Thermal Performance Analysis of Plaster Reinforced with Raffia Vinifera Particles for Use as Insulating Materials in Building

The present study focuses on the formulation of new composite consisting of plaster and raffia vinifera particle (RVP) with the purpose to reducing energy consumption. The aim of this study is to test this new compound as an insulating eco-material in building in a tropical climate. The composites samples were developed by mixing plaster with raffia vinifera particles (RVP) using three different sizes (1.6 mm, 2.5 mm and 4 mm). The effects of four different RVP incorporations rates (i.e., 0wt%, 5wt%;10wt%;15wt%) on physical, thermal, mechanicals properties of the composites were investigated. In addition, the use of the raffia vinifera particles and plaster based composite material as building envelopes thermal insulation material is studied by the habitable cell thermal behavior instrumentation. The results indicate that the incorporation of raffia vinifera particle leads to improve the new composite physical, mechanical and thermal properties. And the parametric analysis reveals that the sampling rate and the size of raffia vinifera particles are the most decisive factor to impact these properties, and to decreases in the thermal conductivity which leads to an improvement to the thermal resistance and energy savings. The best improvement of plaster composite was obtained at the raffia vinifera particles size between 2.5 and 4.0 mm loading of 5wt% (C95P5R) with a good ratio of thermo-physical-mechanical properties. Additionally, the habitable cell experimental thermal behavior, with the new raffia vinifera particles and plaster-based composite as thermal insulating material for building walls, gives an average damping of 4°C and 5.8°C in the insulated house interior environment respectively for cold and hot cases compared to the outside environment and the uninsulated house interior environment. The current study highlights that this mixture gives the new composite thermal insulation properties applicable in the eco-construction of habitats in tropical environments.

Research on thermal insulation materials properties under HTHP conditions for deep oil and gas reservoir rock ITP-Coring

Deep oil and gas reservoirs are under high-temperature conditions,but traditional coring methods do not consider temperature-preserved measures and ignore the influence of temperature on rock porosity and permeability,resulting in distorted resource assessments.The development of in situ temperaturepreserved coring(ITP-Coring)technology for deep reservoir rock is urgent,and thermal insulation materials are key.Therefore,hollow glass microsphere/epoxy resin thermal insulation materials(HGM/EP materials)were proposed as thermal insulation materials.The materials properties under coupled hightemperature and high-pressure(HTHP)conditions were tested.The results indicated that high pressures led to HGM destruction and that the materials water absorption significantly increased;additionally,increasing temperature accelerated the process.High temperatures directly caused the thermal conductivity of the materials to increase;additionally,the thermal conduction and convection of water caused by high pressures led to an exponential increase in the thermal conductivity.High temperatures weakened the matrix,and high pressures destroyed the HGM,which resulted in a decrease in the tensile mechanical properties of the materials.The materials entered the high elastic state at 150℃,and the mechanical properties were weakened more obviously,while the pressure led to a significant effect when the water absorption was above 10%.Meanwhile,the tensile strength/strain were 13.62 MPa/1.3%and 6.09 MPa/0.86%at 100℃ and 100 MPa,respectively,which meet the application requirements of the self-designed coring device.Finally,K46-f40 and K46-f50 HGM/EP materials were proven to be suitable for ITP-Coring under coupled conditions below 100℃ and 100 MPa.To further improve the materials properties,the interface layer and EP matrix should be optimized.The results can provide references for the optimization and engineering application of materials and thus technical support for deep oil and gas resource development.

The Application of Solid Waste in Thermal Insulation Materials: A Review

As socioeconomic development continues,the issue of building energy consumption has attracted significant attention,and improving the thermal insulation performance of buildings has become a crucial strategic measure.Simultaneously,the application of solid waste in insulation materials has also become a hot topic.This paper reviews the sources and classifications of solid waste,focusing on research progress in its application as insulation materials in the domains of daily life,agriculture,and industry.The research shows that incorporating household solid waste materials,such as waste glass,paper,and clothing scraps into cementitious thermal insulation can significantly reduce the thermal conductivity of the materials,leading to excellent thermal insulation properties.Insulation materials prepared from agricultural solid waste,such as barley straw,corn stalk,chicken feather,and date palm fibers,possess characteristics of lightweight and strong thermal insulation.Industrial solid waste,including waste tires,iron tailings,and coal bottom ash,can also be utilized in the preparation of insulation materials.These innovative applications not only have positive environmental significance by reducing waste emissions and resource consumption,but also provide efficient and sustainable insulation solutions for the construction industry.However,to further optimize the mix design and enhance the durability of insulation materials,continuous research is required to investigate the mechanisms through which solid waste impacts the performance of insulation materials.

