Study on Acoustic Emission Characteristics of Deformation Damage Process of Zirconia Ceramics

Zirconia ceramics have become increasingly widely used in recent years and are favored by relevant enterprises. From the traditional dental field to aerospace, parts manufacturing has been used, but there is limited research on the deformation and damage process of zirconia ceramics. This article analyzes the acoustic emission characteristics of each stage of ceramic damage from the perspective of acoustic emission, and explores its deformation process characteristics from multiple perspectives such as time domain, frequency, and EWT modal analysis. It is concluded that zirconia ceramics exhibit higher brittleness and acoustic emission strength than alumina ceramics, and when approaching the fracture, it tends to generate lower frequency acoustic emission signals.

Osteoblast Behavior on Hierarchical Micro-/Nano-Structured Titanium Surface

In the present work, osteoblast behavior on a hierarchical micro-/nano-structured titanium surface was investigated. A hi- erarchical hybrid micro-/nano-structured titanium surface topography was produced via Electrolytic Etching （EE）. MG-63 cells were cultured on disks for 2 h to 7 days. The osteoblast response to the hierarchical hybrid micro-/nano-structured titanium surface was evaluated through the osteoblast cell morphology, attachment and proliferation. For comparison, MG-63 cells were also cultured on Sandblasted and Acid-etched （SEA） as well as Machined （M） surfaces respectively. The results show signifi- cant differences in the adhesion rates and proliferation levels of MG-63 cells on EE, SLA, and M surfaces. Both adhesion rate and proliferation level on EE surface are higher than those on SLA and M surfaces. Therefore, we may expect that, comparing with SLA and M surfaces, bone growth on EE surface could be accelerated and bone formation could be promoted at an early stage, which could be applied in the clinical practices for immediate and early-stage loadings.

Preparation and Characterization of Nano-Structured SiO_(2) Thin Films on Carbon Steel

Nano-structured SiO2 thin films were prepared on the surface of carbon steel for the first time by LPD. The compositions of the films were analyzed by XPS, and the surface morphology of the thin films were observed by AFM. The thin films were constituted by compact particles of SiO2, and there was no Fe in the films. In the process of film forming, the SiO2 colloid particles were deposited or absorbed directly onto the surface of carbon steel substrates that were activated by acid solution containing inhibitor, and corrosion of the substrates was avoided. The nano-structured SiO2 thin films that were prepared had excellent protective efficiency to the carbon steel.

Electron emission degradation of nano-structured sp^2-bonded amorphous carbon films

The initial field electron emission degradation behaviour of original nano-structured sp^2-bonded amorphous carbon films has been observed, which can be attributed to the increase of the work function of the film in the field emission process analysed using a Fowler-Nordheim plot. The possible reason for the change of work function is suggested to be the desorption of hydrogen from the original hydrogen termination film surface due to field emission current-induced local heating. For the explanation of the emission degradation behaviour of the nano-structured sp2-bonded amorphous carbon film, a cluster model with a series of graphite （0001） basal surfaces has been presented, and the theoretical calculations have been performed to investigate work functions of graphite （0001） surfaces with different hydrogen atom and ion chemisorption sites by using first principles method based on density functional theory-local density approximation.

Preparation of nano-structured Ag solid materials and application to surface-enhanced Raman scattering

Silver nano-particles with average diameter of about 60 nm were compacted in a high-strength mold under different pressures at 523 K to produce nano-structured Ag solid materials. The structure and characteristic of the nano-structured Ag solid materials (NSS-Ag) were studied using X-ray diffraction (XRD), scanning electron microscope (SEM) and Raman spectrometer. The NSS-Ag could be used as highly efficient surface-enhanced Raman scattering (SERS) active substrates. The common probe molecules Rhodamine 6G (R6G, 1×10-10 mol/L) were used to test the SERS activity on these substrates at very low concentrations. It is found that the SERS enhancement ability is dependent on the density of NSS-Ag. When the relative density of NSS-Ag is 83.87%, the materials reveal great SERS signal.

