Sol-gel technology was employed to synthesize nanosized precursors of La-Mg hydrogen storage alloy at different pH values (0.5, 1.5, 8.0 and 9.0) of reaction solution. The effect of pH value on microstructure of the n...Sol-gel technology was employed to synthesize nanosized precursors of La-Mg hydrogen storage alloy at different pH values (0.5, 1.5, 8.0 and 9.0) of reaction solution. The effect of pH value on microstructure of the nano precursors of La-Mg hydrogen storage alloy was studied by infrared radiation (IR), thermo-gravimetric and differential thermal analysis (TG/DTA), X-ray diffraction analyzer (XRD) and transmission electron microscopy (TEM). IR results indicate that the chelating agent, citric acid, is not fully ionized, and carboxyl groups are not entirely used to complex metal ions in acidic solutions. The efficiency of complexing metal ions is enhanced in basic solutions. TG/DTA results show that the combustion may take place with low rate of the flame propagation that causes the longer combustion time when pH<1.5. On the contrary, the dry gel synthesized in basic solution combusts at low ignition temperature and combustion reaction is violent; it is easy to form fine particles. XRD and TEM results reveal that the precursor powders are mainly two-phase mixture of La 2 O 3 and MgO. The morphology of the particles is almost flake with the size of ~30 nm when pH is 8.0.展开更多
Potential applications of Nano-scale science and technology are discussed in mineralogy, ore deposits, cosmochemistry and environmental sciences. Adsorption of nanometersized gold was experimentally studied on a varie...Potential applications of Nano-scale science and technology are discussed in mineralogy, ore deposits, cosmochemistry and environmental sciences. Adsorption of nanometersized gold was experimentally studied on a variety of minerals and rocks.展开更多
Nowadays, nano-technology is a promising option for scientists to enhance dental conditions and provide new techniques to offer a more reliable and comfortable therapeutic pickups. In this regard, there are different ...Nowadays, nano-technology is a promising option for scientists to enhance dental conditions and provide new techniques to offer a more reliable and comfortable therapeutic pickups. In this regard, there are different methods to manufacture novel nano-structured dental materials, and also modern drug delivery techniques. In this review article, all our efforts are based on the recently nano-dental approaches closely linked to treat or prevent some common dental diseases including tooth erosion, tooth sensitivity, periodontal disease, oral cancer, and so on. All the data and articles putted in this survey are gathered from Google Scholar, PubMed, and some dental databases.展开更多
At present, the most common micro/nano-scale fabri ca tion processes include the plane silicon process based on IC technology, stereo silicon process, LIGA, quasi-LIGA based on near ultra violet deep lithography, MEMS...At present, the most common micro/nano-scale fabri ca tion processes include the plane silicon process based on IC technology, stereo silicon process, LIGA, quasi-LIGA based on near ultra violet deep lithography, MEMS, energy beam etching and micro/nano-machining, etc. A common problem for t hese processes is the difficulty to fabricate arbitrary form for 3-dimensional micro/nano-parts, devices or mechanisms. To develop advanced MEMS manufacturin g technology, and to achieve fabrication of true 3-dimensional parts, devices or mechanisms, this paper proposes a nanofabrication technology for rapid proto typing of 3-dimensional parts, using plasma chemical vapor deposition (PCVD). This process can be describes as follows: A laser beam is produced by a low power, quasi molecule laser. It enters the vac uum chamber through a window, and is focused on with the substrate surface. A ga s in the chamber is ionized by the laser beam to produce PCVD on the substrate s urface, and forms a particle of the size of Ф100 nm (its thickness is about 100 nm). When the laser beam moves along X-axis, many particles form a line. Then the laser beam moves one step in Y-axis to form a new line. A plane is complete d by many lines. Then the substrate moves in Z-axis to form new plane. Eventu ally, many planes form a 3-dimensional component. Using available CAD/CAM softw are with this process, rapid prototyping of complex components can be achieved. A nanometer precision linear motor, such as that described in Chinese national p atent (patent No. ZL 98 2 16753.9), can be used to obtain the nanometer precisio n movements in the process. The process does not require mask, can be used for v arious rapid prototyping materials, to obtain high fabrication precision (its sc ale precision is 15 nm), and larger ratio of height to width of micro/nano-stru cture. It can find widespread applications in the fabrication of micro-mechani sm, trimming IC, and fabricating minilens, etc.展开更多