Effects of Al_(2)O_(3)-SiO_(2) Raw Material Types on Properties of Anorthite Based Insulation Refractories

To optimize their Al_(2)O_(3)-SiO_(2) raw materials,anorthite based insulation refractories were prepared by the in-situ sintering process combined with the foaming method after sintering at 1350℃for 3 h,using green and pollution-free kaolin,kyanite,andalusite and sillimanite as Al_(2)O_(3)-SiO_(2) raw materials,respectively,and industrial CaCO_(3) as the CaO source.Effects of Al_(2)O_(3)-SiO_(2) raw material types on the physical properties,phase composition and microstructure were investigated.The results are as follows.All samples prepared by different Al_(2)O_(3)-SiO_(2) raw materials have hexagonal flake anorthite and a small amount of mullite and corundum.Their bulk density and thermal conductivity decrease in the order of using kaolin,andalusite,kyanite and sillimanite as the Al_(2)O_(3)-SiO_(2) raw material,but their apparent porosity increases.Moreover,in the sample with kaolin,the bonding between anorthite crystals on the pore walls is closer than that of the other samples,which is conducive to increasing the cold crushing strength.The bonding between anorthite crystals on pore walls gradually decreases in the order of using kyanite,andalusite and sillimanite as the Al_(2)O_(3)-SiO_(2) raw material,thus their cold crushing strength decreases accordingly.In comprehensive consideration,the properties of the sample from kyanite are the optimal.Its apparent porosity,thermal conductivity and cold crushing strength are 84.6%,0.141 W·m^(-1)·K^(-1) and 1.89 MPa,respectively.

Beijing Matrix Technologies introduces revolutionary insulation material Y-Warm

Since the discovery of nanoporous materials (aerogel)in 1931,there is no doubt that this material is classified as a super-insulator with the highest insulation value of any known material with the lowest thermal conductivity value of any solid.Unfortunately,the application of aerogel is severely limited due to the difficulty of handling.After eight years of research and efforts,Beijing Matrix Technologies Co.,Ltd.has met the world challenge on the combination of mechanical strength and thermal insulation.

Research on non-steam-cured and non-fired fly-ash thermal insulating materials

A thermal insulating material is synthesized via a non-steam-cured and non-fired route by using fly-ash, sorel cement and hydrogen peroxide solution as raw material. Properties such as apparent density, compressive strength, bending strength, thermal conductivity, water resistance, and thermal tolerance of this matrial are studied, some influencing factors on its performance discussed. This material has an apparent density of 360 kg/m^3, a compressive strength of 1.86 MPa, a thermal conduction coefficient of 0.072 W/（m·K）, a softening coefficient of 0.55, and a thermal tolerant temperature of 300 ℃. Test results show that this material is light in weight, of high strength, and good thermal insulation. In addition, neither steam-curing nor sintering is needed in producing it. Further more, large amount of fly ash is used in this material, making it a low cost and environment-friendly building material.

Preparation of Nanoporous Thermal Insulating Materials and Their Application as Ladle Linings

The nanoporous thermal insulating material was prepared by using fumed silica,SiC powder and glass fiber as starting materials,the appropriate thickness of the nanoporous thermal insulating material lined in ladle was discussed by the simulation method,and the effect of its application as ladle lining was investigated.The results show that the thermal conductivity of the nanoporous thermal insulating material prepared in composition of fumed silica： SiC powder： glass fiber =75： 20：5 （in mass） is 0.023 W · m^-1 · K^-1 at 1 000 ℃,the appropriate thickness of the nanoporous thermal insulating material lined in ladle is ≤ 5 mm and the average temperature of the ladle outside surface when lined with the nanoporous thermal insulating material is 95 ℃ lower than that with the ordinary thermal insulating material.

