Influences of shale microstructure on mechanical properties and bedding fractures distribution

The difference in microstructure leads to the diversity of shale mechanical properties and bedding fractures distribution patterns.In this paper,the microstructure and mechanical properties of Longmaxi marine shale and Qingshankou continental shale were studied by X-ray diffractometer(XRD),field emission scanning electron microscope(FE-SEM)with mineral analysis system,and nanoindentation.Additionally,the typical bedding layers area was properly stratified using Focused Ion Beam(FIB),and the effects of microstructure and mechanical properties on the distribution patterns of bedding fractures were analyzed.The results show that the Longmaxi marine shale sample contains more clay mineral grains,while the Qingshankou continental shale sample contains more hard brittle mineral grains such as feldspar.For Longmaxi marine shale sample,hard brittle minerals with grain sizes larger than 20μm is18.24%and those with grain sizes smaller than 20μm is 16.22%.For Qingshankou continental shale sample,hard brittle minerals with grain sizes larger than 20μm is 40.7%and those with grain sizes smaller than 20μm is 11.82%.In comparison to the Qingshankou continental shale sample,the Longmaxi marine shale sample has a lower modulus,hardness,and heterogeneity.Laminated shales are formed by alternating coarse-grained and fine-grained layers during deposition.The average single-layer thickness of Longmaxi marine shale sample is greater than Qingshankou continental shale sample.The two types of shale have similar bedding fractures distribution patterns and fractures tend to occur in the transition zone from coarse-grained to fine-grained deposition.The orientation of the fracture is usually parallel to the bedding plane and detour occurs in the presence of hard brittle grains.The fracture distribution density of the Longmaxi marine shale sample is lower than that of the Qingshankou continental shale sample due to the strong heterogeneity of the Qingshankou continental shale.The current research provides guidelines for the effective development of shale reservoirs in various sedimentary environments.

Tribological Behaviors of Electroless Nickel-Boron Coating on Titanium Alloy Surface

Titanium alloys are excellent structural materials in engineering fields,but their poor tribological properties limit their further applications.Electroless plating is an effective method to enhance the tribological performance of alloys,but it is difficult to efficiently apply to titanium alloys,due to titanium alloy’s strong chemical activity.In this work,the electroless Nickel-Boron(Ni-B)coating was successfully deposited on the surface of titanium alloy(Ti-6AL-4V)via a new pre-treatment process.Then,linearly reciprocating sliding wear tests were performed to evaluate the tribological behaviors of titanium alloy and its electroless Ni-B coatings.It was found that the Ni-B coatings can decrease the wear rate of the titanium alloy from 19.89×10^(−3)mm^(3)to 0.41×10^(−3)mm^(3),which attributes to the much higher hardness of Ni-B coatings.After heat treatment,the hardness of Ni-B coating further increases corresponding to coating crystallization and hard phase formation.However,heat treatment does not improve the tribological performance of Ni-B coating,due to the fact that higher brittleness and more severe oxidative wear exacerbate the damage of heat-treated coatings.Furthermore,the Ni-B coatings heat-treated both in air and nitrogen almost present the same tribological performance.The finding of this work on electroless coating would further extend the practical applications of titanium alloys in the engineering fields.

Mechanical Behavior Based on Aggregates Microstructure of Ultra-high Performance Concrete

We developed ultra-high performance concrete(UHPC)incorporating mullite sand and brown corundum sand(BCS),and the quartz sand UHPC was utilized to prepare for comparison.The properties of compressive strength,elastic modulus,ultrasonic pulse velocity,flexural strength,and toughness were investigated.Scanning electron microscopy and nanoindentation were also conducted to reveal the underlying mechanisms affecting macroscopic performance.Due to the superior interface bonding properties between mullite sand and matrix,the compressive strength and flexural toughness of UHPC have been significantly improved.Mullite sand and BCS aggregates have higher stiffness than quartz sand,contributing to the excellent elastic modulus exhibited by UHPC.The stiffness and volume of aggregates have a more significant impact on the elastic modulus of UHPC than interface performance,and the latter contributes more to the strength of UHPC.This study will provide a reference for developing UHPC with superior elastic modulus for structural engineering.