A novel suspension-floating-circulating fluidized combustion technology is proposed for burning coal slurry fuel in traditional circulating ftuidized bed boilers （CFBB）. This technology can solve some existing probl...A novel suspension-floating-circulating fluidized combustion technology is proposed for burning coal slurry fuel in traditional circulating ftuidized bed boilers （CFBB）. This technology can solve some existing problems in large- capacity CFBB burning coal slurry. The principles of the suspension-floating-circulating fluidized combustion technology were introduced in detail in this paper. A 130 t/h CFBB was retrofitted based on the technology, and the retrofitted system mainly includes a long-distance transport sub-system, a bed-material conveying sub-system with a wind-seal device invented by the authors, a superheater thermoregulation device using a novel temperature regulator, a return loop flu- idization facility, and a pneumatic ash conveying sub-system with sealed pump. The achieved performance of the retro- fitted CFBB shows that the thermal efficiency is 89.83 %, the combustion efficiency is 96.24 %, and the blending proportion of slurry is 94 %.展开更多
Capillary column preparation using perpentylated (2,3,6-tri-O-pentyl)-β-cyclodextrin asstationary phase by sol-gel technology with simplicity and rapidity is described. Multiplepreparation steps in conventional colum...Capillary column preparation using perpentylated (2,3,6-tri-O-pentyl)-β-cyclodextrin asstationary phase by sol-gel technology with simplicity and rapidity is described. Multiplepreparation steps in conventional column technology were avoided. The prepared columns exhibitsatisfactory chromatographic performances and pronounced selectivity for a wide range of testsolutes, and have been successfully used for the separation of nitrotoluene, dimethoxybenzene,alcohols, alkanes, dimethylphenol and cresol isomers.展开更多
Heptakis(2, 3, 6-tri-O-octyl)-β-cyclodextrin was coated onto the fused silica capillary by sol-gel technology. Column efficiency and column selectivity were studied. The results indicated that high ability of separat...Heptakis(2, 3, 6-tri-O-octyl)-β-cyclodextrin was coated onto the fused silica capillary by sol-gel technology. Column efficiency and column selectivity were studied. The results indicated that high ability of separation was acquired . Positional isomers of aromatic compounds were well separated.展开更多
Introduction and Invitation DICP Symposium is a special series of interna-tional conference named after the Dalian Instituteof Chemical Physics (DICP). The DICP Symposiumwas founded with the purpose to promote the int...Introduction and Invitation DICP Symposium is a special series of interna-tional conference named after the Dalian Instituteof Chemical Physics (DICP). The DICP Symposiumwas founded with the purpose to promote the interna-tional communication and collaboration between theDICP and the international scientific community, to展开更多
The purpose of this research is to implement an IT-based education program in order to promote cervical cancer screenings for women aged 20 - 29 years, as well as to examine the results of said program. This is a long...The purpose of this research is to implement an IT-based education program in order to promote cervical cancer screenings for women aged 20 - 29 years, as well as to examine the results of said program. This is a longitudinal/comparative study of two groups, one for which the program was implemented (the intervention group), and the other for which it was not (the control group). The program consisted of attending a health lecture and encouragement to be screened one month, six months, and one year later sent through IT-based methods. The target was unmarried women aged 20 - 29 who had neither previously given birth nor had been screened for cervical cancer in a period one year prior. They were divided into two groups, the intervention group (n = 142) and control group (n = 145). The effectiveness of the program was assessed via an initial survey and further surveys six months and one year later. Results were based on the Japanese version of the Health Belief Model Scale for Cervical Cancer and the Pap Smear Test (HBMSCCPST), knowledge scores in the categories of Healthy Lifestyles, Cervical Cancer, Cervical Cancer Screening, and screening behavior. A two-way ANOVA of the HBMSCCPST subscales and knowledge scores in the initial, six-month, and one-year surveys was performed, showing interaction in Cervical Cancer (p = 0.00). Main effects were observed in Cervical Cancer Screening (p = 0.00) and Healthy Lifestyles (p = 0.00). Regarding the amount of change from the initial survey, knowledge scores in the Cervical Cancer (p = 0.027) and Cervical Cancer Screening (p = 0.016) categories were significantly higher in the intervention group than in the control group. There was no significant difference in cervical cancer screening rates (p = 0.26) between the two groups. However, a small-degree effect size was observed for Benefits, Seriousness, and Susceptibility subscales in both examinees and non-examinees. Although the educational program of this study was effective in improving the knowledge of women in their twenties, there was little improvement in HBMSCCPST and it did not lead to the promotion of cervical cancer screening. In order to raise interest in cervical cancer screening, it is necessary to consider useful content to guide women to consult with healthcare professionals, a long-term population approach, and organizational structure of consultation.展开更多