Light Weight Insulating Material Prepared from Rice Husk

Pakistan is at 12th number in the rank of rice production countries. Along with the production of 4,500 thousand metric tons of rice enormous quantity of rice husk is left as waste. Light weight thermal insulating material was prepared from rice husk. Epoxy resin was used as a binder and was mixed with rice husk to give it strength, the sample was compressed at 7000 psi to produce cylindrical shape block. The thermal conductivity of the sample A, B, C and D of thickness 1, 2, 3 and 4 cm respectively was measured 0.0241, 0.0240, 0.239 and 0.0219 watts/m-k, which was lower than the common mortar by 51.74%, therefore it could be used in buildings and roof as an insulating material. This would be a suitable alternative which would not only save energy but also solve the environmental disposal problems as well. The results are very promising and we hope insulation material prepared would be useable in hot climate regions like Pakistan in buildings to prevent heat transfer.

Investigation of Excessive Material on Insulating Properties Using Different Heat Transfer Fluid for Thermal Energy Storage Development

Though TES （thermal energy storage） is developed hugely in most of the solar power generation plants, it is less growth in implementing a modular type of TES in a solar plant, e.g., solar dish/stifling engine application. The main issue in designing the TES system is its thermal capacity of storage materials, e.g., insulator. This study is focusing on the potential waste material as an insulator for thermal energy storage applications. The insulator usage is to reduce the heat transfer between two mediums and the capability is measured by its resistance to heat flow. It is needed to obtain optimal materials to energy conversion at the same time reduce the waste generation. Therefore, a small-scale experimental testing of natural cooling process of an insulated tank within a confined room without any forced cooling system, e.g., fan. The testing is repeated by changing the insulator using the potential waste material from natural and industrial waste and also by changing the HTF （heat transfer fluid）. The analysis is performed on the relationship between heat loss and the reserved period by the insulator. The results indicate the percentage of period of the insulated tank withstands the heat compared to non-insulated tank, e.g., cotton reserved the period of 14% more than non-insulated tank to withstand the heat transfer of cooking oil to the surrounding. The paper finally justifies the most potential waste material as an insulator in different heat transfer fluids.

Research for Optimizing Porosity of Porous Thermal-insulating Materials

With the energy crisis and ecological environment deterioration, porous thermal-insulating materials become an advanced research hotspot, and the influence of pore distribution cannot be ignored. The mathematical model is established basing on the heat transfor theory, regarding the minimum heat flux density as the objective function, the constant total porosity as a constraint condition, using the BFGS method to optimize the pore distribution. The results show that when the heat flux is the minimum, in the case of the fixed total porosity, the high temperature zone has high porosity, the low temperature zone has low porosity; the maximal fluctuating amplitude of porosity between the adjacent discrete points has great impact on the thermal insulating performanee, the greater the fluctuating amplitude, the better the thermal insulating ability. After calculating the temperature field of the corresponding physical model, it can be found that the temperature gradient is non-uniform, the temperature gradient of the high temperature zone is steep, and that of the low temperature zone is gentle. These results have guiding significance for preparation of porous thermal-insulating materials.

Preparation of Ultra-light Xonotlite Thermal Insulation Material Using Carbide Slag

Using carbide slag as the calcareous materials, xonotlite thermal insulation material was successfully prepared via dynamic hydrothermal synthesis. The experimental results show that the xonotlite thermal insulation material is made up of large numbers of ＂chestnut bur shape＂ particles. Optimum conditions of calcination temperature of carbide slag, synthesis reaction temperature and time, stirring rate, CaO/SiO2 mol ratio, water/solid weight ratio, amount of fiberglass, molding pressures, dryness temperatures and the presence of dispersant （glycol and polyvinyl alcohol） favor the preparation of xonotlite thermal insulation material. The evaluation of xonotlite thermal insulation material reveals that the product is ultra-light and excellent in physical performances. Such a little amount of impurities in carbide slag has no effect on the phase, morphology, stability at high temperature and physical performances of products.

