Electric vibrators find wide applications in reliability testing, waveform generation, and vibration simulation, making their noise characteristics a topic of significant interest. While Variational Mode Decomposition...Electric vibrators find wide applications in reliability testing, waveform generation, and vibration simulation, making their noise characteristics a topic of significant interest. While Variational Mode Decomposition (VMD) and Empirical Wavelet Transform (EWT) offer valuable support for studying signal components, they also present certain limitations. This article integrates the strengths of both methods and proposes an enhanced approach that integrates VMD into the frequency band division principle of EWT. Initially, the method decomposes the signal using VMD, determining the mode count based on residuals, and subsequently employs EWT decomposition based on this information. This addresses mode aliasing issues in the original method while capitalizing on VMD’s adaptability. Feasibility was confirmed through simulation signals and ultimately applied to noise signals from vibrators. Experimental results demonstrate that the improved method not only resolves EWT frequency band division challenges but also effectively decomposes signal components compared to the VMD method.展开更多
As vibration-based structural damage detection methods are easily affected by environmental noise, a new statistie-based noise analysis method is proposed together with the Monte Carlo technique to investigate the inf...As vibration-based structural damage detection methods are easily affected by environmental noise, a new statistie-based noise analysis method is proposed together with the Monte Carlo technique to investigate the influence of experimental noise of modal data on sensitivity-based damage detection methods. Different from the com- monly used random perturbation technique, the proposed technique is deduced directly by Moore-Pen"ose generalized inverse of the sensitivity matrix, which does not only make the analysis process more efficient but also can analyze the influence of noise on both frequencies and mode shapes for three commonly used sensitivity-based damage detection methods in a similar way. A one-story portal frame is adopted to evaluate the efficiency of the proposed noise analysis technique.展开更多
A distributed feedback fiber laser (DFB FL) sensor system with ultra-high resolution is described. The sensor is made by writing distributed feedback structures into a high gain active fiber, and the system employs ...A distributed feedback fiber laser (DFB FL) sensor system with ultra-high resolution is described. The sensor is made by writing distributed feedback structures into a high gain active fiber, and the system employs an unbalanced Michelson interferometer to translate laser wavelength shifts induced by weak measurands into phase shifts. A digital phase generated carrier demodulation scheme is introduced to achieve ultra-high resolution interrogation. A detailed noise analysis of the system is presented, and it is shown that the system resolution is limited by the frequency noise of the DFB FL.展开更多
The corrosion behavior of pure copper electrode exposed to artificial seawater has been studied using electrochemical noise analysis (ENA) and electrochemical impedance spectroscopy (EIS). A diffusion process was ...The corrosion behavior of pure copper electrode exposed to artificial seawater has been studied using electrochemical noise analysis (ENA) and electrochemical impedance spectroscopy (EIS). A diffusion process was observed for copper exposed to chloride media as indicated by the presence of a minimum phase angle over the lowest frequency range in the impedance plots. Analysis of electrochemical noise (EN) data has been collected both in time and frequency domains. Noise resistance Rn was obtained after analyzing EN data in the time domain. A good agreement was observed between Rn values and polarization resistance Rp values obtained from EIS analysis. Localization index Ii was not found to provide information concerning corrosion mechanisms. Also skewness and kurtosis for both potential and current fluctuations did not show any mechanistic information. It was concluded that ENA could detect the corrosion rate for copper exposed to chloride media, but was not found to provide information about the corrosion mechanisms.展开更多
A single-loop fourth-order sigma-delta(ΣΔ) interface circuit for a closed-loop micromachined accelerometer is presented.Two additional electronic integrators are cascaded with the micromachined sensing element to ...A single-loop fourth-order sigma-delta(ΣΔ) interface circuit for a closed-loop micromachined accelerometer is presented.Two additional electronic integrators are cascaded with the micromachined sensing element to form a fourth-order loop filter.The three main noise sources affecting the overall system resolution of aΣΔaccelerometer, mechanical noise,electronic noise and quantization noise,are analyzed in detail.Accurate mathematical formulas for electronic and quantization noise are established.The ASIC is fabricated in a 0.5μm two-metal two-poly n-well CMOS process.The test results indicate that the mechanical noise and electronic noise are 1μg/(Hz)^(1/2) and 8μV/(Hz)^(1/2) respectively,and the theoretical models of electronic and quantization noise agree well with the test and simulation results.展开更多
