期刊文献+
共找到1,087篇文章
< 1 2 55 >
每页显示 20 50 100
Effect of continuous casting speed on mold surface flow and the related near-surface distribution of non-metallic inclusions 被引量:9
1
作者 Peng Fei Yi Min +1 位作者 Cheng-jun Liu Mao-fa Jiang 《International Journal of Minerals,Metallurgy and Materials》 SCIE EI CAS CSCD 2019年第2期186-193,共8页
For the control of surface defects in interstitial-free(IF) steel, quantitative metallographic analyses of near-surface inclusions and surface liquid flow detection via the nail-board tipping method were conducted. Th... For the control of surface defects in interstitial-free(IF) steel, quantitative metallographic analyses of near-surface inclusions and surface liquid flow detection via the nail-board tipping method were conducted. The results show that, at casting speeds of 0.8 and 1.0 m/min, a thin liquid mold flux layer forms and non-uniform floating of argon bubbles occurs, inducing the entrainment and subsequent entrapment of the liquid flux; fine inclusion particles of Al_2O_3 can also aggregate at the solidification front. At higher casting speeds of 1.4 and 1.6 m/min, the liquid mold flux can be entrained and carried deeper into the liquid steel pool because of strong level fluctuations of the liquid steel and the flux. The optimal casting speed is approximately 1.2 m/min, with the most favorable surface flow status and, correspondingly, the lowest number of inclusions near the slab surface. 展开更多
关键词 non-metallic inclusionS DISTRIBUTION CASTING SPEED surface flow
下载PDF
Study on the separation process of non-metallic inclusions at the steel-slag interface using water modeling 被引量:5
2
作者 Ye-lian Zhou Zhi-yin Deng Miao-yong Zhu 《International Journal of Minerals,Metallurgy and Materials》 SCIE EI CAS CSCD 2017年第6期627-637,共11页
The separation process of non-metallic inclusions at the steel–slag interface was simulated by physical modeling. Three different kinds of particles (octahedral, plate-like, and spherical) and three different oils (k... The separation process of non-metallic inclusions at the steel–slag interface was simulated by physical modeling. Three different kinds of particles (octahedral, plate-like, and spherical) and three different oils (kerosene, bean oil, and pump oil) were used to model inclusions and slags, respectively. The effects of inclusion geometry (shape and size) and slag properties (viscosity and interfacial tension) on the separation process were investigated. The results revealed that the variation of surface free energy and the viscosity of the slag are two significant factors affecting the separation process of inclusions at the steel–slag interface. The variation of surface free energy helped inclusions enter the slag phase, whereas the decrease of slag viscosity shortened the separation time. The deformation of the steel–slag interface could give rise to the resistance force, which would resist inclusions passing through the interface. A liquid film formed on the inclusion as it passed through the steel–slag interface, which might be related to the inclusion’s shape. © 2017, University of Science and Technology Beijing and Springer-Verlag Berlin Heidelberg. 展开更多
关键词 Free energy Interfaces (materials) KEROSENE Liquid films SEPARATION VISCOSITY
下载PDF
Study on non-metallic inclusions in Al killed high strength alloy steel refined by high basicity and high Al_2O_3 content slag 被引量:11
3
作者 WANG Xinhua,JIANG Min and WANG Wanjun School of Metallurgical and Ecological Engineering,University of Science and Technology Beijing,Beijing 100083,China 《Baosteel Technical Research》 CAS 2010年第S1期21-,共1页