Study on Glass Fiber Dispersion Technology in SiO_2 Aerogel-glass Fiber Composite Insulation Materials

In order to improve the mechanical properties of SiO_2 aerogel-glass fiber composites, effects of different solvents(cyclohexane, n-hexane, ethanol, acetone) and different dispersing modes(planetary ball milling, ultrasonic dispersion and mechanical stirring) and dispersing duration(10-40 min) on the dispersion of chopped alkali-free glass fiber bundles were studied to determine the best dispersion process. On this basis, the materials were batched according to the mass fraction of SiO_2 aerogel powder to chopped alkali free glass fiber bundles of 90:10, and a certain amount of zinc oxide light-screening agent and phenolic resin binder were added. SiO_2 aerogel glass fiber composite specimens were prepared by direct adding chopped alkali free glass fiber bundles and pre-dispersed chopped alkali free glass fiber bundles, respectively. The cold crushing strength and the thermal conductivity at different surface temperatures(300, 400, 500 and 600 ℃, respectively)of the specimens were measured. The results show that:(1) the optimum dispersion process of chopped alkali-free glass fiber bundles is using ethanol as solvent and mechanical stirring for 30 min;(2) pre-dispersion of chopped alkali-free glass fiber bundles has little effect on the thermal conductivity of SiO_2 aerogel-glass fiber composites but can improve the cold crushing strength.

Carbon foams prepared from coal tar pitch for building thermal insulation material with low cost

A new approach is provided to resolve the large-scale applications of coal tar pitch. Carbon foams with uniform pore size are prepared at the foaming pressure of normal pressure using coal tar pitch as raw materials. The physical and chemical performance of high softening point pitch(HSPP) can be regulated by vacuumizing owing to the cooperation of vacuumizing and polycondensation. Results indicate that the optimum softening point and weight ratio of quinoline insoluble are about 292℃ and 65.7%, respectively. And the optimum viscosity of HSPP during the foaming process is distributed in the range of 1000-10000 Pa·s. The resultant carbon foam exhibits excellent performance, such as uniform pore structure, high compressive strength(4.7 MPa), low thermal conductivity(0.07 W·m^(-1) ·K^(-1)), specially, it cannot be fired under the high temperature of 1200 ℃.Thus, this kind of carbon foam is a potential candidate for thermal insulation material applied in energy saving building.

Sustainability of Sheep Fleece Utilization in Jordan as an Insulation Material to Decrease Environmental Pollution, Increase Farmers’ Income, and Create New Job Opportunities

This study is planned to investigate the problems associated with the wasted sheep fleece in Jordan and to suggest methods to decrease its environmental impact. Results indicate that sheep fleece in Jordan makes an excellent resource for buildings insulation material. A linear regression model is used to predict sheep number for the period (2017-2030). Based on the predicted number of Sheep an estimated annual average production of wool is found for the period (2017-2030) to be (3.586 × 103 ton). The average cost per kg of fleece produced is calculated to be 0.39 JD, and the estimated price of fleece per head, if market is available for raw fleece, is 1 JD. Average annual financial losses by farmers are calculated to be (3.743 × 106 JD) for the period 2002-2016, and they were estimated to be (9.421 × 106 JD) for the years 2017-2030. Physical characteristics of sheep-wool are presented and compared to other competitive insulation materials (polystyrene and rockwool). Sustainability of sheep-wool production to be utilized as an insulation material is found to be an excellent solution to the huge waste of wool with respect to farmers and National income and to the problems associated with environmental impact. Results can be generalized to similar cases worldwide.

POSTBUCKLING RESPONSE OF CANTILEVER BEAMS OF NON-LINEAR ELASTIC MATERIAL SUBJECTED TO SUBTANGENTIAL FOLLOWER FORCES

This paper deals with the problem of the postbuckling response of a thin cantilever beam ofnon-linear material, subjected to subtangential follower forces. Based on the well-knownBernoulli-Euler bending moment-curvature relation, the proposed problem is reduced to a specialeigenvalue problem of non-linear differential equation. An approximate solution is achieved byusing a simple and very effective technique, which leads to reliable results even in the case of verylarge deflections. The initial postbuckling path depending on the subtangential follower forces inequilibrium is then obtained. Moreover, the individual and coupling effect of the subtangential fol-lower force, the material non-linearity and the beam slenderness ratio on the initial postbucklingpath are also discussed in detail.

