Power-V诱导的钻柱黏滑振动特征分析

黏滑是石油钻井过程中影响钻井效率和井下钻柱安全的一种振动形式.垂直钻井系统Power-V在提供有效控斜力的同时,还会诱导钻柱黏滑振动.通过研究垂直钻井系统Power-V与井壁的接触作用及钻头与地层的相互作用模型,基于钻柱动力学有限元方法,深入分析Power-V的作用机理,研究其对扭转振动的影响,指出Power-V和井壁间的相互作用会导致钻柱与井壁的摩阻显著增加,进而引起摩阻扭矩的增大,诱导井下黏滑振动.实测振动数据证实,Power-V与井壁间的相互作用是引起钻柱黏滑振动的关键因素.这对于揭示黏滑振动的成因和更好地发挥Power-V的作用具有重要意义.

A Home Appliance Recognition System Using the Approach of Measuring Power Consumption and Power Factor on the Electrical Panel, Based on Energy Meter ICs

Currently a large effort is being done with the intention to educate people about how much energy each electrical appliance uses in their houses, since this knowledge is the fundamental basis of energy efficiency programs that can be managed by the household owners. This paper presents a simple yet functional non-intrusive method for electric power measurement that can be applied in energy efficiency programs, in order to provide a better knowledge of the energy consumption of the appliances in a home.

Power equipment vibration visualization using intelligent sensing method based on event-sensing principle

Vibration measurements can be used to evaluate the operation status of power equipment and are widely applied in equipment quality inspection and fault identification.Event-sensing technology can sense the change in surface light intensity caused by object vibration and provide a visual description of vibration behavior.Based on the analysis of the principle underlying the transformation of vibration behavior into event flow data by an event sensor,this paper proposes an algorithm to reconstruct event flow data into a relationship correlating vibration displacement and time to extract the amplitude-frequency characteristics of the vibration signal.A vibration measurement test platform is constructed,and feasibility and effectiveness tests are performed for the vibration motor and other power equipment.The results show that event-sensing technology can effectively perceive the surface vibration behavior of power and provide a wide dynamic range.Furthermore,the vibration measurement and visualization algorithm for power equipment constructed using this technology offers high measurement accuracy and efficiency.The results of this study provide a new noncontact and visual method for locating vibrations and performing amplitude-frequency analysis on power equipment.

Anomaly-Resistant Decentralized State Estimation Under Minimum Error Entropy With Fiducial Points for Wide-Area Power Systems

This paper investigates the anomaly-resistant decentralized state estimation(SE) problem for a class of wide-area power systems which are divided into several non-overlapping areas connected through transmission lines. Two classes of measurements(i.e., local measurements and edge measurements) are obtained, respectively, from the individual area and the transmission lines. A decentralized state estimator, whose performance is resistant against measurement with anomalies, is designed based on the minimum error entropy with fiducial points(MEEF) criterion. Specifically, 1) An augmented model, which incorporates the local prediction and local measurement, is developed by resorting to the unscented transformation approach and the statistical linearization approach;2) Using the augmented model, an MEEF-based cost function is designed that reflects the local prediction errors of the state and the measurement;and 3) The local estimate is first obtained by minimizing the MEEF-based cost function through a fixed-point iteration and then updated by using the edge measuring information. Finally, simulation experiments with three scenarios are carried out on the IEEE 14-bus system to illustrate the validity of the proposed anomaly-resistant decentralized SE scheme.

The Measuring System for Estimation of Power of Wind Flow Generated by Train Movement and Its Experimental Testing

The measuring system for estimation of power of wind flow generated by the train movement has been created. The advantages of the proposed system are the cheapness and simple design. With its simplicity of design and easy build-up of channels, designed measuring system can be used for a wide range of technical problems. This paper describes the design process, validation and conducting the first field test of this measuring system.

Development of a Module for Measuring Electrical Variables in Power Transformers Based in IoT,to Manage and Monitoring by Telemetry Mechanism

This work shows the development of a module that performs measurements of electrical variables in a low voltage power transformer.These variables are sent by means of the IEEE802.11 standard,connecting to a database stored in the cloud;associating with the meter IoT concepts,this to allow a client to perform an analysis,monitoring and management of their electrical network.For the construction of this module,non-invasive current sensors connected to a three-phase meter are used and a communication card is used that allows data to be extracted from the meter and sent to the cloud database.This module,to convert a conventional electrical power transformer into a smart electrical power transformer,making it a Smart Object and thus extract information from it telemetrically in real time.

