Kernel Generalization of Multi-Rate Probabilistic Principal Component Analysis for Fault Detection in Nonlinear Process

In practical process industries,a variety of online and offline sensors and measuring instruments have been used for process control and monitoring purposes,which indicates that the measurements coming from different sources are collected at different sampling rates.To build a complete process monitoring strategy,all these multi-rate measurements should be considered for data-based modeling and monitoring.In this paper,a novel kernel multi-rate probabilistic principal component analysis(K-MPPCA)model is proposed to extract the nonlinear correlations among different sampling rates.In the proposed model,the model parameters are calibrated using the kernel trick and the expectation-maximum(EM)algorithm.Also,the corresponding fault detection methods based on the nonlinear features are developed.Finally,a simulated nonlinear case and an actual pre-decarburization unit in the ammonia synthesis process are tested to demonstrate the efficiency of the proposed method.

Performance Improvement of DCF Supporting Multi-Rate in IEEE 802.11b Wireless LAN

This paper proposes a new channel access algorithm based on channel occupancy time （COT） fairness to guarantee fairness and improve the aggregate throughput of 802.11b multi-rate WLANs. In the algorithm, the COT is used as fairness index to analyze the fairness of WLANs instead of the channel access probability （CAP） used in the distributed coordination function （DCF）. The standard COT is given by access point （AP） and broadcasted to all wireless stations. The AP and wireless stations in the WLAN can achieve COT-based fairness by adjusting their packet length, sending the multiple back-to-back packets at one time, or giving up an opportunity to access the channel. Analysis and simulations show that our algorithm can provide COT-fairness. Compared with the CAP-based algorithm, the proposed algorithm leads to improvements in aggregate throughput of IEEE 802. lib multi-rate WLANs.

Study of multi-rate multi-user detection based on supervision decision

Multi-user detection (MUD) based on multirate transmission in code division multiple access (CDMA) system is discussed. Under the requirement of signal interference ratio (SIR) detection at base station and framework with parallel interference cancellation, a supervision decision algorithm based on pre-decision of probabilistic data association (PDA) and hard decision is proposed. The detection performance is analyzed and simulation is implemented to show that the supervision decision algorithm improves the detection performance effectively.

A SINGLE PROCESSOR MULTI-RATE VOCODER

This paper presents the design of a full-duplex multi-rate vocoder which implements an LPC-10, CELPC and VSELPC algorithms in real time. A single commercially available digital signal processor IC, the TMS320C25, is used to perform the digital processing. The channel interfaces are configured with the design of ASIC, and including timing and control logic circuits.

Multi-rate tracking controller analysis and design for target tracking systems

As the sampling rates of the inner loop and the outer loop of the target tracking control system are different,a typical digital multi-rate control system was formed.If the traditional single-rate design method was applied,the low sampling rate loop will seriously impact the dynamical characteristic of the system.After analyzing and calculating the impact law of the low sampling rate loop to the bandwidth and the stability of the tracking system,a kind of multi-rate control system design method was introduced.Corresponding to the different sampling rates of the inner loop and the outer loop,the multi-rate control strategy was constituted by a high sampling rate sub-controller and a low sampling rate sub-controller.The two sub-controllers were designed separately and connected by means of the sampling rate converter.The low sampling rate controller determined the response rapidity of the system,while the high sampling rate controller applied additionally effective control outputs to the system during a sampling interval of the low sampling rate controller.With the introduced high and low sampling rates sub-controllers,the tracking control system can achieve the same performance as a single-rate controller with high sampling rate,yet it works under a much lower sampling rate.The simulation and experimental results show the effectiveness of the introduced multi-rate control design method.It reduces the settling time by 5 times and the over shoot by 4 times compared with the PID control.