3 - dimensional body measurement technology, the basis of developing high technology in industry, accelerates digital development of aplparel industry. This paper briefly introduces the history of 3 - dimensional body...3 - dimensional body measurement technology, the basis of developing high technology in industry, accelerates digital development of aplparel industry. This paper briefly introduces the history of 3 - dimensional body measurement technology, and recounts the principle and primary structure of some types of 3 - dimensional automatic body measurement system. With this understanding, it discusses prospect of 3- dimensional CAD and virtual technology used in apparel industry.展开更多
This study was conducted to investigate the in-vitro production technology of embryos from young Dorper sheep, so as to provide technical support for the utilization of ovarian follicles in young Dorper sheep. Tests w...This study was conducted to investigate the in-vitro production technology of embryos from young Dorper sheep, so as to provide technical support for the utilization of ovarian follicles in young Dorper sheep. Tests were conducted from the induction of Dorper sheep of 4 to 8 weeks old using follicle stimulating hormone(FSH) and pregnant horse serum(PMSG), collection of oocytes, in-vitro oocyte maturation-fertilization-zygote cultivation and 2-4-cell-stage fertilized ovum transfer. The results showed that 585 oocytes were collected from eight Dorper sheep at the age of 4 and 8 weeks, with an average of 73.13 oocytes/sheep. 346 of the 2-4-cell-stage fertilized eggs were obtained, whose cleavage rate was 59.15%. 77 in-vitro fertilized eggs at 2-4-cell stage were transplanted into 17 recipient sheep, seven of which were pregnant and gave birth to 13 "test-tube sheep" with a conception rate of 41.18%. It is indicated that the hormone induction technique, in-vitro oocyte maturation-fertilization-zygote cultivation technique and 2-4-cell-stage fertilized ovum transfer technique used in this study can serve as effective techniques for the in-vitro production of embryos from Dorper sheep of 4-8 weeks old.展开更多
Nowadays Quantum Cellular Automata (QCA) as the leading technology in design of microelectronic systems has been raised. With respect to high velocity and density in low power and also simple concepts, this technology...Nowadays Quantum Cellular Automata (QCA) as the leading technology in design of microelectronic systems has been raised. With respect to high velocity and density in low power and also simple concepts, this technology is a viable alternative to CMOS technology. In collector design, the primary component of each processor is very important. Due to the small elements in this technology, failure rate in manufacturing process technology is very high. In the other hand, the simulation shows that the intersection point of two wires is one of the critical points in QCA circuits. This means that defects in the manufacturing process around these points can cause malfunction in the circuit performance. In this paper, a collector in cross sections of wire in his new method used higher reliability against defects during manufacturing has been developed. QCA Designer software is used to simulate the case study system.展开更多
基金supported by the Open Foundation of Key Laboratory of the Ministry of Educationof Nonferrous Metal Alloys and Processes(No.EKL09002)The Ph.D.Fund Project of Lanzhou University of Science and Technology(No.BS01200904)
文摘Sol-gel technology was employed to synthesize nanosized precursors of La-Mg hydrogen storage alloy at different pH values (0.5, 1.5, 8.0 and 9.0) of reaction solution. The effect of pH value on microstructure of the nano precursors of La-Mg hydrogen storage alloy was studied by infrared radiation (IR), thermo-gravimetric and differential thermal analysis (TG/DTA), X-ray diffraction analyzer (XRD) and transmission electron microscopy (TEM). IR results indicate that the chelating agent, citric acid, is not fully ionized, and carboxyl groups are not entirely used to complex metal ions in acidic solutions. The efficiency of complexing metal ions is enhanced in basic solutions. TG/DTA results show that the combustion may take place with low rate of the flame propagation that causes the longer combustion time when pH<1.5. On the contrary, the dry gel synthesized in basic solution combusts at low ignition temperature and combustion reaction is violent; it is easy to form fine particles. XRD and TEM results reveal that the precursor powders are mainly two-phase mixture of La 2 O 3 and MgO. The morphology of the particles is almost flake with the size of ~30 nm when pH is 8.0.
