Optimization Control of Multi-Mode Coupling All-Wheel Drive System for Hybrid Vehicle

The all-wheel drive(AWD)hybrid system is a research focus on high-performance new energy vehicles that can meet the demands of dynamic performance and passing ability.Simultaneous optimization of the power and economy of hybrid vehicles becomes an issue.A unique multi-mode coupling(MMC)AWD hybrid system is presented to realize the distributed and centralized driving of the front and rear axles to achieve vectored distribution and full utilization of the system power between the axles of vehicles.Based on the parameters of the benchmarking model of a hybrid vehicle,the best model-predictive control-based energy management strategy is proposed.First,the drive system model was built after the analysis of the MMC-AWD’s drive modes.Next,three fundamental strategies were established to address power distribution adjustment and battery SOC maintenance when the SOC changed,which was followed by the design of a road driving force observer.Then,the energy consumption rate in the average time domain was processed before designing the minimum fuel consumption controller based on the equivalent fuel consumption coefficient.Finally,the advantage of the MMC-AWD was confirmed by comparison with the dynamic performance and economy of the BYD Song PLUS DMI-AWD.The findings indicate that,in comparison to the comparative hybrid system at road adhesion coefficients of 0.8 and 0.6,the MMC-AWD’s capacity to accelerate increases by 5.26%and 7.92%,respectively.When the road adhesion coefficient is 0.8,0.6,and 0.4,the maximum climbing ability increases by 14.22%,12.88%,and 4.55%,respectively.As a result,the dynamic performance is greatly enhanced,and the fuel savings rate per 100 km of mileage reaches 12.06%,which is also very economical.The proposed control strategies for the new hybrid AWD vehicle can optimize the power and economy simultaneously.

Fake News Detection Based on Text-Modal Dominance and Fusing Multiple Multi-Model Clues

In recent years,how to efficiently and accurately identify multi-model fake news has become more challenging.First,multi-model data provides more evidence but not all are equally important.Secondly,social structure information has proven to be effective in fake news detection and how to combine it while reducing the noise information is critical.Unfortunately,existing approaches fail to handle these problems.This paper proposes a multi-model fake news detection framework based on Tex-modal Dominance and fusing Multiple Multi-model Cues(TD-MMC),which utilizes three valuable multi-model clues:text-model importance,text-image complementary,and text-image inconsistency.TD-MMC is dominated by textural content and assisted by image information while using social network information to enhance text representation.To reduce the irrelevant social structure’s information interference,we use a unidirectional cross-modal attention mechanism to selectively learn the social structure’s features.A cross-modal attention mechanism is adopted to obtain text-image cross-modal features while retaining textual features to reduce the loss of important information.In addition,TD-MMC employs a new multi-model loss to improve the model’s generalization ability.Extensive experiments have been conducted on two public real-world English and Chinese datasets,and the results show that our proposed model outperforms the state-of-the-art methods on classification evaluation metrics.

考虑PWM波形特征的纳米晶磁心损耗模型的研究及验证

磁心损耗精确预测对于电力电子变压器的优化设计至关重要。然而,传统的磁心损耗模型在复杂激励下适用性较差,尤其对于占空比可调、高次谐波含量丰富的PWM波磁心损耗预测,计算精度显著下降。基于Jordan损耗分离模型,建立了一种考虑PWM波形特征的磁心损耗计算方法。首先,该方法根据激励波形特征,推导出相应的波形系数及等效频率来计算PWM波激励下的动态涡流损耗,将Jordan模型的适用范围从正弦拓展到PWM波激励下的磁心损耗计算;然后,分析了不同占空比激励下激励波形有效频率及高次谐波含量变化对损耗系数的影响,并对其进行数学表征,实现了整个占空比范围内磁心损耗的精确预测;最后,搭建了高频非正弦激励下软磁材料磁特性测量平台,针对1K107B纳米晶材料,测量了两种典型PWM波激励下的损耗数据。实验结果表明,所建立的磁心损耗模型具有较高的计算精度,相比于传统的Steinmetz改进公式,整体精度提高了25%。

Time varying congestion pricing for multi-class and multi-mode transportation system with asymmetric cost functions

This paper considers the problem of time varying congestion pricing to determine optimal time-varying tolls at peak periods for a queuing network with the interactions between buses and private cars.Through the combined applications of the space-time expanded network（STEN） and the conventional network equilibrium modeling techniques,a multi-class,multi-mode and multi-criteria traffic network equilibrium model is developed.Travelers of different classes have distinctive value of times（VOTs）,and travelers from the same class perceive their travel disutility or generalized costs on a route according to different weights of travel time and travel costs.Moreover,the symmetric cost function model is extended to deal with the interactions between buses and private cars.It is found that there exists a uniform（anonymous） link toll pattern which can drive a multi-class,multi-mode and multi-criteria user equilibrium flow pattern to a system optimum when the system＇s objective function is measured in terms of money.It is also found that the marginal cost pricing models with a symmetric travel cost function do not reflect the interactions between traffic flows of different road sections,and the obtained congestion pricing toll is smaller than the real value.

