Dual-Schottky-junctions coupling device based on ultra-longβ-Ga_(2)O_(3)single-crystal nanobelt and its photoelectric properties

High qualityβ-Ga_(2)O_(3)single crystal nanobelts with length of 2−3 mm and width from tens of microns to 132μm were synthesized by carbothermal reduction method.Based on the grown nanobelt with the length of 600μm,the dual-Schottky-junctions coupling device(DSCD)was fabricated.Due to the electrically floating Ga_(2)O_(3)nanobelt region coupling with the double Schottky-junctions,the current I_(S2)increases firstly and rapidly reaches into saturation as increase the voltage V_(S2).The saturation current is about 10 pA,which is two orders of magnitude lower than that of a single Schottky-junction.In the case of solar-blind ultraviolet(UV)light irradiation,the photogenerated electrons further aggravate the coupling physical mechanism in device.I_(S2)increases as the intensity of UV light increases.Under the UV light of 1820μW/cm^(2),I_(S2)quickly enters the saturation state.At V_(S2)=10 V,photo-to-dark current ratio(PDCR)of the device reaches more than 104,the external quantum efficiency(EQE)is 1.6×10^(3)%,and the detectivity(D*)is 7.5×10^(12)Jones.In addition,the device has a very short rise and decay times of 25−54 ms under different positive and negative bias.DSCD shows unique electrical and optical control characteristics,which will open a new way for the application of nanobelt-based devices.

Coupling strength effect on shot noise in boron devices

The shot noise properties in boron devices are investigated with a tight-binding model and the non-equilibrium Green＇s function. It is found that the shot noise and Fano factors can be tuned by changing the structures, the size, and the coupling strength. The shot noise is suppressed momentarily as we switch on the bias voltage, and the electron correlation is significant. The Fano factors are more sensitive to the ribbon width than to the ribbon length in the full coupling context. In the weak-coupling context, the Fano factors are almost invariant with the increase of length and width over a wide bias range.

Noise analysis and measurement of time delay and integration charge coupled device

Time delay and integration （TDI） charge coupled device （CCD） noise sets a fundamental limit on image sensor performance, especially under low illumination in remote sensing applications. After introducing the complete sources of CCD noise, we study the effects of TDI operation mode on noise, and the relationship between different types of noise and number of the TDI stage. Then we propose a new technique to identify and measure sources of TDI CCD noise employing mathematical statistics theory, where theoretical analysis shows that noise estimated formulation converges well. Finally, we establish a testing platform to carry out experiments, and a standard TDI CCD is calibrated by using the proposed method. The experimental results show that the noise analysis and measurement methods presented in this paper are useful for modeling TDI CCDs.

Charge Couple Device-Based Systemfor3-di mensional Real Ti me Positioning on the Assessment of Segmental Range of Motion of Lumbar Spine

Objective： To observe the tested results of the segmental range of motion （ROM） of lumbar spine by charge couple device （CCD）-based system for 3-dimensional real-time positioning （CCD system）, and to analyze its clinical significance. Methods： Seven patients with lumbar joint dysfunction and 8 healthy subjects were tested twice by the CCD-based system with an interval of 10 min. Results： The ROM of the patients was obviously lesser than that of the healthy subjects. The measuring data of segmental ROM of lumbar spine by CCD system is correlated significantly to the same data checked later on the same subjects in every direction of the movements. The differences between two checks are usually less than 1 degree. Conclusion： Specially designed CCD based system for 3-dimensional real-time positioning could objectively reflect the segmental ROM of lumbar spine. The system would be of great clinical significance in the assessment of the biomechanical dysfunction of lumbar spine and the effect of the treatment applied.

Investigating the Thermal Stress of Millisecond Pulsed Laser Irradiation on Charge-Coupled Devices

In this study, a two-dimensional model describing thermal stress on a charge-coupled device (CCD) induced by ms laser pulses was examined. Considering the nonlinearity of the CCD’s material parameters and the melting phase transition process of aluminum electrode materials was considered by using equivalent specific heat capacity method, the physical process where a laser pulse irradiating a CCD pixel array was simulated using COMSOL Multiphysics software. The temperature field and thermal stress field were calculated and analyzed. In order to clarify the mechanism producing damage on the CCD detector, Raman spectra from silicon were measured with a micro-Raman spectrometer to determine stress change in the CCD chip. The procedure presented herein illustrates a method for evaluating strain in a CCD after laser irradiation.