Temperature effect on nanotwinned Ni under nanoindentation using molecular dynamic simulation

Temperature effect on atomic deformation of nanotwinned Ni (nt-Ni) under localized nanoindentation is investigated in comparison with nanocrystalline Ni (nc-Ni) through molecular simulation.The nt-Ni exhibits enhanced critical load and hardness compared to nc-Ni,where perfect,stair-rod and Shockley dislocations are activated at (111),(111) and (111) slip planes in nt-Ni compared to only SSockley dislocation nucleation at (111) and (111) slip planes of nc-Ni.The nt-Ni exhibits a less significant indentation size effect in comparison with nc-Ni due to the dislocation slips hindrance of the twin boundary.The atomic deformation associated with the indentation size effect is investigated during dislocation transmission.Different from the decreasing partial slips parallel to the indenter surface in nc-Ni with increasing temperature,the temperaturedependent atomic deformation of nt-Ni is closely related to the twin boundary:from the partial slips parallel to the twin boundary (~10 K),to increased confined layer slips and decreased twin migration(300 K–600 K),to decreased confined layer slips and increased dislocation interaction of dislocation pinning and dissociation (900 K–1200 K).Dislocation density and atomic structure types through quantitative analysis are implemented to further reveal the above-mentioned dislocation motion and atomic structure alteration.Our study is helpful for understanding the temperature-dependent plasticity of twin boundary in nanotwinned materials.

Design multifunctional Mg–Zr coatings regulating Mg alloy bioabsorption

Magnesium(Mg)alloys are widely used for temporary bone implants due to their favorable biodegradability,cytocompatibility,hemocompatibility,and close mechanical properties to bone.However,rapid degradation and inadequate strength limit their applicability.To overcome this,the direct current magnetron sputtering technique is employed for surface coating in Mg-based alloys using various zirconium(Zr)content.This approach presents a promising strategy for simultaneously improving corrosion resistance,maintaining biocompatibility,and enhancing strength without compromising osseointegration.By leveraging Mg’s inherent biodegradability,it has the potential to minimize the need for secondary surgeries,thereby reducing costs and resources.This paper is a systematic study aimed at understanding the corrosion mechanisms of Mg–Zr coatings,denoted Mg-xZr(x=0–5 at.%).Zr-doped coatings exhibited columnar growth leading to denser and refined structures with increasing Zr content.XRD analysis confirmed the presence of the Mg(00.2)basal plane,shifting towards higher angles(1.15°)with 5 at.%Zr doping due to lattice parameter changes(i.e.,decrease and increase of“c”and“a”lattice parameters,respectively).Mg–Zr coatings exhibited“liquidphilic”behavior,while Young’s modulus retained a steady value around 80 GPa across all samples.However,the hardness has significantly improved across all samples’coating,reaching the highest value of(2.2±0.3)GPa for 5 at.%Zr.Electrochemical testing in simulated body fluid(SBF)at 37℃ revealed a significant enhancement in corrosion resistance for Mg–Zr coatings containing 1.0–3.4 at.%Zr.Compared with the 5 at.%Zr coating which exhibited a corrosion rate of 32 mm/year,these coatings displayed lower corrosion rates,ranging from 1 to 12 mm/year.This synergistic enhancement in mechanical properties and corrosion resistance,achieved with 2.0–3.4 at.%Zr,suggests potential ability for reducing stress shielding and controlled degradation performance,and consequently,promising functional biodegradable materials for temporary bone implants.

Correlation of work function and stacking fault energy through Kelvin probe force microscopy and nanohardness in diluteα-magnesium

Electronic interactions of the Group 2A elements with magnesium have been studied through the dilute solid solutions in binary Mg-Ca,Mg-Sr and Mg-Ba systems.This investigation incorporated the difference in the‘Work Function'(ΔWF)measured via Kelvin Probe Force Microscopy(KPFM),as a property directly affected by interatomic bond types,i.e.the electronic structure,nanoindentation measurements,and Stacking Fault Energy values reported in the literature.It was shown that the nano-hardness of the solid-solutionα-Mg phase changed in the order of Mg-Ca>Mg-Sr>Mg-Ba.Thus,it was shown,by also considering the nano-hardness levels,that SFE of a solid-solution is closely correlated with its‘Work Function'level.Nano-hardness measurements on the eutectics andΔWF difference between eutectic phases enabled an assessment of the relative bond strength and the pertinent electronic structures of the eutectics in the three alloys.Correlation withΔWF and at least qualitative verification of those computed SFE values with some experimental measurement techniques were considered important as those computational methods are based on zero Kelvin degree,relatively simple atomic models and a number of assumptions.As asserted by this investigation,if the results of measurement techniques can be qualitatively correlated with those of the computational methods,it can be possible to evaluate the electronic structures in alloys,starting from binary systems,going to ternary and then multi-elemental systems.Our investigation has shown that such a qualitative correlation is possible.After all,the SFE values are not treated as absolute values but rather become essential in comparative investigations when assessing the influences of alloying elements at a fundamental level,that is,free electron density distributions.Our study indicated that the principles of‘electronic metallurgy'in developing multi-elemental alloy systems can be followed via practical experimental methods,i.e.ΔWF measurements using KPFM and nanoindentation.