Laboratory and industrial studies were carried out to investigate non-metallic inclusions in high strength alloy steel refined by high basicity and high Al_2O_3 slag.It was found that the steel/slag reaction time larg... Laboratory and industrial studies were carried out to investigate non-metallic inclusions in high strength alloy steel refined by high basicity and high Al_2O_3 slag.It was found that the steel/slag reaction time largely affected non-metallic inclusions.With the reaction time increased from 30 min to 90 min in laboratory study,MgO-Al_2O_3 spinels were gradually changed into CaO-MgO-Al_2O_3 system inclusions surrounded by softer CaO-Al_2O_3 surface layers.By using high basicity slag which contained as much as 41%Al_2O_3 in the laboratory study,ratio of low melting temperature CaO-MgO-Al_2O_3 system inclusions was remarkably increased to above 80%.In the industrial experiment,during the secondary refining,the inclusions changed in order of 'Al_2O_3→MgO-Al_2O_3→CaO-MgO-Al_2O_3'.Through the LF and RH refining,most inclusions could be transferred to lower melting temperature CaO-Al_2O_3 and CaO-MgO-Al_2O_3 system inclusions. 展开更多
关键词 non-metallic inclusion SPINEL SLAG high strength alloying steel refining fatigue
下载PDF
Effects of calcium treatment on non-metallic inclusions and magnetic properties of non-oriented silicon steel sheets 被引量:7
4
作者 ZHANG Feng MIAO Lede +3 位作者 ZONG Zhenyu WANG Bo ZHANG Yi MA Zhigang 《Baosteel Technical Research》 CAS 2013年第1期12-19,共8页
Based on the industrial production of non-oriented silicon steel,calcium treatment by CaSi wire feeding during the RH refining process was studied. The thermodynamics of CaS inclusion formation was analyzed, and the m... Based on the industrial production of non-oriented silicon steel,calcium treatment by CaSi wire feeding during the RH refining process was studied. The thermodynamics of CaS inclusion formation was analyzed, and the morphology and the size distribution were observed. Furthermore, the change in inclusion characteristics after calcium treatment and the effect of calcium treatment on magnetic properties were discussed. The results show that the formation of MnS and A1N inclusions were restrained, and the aggregating, floating and removing of microinclusions after calcium treatment were effectively promoted. The cleanliness of liquid steel was obviously increased. The main type of inclusions was single phase of CaO, with some complex inclusions composed of CaO, SiO2 and MgO. No CaS inclusion was observed after an appropriate calcium treatment. The size of all inclusions was distributed in the range of 2 - 20 μm, and the number was about 1.8 × 10^5/mm3. In addition, as an increasing amount of calcium was added,the core loss gradually decreased to a stable level, and the magnetic induction decreased quickly after a slow increase. The optimal calcium treatment mode depends on the chemical composition of steel. 展开更多
关键词 non-oriented silicon steel RH refining calcium treatment inclusion magnetic property
下载PDF
Three-dimensional analysis technology for accurately characterizing non-metallic inclusion particles in steel 被引量:1
5
作者 ZHANG Yi CHEN Jinming +2 位作者 MIAO Lede WANG Guodong WU Junfei 《Baosteel Technical Research》 CAS 2011年第4期40-48,共9页
In this paper, a kind of three-dimensional analysis technology for characterizing non-metallic inclusions in steel was clearly elaborated. It is an electron microscopy observation, namely the non-aqueous electrolysis ... In this paper, a kind of three-dimensional analysis technology for characterizing non-metallic inclusions in steel was clearly elaborated. It is an electron microscopy observation, namely the non-aqueous electrolysis extraction method with a settled coulometer. In the research,the extraction effects of non-metallic inclusions in different electrolysis systems were studied, and it was concluded that alkalescent 2% TEA non-aqueous electrolyte was applicable for extracting most of non-metallic inclusion particles in steel. And then, in order to ensure the microscopic characterization and statistical calculation of inclusion particles, some electrolysis parameters should be confirmed, such as the size of the sample, control of the electrolysis mass, electric current, etc. Furthermore, for preventing the disturbance of carbides and presenting clear three-dimensional