一种低延时低功耗PWM比较器电路设计

设计了一种基于HHGrace 0.35μm BCD工艺的低延时低功耗电压型静态脉冲宽度调制(Pulse Width Modulation,PWM)比较器,主要应用于高频低功耗的开关电源系统。设计中包含动态尾电流源和改进型正反馈放大器,以改进传统跨导放大器(Operational Transconductance Amplifier,OTA)型比较器高延迟和高功耗等问题。仿真结果表明:在1.2~5.0 V供电电压范围内稳定工作,最大上升沿延时35 ns,最大下降沿延时41 ns,支持6 MHz开关频率的系统,比较精度8 mV,失调电压439μV,静态功耗仅为2.5μA(1.2 V供电)和4.4μA(5.0 V供电)。

不平衡电网下电流源型PWM整流器改进型无差拍控制

三相电流源型PWM整流器运行在电网电压不平衡情况下,引起直流侧及网侧电流存在大量低次谐波,势必对后级变换器供电稳定性、安全性等存在不利影响。针对该问题,首先建立整流器数学模型,推导出不平衡电网下直流侧电压和网侧电流表达式,揭示出系统直流侧和网侧电流产生低次谐波的机理。其次,根据瞬时功率理论设计内环电流参考指令,并利用无差拍控制实现网侧电流对参考电流的跟踪。然而传统无差拍控制存在延时问题,将影响网侧电流的跟随性能,造成电能质量下降。为解决该问题,提出了网侧电流内环改进型无差拍控制,利用两步预测法补偿系统延时。最后,基于Matlab/Simulink平台搭建仿真模型,验证所提控制策略的正确性与有效性。结果表明,所提方法能有效抑制直流侧和网侧电流低次谐波,实现网侧电流正弦化和直流侧电压稳定输出。

定频PWM控制混合桥双LLC谐振变换器研究

针对宽输出电压应用中传统频率控制LLC谐振变换器工作频率范围宽且存在较大循环电流的问题,提出1种定频PWM控制混合桥双LLC谐振变换器。根据原边侧结构的不同,所提变换器有3种拓扑结构形式,分别为半桥-半桥双LLC谐振变换器、半桥-全桥双LLC谐振变换器、全桥-全桥双LLC谐振变换器。其中,原边侧结构并联输入,2个变压器二次侧串联输出。相较于传统频率控制LLC变换器,3种拓扑形态始终在谐振频率点工作,缩小了开关频率范围;在PWM控制策略下,可以分别实现2倍电压增益、3倍电压增益和4倍电压增益以适应宽电压场合;电路中循环电流损耗低,软开关性能良好。Simulink仿真和实验结果验证了所提方案的可行性。

基于非线性扰动观测器的三相PWM整流器滑模控制

针对交流微电网中三相PWM整流器的运行状态易受负载扰动、滤波电容参数摄动影响的问题,本文提出一种基于非线性扰动观测器的三相PWM整流器滑模控制方法。首先,将负载扰动、滤波电容参数摄动等视为集总扰动,构建电压环非线性模型。其次,设计非线性扰动观测器,实现集总扰动的在线估计。为实现主动抗干扰控制和滑模抖振抑制,将估计的集总扰动引入到滑模面中,得到了一种含有扰动估计的新型滑模面。最后,基于滑模控制理论设计电压外环滑模控制器,并采用Lyapunov稳定性理论对其进行了稳定性证明。动态性能测试结果表明,非线性扰动观测器能够快速、准确地对集总扰动进行估计;与双环PI控制相比,所提控制的过渡过程时间减少了60%,电压跌落量减少了54%;滤波电容参数变化时,所提控制的动态性能保持良好。稳态性能测试结果表明,与传统滑模控制和双环PI控制相比,所提控制的电流总谐波畸变率分别减少了70%和44%,同时滑模抖振得到了有效地抑制。测试结果证明了所提控制方法的强抗负载扰动能力和良好的滤波电容参数鲁棒性。

大学英语的Multi-Mode教学模式

针对目前高职院校大学英语教学普遍存在的问题,结合全国性大学英语教学需要改革的迫切要求,笔者对所在院校研究并应用的Multi-Mode教学模式进行分析说明,其关键性在于培养学生自主学习的积极性,较好地落实教学任务,提高学生参加英语等级考试的通过率。