Cobalt supported on CNTs-covered γ-and nano-structured alumina catalysts utilized for wax selective Fischer-Tropsch synthesis

Cobalt supported on carbon nanotubes （CNTs）-covered alumina has been recently developed and successfully utilized as a catalyst in Fischer-Tropsch synthesis （FTS）. Problems associated with shaping of Co/CNTs into extrudates or pellets as well as catalyst attrition rendered these materials unfavorable for industrial applications. In this investigation regular γ- and nano-structured （N-S） alumina as well as CNTs-covered regular γ- and N-S-alumina supports were impregnated by cobalt nitrate solution to make new cobalt-based catalysts which were also promoted by Ru. The catalysts were characterized and tested in a micro reactor to evaluate their applicability in FTS. γ-Al2O3 was prepared by calcination of bohemite and N-S-Al2O3 was prepared by sol-gel method using aluminum chloride as starting material. Catalyst evaluations indicated that N-S-Al2O3 was superior to regular γ-Al2O3 and that CNTs-covered alumina supports were favored over non-covered ones in terms of activity and heavy hydrocarbon selectivity. These were justified by porosimetric characteristics of the catalysts and existence of CNTs points of view. CNTs-covered catalysts also showed higher wax selectivity and better resistance to deactivation. Furthermore, TPR analysis indicated that the cobalt aluminate phase, which is responsible for the permanent deactivation of alumina supported Co-based catalysts, did not form on alumina supported Co-based catalysts covered with CNTs due to weaker interactions between cobalt and alumina.

Deposition mechanism of nano-structured single-layered C_(36) film on a diamond (100) crystal plane

The Brenner-LJ potential is adopted to describe the interaction between C36 clusters and diamond surface, and the deposition mechanism of multi-C36 clusters on the diamond surface is also studied by using the method of molecular dynamics simulation. The simulation results show that the competition effects of two interactions, i.e. the interaction between cluster and cluster and the interaction between cluster and crystal plane, are studied, and then the influence of these competition effects on C36 cluster deposition is analysed. The finding is that when an incident energy is appropriately chosen, C36 clusters can be chemically adsorbed and deposited steadily on the diamond surface in the form of single-layer, and in the deposition process the multi-C36 clusters present a phenomenon of energy transmission. The experimental result shows that at a temperature of 300K, in order to deposit C36 clusters into a steady nanostructured single-layered film, the optimal incident energy is between 10 and 18 eV, if the incident energy is larger than 18 eV, the C36 clusters will be deposited into an island nano-structured film.

A Comparative Study on the Milling Speed for the Synthesis of Nano-Structured Al 6063 Alloy Powder by Mechanical Alloying

The present article reports on characterization studies performed on amorphized nanostructured Al 6063 alloy powder synthesized by mechanical alloying (MA). The as-milled powder was characterized by X-ray diffraction (XRD) for investigating the development of crystallite nature and determining the different phases of the materials present, scanning electron microscope (SEM) was used for in depth morphological study and High Resolution-transmission electron microscope (HR-TEM) was employed to ensure the development of a nano-structured nature of the Al 6063 matrix. In the present work alloyed powder was milled for 20 h and 40 h at 300 rpm;and 20 h at 700 rpm in a hardened stainless steel medium. Using Williamson-Hall equation;crystallite size, lattice strain and lattice parameter of Al 6063 nanostructure alloy powder was estimated with broadening of XRD peaks. XRD results showed that the crystallite size of Al 6063 alloy powder reached 32 and 53 nm after 20 h at 700 rpm and 40 h at 300 rpm respectively.

Enhancing Mechanical Stability of Nano-Structured Anti-Reflection Coatings

Periodic Nanostructured anti-reflection coatings (NALs) are a promising option for enhancing transmission of coherent light without inducing scattering. We’ve found that reducing the height of NALs below a critical value to enhance mechanical stability can highly reduce the transmission efficiency. Here, using Rigorous Couples Wave Analysis (RCWA), we find the minimum height for over 99% transmission and effect of height on transmission bandwidth. Then, during a one-step plasma etching, two samples with different heights have been generated and their efficiency is evaluated using RCWA.

The 18.3% Silicon Solar Cells with Nano-Structured Surface and Rear Emitter

A nano-structured surface is formed on the pyramid structure of n-type silicon solar cells by size-controlled silver nano-particle assisted etching. Such a nano-structure creates a front average weighted reflectance of less than 2.5% in the 300-1200nm range due to the broadband reflection suppression. The sodium hydroxide is used to obtain the low-area surface by post-etching the nano-structure, thus the severe carrier recombination associated with the nano-structured surface could be reduced. After emitter forming, screen printing and firing by means of the industrial fabrication protocol, an 18.3%-efficient nano-structured silicon solar cell with rear emitter is fabricated. The process of fabricating the solar cells matches well with industrial manufacture and shows promising prospects.