appearance by microscopic characterization, magnetic separation was utilized to separate the inclusion particles from carbides, which was useful for getting more veracious types, particle sizes and chemical composition of inclusions. Moreover, through calculation of quantity and particle size of inclusions in continuous determinate fields, the total quantity per unit volume or area and the particle size distribution of inclusions could be acquired by conversion with electrolysis loss. Besides, the comparison between this method and traditional quantitative metallography was also discussed, and finally, a conclusion was drawn that both of them have respectively applications in characterizing inclusions. 展开更多
关键词 non-metallic inclusion non-aqueous electrolytic extraction SEM microscopic characterization
下载PDF
Behavior of Non-metallic Inclusions in Centrifugal Induction Electroslag Castings 被引量:1
6
作者 Xichun Chen, Jie Fu, Deguang Zhou, Weiguo Xu (Metallurgy School, University of Science and Technology Beijing, Beijing 100083, China) 《Journal of University of Science and Technology Beijing》 CSCD 2001年第2期91-94,共4页
In order to know the behavior of non-metallic inclusions in centrifugal induction electroslag castings (CIESC), non-metallic inclusions in 5CrMnMo and 4Cr5MoSiV1 were qualitatively and quantitatively analyzed. The lar... In order to know the behavior of non-metallic inclusions in centrifugal induction electroslag castings (CIESC), non-metallic inclusions in 5CrMnMo and 4Cr5MoSiV1 were qualitatively and quantitatively analyzed. The largest size of inclusions in the casting and the thermodynamic possibility of TiN precipitation in steel were also calculated. The results show that sulfide inclusions are evenly distributed and the content is low. The amount of oxide inclusions in CIESC: 4Cr5MoSiV1 steel is close to the ESR steel and lower than that in the EAF steel, and there are some differences along radial direction. Nitride inclusions are fine and the diameter of the largest one is 3-1 mum. With the increase of the centrifugal machine's rotational speed, the ratio of round inclusions increases and the ratio of sharp inclusions decreases. According to the experiment and the calculation results, it is pointed out that the largest diameter of non-metallic inclusions in the CIESC 4Cr5MoSiV1 casting is only 6.6 mum, and [N%][Ti%] in 4Cr5MoSiV1 steel should be controlled less than 4.4x 10(-5) in order to further reduce the amount and size of TiN inclusions. 展开更多
关键词 centrifugal induction electroslag casting non-metallic inclusions 4Cr5MoSiV1 steel 5CrMnMo steel TiN precipitation
下载PDF
Characterization and analysis of non-metallic inclusions in Ni42-Fe expansive alloy
7
作者 沈婕 夏天东 +1 位作者 王晓军 冯晓春 《中国有色金属学会会刊:英文版》 CSCD 2007年第A02期1165-1171,共7页
Cracks and ruptures always occur during wire drawing process of 42% nickel-iron expansive alloy. In order to study the reasons of these phenomena,a method of metallographic observation in combination with sample elect... Cracks and ruptures always occur during wire drawing process of 42% nickel-iron expansive alloy. In order to study the reasons of these phenomena,a method of metallographic observation in combination with sample electrolysis was used to characterize the non-metallic inclusions in the alloy wire. The results indicate that the inclusions in the alloy are oxidation products during the process of melting. There are single or complex phase inclusions composed of elements such as Al,Si,Ca,Ti,Fe,and O2. Among them,the macro-inclusions are TiO2 compound inclusions formed by the adhesion of Al and Si oxides on them. These inclusions are fragile ones with a low strain rate,as well as a rather high hardness,so that they are the main reason that leads to the surface cracks and ruptures in the alloy wires. The analysis has educed that the key point to enhance the product quality is to promote the cleanliness of the melt,control the types and quantity of non-metal inclusions in the alloy. 展开更多
