Melting Behavior of PA6 and PA6/PE Blends Crystallized from Amorphous State

Aim To investigate the melting behavior of polyamide 6 in polyamide 6/polyethy lene blends crystallized from amorphous state. Methods DSC was used to test effects of annealing temperature, annealing time, DSC scan rate, and the step wise annealing on the melting peaks of the ice water quenched specimens. Results and Conclusion Varied melting peaks of PA6 component were obtained. The degree of perfection and the crystallization degree of PA6 crystals decreased in the blends, and the crystallization degree of PA6 increased with the increasing of the annealing time. The height of the upper melting peak of reference PA6 is higher than that in blends.

Effect of MgO content in sinter on the softening–melting behavior of mixed burden made from chromium-bearing vanadium–titanium magnetite

The effect of sinter with different MgO contents on the softening-melting behavior of mixed burden made from chro- mium-bearing vanadium-titanium magnetite was investigated. The results show that with increasing MgO content in the sinter, the softening interval and melting interval increased and the location of the cohesive zone shifted downward slightly and became moderately thicker. The softening-melting characteristic value was less pronounced when the MgO content in the sinter was 2.98wt%-3.40wt%. Increasing MgO content in the sinter reduced the content and recovery of V and Cr in the dripped iron. In addition, greater MgO contents in the sinter resulted in the generation of greater amounts of high-melting-point components, which adversely affected the permeability of the mixed burden. When the softening-melting behavior of the mixed burden and the recovery of valuable elements were taken into account, proper MgO con- tents in the sinter and slag ranged from 2.98wt% to 3.40wt% and from 11.46wt% to 12.72wt%, respectively, for the smelting of burden made from chromium-bearing vanadium-titanium magnetite in a blast furnace.

Effect of melting temperature on microstructural evolutions, behavior and corrosion morphology of Hadfield austenitic manganese steel in the casting process

In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium silicate/CO_2 method, using a blind riser, and then the desired molten steel was obtained using a coreless induction furnace. The casting was performed at melting temperatures of 1350, 1400, 1450, and 1500°C, and the cast blocks were immediately quenched in water. Optical microscopy was used to analyze the microstructure, and scanning electron microscopy(SEM) and X-ray diffractrometry(XRD) were used to analyze the corrosion morphology and phase formation in the microstructure, respectively. The corrosion behavior of the samples was analyzed using a potentiodynamic polarization test and electrochemical impedance spectroscopy(EIS) in 3.5 wt% NaCl. The optical microscopy observations and XRD patterns show that the increase in melting temperature led to a decrease of carbides and an increase in the austenite grain size in the Hadfield steel microstructure. The corrosion tests results show that with increasing melting temperature in the casting process, Hadfield steel shows a higher corrosion resistance. The SEM images of the corrosion morphologies show that the reduction of melting temperature in the Hadfield steel casting process induced micro-galvanic corrosion conditions.

Wear behavior of Ti6Al4V biomedical alloys processed by selective laser melting, hot pressing and conventional casting

The aim of this work was to study the influence of the processing route on the microstructural constituents,hardness andtribological(wear and friction)behavior of Ti6Al4V biomedical alloy.In this sense,three different processing routes were studied:conventional casting,hot pressing and selective laser melting.A comprehensive metallurgical,mechanical and tribologicalcharacterization was performed by X-ray diffraction analysis,Vickers hardness tests and reciprocating ball-on-plate wear tests ofTi6Al4V/Al2O3sliding pairs.The results showed a great influence of the processing route on the microstructural constituents andconsequent differences on hardness and wear performance.The highest hardness and wear resistance were obtained for Ti6Al4Valloy produced by selective laser melting,due to a markedly different cooling rate that leads to significantly different microstructurewhen compared to hot pressing and casting.This study assesses and confirms that selective laser melting is potential to producecustomized Ti6Al4V implants with improved wear performance.