基于PWM软开关技术的智能充电机的设计与实现

针对由工频变压器和整流电路组成的传统充电机存在体积大、不便运输、可靠性差等缺陷,采用无工频变压器开关电源技术,按照蓄电池充电特性曲线特点,采用恒流-恒压(CC-CV)充电法,进行系统方案及主电路设计,并使用整流—Buck降压斩波模式和PWM软开关技术控制充电机电路。实验表明,与工频型充电机相比,该方法能显著延长蓄电池使用寿命。

基于三矢量的PWM整流器改进模型预测直接功率控制方法

为解决传统模型预测直接功率控制存在的开关频率不恒定、计算量大、共模电压大问题,设计了一种三矢量模型预测直接功率控制方法。该方法通过在单个控制周期内输出三个不同电压矢量,克服了传统方法因连续多个周期输出相同电压矢量造成的开关频率不恒定问题;同时,在两相静止坐标系中,通过优化空间电压矢量图划分方法,采用两个代价函数确定电网电压矢量所在扇区,将算法的遍历次数从27次降至10次,克服了传统方法计算量大的问题;此外,通过去除两个冗余零矢量PPP与NNN,将共模电压抑制在Udc/3以内。最后搭建了5kW实验样机进行实验验证,仿真与实验结果表明,该方法可以有效降低计算量,输出谐波和共模电压抑制效果优于传统方法。

3D FEM simulation of responses of LWD multi-mode resistivity imaging sonde

A new multi-mode resistivity imaging sonde, with toroidal coils as source, can conduct three resistivity measurements: azimuthal resistivity, lateral resistivity, and bit resistivity measurements. Thus, the logging time and cost are greatly saved. The toroidal coils are simplified as an extended voltage dipole and the response equations are derived for a homogenous formation. Based on 3D FEM, the depth of investigation(DOI), vertical resolution, circumferential azimuthal capacity, borehole diameter, mud resistivity, thickness of target formation, and the resistivity of the surrounding formation and mud invasion are simulated. The results suggest that the three measurement modes of the new sonde are different in vertical resolutions and DOIs. The circumferential detection ability of the azimuth button depends on the contrast between the anomaly and formation resistivity and the open angle of the anomaly. Whether the borehole is truncated at the bit or not has a great influence on the simulation results. The borehole and mud invasion affect the apparent resistivity in all modes, but the effects of resistivity of surrounding formation and thickness of the target formation are only corrected for lateral resistivity measurement.

一种基于离散时域模型的单相PWM整流器控制参数多目标优化设计方法

单相PWM整流器一般采用电压外环比例积分、电流内环比例谐振的双闭环控制方法,在实现交流侧高功率因数的同时稳定直流侧输出电压,因此受到国内外学者的广泛研究。然而,在内外环控制参数设计阶段,传统设计方法一般根据经验选取控制参数,参数选取范围较大,且无法量化评估控制参数的时域控制效果,导致参数优化整定困难。为此,该文提出一种基于离散时域模型的内外环控制参数多目标优化设计方法。首先,采用传统设计方法确定电压外环比例、积分控制参数以及电流内环比例、谐振控制参数的安全设计空间;然后,基于离散时域模型将安全设计空间正映射至控制参数的时域性能空间,实现电流内环控制参数对交流侧功率因数以及电压外环控制参数对直流侧电压超调量的量化评估。在此基础上,通过进一步约束性能目标得到性能优化设计空间,考虑内外环控制参数的耦合效应,对内外环性能优化设计空间进行重新组合,再将其映射至性能空间,得到内外环控制目标帕累托最优前沿下的最优设计空间,从中选取内外环控制参数的优化设计点,在典型工况下实验测得的交流侧功率因数为0.981 26,直流输出电压超调量绝对值为1.37%,证明了所提优化设计方法的正确性。

Signal classification method based on data mining formulti-mode radar

For the multi-mode radar working in the modern electronicbattlefield, different working states of one single radar areprone to being classified as multiple emitters when adoptingtraditional classification methods to process intercepted signals,which has a negative effect on signal classification. A classificationmethod based on spatial data mining is presented to address theabove challenge. Inspired by the idea of spatial data mining, theclassification method applies nuclear field to depicting the distributioninformation of pulse samples in feature space, and digs out thehidden cluster information by analyzing distribution characteristics.In addition, a membership-degree criterion to quantify the correlationamong all classes is established, which ensures classificationaccuracy of signal samples. Numerical experiments show that thepresented method can effectively prevent different working statesof multi-mode emitter from being classified as several emitters,and achieve higher classification accuracy.