关键词 镍-铁膨胀合金 非金属夹杂物 机械特征 裂纹
下载PDF
Non-metallic Inclusions in Continuously Cast Aluminum Killed Steels
8
作者 Wenjun Wang, Xinhua Wang, Jiongming Zhang, Wanjun Wang, Youyu Zhou ( Metallurgy School, University of Science and Technology Beijing, Beijing 100083, China Steelmaking Research Institute, Wuhan Iron and Steel Group, Wuhan 430080, China) 《International Journal of Minerals,Metallurgy and Materials》 SCIE EI CAS CSCD 2000年第3期193-196,共4页
In aluminum killed steels, the size, shape, quantity and formation of non-metallic inclusions in ladle steel (before and after RH vacuum treatment) and in tundish as well as in slabs were studied by EPMA (Electron Pro... In aluminum killed steels, the size, shape, quantity and formation of non-metallic inclusions in ladle steel (before and after RH vacuum treatment) and in tundish as well as in slabs were studied by EPMA (Electron Probe Microanalysis) and by analyzing the total oxygen. The results showed that in the slabs the total oxygen was quite low and the inclusions discovered were mainly small-sized angular alumina inclusions. This indicates that most inclusions have been removed by floating out during the continuous casting process. In addition, the countermeasures were discussed to decrease the alumina inclusions in the slabs further. 展开更多
关键词 aluminum killed steel non-metallic inclusion ALUMINA continuous casting
下载PDF
Effect of inclusions on the formation of acicular ferrite in Ti-bearing non quenched-and-tempered steel 被引量:6
9
作者 Ying Yang Chaobin Lai +2 位作者 Fuming Wang Zhanbing Yang Bo Song 《Journal of University of Science and Technology Beijing》 CSCD 2007年第6期501-506,共6页
Nucleation of acicular ferrite and its influence factors in non quenched-and-tempered steel was studied by using TEM and thermodynamic calculation. The results show that the complex particles with a center made of Ti ... Nucleation of acicular ferrite and its influence factors in non quenched-and-tempered steel was studied by using TEM and thermodynamic calculation. The results show that the complex particles with a center made of Ti oxide, Al2O3, and silicate and an outside made of a small quantity of mixture of TiN and MnS are able to act as ferrite nucleation nuclei. The acicular ferrite percentage changes little with Ti. When the oxygen content was 80 ppm, the volume percentage of acicular ferrite decreased due to an increase in allotriomorphic ferrite. The larger the cooling rate and the shorter the incubation time, the finer the titanium oxide and the higher the nucleation ratio of acicular ferrite. 展开更多
关键词 acicular ferrite titanium inclusionS non quenched-and-tempered steel
下载PDF
Control of nonmetallic inclusions of non-oriented silicon steel sheets by the rare earth treatment 被引量:13
10
作者 ZHANG Feng MA Changsong +3 位作者 WANG BO ZHANG Peili MA Zhigang ZHANG Yi 《Baosteel Technical Research》 CAS 2011年第2期41-45,共5页
Based on the industrial production of non-oriented silicon steel, the rare earth (RE) treatment during the Ruhrstahl Heraeus (RH) refining process was studied. The morphology and the size distribution were observe... Based on the industrial production of non-oriented silicon steel, the rare earth (RE) treatment during the Ruhrstahl Heraeus (RH) refining process was studied. The morphology and the size distribution were observed for the steel specimens treated with different RE treatment conditions. Furthermore, the formation and change of the nonmetallic inclusion characteristics of finished steel sheets after the RE treatment were discussed. The results have shown that in the present work,the suitable RE metal additions are 0.6 -0.9 kg/t steel. After the suitable RE treatment,the formation of AIN and MnS inclusions were restrained, and the aggregation, flotation and removal of nonmetallic inclusions were efficiently promoted and the cleanliness of liquid steel was significantly increased. Meanwhile, the total oxygen concentration reached the minimum value and thle desulfurization efficiency was optimal ,and the type of main inclusions was approximately spherical or elliptical spherical RE radicle inclusions whose size was relatively large. 展开更多