With lower turbulence and less rigorous restrictions on noise levels,offshore wind farms provide favourable conditions for the development of high-tip-speed wind turbines.In this study,the multi-objective optimization...With lower turbulence and less rigorous restrictions on noise levels,offshore wind farms provide favourable conditions for the development of high-tip-speed wind turbines.In this study,the multi-objective optimization is presented for a 5MW wind turbine design and the effects of high tip speed on power output,cost and noise are analysed.In order to improve the convergence and efficiency of optimization,a novel type of gradient-based multi-objective evolutionary algorithm is proposed based on uniform decomposition and differential evolution.Optimization examples of the wind turbines indicate that the new algorithm can obtain uniformly distributed optimal solutions and this algorithm outperforms the conventional evolutionary algorithms in convergence and optimization efficiency.For the 5MW wind turbines designed,increasing the tip speed can greatly reduce the cost of energy(COE).When the tip speed increases from 80m/s to 100m/s,under the same annual energy production,the COE decreases by 3.2%in a class I wind farm and by 5.1%in a class III one,respectively,while the sound pressure level increases by a maximum of 4.4dB with the class III wind farm case.展开更多
To analyze the security of two-step quantum direct communication protocol (QDCP) by using Einstein-Podolsky Rosen pair proposed by Deng et al. [Phys. Rev. A 68 (2003)042317] in collective-rotation noise channel, a...To analyze the security of two-step quantum direct communication protocol (QDCP) by using Einstein-Podolsky Rosen pair proposed by Deng et al. [Phys. Rev. A 68 (2003)042317] in collective-rotation noise channel, an excellent model of noise analysis is proposed. In the security analysis, the method of the entropy theory is introduced, and is compared with QDCP, an error rate point Qo(M : (Q0, 1.0)) is given. In different noise levels, if Eve wants to obtain the same amount of information, the error rate Q is distinguishable. The larger the noise level ~ is, the larger the error rate Q is. When the noise level ~ is lower than 11%, the high error rate is 0.153 without eavesdropping. Lastly, the security of the proposed protocol is discussed. It turns out that the quantum channel will be safe when Q 〈 0.153. Similarly, if error rate Q〉 0.153 = Q0, eavesdropping information I 〉 1, which means that there exist eavesdroppers in the quantum channel, and the quantum channel will not be safe anymore.展开更多
This study focuses on a single-stage axial flow fan, investigating the effect of three kinds of wave leading edge stator blades on its noise reduction. The DDES method and the duct acoustic analogy theory based on the...This study focuses on a single-stage axial flow fan, investigating the effect of three kinds of wave leading edge stator blades on its noise reduction. The DDES method and the duct acoustic analogy theory based on the penetrable data surface were used for noise prediction. The results showed that the three kinds of wave leading edge blades were effective in reducing the rotor-stator interaction tonal noise and also have a certain inhibitory effect on broadband noise. The A10W15 stator blade can effectively reduce broadband noise in the frequency range of 2200 - 4200 Hz. When the amplitude is increased to 20, the noise reduction effect is further enhanced. However, when the amplitude is increased to 30, the broadband noise reduction effect is no longer significant. Further research shows that the wave leading edge stator blades can significantly change the pressure fluctuation distribution on the leading edge and suction surface, which control the modal energy distribution. Finally, this paper analyzed multiple factors affecting the broadband noise reduction, such as the noise source cut-off and cut-on effect and correlation. The purpose of this paper is to explore the laws of the influence of wave leading edge blades on the duct noise of real fan, and to reveal its noise control mechanism. .展开更多
