design of the active controller adopts the proportional-integral-derivative(PID)control algorithm.The motion equations of a flexible missile with an ADVA,which is subjected to follower thrust at its aft end,are derived using the Lagrangian approach.Taking the minimum of the root mean square(RMS) of the lateral displacement response of the center of mass as the objective function,a genetic algorithm(GA) is used to optimize the parameter of the DVA and PID controller.The numerical calculations show that the ADVA and DVA are effective in suppressing the vibration and provide approximately 41.2% and 17.6% improvement,respectively,compa red with the case of no DVA,The ADVA has better performance than the DVA,When the missile is subjected to follower thrust,the effect of vibration reduction is more effective than the case without follower thrust.It is feasible to reduce vibration and improve the stability of flexible missiles by means of the ADVA.

Vibration analysis and active control of nearly periodic two-span beams with piezoelectric actuator/sensor pairs

The piezoelectric materials are used to investigate the active vibration control of ordered/disordered periodic two-span beams. The equation of motion of each sub-beam with piezoelectric patches is established based on Hamilton＇s principle with an assumed mode method. The velocity feedback control algorithm is used to design the controller. The free and forced vibration behaviors of the two-span beams with the piezoelectric actuators and sensors are analyzed. The vibration properties of the disordered two-span beams caused by misplacing the middle support are also researched. In addition, the effects of the length disorder degree on the vibration performances of the disordered beams are investigated. From the numerical results, it can be concluded that the disorder in the length of the periodic two-span beams will cause vibration localizations of the free and forced vibrations of the structure, and the vibration localization phenomenon will be more and more obvious when the length difference between the two sub-beams increases. Moreover, when the velocity feedback control is used, both the forced and the free vibrations will be suppressed. Meanwhile, the vibration behaviors of the two-span beam are tuned.

INVESTIGATION OF SIMULATION EXPERIMENT ON ACTIVE CONTROL OF TORSIONAL VIBRATION IN A TURBOGENERATOR SHAFT SYSTEM

According to the theoretical analysis and calculation on the base ofcontinuous mass system, the simulation experimental investigation on active control of torsionalvibration in a turbogenerator shaft system is conducted. A test installation with the excitation ofgenerator motor and multi-stepped shaft system is established to simulate the torsional vibration ofa turbogenerator rotor shaft system, and to examine the active control strategy presented. Someuseful results are reached in the experimental study.

Hybrid Passive/Active Vibration Control of a Loosely Connected Spacecraft System

In this paper,a hybrid passive/active vibration(HPAV)controller of a loosely connected spacecraft consisting of a servicing satellite,a target and an X-shape structure isolator is first proposed to suppress vibrations of the system when subjected to the impulsive external excitations during the on-orbit missions.The passive dynamic response of the combined system can be adjusted appropriately to achieve the desired vibration isolation performance by tuning the structural parameters of the bio-inspired X-shape structure.Moreover,the adaptive control design through dynamic scaling technique is selected as the active component to maintain high vibration isolation performance in the presence of parameter uncertainties such as mass of the satellite platform,the damping and rotation friction coefficients of the X-shape structure.Compared with the pure passive system and the traditional spring-mass-damper(SMD)isolator,the HPAV strategy witnesses lower transmissibility,smaller vibration amplitude and higher convergence rate when subjected to the post-capture impact.Numerical simulations demonstrate the feasibility and validity of the proposed hybrid control scheme in suppressing vibrations of the free-floating spacecraft.

Experimental Study on Magnetorheological Damper for Semi-Active Vibration Control of Civil Infrastructures

Magnetorheological (MR) fluid is a kind of smart material whose rheological properties can be rapidly varied in magnetic field. To make full use of the advantages of MR fluid to devices, a model of double ended, shear combined and valve typed MR damper is designed and manufactured, and the dynamic properties under sinusoidal excitations are experimentally studied. The experiment results show that the maximum damping force of the MR damper at the full magnetic intensity reaches about 20 kN while the maximum power required is less than 50 W, which predicts that the MR damper will be a powerful measurement for semi active vibration control of civil infrastructures.

