Hard coal is an important source of energy worldwide.Owing to the imperfections of excavation technology,most run-of-mine coals must be processed before they can be utilised as fuel.In this study,tests on the dry sepa...Hard coal is an important source of energy worldwide.Owing to the imperfections of excavation technology,most run-of-mine coals must be processed before they can be utilised as fuel.In this study,tests on the dry separation process were performed with numerous different raw hard coal and coal waste material samples,using a newly designed and constructed negative-pressure pneumatic separator(NPPS).The experiments revealed the effects of the feed-material properties and material processing conditions.These experiments were preceded by additional tests for evaluating the influence of each device operating parameter on the process,to determine the optimal method of supplying the feed material.The calorific value of the processed materials was improved by 5%–40%,while a minimal output yield of products(60%–70%)was maintained.The trials indicated that in coal material processing,the developed NPPS can be used for not only raw coal enrichment but also coal recovery from materials stored at coal-waste dumps.The main advantages of the device are its mobility,low material processing cost,and lack of water consumption during operation.展开更多
In particulate material transfer systems,traditional shear test based steady state analysis can provide some insight into the strength of the bulk material and subsequent resistive frictional forces during flow.For fa...In particulate material transfer systems,traditional shear test based steady state analysis can provide some insight into the strength of the bulk material and subsequent resistive frictional forces during flow.For fast flowing transfer points,dynamic flow conditions dominate and additional modelling techniques are required to improve design guidance.The research presented shows the evolution of a design solution which utilises two distinct processes;a continuum method and a discrete element method(DEM). Initially,the internal structure of dense granular flow,down vertical and inclined pipes was investigated using a twin sensor,12 electrode electrical capacitance tomography device.Subsequently,DEM simulations were conducted using the commercial software,PFC3D.Initially,two particle types and their flow behaviours were analysed:plastic pellets and sand.The pipe angle was varied between 0°and 45°to the vertical.For both the plastic pellets and the sand,good qualitative agreement was found with the spatial particle concentration analysis.Generally,the flow had a dense particle region at its core with the particle concentration reducing away from this core.As expected,at 0°, the core was centrally located within the pipe for both the plastic pellets and sand.At pipe angles 5°or greater,the dense core of particles was located on or near the pipe wall.Average flow velocity analysis was also conducted using the results of wall friction test analysis.The velocity comparisons also showed good agreement between the ECT image analysis and the DEM simulations. Subsequently,the DEM method was used to analyse a complex transfer system(or chute) with the continuum method providing comparative flow analysis with the DEM flow analysis.展开更多
基金The research presented in this paper was performed as a part of the Project AMSEP“Novel dry sorter for coal processing and coal recovery from mine originating wastes”,which was conducted with a financial grant from the European Institute of Innovation and Technology in frame of InnoEnergy S.E.,with Central Mining Institute as the Project coordinator.It was also financially supported by Statutory Research No.11325018-173.
文摘Hard coal is an important source of energy worldwide.Owing to the imperfections of excavation technology,most run-of-mine coals must be processed before they can be utilised as fuel.In this study,tests on the dry separation process were performed with numerous different raw hard coal and coal waste material samples,using a newly designed and constructed negative-pressure pneumatic separator(NPPS).The experiments revealed the effects of the feed-material properties and material processing conditions.These experiments were preceded by additional tests for evaluating the influence of each device operating parameter on the process,to determine the optimal method of supplying the feed material.The calorific value of the processed materials was improved by 5%–40%,while a minimal output yield of products(60%–70%)was maintained.The trials indicated that in coal material processing,the developed NPPS can be used for not only raw coal enrichment but also coal recovery from materials stored at coal-waste dumps.The main advantages of the device are its mobility,low material processing cost,and lack of water consumption during operation.
文摘In particulate material transfer systems,traditional shear test based steady state analysis can provide some insight into the strength of the bulk material and subsequent resistive frictional forces during flow.For fast flowing transfer points,dynamic flow conditions dominate and additional modelling techniques are required to improve design guidance.The research presented shows the evolution of a design solution which utilises two distinct processes;a continuum method and a discrete element method(DEM). Initially,the internal structure of dense granular flow,down vertical and inclined pipes was investigated using a twin sensor,12 electrode electrical capacitance tomography device.Subsequently,DEM simulations were conducted using the commercial software,PFC3D.Initially,two particle types and their flow behaviours were analysed:plastic pellets and sand.The pipe angle was varied between 0°and 45°to the vertical.For both the plastic pellets and the sand,good qualitative agreement was found with the spatial particle concentration analysis.Generally,the flow had a dense particle region at its core with the particle concentration reducing away from this core.As expected,at 0°, the core was centrally located within the pipe for both the plastic pellets and sand.At pipe angles 5°or greater,the dense core of particles was located on or near the pipe wall.Average flow velocity analysis was also conducted using the results of wall friction test analysis.The velocity comparisons also showed good agreement between the ECT image analysis and the DEM simulations. Subsequently,the DEM method was used to analyse a complex transfer system(or chute) with the continuum method providing comparative flow analysis with the DEM flow analysis.