This paper presents Part II of a review on DFACS,which specifically focuses on the modeling and analysis of disturbances and noises in DFACSs.In Part I,the system composition and dynamics model of the DFACS were prese...This paper presents Part II of a review on DFACS,which specifically focuses on the modeling and analysis of disturbances and noises in DFACSs.In Part I,the system composition and dynamics model of the DFACS were presented.In this paper,we discuss the effects of disturbance forces and noises on the system,and summarize various analysis and modeling methods for these interferences,including the integral method,frequency domain analysis method,and magnitude evaluation method.By analyzing the impact of disturbances and noises on the system,the paper also summarizes the system’s performance under slight interferences.Additionally,we highlight current research difficulties in the field of DFACS noise analysis.Overall,this paper provides valuable insights into the modeling and analysis of disturbances and noises in DFACSs,and identifies key areas for future research.展开更多
Under the framework of white noise analysis, the existence of scattering solutions to the abstract dynamical φ4^4 wave equations in terms of generalized operators (see Section 3 below) is proven via a combination o...Under the framework of white noise analysis, the existence of scattering solutions to the abstract dynamical φ4^4 wave equations in terms of generalized operators (see Section 3 below) is proven via a combination of the characterization for the symbol of generalized operators and the classical scattering results. In addition, some properties (Poincare invariance and irreducibility) of the solutions are discussed.展开更多
The relation between generalized operators and operator-valued distributions is discussed so that these two viewpoints can be used alternatively to explain quantum fields.
The velocities of tectonic plates derived from GNSS time series are regularly used as input data for geophysical models. However, as shown by numerous researches, the coordinates time series contain residual errors of...The velocities of tectonic plates derived from GNSS time series are regularly used as input data for geophysical models. However, as shown by numerous researches, the coordinates time series contain residual errors of a systematic nature, which can significantly affect the reliability of the obtained velocity estimates. This research shows that using non-classical error theory of measurement(NETM)for processing GNSS time series allows detecting the presence of weak, not removed from GNSS processing, sources of systematic errors. Based on the coordinate time series of selected permanent GNSS stations in Europe, we checked the empirical distributions of errors by the NETM on G. Jeffries’ recommendations and on the principles of the theory of hypothesis tests according to Pearson’s criterion. It is established that the obtained coordinates time series of GNSS-stations only partially confirm the hypothesis of their conformity to the normal Gaussian distribution law, and this may be the main reason for their unrepresentative classification. In the future, it is necessary to identify and take into account the causes of residual errors that distort the real distribution of the results of the GNSS time series.展开更多
Optical buffers are critical for optical signal processing in future optical packet-switched networks. In this paper, a theoretical study as well as an experimental demonstration on a new optical buffer with large dyn...Optical buffers are critical for optical signal processing in future optical packet-switched networks. In this paper, a theoretical study as well as an experimental demonstration on a new optical buffer with large dynamical delay time is carried out based on cascaded double loop optical buffers (I:)LOBs). It is found that pulse distortion can be restrained by a negative optical control mode when the optical packet is in the loop. Noise analysis indicates that it is feasible to realise a large variable delay range by cascaded DLOBs. These conclusions are validated by the experiment system with 4-stage cascaded DLOBs. Both the theoretical simulations and the experimental results indicate that a large delay range of 1-9999 times the basic delay unit and a fine granularity of 25 ns can be achieved by the cascaded DLOBs. The performance of the cascaded DLOBs is suitable for the all optical networks.展开更多
An optimized structure to weaken the vibration and noise of a new asymmetric permanent magnet-assisted synchronous reluctance motor(PMaSynRM)is proposed.The new asymmetric PMaSynRM has the advantages of a low torque r...An optimized structure to weaken the vibration and noise of a new asymmetric permanent magnet-assisted synchronous reluctance motor(PMaSynRM)is proposed.The new asymmetric PMaSynRM has the advantages of a low torque ripple and high fault tolerance.However,the asymmetric structure generates an unbalanced magnetic force(UMF),which results in vibration and noise problems.In this study,the vibration and noise of the motor are analyzed and optimized.First,the radial pressure is analyzed,and an optimized structure is proposed.The electromagnetic performance of the motor before and after optimization is analyzed using the finite element method.Second,a three-dimensional model is established,and modal analysis is conducted considering the orthotropy of the stator and effective windings.Finally,the vibration and noise are simulated and analyzed,and the validity of the analysis results is verified experimentally.The analysis results indicate that the optimized motor realizes a reduction in the motor vibration and noise.展开更多