Anti-Dead-Zone Integral Sliding Control and Active Vibration Suppression of a Free-floating Space Robot with Elastic Base and Flexible Links

Under the conditions of joint torque output dead-zone and external disturbance,the trajectory tracking and vibration suppression for a free-floating space robot(FFSR)system with elastic base and flexible links were discussed.First,using the Lagrange equation of the second kind,the dynamic model of the system was derived.Second,utilizing singular perturbation theory,a slow subsystem describing the rigid motion and a fast subsystem corresponding to flexible vibration were obtained.For the slow subsystem,when the width of deadzone is uncertain,a dead-zone pre-compensator was designed to eliminate the impact of joint torque output dead-zone,and an integral sliding mode neural network control was proposed.The integral sliding mode term can reduce the steady state error.For the fast subsystem,an optimal linear quadratic regulator(LQR)controller was adopted to damp out the vibration of the flexible links and elastic base simultaneously.Finally,computer simulations show the effectiveness of the compound control method.

PI force feedback control for large flexible structure vibration with active tendons

Active tendon, consisting of a displacement actuator and a collocated force sensor, was first presented by Preumont and his co-workers to attenuate the vibration of large flexible space structures, and the control algorithm adopted by them was integral force feedback. This paper presents a new proportional-integral （PI） force feedback algorithm to achieve larger damping ratios for the structure without the requirement of structure model. Stability of the control system is shown, and simulations of a structure similar to JPL-MPI demonstrate the effectiveness of the proposed algorithm for vibration control of space structures.

DESIGN AND ANALYSIS OF NOVEL ACTIVE ACTUATOR TO CONTROL LOW FREQUENCY VIBRATIONS OF SHAFT SYSTEM

Aiming at providing with high-load capability in active vibration control of large-scale rotor system, a new type of active actuator to simultaneously reduce the dangers of low frequency flexural and torsional vibrations is designed. The actuator employs electro-hydraulic system and can provide a high and circumferential load. To initialize new research, the characteristics of various kinds of active actuators to control rotor shaft vibration are briefly introduced. The purpose of this paper is to introduce the preliminary results via presenting the structure, functions and operating principles, in particular, the working process of the electro-hydraulic system of the new actuator which includes a set of high speed electromagnetic valves and a series of sloping cone-shaped openings, and presenting the transmission relationships among the control parameters from control signals into the valves to active load onto shaft. The course of the work is dynamic, and a series of spatial forces and moments are put on the shaft to get an external resultant force to reduce excitations that induce vibration of shafts. By checking states of vibration, the actuator can control the impulse width and the interval of injection time for applying different control force to a vibration shaft in two circumference directions through the regulating action of a set of combination directional control valves. The results from simulating analysis and experiment show evidence of that this design can satisfy the case of active process of decreasing of flexural and torsional vibrations.

VIBRATION CONTROL OF FLUID-FILLED PRISMATIC SHELL WITH ACTIVE CONSTRAINED LAYER DAMPING TREATMENTS

Active constrained layer damping （ACLD） combines the simplicity and reliability of passive damping with the light weight and high efficiency of active actuators to obtain high damping over a wide frequency band. A fluid-filled prismatic shell is set up to investigate the validity and efficiency of ACLD treatments in the case of fluid-structure interaction. By using state subspace identification method, modal parameters of the ACLD system are identified and a state space model is established subsequently for the design of active control laws. Experiments are conducted to the fluid-filled prismatic shell subjected to random and impulse excitation, respectively, For comparison, the shell model without fluid interaction is experimented as well. Experimental results have shown that the ACLD treatments can suppress vibration of the fluid-free and fluid-filled prismatic shell effectively. Under the same control gain, vibration attenuation is almost the same in both cases.

Real-time Design Constraints in Implementing Active Vibration Control Algorithms

Although computer architectures incorporate fast processing hardware resources, high performance real-time implementation of a complex control algorithm requires an efficient design and software coding of the algorithm so as to exploit special features of the hardware and avoid associated architecture shortcomings. This paper presents an investigation into the analysis and design mechanisms that will lead to reduction in the execution time in implementing real-time control algorithms. The proposed mechanisms are exemplified by means of one algorithm, which demonstrates their applicability to real-time applications. An active vibration control （AVC） algorithm for a flexible beam system simulated using the finite difference （FD） method is considered to demonstrate the effectiveness of the proposed methods. A comparative performance evaluation of the proposed design mechanisms is presented and discussed through a set of experiments.

ACTIVE VIBRATION CONTROL AND SUPPRESSION FOR INTEGRATED STRUCTURES

The finite element dynamic model for integrated structures containing distributed piezoelectric sensors and actuators ( S/As ) is formulated with a new piezoelectric plate bending element in this paper. The problem of active vibration control and suppression of integrated structures is investigated under constant gain negative velocity feedback control law. A general method for active vibration control and suppression of integrated structures is presented. Finally, numerical example is given to illustrate the validity of the method proposed in this paper.