关键词 non-oriented silicon steel Ruhrstahl Heraeus (RIt) refining rare earth (RE) treatment nonmetallic inclusions
下载PDF
Effect of retained austenite and nonmetallic inclusions on the thermal/electrical properties and resistance spot welding nuggets of Si-containing TRIP steels 被引量:1
11
作者 V.H.Vargas I.Mejía +1 位作者 V.H.Baltazar-Hernández C.Maldonado 《International Journal of Minerals,Metallurgy and Materials》 SCIE EI CAS CSCD 2019年第1期52-63,共12页
Five advanced high-strength transformation-induced plasticity(TRIP) steels with different chemical compositions were studied to correlate the retained austenite and nonmetallic inclusion content with their physical pr... Five advanced high-strength transformation-induced plasticity(TRIP) steels with different chemical compositions were studied to correlate the retained austenite and nonmetallic inclusion content with their physical properties and the characteristics of the resistance spot welding nuggets. Electrical and thermal properties and equilibrium phases of TRIP steels were predicted using the JMatPro? software. Retained austenite and nonmetallic inclusions were quantified by X-ray diffraction and saturation magnetization techniques. The nonmetallic inclusions were characterized by scanning electron microscopy. The results show that the contents of Si, C, Al, and Mn in TRIP steels increase both the retained austenite and the nonmetallic inclusion contents. We found that nonmetallic inclusions affect the thermal and electrical properties of the TRIP steels and that the differences between these properties tend to result in different cooling rates during the welding process. The results are discussed in terms of the electrical and thermal properties determined from the chemical composition and their impact on the resistance spot welding nuggets. 展开更多
关键词 transformation-induced plasticity steel RETAINED austenite non-metallic inclusions magnetic saturation electrical PROPERTIES THERMAL PROPERTIES resistance spot welding NUGGET
下载PDF
Determination of elastic moduli of composite medium containing bimaterial matrix and non-uniform inclusion concentrations
12
作者 Weitao SUN 《Applied Mathematics and Mechanics(English Edition)》 SCIE EI CSCD 2017年第1期15-28,共14页
Reservoir porous rocks usually consist of more than two types of matrix materials, forming a randomly heterogeneous material. The determination of the bulk modulus of such a medium is critical to the elastic wave disp... Reservoir porous rocks usually consist of more than two types of matrix materials, forming a randomly heterogeneous material. The determination of the bulk modulus of such a medium is critical to the elastic wave dispersion and attenuation. The elastic moduli for a simple matrix-inclusion model are theoretically analyzed. Most of the efforts assume a uniform inclusion concentration throughout the whole single-material matrix. However, the assumption is too strict in real-world rocks. A model is developed to estimate the moduli of a heterogeneous bimaterial skeleton, i.e., the host matrix and the patchy matrix. The elastic moduli, density, and permeability of the patchy matrix differ from those of the surrounding host matrix material. Both the matrices contain dispersed particle inclusions with different concentrations. By setting the elastic constant and density of the particles to be zero, a double-porosity medium is obtained. The bulk moduli for the whole system are derived with a multi-level effective modulus method based on Hashin's work. The proposed model improves the elastic modulus calculation of reservoir rocks, and is used to predict the kerogen content based on the wave velocity measured in laboratory. The results show pretty good consistency between the inversed total organic carbon and the measured total organic carbon for two sets of rock samples. 展开更多