The dynamic parameters of a roller rig vary as the adhesion level changes.The change in dynamics parameters needs to be analysed to estimate the adhesion level.One of these parameters is noise emanating from wheel–ra...The dynamic parameters of a roller rig vary as the adhesion level changes.The change in dynamics parameters needs to be analysed to estimate the adhesion level.One of these parameters is noise emanating from wheel–rail interaction.Most previous wheel–rail noise analysis has been conducted to mitigate those noises.However,in this paper,the noise is analysed to estimate the adhesion condition at the wheel–rail contact interface in combination with the other methodologies applied for this purpose.The adhesion level changes with changes in operational and environmental factors.To accurately estimate the adhesion level,the influence of those factors is included in this study.The testing and verification of the methodology required an accurate test prototype of the roller rig.In general,such testing and verification involve complex experimental works required by the intricate nature of the adhesion process and the integration of the different subsystems(i.e.controller,traction,braking).To this end,a new reduced-scale roller rig is developed to study the adhesion between wheel and rail roller contact.The various stages involved in the development of such a complex mechatronics system are described in this paper.Furthermore,the proposed brake control system was validated using the test rig under various adhesion conditions.The results indicate that the proposed brake controller has achieved a shorter stopping distance as compared to the conventional brake controller,and the brake control algorithm was able to maintain the operational condition even at the abrupt changes in adhesion condition.展开更多
Helicopter noise features under typical flight condition were investigated based on wavelet transform. The contribution of blade-vortex interaction (BVI) to helicopter noise and low frequency oscillations beat was sho...Helicopter noise features under typical flight condition were investigated based on wavelet transform. The contribution of blade-vortex interaction (BVI) to helicopter noise and low frequency oscillations beat was shown clearly from the detail of wavelet decomposition for helicopter noise signal.展开更多
Threshold voltage (V<sub>TH</sub>) is the most evocative aspect of MOSFET operation. It is the crucial device constraint to model on-off transition characteristics. Precise V<sub>TH</sub> value...Threshold voltage (V<sub>TH</sub>) is the most evocative aspect of MOSFET operation. It is the crucial device constraint to model on-off transition characteristics. Precise V<sub>TH</sub> value of the device is extracted and evaluated by several estimation techniques. However, these assessed values of V<sub>TH</sub> diverge from the exact values due to various short channel effects (SCEs) and non-idealities present in the device. Numerous prevalent V<sub>TH</sub> extraction methods are discussed. All the results are verified by extensive 2-D TCAD simulation and confirmed through analytical results at 10-nm technology node. Aim of this research paper is to explore and present a comparative study of largely applied threshold extraction methods for bulk driven nano-MOSFETs especially at 10-nm technology node along with various sub 45-nm technology nodes. Application of the threshold extraction methods to implement noise analysis is briefly presented to infer the most appropriate extraction method at nanometer technology nodes.展开更多
The underwater counter-rotation propeller non-cavitation noise has an obvious mod- ulation characteristic which is due to the interaction of flow and blade. A modulation mecha- nism is presented in this paper. A sound...The underwater counter-rotation propeller non-cavitation noise has an obvious mod- ulation characteristic which is due to the interaction of flow and blade. A modulation mecha- nism is presented in this paper. A sound pressure spectrum model is presented to describe its non-cavitation noise with application of generalized acoustic analogy method, the modulation mechanism is expressed with the improvement of sound pressure model. The power spectrum and modulation spectrum are presented by numerical simulation. Theoretical analysis and nu- merical simulation results are verified by the cavitation tunnel experiment. The modulation model of counter-rotation propeller is beneficial to the prediction modulation characteristics and identification of underwater high-speed vehicles.展开更多