Comparative Assessment on Machinability of Nano-Structured Bainitic Steel and Titanium64

Titanium64 has characteristics well sought after for applications in demanding environments. In general, due to titanium64’s high performance, it is a material which requires careful and well considered machining approaches in order to optimize the process. Nano-structured bainitic steel whilst having different application bases does none the less have similar machining and machinability short comes as that of titanium64. These similar characteristics have been compared and contrasted in this research study using parameters including cutting force, surface texture and metallography. The results tend to indicate that titanium64 has a poorer machinability characteristics compared to nano-structured bainitic steel. However, in terms of achieving greater surface texture characteristics, the nano-structured bainitic steel exhibited an enhanced capacity.

Research on the field emission mechanism of nano-structured carbon film

The field emission （FE） characteristics of nano-structured carbon films （NSCFs） are investigated. The saturation behaviour of the field emission current density found at high electric field E cannot be reasonably explained by the traditional Fowler-Nordheim （F-N） theory. A three-region E model and the curve-fitting method are utilized for discussing the FE characteristics of NSCFs. In the low, high, and middle E regions, the FE mechanism is reasonably explained by a modified F-N model, a corrected space-charge-limited-current （SCLC） model and the joint model of F N and SCLC mechanism, respectively. Moreover, the measured FE data accord well with the results from our corrected theoretical model.

Nacre-inspired Zirconia/Carbon Nanocomposites with High Strength and Toughness

Inspired by structures of natural shells,zirconia-carbon nanocomposites were obtained by using natural chitin from shrimp shells as templates via the sol-gel route in this study.Chitin was dispersed in the water and chelated with the zirconia precursors by amidogen.After a heat treatment for carbonization,nacre-like structures of carbon-zirconia nanocomposites were successfully synthesized.Due to the toughening mechanism of tetragonal zirconia,the mechanical properties of carbon-zirconia composites are further improved.The as-received zirconia/carbon nanocomposite with best mechanical property has a hardness of 5.88GPa and an elastic modulus of 80.6 GPa,which is even stronger than natural shells.This work might facilitate a versatile platform for developing green nanocomposites with reasonably good mechanical properties.

Replacement of Unesthetic Posterior Metal Crowns with Monolithic Zirconia Crowns: A Case Report

Advances in metal-free materials and the popularization of Computer-Aided Design and Manufacturing (CAD/CAM) have led to the wide clinical use of all-ceramic crowns for esthetic restorations. A 72-year-old woman presented to our hospital with unesthetic restorations on the right upper and lower posterior teeth. Intraoral examination revealed poorly fitting metal crown margins. Defective prostheses were removed, and provisional restorations were provided to stabilize the mandibular position. Optical impressions and the maxillomandibular relationship were recorded using an intraoral scanner, and monolithic zirconia crowns were fabricated using CAD/CAM technology for complete veneer crown restorative treatment. Occlusal examination revealed an improvement in occlusal force distribution at initial examination (right side: 33.5%, left side: 66.5%) after placement of the zirconia crowns (right side: 54.9%, left side: 45.1%). Occlusal force and occlusal force distribution area also showed an increasing trend. The Oral Health Impact Profile short form (OHIP-14) score decreased from 7 points at initial examination to 0 points after prosthodontic treatment. Appropriate diagnosis and treatment planning contributed to the increased occlusal force and balanced occlusal force distribution. Therefore, the present case indicates the potential of monolithic zirconia crowns to achieve both esthetic and stable functional outcomes.

Machine learning potential for Ab Initio phase transitions of zirconia

Zirconia has been extensively used in aerospace,military,biomedical and industrial fields due to its unusual combination of high mechanical,electrical and thermal properties.However,the fundamental and critical phase transition process of zirconia has not been well studied because of its difficult first-order phase transition with formidable energy barrier.Here,we generated a machine learning interatomic potential with ab initio accuracy to discover the mechanism behind all kinds of phase transition of zirconia at ambient pressure.The machine learning potential precisely characterized atomic interactions among all zirconia allotropes and liquid zirconia in a wide temperature range.We realized the challenging reversible first-order monoclinic-tetragonal and cubicliquid phase transition processes with enhanced sampling techniques.From the thermodynamic information,we gave a better understanding of the thermal hysteresis phenomenon in martensitic monoclinic-tetragonal transition.The phase diagram of zirconia from our machine learning potential based molecular dynamics simulations corresponded well with experimental results.