Surface contamination of the charge-coupled device

An experimental method to study the influence of surface contamination of a thinned, backside illuminated charge-coupled device(CCD) upon its quantum efficiency in soft X-ray region is suggested. A transmission grating spectrometer(TGS), in which the transmission grating is coupled to a thinned, backside illuminated charge coupled device, is used to measure the continuum X-ray emission from the end of cylindrical target irradiated by laser. In the measured spectra, only the carbon K absorption edge at wavelength of 4.4 um due to condensation of the vacuum oil oil the CCD surface is clearly seen. The surface contamination is considered as an effective "carbon filter" and the filter absorption to correct the quantum efficiency of the CCD camera is taken into account. The effective thickness of the carbon filter is determined by comparing the jump height of the measured spectra at 4.4um with those of the carbon absorption coefficient curves obtained from various carbon thickness. The accuracy of this method is tested by comparing the X-ray spectrum measured by the TGS with that obtained by a soft X-ray spectrometer.

Hydrodynamic Analysis of a Semi-submersible Wind-Tidal Combined Power Generation Device

Energy shortages and environmental pollution are becoming increasingly severe globally. The exploitation and utilization of renewable energy have become an effective way to alleviate these problems. To improve power production capacity, power output quality, and cost effectiveness, comprehensive marine energy utilization has become an inevitable trend in marine energy development. Based on a semi-submersible wind-tidal combined power generation device,a three-dimensional frequency domain potential flow theory is used to study the hydrodynamic performance of such a device. For this study, the RAOs and hydrodynamic coefficients of the floating carrier platform to the regular wave were obtained. The influence of the tidal turbine on the platform in terms of frequency domain was considered as added mass and damping. The direct load of the tidal turbine was obtained by CFX.FORTRAN software was used for the second development of adaptive query workload aware software, which can include the external force. The motion response of the platform to the irregular wave and the tension of the mooring line were calculated under the limiting condition(one mooring line breakage). The results showed that the motion response of the carrier to the surge and sway direction is more intense, but the swing amplitude is within the acceptable range. Even in the worst case scenario, the balance position of the platform was still in the positioning range, which met the requirements of the working sea area. The safety factor of the mooring line tension also complied with the requirements of the design specification. Therefore, it was found that the hydrodynamic performance and motion responses of a semi-submersible wind-tidal combined power generation device can meet the power generation requirements under all design conditions, and the device presents a reliable power generation system.

Feedforward compensation of the insertion devices effects in the SSRF storage ring

The lattice of the Shanghai Synchrotron Radiation Facility(SSRF) storage ring was upgraded in the Phase-II beamline project, and thus far, 18 insertion devices(IDs) have been installed. The IDs cause closed-orbit distortions, tune drift, and coupling distortions in the SSRF storage ring, all of which are significant issues that require solutions. In this study, an ID orbit feedforward compensation system based on a response matrix using corrector coils was developed, and it was applied to all commissioned IDs in the SSRF storage ring. After correction, the maximum ID-induced horizontal and vertical orbit distortions were less than 5.0 and 3.5 μm, respectively. Some interesting phenomena observed during the measurement process were explained. Additionally, optical and coupling feedforward systems were developed using quadrupole and skew quadrupole magnets installed on the front and back of elliptically polarizing undulators(EPUs). Moreover, over nearly four months of operation, the developed strategy delivered a satisfactory performance in the SSRF storage ring.

Study on signal intensity of low field nuclear magnetic resonance via an indirect coupling measurement

We carry out an ultra-low-field nuclear magnetic resonance （NMR） experiment based on high-T c superconducting quantum interference devices （SQUIDs）. The measurement field is in a micro-tesla range （～10 μT-100 μT） and the experiment is conducted in a home-made magnetically-shielded-room （MSR）. The measurements are performed by the indirect coupling method in which the signal of nuclei precession is indirectly coupled to the SQUID through a tuned copper coil transformer. In such an arrangement, the interferences of applied measurement and polarization field to the SQUID sensor are avoided and the performance of the SQUID is not destroyed. In order to compare the detection sensitivity obtained by using the SQUID with that achieved using a conventional low-noise-amplifier, we perform the measurements using a commercial room temperature amplifier. The results show that in a wide frequency range （～1 kHz-10 kHz） the measurements with the SQUID sensor exhibit a higher signal-to-noise ratio. Further, we discuss the dependence of NMR peak magnitude on measurement frequency. We attribute the reduction of the peak magnitude at high frequency to the increased field inhomogeneity as the measurement field increases. This is verified by compensating the field gradient using three sets of gradient coils.