Corrosion Behavior of the S136 Mold Steel Fabricated by Selective Laser Melting

The selective laser melting(SLM) method has a great potential for fabricating injection mold with complex structure. However, the microstructure and performance of the SLM molds show significantly di erent from those manufac?tured by traditional technologies. In this study, the microstructure, hardness and especially corrosion behavior of the samples fabricated by SLM and casting were investigated. The XRD results exhibit that the γ?Fe phase is only obtained in the SLM parts, and the α?Fe peak slightly moves to low di raction angle compared with casting counterparts. Due to the rapid cooling rate, the SLM samples have fine cellular microstructures while the casting ones have coarse grains with obvious elements segregation. Besides, the SLM samples show anisotropy, hardness of side view and top view are 48.73 and 50.31 HRC respectively, which are 20% higher than that of casting ones. Corrosion results show that the SLM samples have the better anti?corrosion resistance(in a 6% FeCl3 solution for 48 h) but the deeper corrosion pits than casting ones. Finally, the performance of the SLM molds could meet the requirement of injecting production. Moreover, the molds especially present a significant decrease(20%) of cooling time and increases of cooling uniform?ity due to the customized conformal cooling channels.

Softening–melting behavior of mixed burden based on low-magnesium sinter and fluxed pellets

A low MgO content in sinter is conducive to reduce the MgO content in blast furnace slag.This study investigated the effect of MgO content in sinter on the softening–melting behavior of the mixed burden based on fluxed pellets.When the MgO content increased from 1.31 wt% to 1.55 wt%, the melting temperature of sinter increased to 1521℃.Such an increase was due to the formation of the high-meltingpoint slag phase.The reduction degradation index of sinter with 1.31 wt% MgO content was better than that of others.The initial softening temperature of the mixed burden increased from 1104 to 1126℃ as MgO content in sinter increased from 1.31 wt% to 1.55 wt%, and the melting temperature decreased from 1494 to 1460℃.The permeability index(S-value) of mixed burden decreased to 594.46 kPa·℃ under a high MgO content with 1.55 wt%, indicating that the permeability was improved.The slag phase composition of burden was mainly akermarite(Ca_(2)MgSiO_(7)) when the MgO content in sinter was 1.55 wt%.The melting point of akermarite is 1450℃, which is lower than other phases.

Reaction behavior and non-isothermal kinetics of suspension magnetization roasting of limonite and siderite

In order to develop limonite and decrease CO_(2) emissions,siderite is proposed as a clean reductant for suspension magnetization roasting(SMR) of limonite.An iron concentrate(iron grade:65.92wt%,iron recovery:98.54wt%) was obtained by magnetic separation under the optimum SMR conditions:siderite dosage 40wt%,roasting temperature 700℃,roasting time 10 min.According to the magnetic analysis,SMR achieved the conversion of weak magnetic minerals to strong magnetic minerals,thus enabling the recovery of iron via magnetic separation.Based on the phase transformation analysis,during the SMR process,limonite was first dehydrated and converted to hematite,and then siderite decomposed to generate magnetite and CO,where CO reduced the freshly formed hematite to magnetite.The microstructure evolution analysis indicated that the magnetite particles were loose and porous with a destroyed structure,making them easier to be ground.The non-isothermal kinetic results show that the main reaction between limonite and siderite conformed to the two-dimension diffusion mechanism,suggesting that the diffusion of CO controlled the reaction.These results encourage the application of siderite as a reductant in SMR.

Microstructure and Oxidation Behavior of ZrB_(2)-SiC Ceramics Fabricated by Tape Casting and Reactive Melt Infiltration