文摘Potential applications of Nano-scale science and technology are discussed in mineralogy, ore deposits, cosmochemistry and environmental sciences. Adsorption of nanometersized gold was experimentally studied on a variety of minerals and rocks.
文摘Nowadays, nano-technology is a promising option for scientists to enhance dental conditions and provide new techniques to offer a more reliable and comfortable therapeutic pickups. In this regard, there are different methods to manufacture novel nano-structured dental materials, and also modern drug delivery techniques. In this review article, all our efforts are based on the recently nano-dental approaches closely linked to treat or prevent some common dental diseases including tooth erosion, tooth sensitivity, periodontal disease, oral cancer, and so on. All the data and articles putted in this survey are gathered from Google Scholar, PubMed, and some dental databases.
文摘At present, the most common micro/nano-scale fabri ca tion processes include the plane silicon process based on IC technology, stereo silicon process, LIGA, quasi-LIGA based on near ultra violet deep lithography, MEMS, energy beam etching and micro/nano-machining, etc. A common problem for t hese processes is the difficulty to fabricate arbitrary form for 3-dimensional micro/nano-parts, devices or mechanisms. To develop advanced MEMS manufacturin g technology, and to achieve fabrication of true 3-dimensional parts, devices or mechanisms, this paper proposes a nanofabrication technology for rapid proto typing of 3-dimensional parts, using plasma chemical vapor deposition (PCVD). This process can be describes as follows: A laser beam is produced by a low power, quasi molecule laser. It enters the vac uum chamber through a window, and is focused on with the substrate surface. A ga s in the chamber is ionized by the laser beam to produce PCVD on the substrate s urface, and forms a particle of the size of Ф100 nm (its thickness is about 100 nm). When the laser beam moves along X-axis, many particles form a line. Then the laser beam moves one step in Y-axis to form a new line. A plane is complete d by many lines. Then the substrate moves in Z-axis to form new plane. Eventu ally, many planes form a 3-dimensional component. Using available CAD/CAM softw are with this process, rapid prototyping of complex components can be achieved. A nanometer precision linear motor, such as that described in Chinese national p atent (patent No. ZL 98 2 16753.9), can be used to obtain the nanometer precisio n movements in the process. The process does not require mask, can be used for v arious rapid prototyping materials, to obtain high fabrication precision (its sc ale precision is 15 nm), and larger ratio of height to width of micro/nano-stru cture. It can find widespread applications in the fabrication of micro-mechani sm, trimming IC, and fabricating minilens, etc.
文摘A novel suspension-floating-circulating fluidized combustion technology is proposed for burning coal slurry fuel in traditional circulating ftuidized bed boilers （CFBB）. This technology can solve some existing problems in large- capacity CFBB burning coal slurry. The principles of the suspension-floating-circulating fluidized combustion technology were introduced in detail in this paper. A 130 t/h CFBB was retrofitted based on the technology, and the retrofitted system mainly includes a long-distance transport sub-system, a bed-material conveying sub-system with a wind-seal device invented by the authors, a superheater thermoregulation device using a novel temperature regulator, a return loop flu- idization facility, and a pneumatic ash conveying sub-system with sealed pump. The achieved performance of the retro- fitted CFBB shows that the thermal efficiency is 89.83 %, the combustion efficiency is 96.24 %, and the blending proportion of slurry is 94 %.
文摘Capillary column preparation using perpentylated (2,3,6-tri-O-pentyl)-β-cyclodextrin asstationary phase by sol-gel technology with simplicity and rapidity is described. Multiplepreparation steps in conventional column technology were avoided. The prepared columns exhibitsatisfactory chromatographic performances and pronounced selectivity for a wide range of testsolutes, and have been successfully used for the separation of nitrotoluene, dimethoxybenzene,alcohols, alkanes, dimethylphenol and cresol isomers.
文摘Heptakis(2, 3, 6-tri-O-octyl)-β-cyclodextrin was coated onto the fused silica capillary by sol-gel technology. Column efficiency and column selectivity were studied. The results indicated that high ability of separation was acquired . Positional isomers of aromatic compounds were well separated.