Multi-rate sensor fusion-based adaptive discrete finite-time synergetic control for flexible-joint mechanical systems

This paper proposes an adaptive discrete finite-time synergetic control （ADFTSC） scheme based on a multi-rate sensor fusion estimator for flexible-joint mechanical systems in the presence of unmeasured states and dynamic uncertainties. Multi-rate sensors are employed to observe the system states which cannot be directly obtained by encoders due to the existence of joint flexibilities. By using an extended Kalman filter （EKF）, the finite-time synergetic controller is designed based on a sensor fusion estimator which estimates states and parameters of the mechanical system with multi-rate measurements. The proposed controller can guarantee the finite-time convergence of tracking errors by the theoretical derivation. Simulation and experimental studies are included to validate the effectiveness of the proposed approach.

A NOVEL CROSS-LAYER STRATEGY OF VIDEO TRANSMISSION TO SOLVE PERFORMANCE ANOMALY IN MULTI-RATE IEEE 802.11 NETWORKS

When wireless hosts use different rates to transmit data in IEEE 802.11 networks, it will take on the state of performance anomaly which will severely decrease the throughputs of all the higher rate hosts. Hence, it is bad for video service transmission. Considering that video is very sensitive to packet delivery delay but can tolerate some packet losses, we propose a novel cross-layer scheme which takes these two characteristics into consideration. Firstly, the maximum number of retransmissions for a video Medium Access Control (MAC) frame is computed in MAC layer according to video frame rate requirement of application layer and current access delay of MAC layer. Secondly, within the margin of the tolerant Packet Loss Rate (PLR) of application layer, several video MAC frames are allowed to drop so that we can adaptively select the transmission rate as high as possible for the rest of video MAC frames in terms of current channel quality and the maximum number of retransmissions. Experiment results show that the proposed method can reduce the delay and jitter of video service and improve the throughputs of fast hosts. Therefore, it increases the quality of reconstructed video to a certain extent and relieves the performance anomaly of network effectively.

BLIND DETECTION FOR MULTI-RATE DS-CDMA SYSTEM WITH ANTENNA ARRAY AT THE BASE STATION

In this paper, we propose the blind space-time high rate multi-user detector for synchronous uplink multi-rate Direct Sequence Code Division Multiple Access （DS-CDMA） systems with antenna array at the base station. By employing antenna array at the base stations, the spatial dimension is used efficiently to suppress co-channel interference and increase the capacity for multi-rate CDMA system. After low rate physical users in the system are modeled as corresponding high rate virtual users, we construct the space-time signature vectors of virtual users. And subspace projection algorithm is employed to estimate space-time signature vectors blindly. Then a soft-decision high rate lnultiuser detector is proposed based on the estimated signature vectors, which avoids estimating the ambiguous complex factors which are necessary in traditional blind detector. Numerical simulation results evaluate the performance in terms of Bit Error Rate （BER） for the proposed scheme. Simultaneously, it demonstrates that the system capability increases two times when using twoelement antenna array.

A NEW DESIGN METHOD OF CDMA SPREADING CODES BASED ON MULTI-RATE UNITARY FILTER BANK

It is well-known that the multi-valued CDMA spreading codes can be designed by means of a pair of mirror multi-rate filter banks based on some optimizing criterion. This paper indicates that there exists a theoretical bound in the performance of its circulating correlation property, which is given by an explicit expression. Based on this analysis, a criterion of maximizing entropy is proposed to design such codes. Computer simulation result suggests that the resulted codes outperform the conventional binary balanced Gold codes for an asynchronous CDMA system.

CHANNEL ESTIMATION OF MULTI-RATE DS-CDMA SIGNALS IN SLOW FADING MULTIPATH CHANNELS

In Direct-Sequence Code Division Multiple Access(DS-CDMA) mobile communi-cation systems, it is very important to obtain accurate estimation of the channel parameters,especially that of the propagation delay. But the near-far problem may make the estimationcomplicated and can degrade the estimation performance significantly. In this paper, an efficientMaximum Likelihood (ML) method is presented for channel parameter estimation of multi-rateDS-CDMA systems in slow fading multipath channels in a near-far scenario. The algorithmextended the ML approach to multi-rate DS-CDMA systems, and proposes decomposing a multi-dimensional optimization problem into a series of one-dimensional optimization and has improvedcomputational efficiency. Theoretical analysis and numerical examples show that the estimatorproposed is effective and near-far resistant.