Analysis on electric energy measuring method based on multi-resolution analysis

Along with the massive applications of the non-linear loads and the impact loads, many non-stationary stochastic signals such as harmonics, inter-harmonics, impulse signals and so on are introduced into the electric network, and these non-stationary stochastic signals have had effects on the accuracy of the measurement of electric energy. The traditional method like Fourier Analysis can be applied efficiently on the stationary stochastic signals, but it has little effect on non-stationary stochastic signals. In light of this, the form of the signals of the electric network in wavelet domain will be discussed in this paper. A measurement method of active power based on multi-resolution analysis in the stochastic process is presented. This method has a wider application scope compared with the traditional method Fourier analysis, and it is of good referential value and practical value in terms of raising the level of the existing electric energy measurement.

Power Pivot技术在工程建设信息化中的应用

为了工程项目和合同明细的管理,跟踪合同的执行情况,及时分析合同工期和费用的偏差,采用Power Pivot技术应用于工程建设信息化。通过建立数据表、关联关系,运用Power Pivot内置的度量值,分别建立查询相关度量值;最后通过Power Pivot内置的度量值,分别建立统计分析相关度量值。该方法实现了单人工程信息的合同管理,为工程建设信息化提供了可靠的技术支持。

Methods to Evaluate and Measure Power of Pneumatic System and Their Applications

Pneumatic system has been widely used throughout industry, and it consumes more than billions kW h of electricity one year all over the world. So as to improve the efficiency of pneumatic system, its power evaluation as well as measurement methods should be proposed, and their applicability should be validated. In this paper, firstly, power evaluation and measurement methods of pneumatic system were introduced for the first time. Secondly, based on the proposed methods, power distributions in pneumatic system was analyzed. Thirdly, through the analysis on pneumatic efficiencies of typical compressors and pneumatic components, the applicability of the proposed methods were validated. It can be concluded that, first of all, the proposed methods to evaluation and measurement the power of pneumatic system were efficient. Furthermore, the pneumatic power efficiencies of pneumatic system in the air production and cleaning procedure are respectively about 35%–75% and 85%–90%. Moreover, the pneumatic power efficiencies of pneumatic system in the transmission and consumption procedures are about 70%–85% and 10%–35%. And the total pneumatic power efficiency of pneumatic system is about 2%–20%, which varies largely with the system configuration. This paper provides a method to analyze and measure the power of pneumatic system, lay a foundation for the optimization and energy-saving design of pneumatic system.

Analysis and measurement of acoustic power in plastics ultrasonic welding process

A measuring principle for acoustic power in plastics ultrasonic welding process is introduced in this paper. Signal detection circuits of current, voltage, frequency, power for ultrasonic transducer of plastic ultrasonic welder are developed. A computer controlled measuring system is designed to sample the signals of welding process parameters. By using the designed system, the acoustic power curve during welding is calculated, saved, and displayed. And the relation between fusion state of plastics workpieces and input energy of joint is analyzed.

Calorimetric power measurements in the EAST ECRH system

In this paper, the measurement method of calorimetric power for an electron cyclotron resonance heating（ECRH） system for EAST is presented. This method requires measurements of the water flow through the cooling circuits and the input and output water temperatures in each cooling circuit. Usually, the inlet water temperature stability is controlled to obtain more accurate results.The influence of the inlet water temperature change on the measurement results is analyzed for the first time in this paper. Also, a novel temperature calibration method is proposed. This kind of calibration method is accurate and effective, and can be easily implemented.

Placido disk-based topography versus high-resolution rotating Scheimpflug camera for corneal power measurements in keratoconic and post-LASIK eyes：reliability and agreement

