Fluidized reduction roasting is an efficient metallurgical technique.However,its application to nickel laterite ore has rarely been reported.In this paper,the effects of reduction temperature,reduction time,CO concent...Fluidized reduction roasting is an efficient metallurgical technique.However,its application to nickel laterite ore has rarely been reported.In this paper,the effects of reduction temperature,reduction time,CO concentration,and material particle size on the roasting characteristics of ferronickel fluidization reduction were investigated.Combined with X-ray diffraction,scanning electron microscopy-energy dispersive spectrometry(SEM-EDS)characterization,the mineral phases and microscopic morphology of nickel laterite ore and its roasted ores were analyzed in depth.The results indicated that under the condition of a CO/CO_(2)ratio of 1:1,a reduction temperature of 800℃,and a reduction roasting time of 60 min,a nickel-iron concentrate with a nickel grade of 2.10%and an iron content of 45.96%was produced from a raw material with a nickel grade of 1.45%,achieving a remarkable nickel recovery rate of 46.26%.XRD and SEM-EDS analysis indicated that nickel in the concentrate mainly exists in the form of[Fe,Ni],while the unrecovered nickel in the tailings is primarily present in the form of[Fe,Ni]and Ni_(2)SiO_(4)in forsterite.This study established a theoretical foundation for further exploration of fluidized reduction roasting technology.展开更多
Fine nickel ferrite precursors NiFe2（C204）3·6H2O were obtained via co-precipitation method with low grade nickel matte as the raw material. Thermodynamic analysis of NiClz-FeC12-（NH4）2C204-H20 system for prec...Fine nickel ferrite precursors NiFe2（C204）3·6H2O were obtained via co-precipitation method with low grade nickel matte as the raw material. Thermodynamic analysis of NiClz-FeC12-（NH4）2C204-H20 system for precipitation identified that the theoretical optimum co-precipitation pH value is 2, and C2O2 has strong complexation with Ni2＋ and Fe2＋ ions. Based on these theoretical considerations, the effects of parameters on the precipitation rates and precursors size were investigated systematically. The results show that the optimum co-precipitation conditions are pH=2, temperature 45 ℃, 1.2 times theoretical amount of （NH4）2C204 dosage and 3% PEG400 addition. Under these conditions, the precipitation rates of Ni2＋ and Fe2＋ are both over 99.8%, with the precursors size of 1-2 urn. Furthermore, X-ray diffraction （XRD） and thermogravimetry-differential thermal analysis （TG-DTA） demonstrate that the precursors are single-phase solid solution, wherein the nickel/iron atoms are replaced by the iron/nickel atoms reciprocally.展开更多
Based on the process of coal-based self-reduction and melting separation at high temperature, it was investigated that the effect of process factors on the reduction of iron and nickel oxide, the metal yield and the n...Based on the process of coal-based self-reduction and melting separation at high temperature, it was investigated that the effect of process factors on the reduction of iron and nickel oxide, the metal yield and the nickel content in ferronickel about the laterite nickel ore, was from Philippines and contented low nickel, high iron and aluminum. The results showed that if the C/O mole ratio was not higher than 0.5 and the reduction temperature was kept as 1200°C and then increased up to 1500°C, the metal could not separate from molten slag for the A series of experiments, which were only added CaF<sub>2</sub>. However, when the C/O ratio was added up to 0.6 - 0.8, the metal could separate well from the slag, and the yields of Fe and Ni increased gradually. But the nickel content in the metal declined from 1.79% to 1.34%. When the C/O ratio increased to 1.2, and the temperature of melting products obtained at 1200°C and rose to 1550°C, the separation of metal from slag could not be realized in B group of tests, which were only added hydrated lime. However, when both of CaF<sub>2</sub> and hydrated lime were added, the metal could separate from slag in C group. In order to increase the content of nickel in the metal, it is necessary to restrain the reduction of iron oxide. When the C/O mole ratio is 0.6, the nickel content of metal could be 1.79%, which was higher than the theoretical ratio 1.65% of Ni/(Ni + Fe) of the latcritic nickel ore, but the yield of nickle was only 71.3%.展开更多