Tunable terahertz transmission behaviors and coupling mechanism in hybrid MoS_(2)metamaterials

A hybrid metamaterial with the integration of molybdenum disulfide(MoS_(2))overlayer is proposed to manipulate the terahertz(THz)wave.The simulated results indicate that the introduction of MoS_(2) layer could significantly modify the resonant responses with large resonance red-shift and bandwidth broadening due to the depolarization field effect,especially for the structure on the small permitivity substrate.Additionally,the wide-band modulator in off-resonant region and a switch effect at resonance can be achieved by varying the conductivity of MoS_(2) layer.Further theoretical calculations based on the Lorentz coupling model are consistent with the simulated results,explicating the response behaviors originate from the coupling between MoS_(2) overlayer and the metastructure.Our results could provide a possibility for active control THz modulator and switchable device based on the MoS_(2) overlayer and advance the understanding of the coupling mechanism in hybrid structures.

Study on damage-stress loss coupling model of rock and prestressed anchor cable in dry-wet environment

The loss of anchoring force is one of the problems to be solved urgently.The anchorage loss is a key factor causing the failure of anchoring engineering,so it is crucial to study the time-dependent variation of anchoring force.Alternating dry and wet(D-W)conditions have a significant effect on deformation of rock.The anchoring system is composed of anchoring components and rock mass,and thus rock deformation has a significant impact on the loss of anchoring force.Quantifying rock deformation under the effects of D-W cycles is a prerequisite to understanding the factors that influence loss of anchoring force in anchor bolts.In this study,we designed an anchoring device that enabled real-time monitoring of the variation in strain during D-W periods and rock testing.Nuclear magnetic resonance(NMR)measurements showed that under D-W conditions,the increment in porosity was smaller for prestressed rock than unstressed rock.The trends of prestress loss and strain variation are consistent,which can be divided into three characteristic intervals:rapid attenuation stage,slow attenuation stage and relatively stable stage.At the same stress level,the rate of stress loss and strain for the soaking specimen was the highest,while that of the dried specimen was the lowest.In the same D-W cycling conditions,the greater the prestress,the smaller the strain loss rate of the rock,especially under soaking conditions.The characteristics of pore structure and physical mechanical parameters indicated that prestress could effectively suppress damage caused by erosion related to D-W cycles.The study reveals the fluctuation behavior of rock strain and prestress loss under D-W conditions,providing a reference for effectively controlling anchoring loss and ideas for inventing new anchoring components.

Pressure control method and device innovative design for deep oil in-situ exploration and coring

Deep oil exploration coring technology cannot accurately maintain the in-situ pressure and temperature of samples, which leads to a distortion of deep oil and gas resource reserve evaluations based on conventional cores and cannot guide the development of deep oil and gas resources on Earth. The fundamental reason is the lack of temperature and pressure control in in-situ coring environments. In this paper, a pressure control method of a coring device is studied. The theory and method of deep intelligent temperature-pressure coupling control are innovatively proposed, and a multifield coupling dynamic sealing model is established. The optimal cardinality three term PID (Proportional-Integral-Differential) intelligent control algorithm of pressure system is developed. The temperature-pressure characteristic of the gas-liquid two-phase cavity is analyzed, and the pressure intelligent control is carried out based on three term PID control algorithms. An in-situ condition-preserved coring (ICP-Coring) device is developed, and an intelligent control system for the temperature and pressure of the coring device is designed and verified by experiments. The results show that the temperature-pressure coupling control system can effectively realize stable sealing under temperature-pressure fields of 140 MPa and 150 °C. The temperature-pressure coupling control method can accurately realize a constant pressure inside the coring device. The maximum working pressure is 140 MPa, and the effective pressure compensation range is 20 MPa. The numerical simulation experiment of pressure system control algorithm is carried out, and the optimal cardinality and three term coefficients are obtained. The pressure steady-state error is less than 0.01%. The method of temperature-pressure coupling control has guiding significance for coring device research, and is also the basis for temperature-pressure decoupling control in ICP-Coring.