Preparation of nano-structured pure rare-earth bulks by combining inert-gas condensation with SPS

A number of techniques have been developed to synthesize nanocrystalline bulk materials,including inert-gas condensation and consolidation,electrodeposition,severe plastic deformation,crystallization of amorphous solid,surface mechanical attrition,and powder metallurgy.However,it is hard to produce the bulk with controllable nanostructures,especially with the grain sizes controllable in a wide range below 100 nm.In the conventional powder metallurgy,due to the fact that rapid coarsening of the particles ...

Effect of Zirconia Corundum Addition on Properties of Chrome Corundum Castables

In order to investigate the effect of zirconia corundum on the preparation of chrome corundum castables,samples were prepared using tabular corundum,white fused corundum,active alumina micropowder,chromium oxide micropowder and fused ziconia corundum particles as the main raw materials,and pure calcium aluminate cement as the binder.The effects of the fused zirconia corundum particles addition(1-0.5 mm,0,4.5%,9%,and 18%,by mass)on the linear change rate,the apparent porosity,the cold modulus of rupture,and the thermal shock resistance of chrome corundum castables were studied,and the microstructure of the samples was analyzed.The results show that:(1)with the zirconia corundum addition increasing,the permanent linear change on heating of the samples gradually increases,the apparent porosity gradually increases,the cold modulus of rupture gradually decreases,and the thermal shock resistance gradually increases;(2)according to SEM,it can be found that the phase transformation of ZrO2 after heat treatment leads to a large number of microcracks in the material.On one hand,the cold modulus of rupture of the material is reduced;on the other hand,the thermal shock resistance of the material is improved.

Preparation and Mechanical Properties of Zirconia Ceramics Doped with Different Y_(2)O_(3)Contents

The sintering behavior and mechanical properties of zirconia doped with 2.0mol%-3.0mol%Y_(2)O_(3)were studied by pressure-less sintering.The experimental results show that the densification temperature of zirconia ceramics increases gradually with the decrease of Y_(2)O_(3)doping content by which decreases the sintering driving force due to the lower oxygen vacancy concentration of the systems.Furthermore,the bending strength and fracture toughness of the prepared zirconia ceramics increase with the decrease of Y_(2)O_(3)doping content.It can be attributed to the fact that the phase stability of tetragonal zirconia decreases with the decrease of Y_(2)O_(3)doping content,which is easier to induce"phase transformation toughening"and dissipate impact energy.The relative density,bending strength and fracture toughness of 2.0 mol%Y_(2)O_(3)doped zirconia ceramics(2.0Y-ZrO_(2))sintered at 1525℃are 99.00%,1256.65±20.82 MPa and 9.85±0.13 MPa·m^(1/2),respectively.

极薄氧化锆贴面的研究进展

全瓷贴面修复是改善牙齿形态、色泽和排列的常用方法。随着口腔陶瓷材料和修复体加工方式的不断发展,微创/无创贴面修复是医生和患者对牙齿修复提出的共同要求。本文回顾了全瓷贴面的发展历程和应用现状,对极薄氧化锆贴面相关的新材料、新工艺做一介绍,并对其技术前景和临床效果进行展望。

氧化锆和氧化镧共掺杂对堇青石多孔陶瓷性能的影响

为实现堇青石相的低温合成,采用粒度为≤0.044 mm的煅烧高岭土、粒度为≤0.074 mm的烧结镁砂和d_(50)=2.6μm的二氧化硅微粉为主要原料,以分析纯的氧化锆和氧化镧为烧结助剂,以聚乙烯醇PVA溶液为结合剂,按照堇青石理论配比,在60 MPa压力下成型为φ30 mm×30 mm的试样,干燥、煅烧后制备了堇青石多孔陶瓷。研究了烧结助剂氧化锆添加量(外加质量分数为0、8%)、氧化镧添加量(外加质量分数分别为0、0.2%、0.4%、0.6%、0.8%)和煅烧温度(分别为1200、1250及1300℃)对堇青石多孔陶瓷常温物理性能、物相组成和显微结构的影响。结果表明:1)在1300℃下,当试样中引入8%(w)氧化锆和0.6%(w)氧化镧时,试样的物理性能较优;2)氧化锆和氧化镧共掺杂可在显气孔率变化较小的情况下,提高试样的力学性能,且促进堇青石相的生成;3)氧化锆和氧化镧共掺杂可一定程度上降低堇青石相的合成温度,提高试样的综合性能。