The Effect of Lateral Guiding Mechanism on Noise Characteristics in Semiconductor Lasers

A comparison between intensity noise spectra and also the line shapes of gain-guided, weakly-index-guided, and strongly-index-guided semiconductor lasers are made using numerical solution of Maxwell-Bloch equations including spontaneous emission noise.

Observation of nonconservation characteristics of radio frequency noise mechanism of 40-nm n-MOSFET

Bias non-conservation characteristics of radio-frequency noise mechanism of 40-nm n-MOSFET are observed by modeling and measuring its drain current noise. A compact model for the drain current noise of 40-nm MOSFET is proposed through the noise analysis. This model fully describes three kinds of main physical sources that determine the noise mechanism of 40-nm MOSFET, i.e., intrinsic drain current noise, thermal noise induced by the gate parasitic resistance, and coupling thermal noise induced by substrate parasitic effect. The accuracy of the proposed model is verified by noise measurements, and the intrinsic drain current noise is proved to be the suppressed shot noise, and with the decrease of the gate voltage, the suppressed degree gradually decreases until it vanishes. The most important findings of the bias non-conservative nature of noise mechanism of 40-nm n-MOSFET are as follows.（i） In the strong inversion region, the suppressed shot noise is weakly affected by the thermal noise of gate parasitic resistance. Therefore, one can empirically model the channel excess noise as being like the suppressed shot noise.（ii） In the middle inversion region, it is almost full of shot noise.（iii） In the weak inversion region, the thermal noise is strongly frequency-dependent, which is almost controlled by the capacitive coupling of substrate parasitic resistance. Measurement results over a wide temperature range demonstrate that the thermal noise of 40-nm n-MOSFET exists in a region from the weak to strong inversion, contrary to the predictions of suppressed shot noise model only suitable for the strong inversion and middle inversion region. These new findings of the noise mechanism of 40-nm n-MOSFET are very beneficial for its applications in ultra low-voltage and low-power RF, such as novel device electronic structure optimization, integrated circuit design and process technology evaluation.

Temperature-Dependent Drain Current Characteristics and Low Frequency Noises in Indium Zinc Oxide Thin Fihn Transistors

The I-V characteristics and low frequency noises for indium zinc oxide thin film transistor are measured between 250 K and 430 K. The experimental results show that drain currents are thermally activated following the Meyer Neldel rule, which can be explained by the multiple-trapping process. Moreover, the field effect electron mobility firstly increases, and then decreases with the increase of temperature, while the threshold voltage decreases with increasing the temperature. The activation energy and the density of localized gap states are extracted. A noticeable increase in the density of localized states is observed at the higher temperatures.

Design and Analysis of the Gemini Chain System in Dual Clutch Transmission of Automobile

Chain drive system is widely used in the conditions of high-speed, overload, variable speed and load, Many studies are focused on the meshing theory and wear characteristics of chain drive system, but system design, analysis, and noise characteristics of the chain drive system are weak. System design and noise characteristic are studied for a new type Gemini chain of dual-clutch automatic transmission. Based on the meshing theory of silent chain, the design parameters of the Gemini chain system are calculated and the mathematical models and dynamic analysis models of the Gemini chain system are established. Dynamic characteristics of the Gemini chain system is simulated and the contact force of plate and pin, plate and sprockets, the chain tension forces, the transmission error and the stress of plates and pins are analyzed. According to the simulation results of the Gemini chain system, the noise experiment about system is carried out. The noise values are tested at different speed and load and spectral characteristics are analyzed. The results of simulation and experimental show that the contact forces of plate and pin, plate and sprockets are smaller than the allowable stress values, the chain tension force is less than ultimate tension and transmission error is limited in 1.2%. The noise values can meet the requirements of industrial design, and it is proved that the design and analysis method of the Gemini chain system is scientific and feasible. The design and test system is built from analysis to test of Gemini chain system. This research presented will provide a corresponding theoretical guidance for the design and dynamic characteristics and noise characteristics of chain drive system.

Radiation characteristics of intermittence exhaust noise

Aerodynamic characteristics, the noise characteristics in the course of intermittence exhaust are investigated and the expressions for sound pressure level of the noise generated by single-pole source and quadrupole source in the intermittence exhaust noise are established. The effects of all parameters in pneumatic system on the noise are also comprehensively studied.

Study of the effects on GPS coordinate time series caused by higher-order ionospheric corrections calculated using the DIPOLE model

As one of the main error sources in high-precision Global Positioning System （GPS） data processing, higher-order ionospheric （HOI） delays cause significant effects on coordinate time series that cannot be ignored in analyses of long time series. Typically two geomagnetic models, DIPOLE model and Inter- national Geomagnetic Reference Field （IGRF） model, are used for calculating HOI corrections. This paper investigates the effects of HOI correction caused by the DIPOLE model on coordinate time series. GPS data from 104 globally distributed International GNSS Service （IGS） stations spanning from January, 1999 to December, 2003 were reprocessed following up-to-date processing strategies utilizing GAMIT and GLOBK software. Two coordinate time series solutions before and after applying HOI corrections using the DIPOLE model were derived for studying the effects in terms of seasonal variations and noise amplitudes. The results show that after applying the HOI corrections calculated with DIPOLE, the noise amplitudes of the coordinate time series increased, especially in the north and east directions, and the increased amplitudes of the flicker noise were larger than those of the white noise. Furthermore, spurious periodic signals that were probably introduced by the HOI corrections from the DIPOLE model were also found. Moreover, an apparent increase was confirmed for the power spectra of most of the stations, especially in the north direction, and the amplitudes of both the annual and semi-annual signals also increased in the north and east directions. It can be inferred that the quality of the external data sources such as the geomagnetic model might be the key factors that lead to the above results. The results also suggest that we should be very careful when the DIPOLE model is used for HOI corrections.

Actual Sensing Sensitivity and SNR Measurement of Optical Tweezers Based on Coulomb Force Input

Sensing sensitivity is the key performance of optical tweezers.By adjusting the frequency and magnitude of an applied Coulomb force as an input of optical tweezers,we directly measured the sensitivity and signal-to-noise ratio(SNR)of a system and indirectly calculated the actual noise magnitude.Combined with an output filter,the relationship between the SNR and bandwidths was studied.We established the simulation model of a system using Simulink and simulated the relationship between the SNR and magnitude of the input forces and filter bandwidths.In addition,we built an experimental system to determine the relationship between the SNR and the magnitude of the input forces and filter bandwidths.The actual minimum detectable force was measured as 1.8275×10^(-17)N at a 1Hz bandwidth.The experimental results were correlated with the simulation and theoretical results,confirming the effectiveness of the proposed method and demonstrating the high sensitivity of vacuum optical tweezers as mechanical sensors.We proposed a novel method of calibration and measurement of system sensing parameters by applying an actual force that was more direct and precise than the theoretical calculation method that requires accurate fitting parameters,such as the particle radius and density.This method can be employed to analyze the system noise and phase characteristics to confirm and improve the real performance of the system.