IEC 60372-1984 “Locking devices for ball and socketcouplings of string insulator units:Dimensions and tests”标准维护的思考

随着电力系统的发展,现行的IEC 60372"Locking devices for ball and socket couplings of string insulator units:Dimensions and tests"(Third edition)1984版已经无法涵盖和适应新的特高压大吨位绝缘子产品和技术的发展,包括对应于36和40两种新的联接标记的更高强度等级的绝缘子。笔者介绍了IEC TC36/MT21工作组维护IEC 60372标准的主要内容:包括结合国际工程实践经验,将已经被广泛应用的36、40两个联接标记加入到本标准中;研究是否增加锁紧销操作试验项目;研究并修改了原标准中L2和L5错误的问题;解决了28BW型锁紧销是否在本次修订中纳入标准的问题等。

Vibration coupling effects and machining behavior of ultrasonic vibration plate device for creep-feed grinding of Inconel 718 nickel-based superalloy

Ultrasonic vibration-assisted grinding(UVAG)is an effective and promising method for machining of hard-to-cut materials.This article proposed an ultrasonic vibration plate device enabling the longitudinal full-wave and transverse half-wave(L2T1)vibration mode for UVAG.The characteristics of two-dimensional coupled vibration in different directions were analyzed on the basis of apparent elastic method and finite element method.Furthermore,a correction factor was applied to correct the frequency error caused by the apparent elastic method.Finally,the comparative experiments between the conventional creep-feed grinding and UVAG of Inconel 718 nickel-based superalloy were carried out.The results indicate that the apparent elastic method with the correction factor is accurate for the design of plate device under the L2T1 vibration mode.Compared with the conventional creep-feed grinding,the UVAG causes the reduction of grinding force and the improvement of machined surface quality of Inconel 718 nickel-based superalloy.Furthermore,under the current experimental conditions,the optimal ultrasonic vibration amplitude is determined as 6μm,with which the minimum surface roughness is achieved.

Spin-orbit coupling and spin current in mesoscopic devices

Recently,the spin-orbit coupling and spin current in nanodevice have been investigated extensively.In this paper,we review the recent progresses in this field.We introduce the real space Hamiltonian and the second quantization Hamiltonian of a typical quantum transport mesoscopic device,metal-QD-metal configuration,containing the spin-orbit interaction,e-e interactions,and magnetic field.Some noteworthy effects(e.g.,the spin-polarized current,spin accumulation,persistent spin current) originated from the spin-orbit interaction are reviewed,and the electric field induced by spin-current is mentioned.Lastly,we introduce some unsolved problems and prospects in this field.

Enhancement of morphological and emission stability of deep-blue small molecular emitter via a universal side-chain coupling strategy for optoelectronic device

Film morphology of emissive layers is crucial to the performance and stability of solution-processable organic light-emitting diodes(OLEDs). Compared to the interpenetration of conjugated polymer chain,small molecular emitter with a flexible side chain always presents easily aggregation upon external treatment, and caused π-electronic coupling, which is undesirable for the efficiency and stability of deep-blue OLEDs. Herein, we proposed a side-chain coupling strategy to enhance the film morphological an emission stability of solution-processable small molecular deep-blue emitter. In contrary to “parent” MC8 TPA,the crosslinkable styryl and vinyl units were introduced as ended unit at the side-chain of Cm TPA and OEYTPA. Interestingly, Cm TPA and OEYTPA films present a relatively stable morphology and uniform deep-blue emission after thermal annealing(160 ℃) in the atmosphere, different to the discontinuous MC8 TPA annealed film. Besides, compared to the Cm TPA and OEYTPA ones, serious polaron formation in the MC8 TPA annealed film also negative to the deep-blue emission, according to transient absorption analysis. Therefore, both Cm TPA and OEYTPA annealed film obtained at 140 ℃ present an excellent deep-blue ASE behavior with a 445 nm, but absence for MC8 TPA ones, associated with the disruption of annealed films. Finally, enhancement of device performance based on Cm TPA and OEYTPA film(~40%)after thermal annealing with a similar performance curves also confirmed the assumption above. Therefore, these results also supported the effectiveness of our side-chain coupling strategy for optoelectronic applications.

