The N3 power plant of Taipower is located in the southern tip of Taiwan and connected to the power pool by four out-linking 345-kV overhead transmission circuits. There are two 951-MW generators. Each generator occupi...The N3 power plant of Taipower is located in the southern tip of Taiwan and connected to the power pool by four out-linking 345-kV overhead transmission circuits. There are two 951-MW generators. Each generator occupied 11% of the system peak load in 1985 when the generator was in commercial operation. Since Taipower is an isolated system, at the N-2 conditions, those generators were reduced to 75% loading to protect the power system. By the way, to avoid damage of negative sequence current (NSC), the limits of the N3 power plant are stricter than those in the IEEE Standard. However, in 2010, the capacity ratio of each generator in the plant to the system peak load has been reduced to 3% only. To increase the economic benefit of those generators, it is required to reassess the operation limits of NSC. EMTP was used to calculate the levels of NSC from the out-linking transmission circuits. From the results of this study, the effects of NSC could be ignored when the four out-linking circuits are in N-0, N-1, and N-2 conditions. The generators can be operated in full loading under these conditions. The modifications to the NSC limits of the N3 power plant are also suggested.展开更多
Voltage sag is one of the most common power quality disturbances in industry,which causes huge inrush currents in stator windings of induction motors,and adversely impacts the motor secure operation.This paper firstly...Voltage sag is one of the most common power quality disturbances in industry,which causes huge inrush currents in stator windings of induction motors,and adversely impacts the motor secure operation.This paper firstly introduces a 2D Time-Stepping multi-slice finite element method(2D T-S multi-slice FEM)which is used for calculating the magnetic field distribution in induction motors under different sag events.Then the paper deduces the transient analytical expression of stator inrush current based on the classical theory of AC motors and presents a separation method for the positive,negative and zero sequence values based on instantaneous currents.With this method,the paper studies the influences of voltage sag amplitude,phase-angle jump and initial phase angle on the stator positive-and negative-sequence peak currents of 5.5 kW and 55 kW induction motors.This paper further proposes a motor protection method under voltage sag condition with the stator negative-sequence peak currents as the protection threshold,so that the protection false trip can be avoided effectively.Finally,the calculation and analysis results are validated by the comparison of calculated and measured stator peak value of the 5.5 kW induction motor.展开更多
基于使用智能插座对电路中的电流高频次监测、获得用户用电态势数据,对电流迁移态序列、电流迁移态序列特征的一元回归模型进行了研究.基于电流稳态序列ε片段、电流稳态序列片段,设计了电流迁移态序列的构造方法,提出使用一元回归模型...基于使用智能插座对电路中的电流高频次监测、获得用户用电态势数据,对电流迁移态序列、电流迁移态序列特征的一元回归模型进行了研究.基于电流稳态序列ε片段、电流稳态序列片段,设计了电流迁移态序列的构造方法,提出使用一元回归模型描述每一个电流迁移态序列,实现将长度不定的电流迁移态序列到维数固定的电流迁移态序列特征空间的映射.进一步,设计了基于微环境的粒子群优化算法(Microenvironment based Particle Swarm Optimization,MPSO),实现了电流迁移态序列一元回归特征的优化.实验表明:使用所提电流迁移态序列特征进行电器状态识别,平均可以达到97.93%的准确率,且相较PSO算法与CAPSO算法,MPSO算法在使用较少的粒子数达到与这两种算法一致精度的同时,使用时间显著降低.展开更多