Local-linear-prediction in phase space is performed for the underwater acoustic target radiated noise. Relation curve of average prediction error versus neighboring points' number is calculated. The result is used...Local-linear-prediction in phase space is performed for the underwater acoustic target radiated noise. Relation curve of average prediction error versus neighboring points' number is calculated. The result is used in judging the nonlinearity of radiated noise time series, and obtaining the appropriate form and coefficients of predicting model. The line and continuous spectral component are predicted respectively. Choice of some model parameters minimizing the prediction error is also discussed.展开更多
文摘Electric vibrators find wide applications in reliability testing, waveform generation, and vibration simulation, making their noise characteristics a topic of significant interest. While Variational Mode Decomposition (VMD) and Empirical Wavelet Transform (EWT) offer valuable support for studying signal components, they also present certain limitations. This article integrates the strengths of both methods and proposes an enhanced approach that integrates VMD into the frequency band division principle of EWT. Initially, the method decomposes the signal using VMD, determining the mode count based on residuals, and subsequently employs EWT decomposition based on this information. This addresses mode aliasing issues in the original method while capitalizing on VMD’s adaptability. Feasibility was confirmed through simulation signals and ultimately applied to noise signals from vibrators. Experimental results demonstrate that the improved method not only resolves EWT frequency band division challenges but also effectively decomposes signal components compared to the VMD method.
基金Project supported jointly by the National Natural Science Foundation of China (No.50608036)the Innovative Funding of the Ministry of Water Resources of China (No. SCX2003-18)
文摘As vibration-based structural damage detection methods are easily affected by environmental noise, a new statistie-based noise analysis method is proposed together with the Monte Carlo technique to investigate the influence of experimental noise of modal data on sensitivity-based damage detection methods. Different from the com- monly used random perturbation technique, the proposed technique is deduced directly by Moore-Pen"ose generalized inverse of the sensitivity matrix, which does not only make the analysis process more efficient but also can analyze the influence of noise on both frequencies and mode shapes for three commonly used sensitivity-based damage detection methods in a similar way. A one-story portal frame is adopted to evaluate the efficiency of the proposed noise analysis technique.
基金supported by the National 863 Projects under Grant No. 2007AA03Z415.
文摘A distributed feedback fiber laser (DFB FL) sensor system with ultra-high resolution is described. The sensor is made by writing distributed feedback structures into a high gain active fiber, and the system employs an unbalanced Michelson interferometer to translate laser wavelength shifts induced by weak measurands into phase shifts. A digital phase generated carrier demodulation scheme is introduced to achieve ultra-high resolution interrogation. A detailed noise analysis of the system is presented, and it is shown that the system resolution is limited by the frequency noise of the DFB FL.
文摘The corrosion behavior of pure copper electrode exposed to artificial seawater has been studied using electrochemical noise analysis (ENA) and electrochemical impedance spectroscopy (EIS). A diffusion process was observed for copper exposed to chloride media as indicated by the presence of a minimum phase angle over the lowest frequency range in the impedance plots. Analysis of electrochemical noise (EN) data has been collected both in time and frequency domains. Noise resistance Rn was obtained after analyzing EN data in the time domain. A good agreement was observed between Rn values and polarization resistance Rp values obtained from EIS analysis. Localization index Ii was not found to provide information concerning corrosion mechanisms. Also skewness and kurtosis for both potential and current fluctuations did not show any mechanistic information. It was concluded that ENA could detect the corrosion rate for copper exposed to chloride media, but was not found to provide information about the corrosion mechanisms.
基金supported by the National High Technology Research and Development Program of China(No.2008AA042201).
文摘A single-loop fourth-order sigma-delta(ΣΔ) interface circuit for a closed-loop micromachined accelerometer is presented.Two additional electronic integrators are cascaded with the micromachined sensing element to form a fourth-order loop filter.The three main noise sources affecting the overall system resolution of aΣΔaccelerometer, mechanical noise,electronic noise and quantization noise,are analyzed in detail.Accurate mathematical formulas for electronic and quantization noise are established.The ASIC is fabricated in a 0.5μm two-metal two-poly n-well CMOS process.The test results indicate that the mechanical noise and electronic noise are 1μg/(Hz)^(1/2) and 8μV/(Hz)^(1/2) respectively,and the theoretical models of electronic and quantization noise agree well with the test and simulation results.