On the Performance of Blind Chip Rate Estimation in Multi-Rate CDMA Transmissions Using Multi-Rate Sampling in Slow Flat Fading Channels

This paper considers blind chip rate estimation of DS-SS signals in multi-rate and multi-user DS-CDMA systems over channels having slow flat Rayleigh fading plus additive white Gaussian noise. Channel impulse response is estimated by a subspace method, and then the chip rate of each signal is estimated using zero crossing of estimated differential channel impulse response. For chip rate estimation of each user, an algorithm which uses weighted zero-crossing ratio is proposed. Maximum value of the weighted zero crossing ratio takes place in the Nyquist rate sampling frequency, which equals to the twice of the chip rate. Furthermore, bit time of each user is estimated using fluctuations of autocorrelation estimators. Since code length of each user can be obtained using bit time and chip time ratio. Fading channels reduce reliability factor of the proposed algo-rithm. To overcome this problem, a receiver with multiple antennas is proposed, and the reliability factor of the proposed algorithm is analyzed over both spatially correlated and independent fading channels.

Research of Multi-Rate LDPC Decoding in Optical Communication System

Low-density parity-check code (LDPC) not only has good performance approaching the Shannon limit, but also has low decoding complexity and flexible structure. It is a research hot-spot in the field of channel coding in recent years and has a wide range of application prospects in optical communication systems. In this paper, the decoding aspects and performance of LDPC codes are analyzed and compared according to the bit error rate (BER) of LDPC codes. The computer simulation was carried out under additive white Gaussian noise (AWGN) channel and binary phase shift keying (BPSK) modulation. Through theoretical analysis and simulation results, this paper explores the way of multi-rate LDPC decoding.

Recursive filtering of multi-rate cyber-physical systems with unknown inputs under adaptive event-triggered mechanisms

Cyber-physical systems(CPSs)take on the characteristics of both multiple rates of information collection and processing and the dependency on information exchanges.The purpose of this paper is to develop a joint recursive filtering scheme that estimates both unknown inputs and system states for multi-rate CPSs with unknown inputs.In cyberspace,the information transmission between the local joint filter and the sensors is governed by an adaptive event-triggered strategy.Furthermore,the desired parameters of joint filters are determined by a set of algebraic matrix equations in a recursive way,and a sufficient condition verifying the boundedness of filtering error covariance is found by resorting to some algebraic operation.A state fusion estimation scheme that uses local state estimation is proposed based on the covariance intersection(CI)based fusion conception.Lastly,an illustrative example demonstrates the effectiveness of the proposed adaptive event-triggered recursive filtering algorithm.

The study on the shrink-fit multi-ring flywheel with fall-off function

Structural integrity of the flywheel of reactor coolant pump is important for safe operation of a nuclear power plant. A shrink-fit multi-ring flywheel is designed with a fall-off function, i.e., it will separate from the shaft at a designed fall-off rotation speed, which is determined by the assembly process and the gravity. However, the two factors are ignored in the analytical method based on the Lame's equation. In this work, we conducted fall-off experiments to analyze the two factors and used the experimental data to verify the validity of the analytical method and the finite element method(FEM). The results show that FEM performs better than the analytical method in designing the falloff function of the flywheel, though FEM cannot successfully predict the strain variation with the rotational speed.

5-22 Design and Optimization of a Multi-re Time-of-flight Mass Analyzer for LPT

Multi-reflection time-of-flight mass spectrometer (MR-TOF-MS) is one of the new experimental devices developed in recent years. As the flight path extended several orders of magnitude as the analyzer is traversed many times by the ions, it allows achieving higher mass resolving power than the conventional time-of-flight mass spectrometry.