AIM：To compare the repeatability/reproducibility of measurement by high-resolution Placido disk-based topography with that of a high-resolution rotating Scheimpflug camera and assess the agreement between the two instruments in measuring corneal power in eyes with keratoconus and post-laser in situ keratomileusis（LASIK）. METHODS：One eye each of 36 keratoconic patients and 20 subjects who had undergone LASIK was included in this prospective observational study. Two independent examiners worked in a random order to take three measurements of each eye with both instruments. Four parameters were measured on the anterior cornea：steep keratometry（Ks）,flat keratometry（Kf）,mean keratometry（Km）,and astigmatism（Ks-Kf）. Intra-examiner repeatability and inter-examiner reproducibility were evaluated by calculating the within-subject standard deviation（Sw）the coefficient of repeatability（R）,the coefficient of variation（Co V）,and the intraclass correlation coefficient（ICC）. Agreement between instruments was tested with the BlandAltman method by calculating the 95% limits of agreement（95% Lo A）.RESULTS：In keratoconic eyes,the intra-examiner and inter-examiner ICC were 〉0.95. As compared with measurement by high-resolution Placido disk-based topography,the intra-examiner R of the high-resolution rotating Scheimpflug camera was lower for Kf（0.32 vs 0.88）,Ks（0.61 vs 0.88）,and Km（0.32 vs 0.84）but higher for Ks-Kf（0.70 vs 0.57）. Inter-examiner R values were lower for all parameters measured using the high-resolution rotating Scheimpflug camera. The 95% Lo A were-1.28 to ＋0.55 for Kf,-1.36 to ＋0.99 for Ks,-1.08 to ＋0.50 for Km,and-1.11 to ＋1.48 for Ks-Kf. In the post-LASIK eyes,the intra-examiner andinter-examiner ICC were 〉0.87 for all parameters. The intra-examiner and inter-examiner R were lower for all parameters measured using the high-resolution rotating Scheimpflug camera. The intra-examiner R was 0.17 vs 0.88 for Kf,0.21 vs 0.88 for Ks,0.17 vs 0.86 for Km,and 0.28 vs 0.33 for Ks-Kf. The inter-examiner R was 0.09 vs 0.64 for Kf,0.15 vs 0.56 for Ks,0.09 vs 0.59 for Km,and 0.18 vs 0.23 for Ks-Kf. The 95% Lo A were-0.54 to ＋0.58 for Kf,-0.51 to ＋0.53 for Ks and Km,and-0.28 to ＋0.27 for Ks-Kf. CONCLUSION：As compared with Placido disk-based topography,the high-resolution rotating Scheimpflug camera provides more repeatable and reproducible measurements of Ks,Kf and Ks in keratoconic and post-LASIK eyes. Agreement between instruments is fair in keratoconus and very good in post-LASIK eyes.

Power Aggregation Operators and Similarity Measures Based on Improved Intuitionistic Hesitant Fuzzy Sets and their Applications to Multiple Attribute Decision Making

Intuitionistic hesitant fuzzy set(IHFS)is amixture of two separated notions called intuitionistic fuzzy set(IFS)and hesitant fuzzy set(HFS),as an important technique to cope with uncertain and awkward information in realistic decision issues.IHFS contains the grades of truth and falsity in the formof the subset of the unit interval.The notion of IHFS was defined by many scholars with different conditions,which contain several weaknesses.Here,keeping in view the problems of already defined IHFSs,we will define IHFS in another way so that it becomes compatible with other existing notions.To examine the interrelationship between any numbers of IHFSs,we combined the notions of power averaging(PA)operators and power geometric(PG)operators with IHFSs to present the idea of intuitionistic hesitant fuzzy PA(IHFPA)operators,intuitionistic hesitant fuzzy PG(IHFPG)operators,intuitionistic hesitant fuzzy power weighted average(IHFPWA)operators,intuitionistic hesitant fuzzy power ordered weighted average(IHFPOWA)operators,intuitionistic hesitant fuzzy power ordered weighted geometric(IHFPOWG)operators,intuitionistic hesitant fuzzy power hybrid average(IHFPHA)operators,intuitionistic hesitant fuzzy power hybrid geometric(IHFPHG)operators and examined as well their fundamental properties.Some special cases of the explored work are also discovered.Additionally,the similarity measures based on IHFSs are presented and their advantages are discussed along examples.Furthermore,we initiated a new approach to multiple attribute decision making(MADM)problem applying suggested operators and a mathematical model is solved to develop an approach and to establish its common sense and adequacy.Advantages,comparative analysis,and graphical representation of the presented work are elaborated to show the reliability and effectiveness of the presented works.