Overdischarge-induced evolution of Cu dendrites and degradation of mechanical properties in lithium-ion batteries

The degradation of mechanical properties of overdischarge battery materials manifests as a significant effect on the energy density,safety,and cycle life of the batteries.However,establishing the correlation between depth of overdischarge and mechanical properties is still a significant challenge.Studying the correlation between depth of overdischarge and mechanical properties is of great significance to improving the energy density and the ability to resist abuse of the batteries.In this paper,the mechanical properties of the battery materials during the whole process of overdischarge from discharge to complete failure were studied.The effects of depth of overdischarge on the elastic modulus and hardness of the cathode of the battery,the tensile strength and the thermal shrinkage rate of the separator,and the performance of binder were investigated.The precipitation of Cu dendrites on the separator and cathode after dissolution of anode copper foil is a key factor affecting the performance of battery materials.The Cu dendrites attached to the cathode penetrate the separator,causing irreversible damage to the coating and base film of the separator,which leads to a sharp decline in the tensile strength,thermal shrinkage rate and other properties of the separator.In addition,the Cu dendrites wrapping the cathode active particles reduce the adhesion of the active particles binder.Meanwhile,the active particles are damaged,resulting in a significant decrease in the elastic modulus and hardness of the cathode.

Investigation of point defect evolution and Voronoi cluster analysis for magnesium during nanoindentation

The present study investigates the effect of nanoindentation on single-crystal magnesium specimens using the embedded-atom method potential in molecular dynamics simulation.Analyses are done under dynamic loading where the load-bearing capacity and change in the structural configuration are studied on the basal(Z-direction)and two prismatic planes(X-and Y-directions)with varying indenter velocities.The investigation of structural evolution is done using atomic displacement analyses to measure the net magnitude of displacement,atomic strain analyses to evaluate the shear strain developed in the process,and Wigner-Seitz defect analyses to calculate the total vacancies at varied timesteps.Furthermore,Voronoi analyses are done when indented on the basal plane to identify the cluster distribution at different planar depths of the specimen.From the analyses,it has been observed that the load-bearing capacity of the specimen varies with the indentation velocity and the direction of indentation on the specimen.Additionally,it is seen that the observed shear and total atomic displacement in the Z-direction is the least in comparison to the other two axes.The partial dislocation 1/3<-12-10>is seen to be majorly present and the population of dislocation loops is more abundant for lower indenter velocities.Furthermore,clusters<0,4,4,6>and<0,6,0,8>are the major indices developed during nanoindentation on the basal plane where they exhibit symmetrical distribution as observed from the Z-direction.

Effects of coals microscale structural features on their mechanical properties,propensity to crushing and fine dust formation

The work is dedicated to revealing the structural features of coals with different ranks,such as anthracites,metaanthracite and graphite,that determine their ability to crush and form fine dust.For this purpose,a combination of various nanoin-dentation techniques and Raman spectroscopy was used.The mechanical behavior of the selected coals was investigated by cyclic nanoindentation with increasing peak load and quasi-static loading.The alteration of the mechanical properties was studied by analysis of elastic moduli and damage indices Rw.Three groups of coals were identified based on their propensity to crushing during cyclic nanoindentation.Coals assigned to the first and second groups are characterized by local destruction in the contact zone with the indenter and the formation of a core of crushed material.Coals assigned to the third group are characterized by bulk destruction(outside the zone of contact with the indenter).In general,the ability of coals to fracture under mechanical loading decreases in the series of metamorphism due to microscale compaction of vitrinite matter.In the series of anthracite,metaanthracite and graphite,it is established that the coal matter compaction takes place for the anthracite and metaanthracite,whereas graphite reveals rather different behavior due to abrupt change of its structure.The ratios between the amorphous and crystalline phases of carbon(S)were determined by deconvolution of coals Raman spectra.The propensity of coals to crushing(a damage index Rw)increases with growth of the proportion of amorphous carbon in the coal matter.For the considered coals and metaanthracite,it is established that the proneness to destruction outside the contact zone with the indenter is determined by the ratio of amorphous and crystalline carbon of 1 and higher.When S parameter is lower than 1,the coals are being crushed only in the zone of contact with the indenter.