基金This work was funded by the National Basic Research Program of China(973 Program)(No.2014CB046200)the National Nature science Foundation(No.51506089)+1 种基金the Jiangsu Provincial Natural Science Foundation(No.BK20140059)the Priority Academic Program Development of Jiangsu Higher Education Institutions.
文摘With lower turbulence and less rigorous restrictions on noise levels,offshore wind farms provide favourable conditions for the development of high-tip-speed wind turbines.In this study,the multi-objective optimization is presented for a 5MW wind turbine design and the effects of high tip speed on power output,cost and noise are analysed.In order to improve the convergence and efficiency of optimization,a novel type of gradient-based multi-objective evolutionary algorithm is proposed based on uniform decomposition and differential evolution.Optimization examples of the wind turbines indicate that the new algorithm can obtain uniformly distributed optimal solutions and this algorithm outperforms the conventional evolutionary algorithms in convergence and optimization efficiency.For the 5MW wind turbines designed,increasing the tip speed can greatly reduce the cost of energy(COE).When the tip speed increases from 80m/s to 100m/s,under the same annual energy production,the COE decreases by 3.2%in a class I wind farm and by 5.1%in a class III one,respectively,while the sound pressure level increases by a maximum of 4.4dB with the class III wind farm case.
基金Supported by the National Natural Science Foundation of China under Grant Nos 61472048,61402058,61272511,61472046,61202082 and 61370194the Beijing Natural Science Foundation under Grant No 4152038the China Postdoctoral Science Foundation Funded Project under Grant No 2014M561826
文摘To analyze the security of two-step quantum direct communication protocol (QDCP) by using Einstein-Podolsky Rosen pair proposed by Deng et al. [Phys. Rev. A 68 (2003)042317] in collective-rotation noise channel, an excellent model of noise analysis is proposed. In the security analysis, the method of the entropy theory is introduced, and is compared with QDCP, an error rate point Qo(M : (Q0, 1.0)) is given. In different noise levels, if Eve wants to obtain the same amount of information, the error rate Q is distinguishable. The larger the noise level ~ is, the larger the error rate Q is. When the noise level ~ is lower than 11%, the high error rate is 0.153 without eavesdropping. Lastly, the security of the proposed protocol is discussed. It turns out that the quantum channel will be safe when Q 〈 0.153. Similarly, if error rate Q〉 0.153 = Q0, eavesdropping information I 〉 1, which means that there exist eavesdroppers in the quantum channel, and the quantum channel will not be safe anymore.
文摘This study focuses on a single-stage axial flow fan, investigating the effect of three kinds of wave leading edge stator blades on its noise reduction. The DDES method and the duct acoustic analogy theory based on the penetrable data surface were used for noise prediction. The results showed that the three kinds of wave leading edge blades were effective in reducing the rotor-stator interaction tonal noise and also have a certain inhibitory effect on broadband noise. The A10W15 stator blade can effectively reduce broadband noise in the frequency range of 2200 - 4200 Hz. When the amplitude is increased to 20, the noise reduction effect is further enhanced. However, when the amplitude is increased to 30, the broadband noise reduction effect is no longer significant. Further research shows that the wave leading edge stator blades can significantly change the pressure fluctuation distribution on the leading edge and suction surface, which control the modal energy distribution. Finally, this paper analyzed multiple factors affecting the broadband noise reduction, such as the noise source cut-off and cut-on effect and correlation. The purpose of this paper is to explore the laws of the influence of wave leading edge blades on the duct noise of real fan, and to reveal its noise control mechanism. .
基金This research was supported by National Key R&D Program of China:Gravitational Wave Detection Project(Nos.2021YFC2202601,2021YFC2202603)National Natural Science Foundation of China(No.12172288).