ZrB_(2)-based ceramics typically necessitate high temperature and pressure for sintering,whereas ZrB_(2)-SiC ceramics can be fabricated at 1500℃using the process of reactive melt infiltration with Si.In comparison to the conventional preparation method,reactive synthesis allows for the more facile production of ultra-high temperature ceramics with fine particle size and homogeneous composition.In this work,ZrSi_(2),B4C,and C were used as raw materials to prepare ZrB_(2)-SiC via combination of tape casting and reactive melt infiltration herein referred to as ZBC ceramics.Control sample of ZrB_(2)-SiC was also prepared using ZrB_(2) and SiC as raw materials through an identical process designated as ZS ceramics.Microscopic analysis of both ceramic groups revealed smaller and more uniformly distributed particles of the ZrB_(2) phase in ZBC ceramics compared to the larger particles in ZS ceramics.Both sets of ceramics underwent cyclic oxidation testing in the air at 1600℃for a cumulative duration of 5 cycles,each cycle lasting 2 h.Analysis of the oxidation behavior showed that both ZBC ceramics and ZS ceramics developed a glassy SiO_(2)-ZrO_(2) oxide layer on their surfaces during the oxidation.This layer severed as a barrier against oxygen.In ZBC ceramics,ZrO_(2) is finely distributed in SiO_(2),whereas in ZS ceramics,larger ZrO_(2) particles coexist with glassy SiO_(2).The surface oxide layer of ZBC ceramics maintains a dense structure because the well-dispersed ZrO_(2) increases the viscosity of glassy SiO_(2),preventing its crystallization during the cooling.Conversely,some SiO_(2) in the oxide layer of ZS ceramics may crystallize and form a eutectic with ZrO_(2),leading to the formation of ZrSiO_(4).This leads to cracking of the oxide layer due to differences in thermal expansion coefficients,weakening its barrier effect.An analysis of the oxidation resistance shows that ZBC ceramics exhibit less increase in oxide layer thickness and mass compared to ZS ceramics,suggesting superior oxidation resistance of ZBC ceramics.

MELTING BEHAVIOR OF LOW ETHYLENE CONTENT POLYPROPYLENE COPOLYMERS WITH AND WITHOUT NUCLEATING AGENTS

The melting behavior of polypropylene (PP) and low ethylene content polypropylenecopolymer with and without nucleating agent samples crystallized under both isothermal and non-isothermal conditions were studied by Differential Scanning Calorimeter (DSC) and X-raydiffraction. Multiple melting behavior were observed depending on the existence of nucleatingagent and crystallization conditions. The observed phenomena have been discussed by the effect ofnucleating agent on perfection of crystal and the melting and recrystallization of imperfect crystalto a more perfect crystal during the heating process of samples.

Thermal Behavior and Non-isothermal Kinetics of the Polyoxometalate of Ciprofloxacin with Tungstophosphoric Acid

The polyoxometalate （CPFX-HCl）3H3PW12O40·.8H2O was prepared and characterized by elemental analysis, IR spectra and TG-DTA-DTG. The thermal decomposition mechanism and non-isothermal kinetic parameters of the polyoxometalate were obtained from the analysis of TG-DTG data using the Achar equation, Coats-Redfern equation （CR）, Madhusudanan-Krishnan-Ninan equation （MKN） and Horowitz-Metzger equation （HM）. And their mathematical expressions of the kinetic compensation effect were also calculated.

Effect of trace calcium on melting behavior of Ag-Cu-Zn brazing alloy by thermal analysis kinetics

The purity of the brazing alloys applied is necessary to be improved with the increasing cleanness of steel. Calcium is easily brought into the widely ased brazing alloy, Ag-Cu-Zn, during the producing process. This paper aims at revealing the effect of calcium on the melting behavior of the brazing alloy. The thermal analysis kinetics of silver alloy with trace calcium was studied by using differential scanning calorimetry （ DSC ） , and the enthalpy peaks were analyzed by differential methods. The rate constant of phase transformation in the probable brazing temperature range goes up with increasing calcium content, according to the values of the apparent activation energy, E, and the frequeney constant, A. It is concluded that the calcium addition could improve the melting performance of Ag-Cu-Zn brazing alloy.