In situ TEM observations and molecular dynamics simulations of deformation defect activities in Mg via nanoindentation

In this work, we performed in situ nanoindentation in TEM to capture the real-time dislocation and twinning activities in pure Mg during loading and unloading. We demonstrated that the screw component of dislocations glides continuously, while the edge components rapidly become sessile during loading. The twin tip propagation is intermittent, whereas the twin boundary migration is more continuous. During unloading, we observed the elastic strain relaxation causes both dislocation retraction and detwinning. Moreover,we note that the plastic zone comprised of dislocations in Mg is well-defined, which contrasts with the diffused plastic zones observed in face-centered cubic metals under the nanoindentation impressions. Additionally, molecular dynamics simulations were performed to study the formation and evolution of deformation-induced crystallographic defects at the early stages of indentation. We observed that,in addition to dislocations, the I1stacking fault bounded with a <1/2c+p> Frank loop can be generated from the plastic zone ahead of the indenter, and potentially serve as a nucleation source for abundant dislocations observed experimentally. These new findings are anticipated to provide new knowledge on the deformation mechanisms of Mg, which are difficult to obtain through conventional ex situ approaches. These observations may serve as a baseline for simulation work that investigate the dynamics of dislocation slip and twinning in Mg and alloys.

The Influence of Crystallographic Orientation and Grain Boundary on Nanoindentation Behavior of Inconel 718 Superalloy Based on Crystal Plasticity Theory

The crystal plasticity finite element method(CPFEM)is widely used to explore the microscopic mechanical behavior of materials and understand the deformation mechanism at the grain-level.However,few CPFEM simulation studies have been carried out to analyze the nanoindentation deformation mechanism of polycrystalline materials at the microscale level.In this study,a three-dimensional CPFEM-based nanoindentation simulation is performed on an Inconel 718 polycrystalline material to examine the influence of different crystallographic parameters on nanoindentation behavior.A representative volume element model is developed to calibrate the crystal plastic constitutive parameters by comparing the stress-strain data with the experimental results.The indentation force-displacement curves,stress distributions,and pile-up patterns are obtained by CPFEM simulation.The results show that the crystallographic orientation and grain boundary have little influence on the force-displacement curves of the nanoindentation,but significantly influence the local stress distributions and shape of the pile-up patterns.As the difference in crystallographic orientation between grains increases,changes in the pile-up patterns and stress distributions caused by this effect become more significant.In addition,the simulation results reveal that the existence of grain boundaries affects the continuity of the stress distribution.The obstruction on the continuity of stress distribution increases as the grain boundary angle increases.This research demonstrates that the proposed CPFEM model can well describe the microscopic compressive deformation behaviors of Inconel 718 under nanoindentation.

Stress distribution variations during nanoindentation failure of hard coatings on silicon substrates

Regarding quality inspection of technologically important nanocomposite hard coatings based on Ti,B,Si,C,and N and bioceramics such as hydroxyapatite that are used in small-scale high-precision devices and bio-implants,it is essential to study the failure mechanisms associated with nanoindentation,such as fracture,delamination,and chipping.The stress imposed by the indenter can affect the fracture morphology and the interfacial fracture energy,depending on indenter shape,substrate type,crystallographic properties,pre-existing flaws,internal microcracks,and pre-strain.Reported here are finite-element-based fracture studies that provide insights into the different cracking mechanisms related to the aforementioned failure process,showing that the fracture morphology is affected by the interaction of different cracking events.The interfacial fracture energy,toughness,and residual stress are calculated using existing models with minor adjustments,and it is found that increasing the indenter sharpness improves the shear stress distribution,making the coating more prone to separation.Depending on the prevailing type of stress,the stress distribution beneath the depression results in either crack formation or a dislocation pile-up leading to strain hardening.Different forms of resistances resulting from the indentation process are found to affect the tip–sample conduction,and because of its stronger induced plasticity than that of a Berkovich indenter tip,a sharper cube-corner tip produces more resistance.