文摘This paper presents Part II of a review on DFACS,which specifically focuses on the modeling and analysis of disturbances and noises in DFACSs.In Part I,the system composition and dynamics model of the DFACS were presented.In this paper,we discuss the effects of disturbance forces and noises on the system,and summarize various analysis and modeling methods for these interferences,including the integral method,frequency domain analysis method,and magnitude evaluation method.By analyzing the impact of disturbances and noises on the system,the paper also summarizes the system’s performance under slight interferences.Additionally,we highlight current research difficulties in the field of DFACS noise analysis.Overall,this paper provides valuable insights into the modeling and analysis of disturbances and noises in DFACSs,and identifies key areas for future research.
基金supported by NSFC (10401011,10871153)China Postdoctoral Science Foundation (2005037660)
文摘Under the framework of white noise analysis, the existence of scattering solutions to the abstract dynamical φ4^4 wave equations in terms of generalized operators (see Section 3 below) is proven via a combination of the characterization for the symbol of generalized operators and the classical scattering results. In addition, some properties (Poincare invariance and irreducibility) of the solutions are discussed.
文摘The relation between generalized operators and operator-valued distributions is discussed so that these two viewpoints can be used alternatively to explain quantum fields.
文摘The velocities of tectonic plates derived from GNSS time series are regularly used as input data for geophysical models. However, as shown by numerous researches, the coordinates time series contain residual errors of a systematic nature, which can significantly affect the reliability of the obtained velocity estimates. This research shows that using non-classical error theory of measurement(NETM)for processing GNSS time series allows detecting the presence of weak, not removed from GNSS processing, sources of systematic errors. Based on the coordinate time series of selected permanent GNSS stations in Europe, we checked the empirical distributions of errors by the NETM on G. Jeffries’ recommendations and on the principles of the theory of hypothesis tests according to Pearson’s criterion. It is established that the obtained coordinates time series of GNSS-stations only partially confirm the hypothesis of their conformity to the normal Gaussian distribution law, and this may be the main reason for their unrepresentative classification. In the future, it is necessary to identify and take into account the causes of residual errors that distort the real distribution of the results of the GNSS time series.
基金supported by the State Key Development Program for Basic Research of China (Grant No.2010CB328300)the National Natural Science Foundation of China (Grant Nos.60677004 and 60702049)+1 种基金the Program for the New Century Excellent Talents in University of China (Grant No.NECT-07-0111)the Innovation Plan for Youth of Beijing University of Posts and Telecommunications
文摘Optical buffers are critical for optical signal processing in future optical packet-switched networks. In this paper, a theoretical study as well as an experimental demonstration on a new optical buffer with large dynamical delay time is carried out based on cascaded double loop optical buffers (I:)LOBs). It is found that pulse distortion can be restrained by a negative optical control mode when the optical packet is in the loop. Noise analysis indicates that it is feasible to realise a large variable delay range by cascaded DLOBs. These conclusions are validated by the experiment system with 4-stage cascaded DLOBs. Both the theoretical simulations and the experimental results indicate that a large delay range of 1-9999 times the basic delay unit and a fine granularity of 25 ns can be achieved by the cascaded DLOBs. The performance of the cascaded DLOBs is suitable for the all optical networks.
文摘An optimized structure to weaken the vibration and noise of a new asymmetric permanent magnet-assisted synchronous reluctance motor(PMaSynRM)is proposed.The new asymmetric PMaSynRM has the advantages of a low torque ripple and high fault tolerance.However,the asymmetric structure generates an unbalanced magnetic force(UMF),which results in vibration and noise problems.In this study,the vibration and noise of the motor are analyzed and optimized.First,the radial pressure is analyzed,and an optimized structure is proposed.The electromagnetic performance of the motor before and after optimization is analyzed using the finite element method.Second,a three-dimensional model is established,and modal analysis is conducted considering the orthotropy of the stator and effective windings.Finally,the vibration and noise are simulated and analyzed,and the validity of the analysis results is verified experimentally.The analysis results indicate that the optimized motor realizes a reduction in the motor vibration and noise.