Thermodynamics of Molten Pool Predicted by Computational Fluid Dynamics in Selective Laser Melting of Ti6Al4V:Surface Morphology Evolution and Densification Behavior

The three-dimensional physical model of the randomly packed powder material irradiated by the laser beam was established,taking into account the transformation of the material phase,the melt spreading and the interaction of the free surface of the molten pool and the recoiling pressure caused by the material evaporation during the selective laser melting.Influence of the processing parameters on the thermal behavior,the material evaporation,the surface morphology and the densification behavior in the connection region of the molten pool and the substrate was studied.It was shown that the powder material underwent the transformation from the partial melting state to the complete melting state and finally to the overheating state with the applied laser energy density increasing from 167 J/mm^(3) to 417 J/mm^(3).Therefore,the solidified track ranged from the discontinuous tracks with the rough surface to the continuous tracks with residual porosities,then to the continuous and dense tracks and terminally to the fluctuated tracks with the increase in the laser energy density.Meanwhile,the laser energy effect depth was maintained the positive relationship with the laser energy density.The vortex velocity obtained in the free surface of the molten pool towards to the rear region in the opposite laser scan direction promoted the melt convection to the edge region of the molten pool as the laser energy density was higher than 277 J/mm^(3),demonstrating the efficient energy dissipation from the center of the irradiation region to the whole part of the molten pool and the attendant production of the sufficient melt volume.Therefore,the efficient spreading of the molten pool and the metallurgical bonding ability of the melt with the substrate was obtained at the optimized laser energy density of 277 J/mm^(3).However,the severe material evaporation would take place as the melt was overheated,resulting in the formation of the residual pores and poor surface quality.

Reduction and melting behavior of carbon composite lateritic bauxite pellets

Direct reduction of low-grade lateritic bauxite was studied at high temperature to recover Fe and beneficiate AlzO3 slag. The re- sults show that a metallization rate of 97.9% and a nugget recovery rate of 85.1% can be achieved when the reducing and melting tempera- tures are 1350 and 1480℃, respectively. Moreover, a higher-grade calcium aluminate slag （A1203 = 50.52wt%） can also be obtained, which is mainly composed of ct-A1203, hercynite （FeAI：O4）, and gehlenite （Ca2A12SiO7）. In addition, high-quality iron nuggets have been produced from low-grade lateritic bauxite. The nugget is mainly composed of iron （93.82wt%） and carbon （3.86wt%）, with almost no gangue （slag）.

Isothermal Crystallization Kinetics and Melting Behavior of POE-g-MAH Compatibilized PA11/POE Blends

A new Nylon 11（PA11）/polyethylene-octene（POE） blends compatibilized by maleic anhydride grafted mixture polyethyleneocten（POE-g-MAH） was prepared through melt blending method.The isothermal crystallization kinetics and melting behaviors of PA11/POE blends were investigated in detail by differential scanning calorimetry（DSC） and polarized optical microscope.The n values of PA11 blending with POE or POE-g-MAH are almost similar with pure PA11,which indicates that the effect of POE and POE-g-MAH on nucleation and growth of PA11 crystal is slight.The overall crystallization rate of PA11/POE blends are higher than ones of pure PA11 at the same crystallization temperatures,but they decrease significantly when POE-g-MAH is added into PA11/POE blends.DSC heating curves of both PA11 and its blends exhibit two melting peaks,but the two melting peak become weaker when POE-g-MAH is add into PA11/POE blend systems.And the spherulite size is reduced significantly by the addition of POE-g-MAH compared with pure PA11 and PA11/POE blends.

REDUCTION BEHAVIOR OF IRON ORE PELLETS CONTAININGCARBON UNDER NON-ISOTHERMAL CONDITION

The reduction behavior of iron ore pellets containing carbon under non-isothermal condition in the temperature range from 573 to 1373 K was investigated in a laboratory scale setup. The test results show that carbon content has no obvious effect on reduction degree of composite pellets (C/O mole ratio=1.0) by CO in the temperature range from 573 to 1373 K under linear temperature-rising program; reduction degree of iron ore pellets containing carbon is large in 90%CO-10%CO2 mixture than that of in 100%CO atmosphere or in 80%CO-20%CO2 mixture; the s type temperature-rising program has a better effect than that of linear one in increasing the reduction degree; and reduction degree of slower linear temperature-rising program is greater than that of faster one, but the final reduction degrees, i.e., those at the highest temperature are about the same for various CO partial pressures or temperature-rising programs. The kinetic analysis also shows that the reduction of iron ore-carbon composite pellets by CO or CO-CO2 mixture under non-isothermal condition should be controlled by surface reaction, and the apparent reduction activation energy changes with the reduction progress under various test conditions.