Effectiveness of Radiofrequency Inductively Coupled Plasma Sources for Space Propulsion

Evolution of geometric forms of antenna coils for radiofrequency(RF)inductively coupled plasma(ICP)sources is analyzed.Top effectiveness of flat ICPSs generating plasma"tablet"is shown.Especially effective are ICPSs using antenna coils enhanced with ferromagnetic cores(FMICPS).It is found that the design of flat ICPSs is simpler and more convenient for the arrangement of plasma diagnostics in comparison with ICPSs of other geometries.Effective flat FMICPS models of different diameters ranging from 10 cm to 100cm are considered.Recommendations are given for development engineers dealing with ICPS devices in general and with radio frequency ion thrusters(RITs)in particular.

High Power Fiber Bundle Array Coupled LDA Module

An optical fiber bundle array coupling module with high output power is presented in this paper. The device integrated the coupling technique of the high power laser diode array (LDA) and the micro-ball lenses fiber array. This module can efficiently couple the output laser of the LDA into 19 fibers array with micro-ball lens end-surface. The difference of the couple efficiency between the flat-end fiber and micro-ball-end fiber is discussed. The micro-ball lenses fiber array made of 19 fibers have the same fiber core diameter of 200 m, and then the end-surfaces of 19 fibers are fused to 19 micro-ball lenses. The micro-ball lenses fiber array are fixed precisely in the neighborhood on the V-grooves, and the fiber array has the same arrange period with the semiconductor laser units of LDA. This configuration of micro-ball lens fiber array can greatly reduce the divergence of the laser beam from all directions, and a very efficient laser beam homogenizer and shaper are obtained. Finally, high output power of 30.1 W of the fiber coupled LDA is achieved, and the maximal coupling efficiency is >83% with the numeral aperture (NA) of 0.16.

基于UIS测试的Si/SiC级联器件雪崩特性分析

与机械式断路器相比,使用半导体功率器件构成的直流固态断路器在响应时间方面有较大的优势。由低压硅金属—氧化物—半导体场效应晶体管(Si MOSFET)和高压碳化硅结型场效应晶体管(SiC JFET)构成的Si/SiC级联型器件具有优异的开断特性。半导体功率器件可靠性一直是直流固态断路器所关注的焦点问题,非箝位感性负载开关(unclamped inductive switching,UIS)测试是评估半导体功率器件可靠性的重要方法。文中通过实验和仿真的方式分析了Si/SiC级联器件在非箝位感性负载开关过程的雪崩特性。首先,通过增加器件导通时间得到了不同负载电流下的雪崩特性,结果表明,随着导通时间的增加,Si/SiC级联器件在雪崩期间出现了雪崩电压下降的异常特性。随后,通过分立式Si/SiC级联器件进行UIS测试,发现异常特性是由于SiC JFET在雪崩期间出现导通而形成的。最后,通过Si/SiC级联器件的三维电—热耦合仿真,结果表明雪崩期间SiC JFET芯片栅极铝金属层和键合线温度升高,导致SiC JFET栅极等效电阻增加,最终使得SiC JFET在雪崩期间出现导通。

综掘工作面风流调控装置与射流风幕综合调控粉尘场优化分析

为解决目前综掘工作面传统混合式通风下粉尘聚集污染严重的问题,提出了利用出风口风流调控装置与抽风口射流风幕综合调控优化粉尘场的思路。以陕北某矿综掘工作面为研究对象,建立了风流-粉尘气固耦合场有限元模型,分析了调控装置口径、调控装置右偏角、风幕出口宽度、风幕出口速度及风幕出口张角等参数对粉尘场的影响;设计了正交试验以确定最佳综合调控方案,设计搭建了实验平台进行综合调控方案准确性和降尘效果验证。结果表明:在该综掘工作面通风系统布局下,当调控装置口径1.2 m,调控装置右偏角9°,风幕出口宽度0.14 m,风幕出口速度7 m/s,风幕出口张角60°时,司机位置粉尘质量浓度和行人呼吸带高度平均粉尘质量浓度分别降低91.7%和74.9%,测试误差均在10%以下,有效改善了通风环境。