The Wavefront Power Spectral Density Measurement of Aspheric Lens with Long Focal-Length Using a Computer-Generated Hologram

To ensure the performance of the optical system, the machining accuracy of lens with long focal lengths is required to ensure the image quality. A new method for lens transmission wavefront power spectral density (PSD) in mid-frequency domain measurement using binary phase computer-generated hologram (CGH) is presented. This technique is widely applicable and is particularly useful for measuring large-size lenses with long focal lengths. A comparison experiment of the CGH measurement with results from a Fizeau sphere interferometry method is carried out to verify the accuracy and convenience of the measurement. Furthermore, measurement uncertainty due to CGH fabrication process is analysed. Analysis of the CGH test showed the overall accuracy of less than 1 nm RMS for a sphere lens with over 30 m focal length and Φ410 mm clear aperture. CGH can provide reference spheres with high precision, in the meantime greatly shorten air space, thus reducing the effect of vibration and air turbulence, therefore is of great importance for lens transmission wavefront PSD measurement. The realization of high precision, high efficiency and nondestructive testing of long focal-lens wavefront PSD ensure the ultra-precision and certainty level of machining, hence improving the comprehensive performance of the optical system.

Temperature Effects on the Electrical Performance of Large Area Multicrystalline Silicon Solar Cells Using the Current Shunt Measuring Technique

The temperature effects on the electrical performance of a large area multicrystalline silicon solar cell with back-contact technology have been studied in a desert area under ambient conditions using the current shunt measuring technique. Therefore, most of the problems encountered with traditional measuring techniques are avoided. The temperature dependency of the current shunt from 5oC up to 50oC has been investigated. Its temperature coefficient proves to be negligible which means that the temperature dependency of the solar cell is completely independent of the current shunt. The solar module installed in a tilted position at the optimum angle of the location, has been tested in two different seasons (winter and summer). The obtained solar cell short circuit current, open circuit voltage and output power are correlated with the measured incident radiation in both seasons and all results are discussed.

Investigation on the multi-hole directional coupler for power measurement of the J-TEXT ECRH system

Power measurement is necessary for an electron cyclotron resonance heating(ECRH)system.The directional coupler method has been put forward to monitor high-power microwave from gyrotrons in real time.A multi-hole directional coupler has been designed and manufactured for the 105 GHz/500 kW ECRH system on the J-TEXT tokamak.During the design process,we established the relationships between hole parameters and coupling characteristics based on the multi-hole coupling method and small-hole coupling theory.High-power tests have been carried out.The results indicated the reasonability of the theoretical design and practicality of the fabricated directional coupler.Sources of test errors have been discussed in detail,and the influences of spurious modes on the directional couplers have been emphatically analyzed.

Instantaneous frequency measurement using two parallel I/Q modulators based on optical power monitoring

A scheme for instantaneous frequency measurement(IFM)using two parallel I/Q modulators based on optical power monitoring is proposed.The amplitude comparison function(ACF)can be constructed to establish the relationship between the frequency of radio frequency(RF)signal and the power ratio of two optical signals output by two I/Q modulators.The frequency of RF signal can be derived by measuring the optical power of the optical signals output by two I/Q modulators.The measurement range and measurement error can be adjusted by controlling the delay amount of the electrical delay line.The feasibility of the scheme is verified,and the corresponding measurement range and measurement error of the system under different delay amounts of the electrical delay line are given.Compared with previous IFM schemes,the structure of this scheme is simple.Polarization devices,a photodetector and an electrical power meter are not used,which reduces the impact of the environmental disturbance on the system and the cost of the system.In simulation,the measurement range can reach 0 GHz-24.5 GHz by adjusting the delay amount of the electrical delay lineτ=20 ps.The measurement error of the scheme is better at low frequency,and the measurement error of low frequency 0 GHz-9.6 GHz can reach-0.1 GHz to+0.05 GHz.

Experimental study of a technique for load measurement of powered supports

Despite the increasing popularity of mechanized coal mining, there are no convenient and accurate means available to measure the loads of powered supports. The measurement of such loads is important for monitoring mine pressure and ensuring production safety. The load-carrying features of a powered support were used to develop a method for load measurement using the mag-netoelastic principle. A cross bridge-type magnetoelastic stress sensor was designed for the support structures to measure the different parts of the supports. Tests on single-body hydraulic cylinders and simulated linkages showed that an approximately linear relationship between the values of the sensor output signal and the loads borne by the hydraulic cylinders or linkages. The results were used to analyze the load-carrying measurements of powered supports with the cross bridge-type magnetoelastic stress sensor.