针对逆变侧交流故障下高压直流(line commutated converter-high voltage direct current,LCC-HVDC)输电系统易引发连续换相失败问题,该文分阶段分析了连续换相失败的产生机理。明确了当产生触发角偏差后,直流电流调节效果与实际触发角...针对逆变侧交流故障下高压直流(line commutated converter-high voltage direct current,LCC-HVDC)输电系统易引发连续换相失败问题,该文分阶段分析了连续换相失败的产生机理。明确了当产生触发角偏差后,直流电流调节效果与实际触发角不匹配是连续换相失败的重要诱因。同时不对称故障后,负序分量通过极控、阀控两级控制系统对实际触发角造成的影响,增加连续换相失败的风险。因此提出了一种基于实际触发角响应的连续换相失败抑制方法,通过实际触发角修正整流侧电流指令值。与此同时,该方法通过陷波器降低负序电流对极控层触发角指令值的影响,通过相序解耦控制器和换相电压相位补偿降低负序电压对阀控层触发角实际值的影响。该方法能实现动态、自适应的电流指令值调整,提升恢复过程中直流电流与实际触发角的匹配度,提升直流系统抵御连续换相失败能力。在CIGRE标准测试模型和实际工程模型中,验证了理论分析的正确性和优化方法的有效性。展开更多
文摘The N3 power plant of Taipower is located in the southern tip of Taiwan and connected to the power pool by four out-linking 345-kV overhead transmission circuits. There are two 951-MW generators. Each generator occupied 11% of the system peak load in 1985 when the generator was in commercial operation. Since Taipower is an isolated system, at the N-2 conditions, those generators were reduced to 75% loading to protect the power system. By the way, to avoid damage of negative sequence current (NSC), the limits of the N3 power plant are stricter than those in the IEEE Standard. However, in 2010, the capacity ratio of each generator in the plant to the system peak load has been reduced to 3% only. To increase the economic benefit of those generators, it is required to reassess the operation limits of NSC. EMTP was used to calculate the levels of NSC from the out-linking transmission circuits. From the results of this study, the effects of NSC could be ignored when the four out-linking circuits are in N-0, N-1, and N-2 conditions. The generators can be operated in full loading under these conditions. The modifications to the NSC limits of the N3 power plant are also suggested.
基金This work was supported in part by the National Natural Science Foundation of China under Grant51307050。
文摘Voltage sag is one of the most common power quality disturbances in industry,which causes huge inrush currents in stator windings of induction motors,and adversely impacts the motor secure operation.This paper firstly introduces a 2D Time-Stepping multi-slice finite element method(2D T-S multi-slice FEM)which is used for calculating the magnetic field distribution in induction motors under different sag events.Then the paper deduces the transient analytical expression of stator inrush current based on the classical theory of AC motors and presents a separation method for the positive,negative and zero sequence values based on instantaneous currents.With this method,the paper studies the influences of voltage sag amplitude,phase-angle jump and initial phase angle on the stator positive-and negative-sequence peak currents of 5.5 kW and 55 kW induction motors.This paper further proposes a motor protection method under voltage sag condition with the stator negative-sequence peak currents as the protection threshold,so that the protection false trip can be avoided effectively.Finally,the calculation and analysis results are validated by the comparison of calculated and measured stator peak value of the 5.5 kW induction motor.
文摘基于使用智能插座对电路中的电流高频次监测、获得用户用电态势数据,对电流迁移态序列、电流迁移态序列特征的一元回归模型进行了研究.基于电流稳态序列ε片段、电流稳态序列片段,设计了电流迁移态序列的构造方法,提出使用一元回归模型描述每一个电流迁移态序列,实现将长度不定的电流迁移态序列到维数固定的电流迁移态序列特征空间的映射.进一步,设计了基于微环境的粒子群优化算法(Microenvironment based Particle Swarm Optimization,MPSO),实现了电流迁移态序列一元回归特征的优化.实验表明:使用所提电流迁移态序列特征进行电器状态识别,平均可以达到97.93%的准确率,且相较PSO算法与CAPSO算法,MPSO算法在使用较少的粒子数达到与这两种算法一致精度的同时,使用时间显著降低.
文摘针对逆变侧交流故障下高压直流(line commutated converter-high voltage direct current,LCC-HVDC)输电系统易引发连续换相失败问题,该文分阶段分析了连续换相失败的产生机理。明确了当产生触发角偏差后,直流电流调节效果与实际触发角不匹配是连续换相失败的重要诱因。同时不对称故障后,负序分量通过极控、阀控两级控制系统对实际触发角造成的影响,增加连续换相失败的风险。因此提出了一种基于实际触发角响应的连续换相失败抑制方法,通过实际触发角修正整流侧电流指令值。与此同时,该方法通过陷波器降低负序电流对极控层触发角指令值的影响,通过相序解耦控制器和换相电压相位补偿降低负序电压对阀控层触发角实际值的影响。该方法能实现动态、自适应的电流指令值调整,提升恢复过程中直流电流与实际触发角的匹配度,提升直流系统抵御连续换相失败能力。在CIGRE标准测试模型和实际工程模型中,验证了理论分析的正确性和优化方法的有效性。