基金Project(XDA 29020100)supported by the Strategic Priority Research Program of the Chinese Academy of SciencesProject(2022YFE0206600)supported by National Key R&D Program of China。
文摘Fluidized reduction roasting is an efficient metallurgical technique.However,its application to nickel laterite ore has rarely been reported.In this paper,the effects of reduction temperature,reduction time,CO concentration,and material particle size on the roasting characteristics of ferronickel fluidization reduction were investigated.Combined with X-ray diffraction,scanning electron microscopy-energy dispersive spectrometry(SEM-EDS)characterization,the mineral phases and microscopic morphology of nickel laterite ore and its roasted ores were analyzed in depth.The results indicated that under the condition of a CO/CO_(2)ratio of 1:1,a reduction temperature of 800℃,and a reduction roasting time of 60 min,a nickel-iron concentrate with a nickel grade of 2.10%and an iron content of 45.96%was produced from a raw material with a nickel grade of 1.45%,achieving a remarkable nickel recovery rate of 46.26%.XRD and SEM-EDS analysis indicated that nickel in the concentrate mainly exists in the form of[Fe,Ni],while the unrecovered nickel in the tailings is primarily present in the form of[Fe,Ni]and Ni_(2)SiO_(4)in forsterite.This study established a theoretical foundation for further exploration of fluidized reduction roasting technology.
基金Project(2012BAB10B04) supported by National Key Technology R&D Program of ChinaProject supported by Hunan Provincial Innovation Foundation for Postgraduate,China
文摘Fine nickel ferrite precursors NiFe2（C204）3·6H2O were obtained via co-precipitation method with low grade nickel matte as the raw material. Thermodynamic analysis of NiClz-FeC12-（NH4）2C204-H20 system for precipitation identified that the theoretical optimum co-precipitation pH value is 2, and C2O2 has strong complexation with Ni2＋ and Fe2＋ ions. Based on these theoretical considerations, the effects of parameters on the precipitation rates and precursors size were investigated systematically. The results show that the optimum co-precipitation conditions are pH=2, temperature 45 ℃, 1.2 times theoretical amount of （NH4）2C204 dosage and 3% PEG400 addition. Under these conditions, the precipitation rates of Ni2＋ and Fe2＋ are both over 99.8%, with the precursors size of 1-2 urn. Furthermore, X-ray diffraction （XRD） and thermogravimetry-differential thermal analysis （TG-DTA） demonstrate that the precursors are single-phase solid solution, wherein the nickel/iron atoms are replaced by the iron/nickel atoms reciprocally.
文摘Based on the process of coal-based self-reduction and melting separation at high temperature, it was investigated that the effect of process factors on the reduction of iron and nickel oxide, the metal yield and the nickel content in ferronickel about the laterite nickel ore, was from Philippines and contented low nickel, high iron and aluminum. The results showed that if the C/O mole ratio was not higher than 0.5 and the reduction temperature was kept as 1200°C and then increased up to 1500°C, the metal could not separate from molten slag for the A series of experiments, which were only added CaF<sub>2</sub>. However, when the C/O ratio was added up to 0.6 - 0.8, the metal could separate well from the slag, and the yields of Fe and Ni increased gradually. But the nickel content in the metal declined from 1.79% to 1.34%. When the C/O ratio increased to 1.2, and the temperature of melting products obtained at 1200°C and rose to 1550°C, the separation of metal from slag could not be realized in B group of tests, which were only added hydrated lime. However, when both of CaF<sub>2</sub> and hydrated lime were added, the metal could separate from slag in C group. In order to increase the content of nickel in the metal, it is necessary to restrain the reduction of iron oxide. When the C/O mole ratio is 0.6, the nickel content of metal could be 1.79%, which was higher than the theoretical ratio 1.65% of Ni/(Ni + Fe) of the latcritic nickel ore, but the yield of nickle was only 71.3%.