Early-Age Properties Development of Recycled Glass Powder Blended Cement Paste:Strengths,Shrinkage,Nanoscale Characteristics,and Environmental Analysis

Recycling solid waste in cement-based materials cannot only ease its load on the natural environment but also reduce the carbon emissions of building materials.This study aims to investigate the effect of recycled glass powder(RGP)on the early-age mechanical properties and autogenous shrinkage of cement pastes,where cement is replaced by 10%,20%and 30%of RGP.In addition,the microstructure and nano-mechanical properties of cement paste with different RGP content and water to binder(W/B)ratio were also evaluated using SEM,MIP and nanoindentation techniques.The results indicate that the early-age autogenous shrinkage decreases with the increase of RGP content and W/B ratio.While the mechanical strength deteriorates due to the addition of RGP,it can be compensated by reducing the W/B ratio.Although the addition of RGP increases the total porosity of the hardened paste,it reduces the small size porosity(<50 nm).In addition,the proportions of different types of C-S-H are changed,and the volume fraction of porosity is increased,but that of hydration products of cement paste is reduced due to the incorporation of RGP.Besides its pozzolanic activity,the mitigated shrinkage deformation that RGP is generating in cement pastes is encouraging for its use as a novel supplementary cementitious material that reduces the early-age cracking risk of cement-based materials.Meanwhile,the life cycle assessments indicate that the RGP-cement component is an economical and eco-friendly novel engineering material.

Micro-mechanical properties of shale due to water/supercritical carbon dioxide-rock interaction

To investigate the impacts of water/supercritical CO_(2)-rock interaction on the micro-mechanical properties of shale,a series of high-temperature and high-pressure immersion experiments were performed on the calcareous laminated shale samples mined from the lower submember of the third member of Paleogene Shahejie Formation in the Jiyang Depression,Bohai Bay Basin.After that,grid nanoindentation tests were conducted to analyze the influence of immersion time,pressure,and temperature on micro-mechanical parameters.Experimental results show that the damage of shale caused by the water/supercritical CO_(2)-rock interaction was mainly featured by the generation of induced fractures in the clay-rich laminae.In the case of soaking with supercritical CO_(2),the aperture of induced fracture was smaller.Due to the existence of induced fractures,the statistical averages of elastic modulus and hardness both decreased.Meanwhile,compaction and stress-induced tensile fractures could be observed around the laminae.Generally,the longer the soaking time,the higher the soaking pressure and temperature,the more significant the degradation of micro-mechanical parameters is.Compared with water-rock interaction,the supercritical CO_(2)-rock interaction caused a lower degree of mechanical damage on the shale surface.Thus,supercritical CO_(2)can be used as a fracturing fluid to prevent the surface softening of induced fractures in shale reservoirs.

Residual elastic stress strain field and geometrically necessary dislocation density distribution around nano-indentation in TA15 titanium alloy

Nanoindentation and high resolution electron backscatter diffraction（EBSD） were combined to examine the elastic modulus and hardness of α and β phases,anisotropy in residual elastic stress strain fields and distributions of geometrically necessary dislocation（GND） density around the indentations within TA15 titanium alloy.The nano-indention tests were conducted on α and β phases,respectively.The residual stress strain fields surrounding the indentation were calculated through crosscorrelation method from recorded patterns.The GND density distribution around the indentation was calculated based on the strain gradient theories to reveal the micro-mechanism of plastic deformation.The results indicate that the elastic modulus and hardness for α p hase are 129.05 GPas and 6.44 GPa,while for β phase,their values are 109.80 GPa and 4.29 GPa,respectively.The residual Mises stress distribution around the indentation is relatively heterogeneous and significantly influenced by neighboring soft β phase.The region with low residual stress around the indentation is accompanied with markedly high a type and prismatic-GND density.