文摘Introduction and Invitation DICP Symposium is a special series of interna-tional conference named after the Dalian Instituteof Chemical Physics (DICP). The DICP Symposiumwas founded with the purpose to promote the interna-tional communication and collaboration between theDICP and the international scientific community, to
文摘The purpose of this research is to implement an IT-based education program in order to promote cervical cancer screenings for women aged 20 - 29 years, as well as to examine the results of said program. This is a longitudinal/comparative study of two groups, one for which the program was implemented (the intervention group), and the other for which it was not (the control group). The program consisted of attending a health lecture and encouragement to be screened one month, six months, and one year later sent through IT-based methods. The target was unmarried women aged 20 - 29 who had neither previously given birth nor had been screened for cervical cancer in a period one year prior. They were divided into two groups, the intervention group (n = 142) and control group (n = 145). The effectiveness of the program was assessed via an initial survey and further surveys six months and one year later. Results were based on the Japanese version of the Health Belief Model Scale for Cervical Cancer and the Pap Smear Test (HBMSCCPST), knowledge scores in the categories of Healthy Lifestyles, Cervical Cancer, Cervical Cancer Screening, and screening behavior. A two-way ANOVA of the HBMSCCPST subscales and knowledge scores in the initial, six-month, and one-year surveys was performed, showing interaction in Cervical Cancer (p = 0.00). Main effects were observed in Cervical Cancer Screening (p = 0.00) and Healthy Lifestyles (p = 0.00). Regarding the amount of change from the initial survey, knowledge scores in the Cervical Cancer (p = 0.027) and Cervical Cancer Screening (p = 0.016) categories were significantly higher in the intervention group than in the control group. There was no significant difference in cervical cancer screening rates (p = 0.26) between the two groups. However, a small-degree effect size was observed for Benefits, Seriousness, and Susceptibility subscales in both examinees and non-examinees. Although the educational program of this study was effective in improving the knowledge of women in their twenties, there was little improvement in HBMSCCPST and it did not lead to the promotion of cervical cancer screening. In order to raise interest in cervical cancer screening, it is necessary to consider useful content to guide women to consult with healthcare professionals, a long-term population approach, and organizational structure of consultation.
基金item of significant subject construction in Shanghai
文摘3 - dimensional body measurement technology, the basis of developing high technology in industry, accelerates digital development of aplparel industry. This paper briefly introduces the history of 3 - dimensional body measurement technology, and recounts the principle and primary structure of some types of 3 - dimensional automatic body measurement system. With this understanding, it discusses prospect of 3- dimensional CAD and virtual technology used in apparel industry.
基金Supported by Earmarked Fund for Construction of National Wool Sheep Industry Technology Research System(CARS-39-24)Program for Science and Technology Development of Shanxi Province(20120311024-1)+1 种基金Fund for Science and Technology Innovation Team in Shanxi Province(201705D131028-20)Shanxi Agricultural Industry Development Technology Leading Fund(2017CYYL-08)
文摘This study was conducted to investigate the in-vitro production technology of embryos from young Dorper sheep, so as to provide technical support for the utilization of ovarian follicles in young Dorper sheep. Tests were conducted from the induction of Dorper sheep of 4 to 8 weeks old using follicle stimulating hormone(FSH) and pregnant horse serum(PMSG), collection of oocytes, in-vitro oocyte maturation-fertilization-zygote cultivation and 2-4-cell-stage fertilized ovum transfer. The results showed that 585 oocytes were collected from eight Dorper sheep at the age of 4 and 8 weeks, with an average of 73.13 oocytes/sheep. 346 of the 2-4-cell-stage fertilized eggs were obtained, whose cleavage rate was 59.15%. 77 in-vitro fertilized eggs at 2-4-cell stage were transplanted into 17 recipient sheep, seven of which were pregnant and gave birth to 13 "test-tube sheep" with a conception rate of 41.18%. It is indicated that the hormone induction technique, in-vitro oocyte maturation-fertilization-zygote cultivation technique and 2-4-cell-stage fertilized ovum transfer technique used in this study can serve as effective techniques for the in-vitro production of embryos from Dorper sheep of 4-8 weeks old.
文摘Nowadays Quantum Cellular Automata (QCA) as the leading technology in design of microelectronic systems has been raised. With respect to high velocity and density in low power and also simple concepts, this technology is a viable alternative to CMOS technology. In collector design, the primary component of each processor is very important. Due to the small elements in this technology, failure rate in manufacturing process technology is very high. In the other hand, the simulation shows that the intersection point of two wires is one of the critical points in QCA circuits. This means that defects in the manufacturing process around these points can cause malfunction in the circuit performance. In this paper, a collector in cross sections of wire in his new method used higher reliability against defects during manufacturing has been developed. QCA Designer software is used to simulate the case study system.