基金The authors greatly appreciate the financial support from the Rail Manufacturing Cooperative Research Centre(funded jointly by participating rail organisations and the Australian Federal Government’s Business Cooperative Research Centres Programme)through Project R1.7.1–“Estimation of adhesion conditions between wheels and rails for the development of advanced braking control systems”.
文摘The dynamic parameters of a roller rig vary as the adhesion level changes.The change in dynamics parameters needs to be analysed to estimate the adhesion level.One of these parameters is noise emanating from wheel–rail interaction.Most previous wheel–rail noise analysis has been conducted to mitigate those noises.However,in this paper,the noise is analysed to estimate the adhesion condition at the wheel–rail contact interface in combination with the other methodologies applied for this purpose.The adhesion level changes with changes in operational and environmental factors.To accurately estimate the adhesion level,the influence of those factors is included in this study.The testing and verification of the methodology required an accurate test prototype of the roller rig.In general,such testing and verification involve complex experimental works required by the intricate nature of the adhesion process and the integration of the different subsystems(i.e.controller,traction,braking).To this end,a new reduced-scale roller rig is developed to study the adhesion between wheel and rail roller contact.The various stages involved in the development of such a complex mechatronics system are described in this paper.Furthermore,the proposed brake control system was validated using the test rig under various adhesion conditions.The results indicate that the proposed brake controller has achieved a shorter stopping distance as compared to the conventional brake controller,and the brake control algorithm was able to maintain the operational condition even at the abrupt changes in adhesion condition.
文摘Helicopter noise features under typical flight condition were investigated based on wavelet transform. The contribution of blade-vortex interaction (BVI) to helicopter noise and low frequency oscillations beat was shown clearly from the detail of wavelet decomposition for helicopter noise signal.
文摘Threshold voltage (V<sub>TH</sub>) is the most evocative aspect of MOSFET operation. It is the crucial device constraint to model on-off transition characteristics. Precise V<sub>TH</sub> value of the device is extracted and evaluated by several estimation techniques. However, these assessed values of V<sub>TH</sub> diverge from the exact values due to various short channel effects (SCEs) and non-idealities present in the device. Numerous prevalent V<sub>TH</sub> extraction methods are discussed. All the results are verified by extensive 2-D TCAD simulation and confirmed through analytical results at 10-nm technology node. Aim of this research paper is to explore and present a comparative study of largely applied threshold extraction methods for bulk driven nano-MOSFETs especially at 10-nm technology node along with various sub 45-nm technology nodes. Application of the threshold extraction methods to implement noise analysis is briefly presented to infer the most appropriate extraction method at nanometer technology nodes.
基金supported by the National Natural Science Foundation of China(11704345)the Key Laboratory of Science and Technology for National Defence Foundation(9140C290304140C29133)
文摘The underwater counter-rotation propeller non-cavitation noise has an obvious mod- ulation characteristic which is due to the interaction of flow and blade. A modulation mecha- nism is presented in this paper. A sound pressure spectrum model is presented to describe its non-cavitation noise with application of generalized acoustic analogy method, the modulation mechanism is expressed with the improvement of sound pressure model. The power spectrum and modulation spectrum are presented by numerical simulation. Theoretical analysis and nu- merical simulation results are verified by the cavitation tunnel experiment. The modulation model of counter-rotation propeller is beneficial to the prediction modulation characteristics and identification of underwater high-speed vehicles.
基金The work was supported by the fund (2000JS24.4.1) from the State Key Lab on Ocean Acoustics andthe research fund of Ship Industry Fundamental Research.
文摘Local-linear-prediction in phase space is performed for the underwater acoustic target radiated noise. Relation curve of average prediction error versus neighboring points' number is calculated. The result is used in judging the nonlinearity of radiated noise time series, and obtaining the appropriate form and coefficients of predicting model. The line and continuous spectral component are predicted respectively. Choice of some model parameters minimizing the prediction error is also discussed.