关键词 heterogeneous porous matrix composite material non-uniform inclusion concentration bulk modulus total organic carbon inversion
下载PDF
Thermodynamic aspects of inclusion engineering in steels 被引量:5
13
作者 A.Costa e Silva 《Rare Metals》 SCIE EI CAS CSCD 2006年第5期412-419,共8页
Tailoring non-metallic inclusions in accordance to the desired effect on steel properties has gained widespread acceptance in the last decades and has become known as “inclusion engineering”. Effective inclusion eng... Tailoring non-metallic inclusions in accordance to the desired effect on steel properties has gained widespread acceptance in the last decades and has become known as “inclusion engineering”. Effective inclusion engineering involves three steps: (a) a good knowledge of how inclusions influence properties, (b) understanding what is the effect of each type of inclusions on these properties and thus which is the most desirable inclusion in a given product and (c) adjusting the processing parameters to obtain these inclusions. A significant portion of the process adjustment is done during steel refining, where the steel can be tailored so that the desired chemical composition of the non-metallic inclusions that will precipi- tate can be altered. Understanding the relations between steel chemistry, processing variables and inclusion chemical composition requires significant understanding of the thermodynamics of the systems involved. These complex equilibrium calculations are best done using computational thermodynamics. In this work some of the basic techniques used to control inclusion composition are reviewed and the thermodynamic information required to perform this task is presented. Several examples of the application of computational thermodynamics to inclusion engineering of different steels grades are presented and compared with experimental results, whenever possible. The potential and limitations of the method are highlighted, in special those related to thermodynamic data and databases. 展开更多
关键词 computational thermodynamics STEEL non-metallic inclusions
下载PDF
Modeling study on fluid flow and inclusion motion in 6-strand bloom caster tundishes 被引量:3
14
作者 GuanghuaWen LifengZhang +4 位作者 PingTang ZhenjiangSu MingmeiZhu WuanGut andKewenZhao: 《Journal of University of Science and Technology Beijing》 CSCD 2004年第4期310-314,共5页
The behavior of fluid flow and particle motion in a 6-strand bloom castertundish was investigated by a water model and numerical simulation. Compared with a device withoutflow control, the tundish with flow control ha... The behavior of fluid flow and particle motion in a 6-strand bloom castertundish was investigated by a water model and numerical simulation. Compared with a device withoutflow control, the tundish with flow control has an important effect on the fluid flow pattern andinclusion removal. It is revealed that by non-isothermal process, which is real productioncondition, the fluid flow in tundish shows a strong buoyancy pattern, which drives particles to moveupwards. The particle removal was quantitatively studied by mathematical and physical simulations. 展开更多
关键词 physical and mathematical simulation non-isothermal process fluid flow inclusion removal multi-strand tundish
下载PDF
ULTRASONIC SEPARATION OF MICRO-SIZED INCLUSIONS IN MOLTEN METAL
15
作者 X.Q. Bai and J.C. He Key Laboratory of National Education Ministry for Electromagnetic Processing of Materials, Northeastern University, Shenyang 110004, China 《Acta Metallurgica Sinica(English Letters)》 SCIE EI CAS CSCD 2001年第5期375-379,共5页