Mechanical properties of tungsten nanowhiskers characterized by nanoindentation

The Mechanical properties of the hexagonal tungsten nanowhiskers, which were synthesized by chemical vapor deposition, were characterized by instrumented nanoindentation and atomic force microscope （AFM）. The nanoindentation results show that tungsten nanowhiskers exhibit a hardness of （6.2±1.7） GPa and an elastic modulus of （225±20） GPa. According to the comparative test results, the tungsten nanowhiskers possess a comparable hardness to tungsten microwhiskers, and an hardness increase of 35% to the bulk single-crystal tungsten. The increase in the hardness of whiskers is attributed to the lacking of dislocation avalanche observed in the bulk single-crystal tungsten. The measured modulus is about 80% that of the tungsten microwhiskers, which can be contributed to the size effects of the nanowhiskers and the substrate effects in the nanoindentation test.

Theoretical prediction and experimental investigation on formability of tailor-welded blanks

Based on the elastoplastic mechanical properties of the weld and heat affected zone metals obtained by a nanoindentation test, a theoretical calculation model was established for the forming limit diagram（FLD） of tailor-welded blanks（TWBs） on the basis of plastic constitutive relations and Hosford yield criteria. Hemispherical punch bulging tests were performed to verify the FLD theoretical calculation results. The results demonstrated that not only the FLD theoretical calculation of base materials but also that of TWBs had a good agreement with their experiments. Besides, poorer formability of TWBs caused its FLD significantly lower than that of base materials. The theoretical calculation model offers a reliable approach to obtain the specific FLD of TWBs.

Comparison between the surface defects caused by Al_2O_3 and TiN inclusions in interstitial-free steel auto sheets

Al_2O_3 and TiN inclusions in interstitial-free(IF) steel deteriorate the properties of the steel. To decrease the defects of cold-rolled sheet, it is important to clearly distinguish between the degrees of damage caused by these two inclusions on the surface quality of the steel. In this study, a nanoindenter was used to test the mechanical properties of the inclusions, and the distribution and size of the inclusions were obtained by scanning electron microscopy(SEM). It was found that when only mechanical properties are considered, TiN inclusions are more likely to cause defects than Al_2O_3 inclusions of the same size during the rolling process. However, Al_2O_3 inclusions are generally more inclined to cause defects in the rolling process than TiN inclusions because of their distribution characteristic in the thickness direction. The precipitation of Al_2O_3 and TiN was obtained through thermodynamical calculations. The growth laws of inclusions at different cooling rates were calculated by solidification and segregation models. The results show that the precipitation regularity is closely related to the distribution law of the inclusions in IF slabs along the thickness direction.

Elastic modulus determination at different levels of periodontal ligament in nanoindentation

In order to investigate the material properties ofperiodontal ligament （ PDL） in different locations, the nanoindentation method is used to survey the elastic modulus of the PDL at different levels. Cadaveric specimens of human mandibular canine were obtained from 4 adult donors, 16 transverse specimens were made from the sections of cervical margin, midroot and apex using the slow cutting machine. The prepared specimens were tested in different sections （along the longitudinal direction） and different areas （in the circumferential direction）. According to the Oliver-Phair theory, the mean values of elastic modulus were calculated foreach area and the differences among them were compared. In the midroot section, the average elastic modulus is ranging from 0. 11 to 0. 23 MPa, the changing range of the cervical margin and apex are from 0. 21 to 0. 53 MPa and 0. 44 to0.62 MPa, respectively. Experimental results indicate that the average elastic modulus in the midroot is lower than that in the cervical margin and apex, and relatively small changes occur among them. However, there is a large change to the elastic modulus value in the cicumferential direction for the PDL.

Study on Microstructure and Nanoindentation of Antibacterial Bone China Film

Fracture surface and surface of two kind of films of antibacterial bone china with 3% and 5% composite phosphate containing rare earth were characterized by SEM and nanoindenter, respectively, and the hardness and elastic modulus were measured by nanoindenter at different load conditions. The results show that hardness and elastic modulus of the two kinds of films have obvious change. Elastic modulus versus maximal depth of indentation curves are almost linear. Hardness versus maximal depth of indentation of film with 5% rare earth content curve is nearly linear, while that of 3% increases at first, then decreases. Obvious pile-up of indentation impression of ceramic film with 3% rare earth content is observed with h_f/h_ max<0.7 and different loads, however indentation impression of 5% has no this kind of phenomenon. Special properties of two kinds of ceramic films are because that films are the mixture of crystal and non-crystal materials.