Multi-mode process monitoring based on a novel weighted local standardization strategy and support vector data description

There are multiple operating modes in the real industrial process, and the collected data follow the complex multimodal distribution, so most traditional process monitoring methods are no longer applicable because their presumptions are that sampled-data should obey the single Gaussian distribution or non-Gaussian distribution. In order to solve these problems, a novel weighted local standardization(WLS) strategy is proposed to standardize the multimodal data, which can eliminate the multi-mode characteristics of the collected data, and normalize them into unimodal data distribution. After detailed analysis of the raised data preprocessing strategy, a new algorithm using WLS strategy with support vector data description(SVDD) is put forward to apply for multi-mode monitoring process. Unlike the strategy of building multiple local models, the developed method only contains a model without the prior knowledge of multi-mode process. To demonstrate the proposed method's validity, it is applied to a numerical example and a Tennessee Eastman(TE) process. Finally, the simulation results show that the WLS strategy is very effective to standardize multimodal data, and the WLS-SVDD monitoring method has great advantages over the traditional SVDD and PCA combined with a local standardization strategy(LNS-PCA) in multi-mode process monitoring.

Digital Communication Using Multi-mode Chaotic Lasers

The digital communication in a system of two multi-mode solid state chaotic lasers is investigated theoretically. If the usual method working well in a single-mode laser system is applied to a multi-mode laser system, the memory effect of the two nearest digits can cause high rate of mistakes when the digits are decoded through the subtraction of receiver output from the transmittal. By introducing the deviations of two nearest maximum and minimum fluctuationsof the signal to decode the digit, the message can be decoded correctly. Also, this communication method does not critically depend on the quality of the chaotic synchronization of the two multi-mode lasers.

Adaptive Learning-Based Delay-Sensitive and Secure Edge-End Collaboration for Multi-Mode Low-Carbon Power IoT

Multi-mode power internet of things(PIoT)combines various communication media to provide spatio-temporal coverage for low-carbon operation in smart park.Edge-end collaboration is feasible to achieve the full utilization of heterogeneous resources and anti-eavesdropping.However,edge-end collaboration-based multi-mode PIoT faces challenges of mutual contradiction in communication and security quality of service(QoS)guarantee,inadaptability of resource management,and multi-mode access conflict.We propose an Adaptive learning based delAysensitive and seCure Edge-End Collaboration algorithm(ACE_(2))to optimize multi-mode channel selection and split device power into artificial noise(AN)transmission and data transmission for secure data delivery.ACE_(2) can achieve multi-attribute QoS guarantee,adaptive resource management and security enhancement,and access conflict elimination with the combined power of deep actor-critic(DAC),“win or learn fast(WoLF)”mechanism,and edge-end collaboration.Simulations demonstrate its superior performance in queuing delay,energy consumption,secrecy capacity,and adaptability to differentiated low-carbon services.

Design of Multi-mode Mobile Terminal Chips

Based on the analysis of B3G evolution, the base-band processing chips for mobile terminals are introduced. Key technologies for multi-mode mobile terminal base-band chips are discussed. Terminal technologies are thought to be the key of B3G, and terminal base-band chips are regarded as the core of terminal technologies. Therefore, a unified wireless development platform is required for the R&D of multi-mode mobile terminal base-band processing chips.

三相PWM整流器离散空间矢量无模型预测电流控制策略

针对PWM整流器模型预测控制对系数参数准确性高度依赖的问题,提出一种基于离散空间矢量的无模型预测电流控制(MFPCC)策略。该策略通过矢量合成,在每个控制周期应用两个基本矢量,提高了预测电流的准确性;通过峰谷采样,分别测量并存储上一控制周期两个基本矢量作用下的电流梯度;并建立电流梯度方程,从而根据应用矢量的电流梯度进一步更新剩余6个未应用矢量的电流梯度,结合当前时刻的电流采样值,实现未来时刻的电流预测,得到下一时刻最优的虚拟矢量。该方法不依赖于任何系统参数,且消除了传统MFPCC策略中电流梯度更新停滞现象,降低了输出电流谐波。最后,通过实验和仿真验证了所提方法的有效性和优越性。

Hybrid input shaping control scheme for reducing vibration of robot based on multi-mode control

The classic multi-mode input shapers(MMISs)are valid to decrease multi-mode residual vibration of manipulators or robots simultaneously.But these input shapers cannot suppress more residual vibration with a quick response time when the frequency bandwidth of each mode vibration is very different.The methodologies and various types of multi-mode classic and hybrid input shaping control schemes with positive impulses were introduced in this paper.Six types of two-mode hybrid input shapers with positive impulses of a 3 degree of freedom robot were established.The ability and robustness of these two-mode hybrid input shapers to suppress residual vibration were analyzed by vibration response curve and sensitivity curve via numerical simulation.The response time of the zero vibration-zero vibration and derivative(ZV-ZVD)input shaper is the fastest,but the robustness is the least.The robustness of the zero vibration and derivative-extra insensitive(ZVD-EI)input shaper is the best,while the response time is the longest.According to the frequency bandwidth at each mode and required system response time,the most appropriate multi-mode hybrid input shaper(MMHIS)can be selected in order to improve response time as much as possible under the condition of suppressing more residual vibration.