The coagulation time and position of micro-sized non-metallic inclusions in molten metal during ultrasonic separation process were investigated, and the motion course of micro-sized non-metallic inclusions in an ultra... The coagulation time and position of micro-sized non-metallic inclusions in molten metal during ultrasonic separation process were investigated, and the motion course of micro-sized non-metallic inclusions in an ultrasonic standing wave field was numerically simulated. The results of theoretical analysis and numerical simulation show that the movement of inclusions depends on the balance between the acoustic radiation force, effective buoyancy force and viscous drag force. It is presented that micro-sized inclusions, agglomerated at antinode-planes may be removed further with horizon tal ultrasound.`` 展开更多
关键词 ULTRASOUND molten metal micro-sized non-metallic inclusion numerical simulation process parameter
下载PDF
数字普惠金融、农民增收与共同富裕
16
作者 姚凤阁 于佳怡 石周昊 《农业经济与管理》 CSSCI 北大核心 2024年第3期93-109,共17页
数字普惠金融能够缓解农村金融困境,成为巩固脱贫攻坚成果、实现共同富裕的重要方式。基于2013—2022年中国280个地市级面板数据,实证检验了数字普惠金融对共同富裕的影响机制、非线性关系及空间溢出效应。研究表明,我国区域间共同富裕... 数字普惠金融能够缓解农村金融困境,成为巩固脱贫攻坚成果、实现共同富裕的重要方式。基于2013—2022年中国280个地市级面板数据,实证检验了数字普惠金融对共同富裕的影响机制、非线性关系及空间溢出效应。研究表明,我国区域间共同富裕水平呈显著的空间正相关性,且样本考察期内集聚模式未发生显著变化,具有显著的空间集聚性;机制分析表明,数字普惠金融对共同富裕具有显著正向作用,农民增收在数字普惠金融与共同富裕关系中发挥中介作用;数字普惠金融的积极影响存在“边际效应”非线性递增,且农民增收能够调节数字普惠金融的非线性溢出效应;数字普惠金融对共同富裕的积极影响具有空间溢出特点,且呈“东部>中部>西部”区域异质性。通过推动数字普惠金融优先发展、努力促进区域协调发展以及充分带动农民增收,能够加快实现共同富裕。 展开更多
关键词 数字普惠金融 共同富裕 非线性模型 农民增收
下载PDF
论普惠金融的数字司法源头治理
17
作者 杨力 《交大法学》 CSSCI 北大核心 2024年第6期101-114,共14页
普惠金融纠纷已成为数字化源头治理的重点领域。普惠金融的不良贷款率上升,已接近不良贷款率的容忍限度。因此,既要从本源上诊断该类矛盾的成因,又要关注不良处置存在的挑战。数字化对社会联结的再定义,因其具有深刻鲜明的动态性、精准... 普惠金融纠纷已成为数字化源头治理的重点领域。普惠金融的不良贷款率上升,已接近不良贷款率的容忍限度。因此,既要从本源上诊断该类矛盾的成因,又要关注不良处置存在的挑战。数字化对社会联结的再定义,因其具有深刻鲜明的动态性、精准性、协同性特性,故可以有效提高普惠金融的风险防控和不良资产处置效率。数字化不仅影响了普惠金融纠纷治理的主体之间关系,而且亟须进一步完成普惠金融矛盾治理的范式转型,包括“宽框架”的双体系协同、全链条的数字化平台构建、司法裁判指引的功能定位。当然,普惠金融矛盾的解决需要完善社会化协同的宏观治理体系,创新普惠导向的微观治理机制。其中,数字化源头治理需要从供给侧、需求侧和外部环境等多个维度出发,通过创新和改革来解决现存的挑战。 展开更多
关键词 普惠金融纠纷 数字化 不良处置 赋强公证 源头治理
下载PDF
轴承钢滚动接触疲劳诱发白蚀区的研究进展
18
作者 付悍巍 冯绍晨 《轴承》 北大核心 2024年第11期12-19,共8页
白蚀区是轴承钢在滚动接触疲劳条件下出现的一种由夹杂物和碳化物诱发的特殊且重要的显微组织变化,与轴承钢的寿命密切相关。白蚀区已经被深入研究了70多年且取得了相当的进展,但关于白蚀区仍有许多关键科学问题有待解答。对白蚀区形成... 白蚀区是轴承钢在滚动接触疲劳条件下出现的一种由夹杂物和碳化物诱发的特殊且重要的显微组织变化,与轴承钢的寿命密切相关。白蚀区已经被深入研究了70多年且取得了相当的进展,但关于白蚀区仍有许多关键科学问题有待解答。对白蚀区形成的应力环境进行了阐释,并对白蚀区中纳米晶粒、碳化物溶解、整体贫碳等显微结构特点和基于剧烈塑性变形的显微组织演变机理的研究进展进行了总结,基于当前的研究进展,认为应减少对白蚀区进行过量的显微组织表征,更多关注白蚀区形成过程的若干关键科学问题和悖论。白蚀区的研究对轴承钢加工制造及热处理过程具有重要指导意义,通过优化轴承钢的生产工艺,调控抑制白蚀区形成的显微组织,从而实现轴承钢的长寿命目标。 展开更多
关键词 滚动轴承 轴承钢 接触疲劳 疲劳裂纹 显微组织 非金属夹杂物
下载PDF
高校非学历教育服务人才强国战略
19
作者 李盛兵 周大志 《现代大学教育》 CSSCI 北大核心 2024年第5期1-5,110,共6页
非学历教育是高校人才培养的重要组成部分,是建设全民终身学习型社会以及服务国家战略和经济社会发展的重要途径。在建设教育强国和人才强国的目标驱动下,高校非学历教育既肩负着通过面向社会办学提升广大劳动者的知识、技术和职业素养... 非学历教育是高校人才培养的重要组成部分,是建设全民终身学习型社会以及服务国家战略和经济社会发展的重要途径。在建设教育强国和人才强国的目标驱动下,高校非学历教育既肩负着通过面向社会办学提升广大劳动者的知识、技术和职业素养的重任,同时也是高校教师学术成长不可或缺的条件。我国高校非学历教育规模庞大、形式多样、属性不一,需要进行更深入的理论研究,强化政策激励。本期的4篇文章分别从高校非学历教育服务人才强国建设、非学历教育的转型发展、非学历教育与教师学术成长、非学历教育与科技发展等方面进行理路分析和政策分析,以期引发学界进一步深化高校非学历教育高质量发展的研究。 展开更多
关键词 高校非学历教育 教育转型 全民终身学习型社会 高校教师 学术成长 高质量发展
下载PDF
Non-Metallic Inclusion Distribution in Surface Layer of IF Steel Slabs 被引量:5
20
作者 ZHANG Qiao-ying WANG Li-tao +2 位作者 WANG Xin-hua LI Hong WANG Wan-jun 《Journal of Iron and Steel Research International》 SCIE EI CAS CSCD 2008年第1期70-74,共5页
Non-metallic inclusion distribution in the surface layer of IF steel slabs during unsteady casting was investigated using the original position statistic distribution analysis(OPA)method.It was found that most non-m... Non-metallic inclusion distribution in the surface layer of IF steel slabs during unsteady casting was investigated using the original position statistic distribution analysis(OPA)method.It was found that most non-metallic inclusions larger than 10 μm existed in the subsurface layers of 0.5-3.5 mm from the slab surfaces and very few large non-metallic inclusions were found in the inner regions(≥4.5 mm from slab surfaces).In addition,it was found that at high casting speed level(1.4 m/min),even a slight change of casting speed could result in a remarkable increase of the non-metallic inclusions.Thus,at high casting speed,changing the casting speed should be avoided or considerably lower speed changing rate must be used. 展开更多
关键词 IF steel transient casting slab surface layer non-metallic inclusion
原文传递
上一页 1 2 55 下一页 到第
使用帮助 返回顶部