基于盲源分离的Multi-Rate DS/CDMA信号扩频序列盲估计

通过分析Multi-Rate DS/CDMA信号特性,建立的Multi-Rate DS/CDMA系统模型与线性混合的盲源分离模型一致,针对异、同步信号的不同特性,提出不同循环分段降维方法:对异步系统而言,采用2倍扩频周期为间隔对接收信号进行分割,利用Fast-ICA算法盲估计同一扩频周期用户的扩频序列,基于矢量2范数基础上估计各用户失步时间,并依此截取得到各用户的实际扩频序列,然后,循环至次大扩频周期进行盲估计,同时根据估计波形相似度归一化衡量函数消除最大周期分段序列,求解次大周期用户扩频序列,直至循环结束。对同步系统则以单倍最大扩频周期为间隔对接收信号进行分割,然后进行盲估计及降维处理。理论分析和仿真结果验证了本文方法的有效性。

CDMA系统多速率判决技术

在CDMA移动通信系统中,由于采用了可变速率声码嚣,所以在接收端需要用多速率判定算法来获取速率信息,从而正确地接收数据。本文介绍了多速率判定算法,分析了信道误码计数度量(SER)、山本度量YQM(Yamamoto Quality Metric)和CRC校验度量3种判定度量的产生原理和软件无线电实现方法,同时使用DSP+FPGA的结构对多速率判定进行了优化实现。

基于多采样率的频域倍频程研究

传统倍频程分析采用带通滤波器组算法实现,带通滤波器组算法仅能满足国家标准要求,并且用于分析分数阶倍频程时,滤波器组的数量及计算量成倍增长。提出了一种基于多采样率在频域分析倍频程及分数阶倍频程的算法。该算法首先对信号按通道重采样,并利用FFT转换到频域计算信号的倍频程及分数阶倍频程谱。仿真验证了算法的正确性,并与带通滤波器组算法做了比较。仿真及对比结果表明,相比于带通滤波器组算法,该算法能提供更好的谱分辨率,并且对于分数阶倍频程,该算法计算量明显少于滤波器组算法计算量。

Combinative Algorithms for the Multidisciplinary Collaborative Simulation of Complex Mechatronic Products Based on Major Step and Convergent Integration Step

Multidisciplinary collaborative simulation （MCS） is an important area of research in the domain of multidisciplinary design optimization （MDO）.Although previous research for MCS has to some extent addressed some issues like using of multiple tools,integration stability,control of step size,data synchronization,etc,further work is still necessary to study how to achieve improved precision.A theoretical model is formulated to describe and analyze the integration process of MCS.A basic algorithm with equal major steps is proposed based on the model,along with two methods of implementation for the model,namely the serial method and the parallel method.A further algorithm based on convergent integration step is proposed,which has a more flexible strategy for run-time integration.The influence of interpolation techniques on simulation performance is studied as well.Simulations of the performance of various algorithms with different interpolation techniques are performed for both a simple numerical example and a complex mechatronic product.The novel algorithm based on convergent integration step,when used with a high-order interpolation technique,has better performance in terms of precision and efficiency.The innovation of this paper is mainly on the validation of high precision of the proposed convergent integration step algorithm.

High throughput route selection in multi-rate wireless mesh networks

Most existing Ad-hoc routing protocols use the shortest path algorithm with a hop count metric to select paths. It is appropriate in single-rate wireless networks, but has a tendency to select paths containing long-distance links that have low data rates and reduced reliability in multi-rate networks. This article introduces a high throughput routing algorithm utilizing the multi-rate capability and some mesh characteristics in wireless fidelity （WiFi） mesh networks. It uses the medium access control （MAC） transmission time as the routing metric, which is estimated by the information passed up from the physical layer. When the proposed algorithm is adopted, the Ad-hoc on-demand distance vector （AODV） routing can be improved as high throughput AODV （HT-AODV）. Simulation results show that HT-AODV is capable of establishing a route that has high data-rate, short end-to-end delay and great network throughput.