Melting behavior of magnesium alloy chips in thixomolding process

The samples were fabricated by 220 t thixomolded machine made by Japan Steel Works. The microstructure from the AZ91D magnesium alloy chips to the thixomolded products was investigated. Melting behavior of the chips in thixomolding process was analyzed. The evolution processing of solid phase morphology was studied,and evolution model was put forward. The results show that microstructures in outer zone of a chip and the inner zone are obviously different,and the severe distortion takes place in the brim of the chip,where the grains are observed to be bent,distorted,even broken. The severe plastic deformation region is firstly molten,then segregation area in the inner of the chip continues to melt. The liquid phase in solid phase does not formed by liquid entrapped during shearing process,but primarily induced by internal composition segregation.

A review of particulate-reinforced aluminum matrix composites fabricated by selective laser melting

Selective laser melting(SLM)is an emerging layer-wise additive manufacturing technique that can generate complex components with high performance.Particulate-reinforced aluminum matrix composites(PAMCs)are important materials for various applications due to the combined properties of Al matrix and reinforcements.Considering the advantages of SLM technology and PAMCs,the novel SLM PAMCs have been developed and researched in recent years.Therefore,the current research progress about the SLM PAMCs is reviewed.Firstly,special attention is paid to the solidification behavior of SLM PAMCs.Secondly,the important issues about the design and fabrication of high-performance SLM PAMCs,including the selection of reinforcement,the influence of parameters on the processing and microstructure,the defect evolution and phase control,are highlighted and discussed comprehensively.Thirdly,the performance and strengthening mechanism of SLM PAMCs are systematically figured out.Finally,future directions are pointed out on the advancement of high-performance SLM PAMCs.

Non-isothermal crystallization kinetics of Nylon 10T and Nylon 10T/1010 copolymers:Effect of sebacic acid as a third comonomer

Nylon 10 T and Nylon 10T/1010 samples were synthesized by direct melt polymerization. The non-isothermal crystallization kinetics of Nylon 10 T and Nylon 10T/1010 was investigated by means of differential scanning calorimetry(DSC). Jeziorny equation and Mo equation were applied to describe the non-isothermal crystallization kinetics of the Nylon 10 T and the Nylon 10T/1010. The activation energies for non-isothermal crystallization were obtained by Vyazovkin's method and Friedman's method, respectively. These results showed that Jeziorny equation and Mo equation well described the non-isothermal crystallization kinetics of the Nylon 10 T and the Nylon 10T/1010. It was found that the values of the activation energy for non-isothermal crystallization of the Nylon 10T/1010 were lower than those of the Nylon 10 T at a given temperature or relative crystallinity degree,which revealed that crystallization ability of the Nylon 10T/1010 was higher. The crystal morphology was observed by means of a polarized optical microscope(POM) and X-ray diffraction(XRD). It was found that the addition of sebacic acid comonomer not only did not change the crystal form of the Nylon 10 T, but also significantly increased the number and decreased the size of spherulites. Comparing with the Nylon 10 T, the crystallization rate was increased with the addition of the sebacic acid comonomer.

Microstructure and electrochemical corrosion behavior of selective laser melted Ti−6Al−4V alloy in simulated artificial saliva

Ti−6Al−4V alloy was fabricated via selective laser melting(SLM)to improve its corrosion resistance for implant.The microstructure and electrochemical corrosion behavior were investigated using scanning electron microscopy(SEM),electron backscatter diffraction(EBSD),transmission electron microscopy(TEM),electrochemical test and contact angle test.It can be found that the as-selective laser melted(as-SLMed)Ti−6Al−4V alloys showβcolumnar microstructure in building direction and nearly circular checkerboard microstructure in scanning direction,while the wrought and wrought+HT samples exhibit equiaxed microstructure.The as-SLMed Ti−6Al−4V alloy exhibits better corrosion resistance than the wrought and wrought+HT samples due to hydrophobicity,high grain boundary density and uniform distribution of alloying elements in simulated artificial saliva at 37℃.