Effect of Pyrophyllite Addition on Properties of Lightweight Insulation Refractory Materials

To solve the problem of over-high density of lightweight insulation refractory bricks prepared with fly ash, new lightweight insulation refractory materials with density 〈 0. 89 g · cm^-3 were .synthesized using pyrophyl-lite, .fly ash, and Suzhou clay as the main starting materials and saw dast as the pore forming substance, and controlling the addition of the pyrophyllite （20%, 30% , and 40% by mass ） and the treating temperature （1 250, 1 300, 1 350, and 1 400 ℃ ）. The synthesized materials were characterized by the XRD, SEM and the thermal conductivity measuring in.strument. The results show at pyrophyllite addition of 30% and treat temperature of l 400 ℃ , the material can achieve linear shrinkage of 6. 6%, apparent porosity of 57%, bulk density of 0. 75 g · cm^-3, compressive strength of 2.7 MPa, and thermal conductivity at 350 ℃ of 0. 152 -0. 216 W·（ m·K）^-1.This indicates that the pyrophyllite decomposition at high temperatures forms mullite and amorphous quartz introducing volume expansion, which counteracts some shrinkage at high temperatures. So it is feasible to use pyrophyllite, fly ash waste and clay to prepare lightweight insulation refractory materials.

Preparation and Characterization of Sandwich Structured Materials with Interesting Insulation and Fire Resistance

A cellular material in the form of 3-layered sandwich structure material was prepared via sole use of mechanical stirring without any use of a foaming agent,while Tween-80 was employed as a foam stabilizer via a developed in-situ mold casting.The resulting structure displayed a good appearance with no visual defects.The 3-layered composition of the sandwish structure,“nonporous resin layer-porous foam layer-nonporous resin layer”,was examined in terms of the microstructure,density&density distribution,pulverization ratio,mechanical strength,insulation and flame retardant performance.It was indicated from the results that the bonding between the resin layer and foam layer was tight,while the tensile rupture always occurred in the porous layer.Also,the density of the sandwich structure material was symmetrical with“saddle”distribution,and a uniform density for any given layer.The increase in the density at the interface layer provided a good interpretation for the tensile rupture never occurred at the interface.The brittleness resistance of the developed material was significantly improved,and the pulverization ratio was sharply decreased from 9.93%to 0.31%.The material acquired a thermal conductivity and limiting oxygen index(LOI)of 0.0241 W/m⋅K and 29.92%,respectively,indicating potential use of such materials broadly in fields of insulation and flame retardancy.

Analysis of the Performances of a New Type of Alumina Nanocomposite Structural Material Designed for the Thermal Insulation of High-Rise Buildings

The sol-gel method is used to prepare a new nano-alumina aerogel structure and the thermal properties of this nanomaterial are investigated comprehensively using electron microscope scanning,thermal analysis,X-ray and infrared spectrometer analysis methods.It is found that the composite aerogel alumina material has a multi-level porous nano-network structure.When employed for the thermal insulation of high-rise buildings,the alumina nanocomposite aerogel material can lead to effective energy savings in winter.However,it has almost no energy-saving effect on buildings where energy is consumed for cooling in summer.

Preparation and Properties of TiO2-Coated Hollow Glass Microspheres as Thermal Insulation Materials for Energy-Saving Buildings

A hollow glass microsphere(HGM)/TiO2 composite hollow sphere was successfully prepared via a simple precipitation method.The TiO2 coating layers grew on the surface of the HGMs that range from 20 to 50μm in diameter as nanoparticles with the formation of the SiO Ti bonds.The growth mechanism accounting for the formation of the TiO2 nanolayers was proposed.The morphology,composition,thermal insulation properties,and visible-near infrared(VIS-NIR)refl ectance of the HGMs/TiO2 composite hollow spheres were characterized.The VIS-NIR reflectance of the HGMs/TiO2 composite hollow spheres increased by more than 30%compared to raw HGMs.The thermal conductivity of the particles is 0.058 W/(m K).The result indicates that the VIS-NIR reflectance of the composite hollow spheres is strongly influenced by the coating of TiO2.The composite hollow spheres were used as the main functional filler to prepare the organic-inorganic composite coatings.The glass substrates coated by the organic-inorganic coatings had lower thermal conductivity and higher near infrared reflectivity.Therefore,the HGMs/TiO2 composite hollow spheres can reflect most of the solar energy and effectively keep out the heat as a thermal insulation coating for energy-saving constructions.